Mercury 90 (3 CYL.) (0T980000 THRU 0T999999) Outboard Motor Parts Diagram & Catalog – Free PDF Download

by JLM Marine 30 Apr 2025 0 Comments

Mercury 90 (3 CYL.) Outboard Motor Parts Diagram & Catalog – Free PDF Download

Accessories

Below is the parts list for Mercury 90 (3 CYL.) Accessories:

Position No.	Part Name	OEM Number	Supersedes
-	ANTI-ICING KIT, Carburetor	828155A4
-	EXTENSION KIT, (2.5) (2.50 Inch Black) Comment: (Use with 3 Jaw Reverse Clutch)	816696A8
-	EXTENSION KIT, (2.5) (2.50 Inch Gray) Comment: (Use with 3 Jaw Reverse Clutch)	816696A9
-	EXTENSION KIT, (2.5) Comment: (Use with 6 Jaw Reverse Clutch)	816696A10	816696A11 (Use with 6 Jaw Reverse Clutch)
-	EXTENSION KIT Comment: (5 Inch Black)	12092A13
-	EXTENSION KIT Comment: (5 Inch Gray)	12092A14
-	FLUSHING ATTACHMENT Comment: (Not for use on Jet Model Outboards)	44357Q2
-	HOSE ASSEMBLY, Fuel (8 Feet) Comment: (With Quick Disconnect)	32-877680Q8
-	HOSE ASSEMBLY, Fuel (12 Feet) Comment: (With Quick Disconnect)	32-877680Q12	32-858620Q12, 32-858620A12, 32-827927A12 (With Quick Disconnect)
-	HOSE ASSEMBLY, Fuel (8 Feet) Comment: (With Quick Disconnect Engine End Only)	32-877681Q8
-	HOSE ASSEMBLY, Fuel (12 Feet) Comment: (With Quick Disconnect Engine End Only)	32-877681Q12	32-804792Q12, 32-804792Q, 32-858621Q12, 32-858621A12, 32-17146A12 (With Quick Disconnect Engine End Only)
-	HOSE ASSEMBLY, Fuel (12 Feet) Comment: (No Fittings)	32-877683Q12	32-858623Q12, 32-858623A12, 32-822379A12, 32-819380A12, FA599752, FS409752, 32-819380A 3, F216752, FA409752, F289752, FA178752, FA216752, FA284752, FA289752, FS409952 (No Fittings)
-	MERCATHODE KIT	88334A2
-	SWITCH KIT, Trim (10.00 Feet) (With or Without Tiller)	87-18286A18
-	TILLER HANDLE ADAPTOR KIT Comment: (Jet 65)	850000A3
-	TRIM AND TILT KIT	826729A10	826729A09, 826729A08, 826729A07, 826729A 4
-	STEERING HANDLE KIT Comment: (Black)	12022A40
-	VISUAL WARNING SYSTEM Comment: (Low Oil/Overheat)	17334A2
-	REGULATOR KIT, Voltage	88825A6
-	FLUSH KIT, Coastal	858566A1

Attenuator Plate

Below is the parts list for Mercury 90 (3 CYL.) Attenuator Plate:

Position No.	Part Name	OEM Number	Supersedes
1	COVER ASSEMBLY, Attenuator	42969A3
2	CAP	19-815784	22-14685
3	GASKET	27-828479
4	NOT SOLD SEPARATE, Decal-Timing	NSS
5	NOT SOLD SEPARATE, Decal-Caution	NSS
6	SCREW, (#10-16 x .600)	10-878609	10-812832 1
7	PLATE ASSEMBLY, Attenuator	42970A2
8	WASHER	12-4002217
9	NUT	11-826365
10	CUP	39519
11	LATCH	98889
12	GASKET	27-151724
13	LINK	8252041
14	ROLLER	67748
15	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
16	LINK ROD Comment: (Oil Injection)	8M0084744
17	ARM ASSEMBLY	11399A1
18	SCREW, (M5 x 6)	10-40056103
19	WASHER, (.203 x .500 x .032)	12-8M0204666
20	HOSE, (.187) (26.00 Inches Bulk) (Cut ot 1.50 Inch Length) Comment: (Electric)	32-9912878
21	HOSE, (.187) (26.00 Inches Bulk) (Cut ot 3.25 Inch Length) Comment: (Electric)	32-9912878
21	HOSE, (.187) (26.00 Inches Bulk) (Cut ot 5.25 Inch Length) Comment: (Manual)	32-9912878
22	HOSE, (.187) (26.00 Inches Bulk) (Cut ot 5.25 Inch Length) Comment: (Electric/Manual)	32-9912878
23	FITTING TEE Comment: (Electric)	22-830285
-	GASKET SET, Powerhead	27-43004A99
-	REPAIR KIT, Carburetor	1395-8236354
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection)	898208A02	855530T98, 855530A98 (Non Oil Injection)
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 1B227000 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 1B227000 & Up
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 0P401000 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 0P401000 & Up
-	POWERHEAD ASSEMBLY Comment: (Oil Injection)	809837T97	809837A97, 809837A96, 15081A95, 809837A98 (Oil Injection)

Bleed System

Below is the parts list for Mercury 90 (3 CYL.) Bleed System:

Position No.	Part Name	OEM Number	Supersedes
1	TUBING, (240.00 Inches Bulk) (Cut to 12.50 Inch Length)	32-892024122	32-99130122
2	TUBING, (240.00 Inches Bulk) (Cut to 6.00 Inch Length)	32-892024122	32-99130122
3	TUBING, (240.00 Inches Bulk) (Cut to 3.50 Inch Length)	32-892024122	32-99130122
4	TUBING, (240.00 Inches Bulk) (Cut to 2.50 Inch Length)	32-892024122	32-99130122
5	FITTING, Tee	22-59169003
6	CHECK VALVE	21-149126
7	FITTING	22-15133
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection)	898208A02	855530T98, 855530A98 (Non Oil Injection)
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 1B227000 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 1B227000 & Up
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 0P40100 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 0P40100 & Up
-	POWERHEAD ASSEMBLY Comment: (Oil Injection)	809837T97	809837A97, 809837A96, 15081A95, 809837A98 (Oil Injection)

Bottom Cowl

Below is the parts list for Mercury 90 (3 CYL.) Bottom Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	BOTTOM COWL ASSEMBLY, Starboard	100-8M0107327
2	GROMMET (Starboard)	25-822556003	25-822556 2
3	SEAL, (36.00 Inches)	8M0109216
4	SEAL, Lower Cowl (44.75 Inches)	8M0043167	8M0036668, 884256 4
5	BOTTOM COWL ASSEMBLY, Port	100-8M0107328	2188-821874A 1
6	GROMMET (Port)	25-822555001	25-822555
7	SEAL, (36.00 Inches)	8M0109216
8	SWITCH ASSEMBLY Comment: (Power Trim)	87-8M0042301	87-896620, 87-856990, 87-850691, 87-18286A40 (Power Trim)
9	RETAINER	8M0032848	812443 1
10	FITTING	22-813613
11	TUBING, (.312) (70.00 Inches Bulk) (Cut to 28.00 Inch Length)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
12	CHECK VALVE ASSEMBLY, Drain	21-817519A2
13	SCREW, (M6 x 40)	10-82130040
14	HANDLE Comment: (Black)	8M0041366	820000A 2 (Black)
15	BUSHING	23-812707	23-71984, 23-F286818, 23-F286828, F480818
16	WASHER, Wave	13-F2047
17	CAM	8M0001081	889566, F481777, F48177
18	WASHER	12-8M0214930
19	LOCKWASHER, (.250) Stainless Steel	13-26992
20	SCREW, (.250-20 x .620) Stainless Steel	10-28635
21	RETAINER	822363T1
22	NUT, (M6) Stainless Steel	11-401386
23	WASHER	12-8M0214930
24	PLUG Comment: (Non Power Trim/Manual Tilt Assist)	812830T01	812830 1 (Non Power Trim/Manual Tilt Assist)

Carburetor

Below is the parts list for Mercury 90 (3 CYL.) Carburetor:

Position No.	Part Name	OEM Number	Supersedes
1	CARBURETOR, (WME 105-1) Comment: (Top)(75 Manual) SN# USA-1B226999/BEL-0P400999 & Below	3301-824924T54	3301-824924T32, 3301-824924A32 (Top)(75 Manual) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME 105-2) Comment: (Center)(75 Manual) SN# USA-1B226999/BEL-0P400999 & Below	3301-824924T55	3301-824924T33, 3301-824924A33 (Center)(75 Manual) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME 105-3) Comment: (Bottom)(75 Manual) SN# USA-1B226999/BEL-0P400999 & Below	3301-824924T56	3301-824924T34, 3301-824924A34 (Bottom)(75 Manual) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME 76-1) Comment: (Top)(75 Manual) SN# USA-1B227000/BEL-0P401000 & Up	3301-824924T26	3301-824924A26, 3301-824924A11 (Top)(75 Manual) SN# USA-1B227000/BEL-0P401000 & Up
1	CARBURETOR, (WME 76-2) Comment: (Center)(75 Manual) SN# USA-1B227000/BEL-0P401000 & Up	3301-824924T27	3301-824924A27, 3301-824924A12 (Center)(75 Manual) SN# USA-1B227000/BEL-0P401000 & Up
1	CARBURETOR, (WME 76-3) Comment: (Bottom)(75 Manual) SN# USA-1B227000/BEL-0P401000 & Up	3301-824924T28	3301-824924A28, 3301-824924A13 (Bottom)(75 Manual) SN# USA-1B227000/BEL-0P401000 & Up
1	CARBURETOR, (WME 77-1) Comment: (Top)(75 Electric-Handle) SN# USA-1B227000/BEL-0P401000 & Up	3301-824924T29	3301-824924A29, 3301-824924A14 (Top)(75 Electric-Handle) SN# USA-1B227000/BEL-0P401000 & Up
1	CARBURETOR, (WME 77-2) Comment: (Center)(75 Electric-Handle) SN# USA-1B227000/BEL-0P401000 & Up	3301-824924T30	3301-824924A30, 3301-824924A15 (Center)(75 Electric-Handle) SN# USA-1B227000/BEL-0P401000 & Up
1	CARBURETOR, (WME 77-3) Comment: (Bottom)(75 Electric-Handle) SN# USA-1B227000/BEL-0P401000 & Up	3301-824924T31	3301-824924A31, 3301-824924A16 (Bottom)(75 Electric-Handle) SN# USA-1B227000/BEL-0P401000 & Up
1	CARBURETOR, (WME-114-1) Comment: (Top)(75 Electric-Non Handle) SN# USA-1B227000/BEL-0P401000 & Up	3301-824924T63
1	CARBURETOR, (WME-114-2) Comment: (Center)(75 Electric-Non Handle) SN# USA-1B227000/BEL-0P401000 & Up	3301-824924T64
1	CARBURETOR, (WME-114-3) Comment: (Bottom)(75 Electric-Non Handle) SN# USA-1B227000/BEL-0P401000 & Up	3301-824924T65
1	CARBURETOR, (WME 103-1) Comment: (Top)(75 Electric Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below	3301-824924T48	3301-824924T38, 3301-824924T23, 3301-824924A23, 3301-824924A 8 (Top)(75 Electric Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME 103-2) Comment: (Center)(75 Electric Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below	3301-824924T49	3301-824924T39, 3301-824924T24, 3301-824924A24, 3301-824924A 9 (Center)(75 Electric Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME 103-3) Comment: (Bottom)(75 Electric Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below	3301-824924T50	3301-821679A22, 3301-821679A 6, 3301-824924T40, 3301-824924T25, 3301-824924A25, 3301-824924A10 (Bottom)(75 Electric Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME-106-1) Comment: (Top)(75 Electric Non Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below	3301-824924T57	3301-824924T35, 3301-824924A35 (Top)(75 Electric Non Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME-106-2) Comment: (Center)(75 Electric Non Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below	3301-824924T58	3301-824924T36, 3301-824924A36 (Center)(75 Electric Non Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME-106-3) Comment: (Bottom)(75 Electric Non Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below	3301-824924T59	3301-824924T37, 3301-824924A37 (Bottom)(75 Electric Non Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME 108-1 Comment: (Top)(90 Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below	3301-824854T18	3301-824854T 9 (Top)(90 Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME 108-2) Comment: (Center)(90 Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below	3301-824854T19	3301-824854T10 (Center)(90 Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME 108-3) Comment: (Bottom)(90 Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below	3301-824854T20	3301-824854T11 (Bottom)(90 Oil Injection) SN# USA-1B226999/BEL-0P400999 & Below
1	CARBURETOR, (WME-115-1) Comment: (Top)(90 Oil Injection) SN# USA-1B227000/BEL-0P401000 & Up	3301-824854T27
1	CARBURETOR, (WME-115-2) Comment: (Center)(90 Oil Injection) SN# USA-1B227000/BEL-0P401000 & Up	3301-824854T28
1	CARBURETOR, (WME-115-3) Comment: (Bottom)(90 Oil Injection) SN# USA-1B227000/BEL-0P401000 & Up	3301-824854T29
2	GASKET, Flange	27-151724
3	SCREW, Throttle Valve	10-F10155
4	VALVE, Throttle	1395-97244
5	NOT SOLD SEPARATE, Retaining Ring	NSS
6	SHAFT	F10064
7	SHAFT, Throttle Comment: (Top/Bottom)	1395-823632
8	SHAFT, Throttle Comment: (Center)(WME-103/108/114/115)	1395-8236321
9	SHAFT, Throttle Comment: (Center)(76/77/105/106)	1395-823633
10	SCREW (Top/Bottom)	1395-823634
11	SCREW, Cover Plate	1395-811220
12	COVER PLATE	1395-811221
13	NOT SOLD SEPARATE, Gasket-Cover Plate	NSS
14	NOT SOLD SEPARATE, Spring-Idle Needle	NSS
15	NOT SOLD SEPARATE, Idle Needle	NSS
16	LEVER, Throttle (Top/Bottom)	1395-8087461
17	NOT SOLD SEPARATE, Spring-Throttle Return	NSS
18	GASKET	1395-808738
19	NOT SOLD SEPARATE, Inlet Needle Valve	NSS
20	VALVE, Inlet Needle	10-95951
21	FLOAT	1395-9594
22	BOWL, Fuel	1395-811693	1395-9590
23	SCREW AND WASHER, (#8-32 x .750)	1395-808612	1399-5132
24	PLUG KIT	1395-811694	1395-9596 1
25	SEAL Comment: (Consists of 4 Seals)	1395-802731
26	JET, (.052) Comment: (WME-103/105/106/114-1)	1395-6359
26	JET, Main (.060) Comment: (WME-108)	1395-6487
26	JET, Main (.054) Comment: (WME-76/77/114-2,3)	1399-5225
26	JET, (.064) Comment: (WME-115-2,3)	1399-4216
26	JET, Main (.062) Comment: (WME-115-1)	1399-4217
-	GASKET SET, Carburetor	1395-8112231
-	REPAIR KIT, Carburetor	1395-8236354
-	GASKET SET, Powerhead	27-43004A99

Co-Pilot

Below is the parts list for Mercury 90 (3 CYL.) Co-Pilot:

Position No.	Part Name	OEM Number	Supersedes
-	CO-PILOT ASSEMBLY	56-52148A7
1	PILOT ROD	521481
2	NUT ASSEMBLY	11-8M0103848
3	SCREW, (.250-28 x 1.250)	10-56500
4	WASHER	12-77674
5	KNOB, Prong	821621
6	ROD	873491
7	BUSHING	23-521512
8	WASHER, (.323 x .563 x .063) Stainless Steel	12-8M0042642	12-70132
9	NUT, (.312-24) Stainless Steel	11-826709111	11-45592

Crankshaft, Pistons and Connecting Rods

Below is the parts list for Mercury 90 (3 CYL.) Crankshaft, Pistons and Connecting Rods:

Position No.	Part Name	OEM Number	Supersedes
1	CRANKSHAFT	493-827616T1
2	BEARING, Ball, Lower	30-43011T
3	WEAR SLEEVE	786611
4	O-RING, (.859 x .139)	25-35126
5	RING ASSEMBLY	39-818412A4
6	KEY, Woodruff	28-91800
7	GEAR ASSEMBLY	43-43019A1
8	BEARING ASSEMBLY, Roller, Upper	31-43013T3
9	SEAL, Oil	26-8M0214932
10	O-RING Comment: (2.112 X .103)(Square)	25-858225
10	O-RING, (1.989 x .070) Comment: (1.989 X .070)(Round)	25-823683	25-64067 (1.989 X .070)(Round)
11	BEARING ASSEMBLY, Roller	42943A1
12	NOT SOLD SEPARATE, Roller Bearing	NSS
13	PISTON ASSEMBLY Comment: (Standard)	2704-826191T4
13	PISTON ASSEMBLY Comment: (.015 Oversize)	2704-821896A3
13	PISTON ASSEMBLY Comment: (.030 Oversize)	2704-821896A4
14	LOCK RING	53-857196	40-52035
15	NOT SOLD SEPARATE, Piston Ring	NSS
16	RING KIT, Piston - Standard Comment: (Standard)	39-822321A12	39-822321A 8, 39-824905A12 (Standard)
16	RING KIT, Piston - .015 Oversize Comment: (.015 Oversize)	39-822321A1
16	RING SET, Piston Comment: (.030 O.S.)	39-822321A2
17	CONNECTING ROD ASSEMBLY	646-818846T6
18	WASHER	12-8M0012298	12-812876
19	BEARING, Needle	29-8M0214954
20	SCREW, (.375-24 x 1.250)	10-94320
21	BEARING/CAGE KIT	31-844338A01	31-43012A04
22	NOT SOLD SEPARATE, Roller Bearing	NSS
-	GASKET SET, Powerhead	27-43004A99
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection)	898208A02	855530T98, 855530A98 (Non Oil Injection)
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 1B227000 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 1B227000 & Up
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 0P401000 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 0P401000 & Up
-	POWERHEAD ASSEMBLY Comment: (Oil Injection)	809837T97	809837A97, 809837A96, 15081A95, 809837A98 (Oil Injection)

Cylinder Block

Below is the parts list for Mercury 90 (3 CYL.) Cylinder Block:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER BLOCK	876-898208A01	876-8947T57
1	CYLINDER BLOCK ASSEMBLY Comment: SN# 1B227000 & Up	876-898208A01	876-8947T57 SN# 1B227000 & Up
1	CYLINDER BLOCK ASSEMBLY Comment: SN# 0P401000 & Up	876-898208A01	876-8947T57 SN# 0P401000 & Up
2	SCREW, (M10 x 80)	10-4009680
3	SCREW, Adjusting (M6 x 55)	10-814776	10-42978
4	NUT, (M6) Stainless Steel	11-400212
5	CAP	42942
6	CHECK VALVE (Press-In)	21-426233
7	CARRIER ASSEMBLY	813801A1
8	CHECK VALVE	21-42657A3
9	PIN, Bearing Race	17-8M0036405	17-67296
10	PIN, Dowel - Without Hole (.375 x .625)	17-43044
11	STUD, (M10 x 136)	16-892561001	16-889607
12	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963
13	NUT, (M10)	11-40140
14	COVER	76867
15	SCREW, (M8 x 50)	10-81742750
16	COVER, Top	428842
17	CARRIER	65848
18	GROMMET	25-64872
19	POPPET VALVE	86596T
20	SPRING, (Stainless Steel)	24-42996
21	PLUG KIT	824703A1
22	NOT SOLD SEPARATE, Plug	NSS
23	SCREW, (M8 x 35 MM)	10-82127335
24	COVER Comment: (Non Oil Injection)	12621
25	GASKET Comment: (Non Oil Injection)	27-126201
26	SCREW, (M5 x 12) Comment: (Non Oil Injection)	10-82104512
27	STUD, (M6 x 44)	16-8161949
28	WASHER, (.187 x .500 x .062) Neoprene	12-8M0204663
29	WING NUT	11-816872
30	COVER ASSEMBLY	1034-9003A2
31	GASKET	27-430057
32	PLUG, Pipe (.125-27) Brass	22-328022
33	LIFTING EYE Comment: (Non Oil Injection)	823462
34	THERMOSTAT WASHER Comment: (Non Oil Injection)	12-475331
35	THERMOSTAT Comment: (Oil Injection)	14586
36	GASKET	27-8M0204714
37	GASKET	27-430068
38	COVER	8M0047619	884297, 42885 3
39	SCREW, (M8 x 35 MM)	10-82127335
40	SCREW, (#10-16 x .750)	10-69570
41	WASHER	12-94182
42	DIAPHRAGM	648771
43	SCREW, (#10-16 x .600)	10-878609	10-812832 1
44	RETAINER	44290T
45	SENDER, Temperature	787992
46	SCREW, (M8 x 35 MM)	10-82127335
47	CLAMP	54-814634
48	BOOT	99162001
49	REV LIMITER Comment: (Electric/Non Oil Injection)	821889A51	821889A40, 821889A29, 821889A19 (Electric/Non Oil Injection)
49	REV LIMITER Comment: (Manual)	821889A49	821889A41 (Manual)
49	REV LIMITER Comment: (Jet)	821889A50	821889A42 (Jet)
50	SCREW, (M6 x 30)	10-82130030
51	HARNESS ASSEMBLY, Adaptor Comment: (Oil Injection)	84-855212A1
52	PLUG, Male Comment: (Oil Injection)	13541
53	WASHER, (.203 x .500 x .032)	12-8M0204666
54	COUPLING INSERT Comment: (Saltwater)	22-857175	22-861405 (Saltwater)
55	COUPLING BODY Comment: (Saltwater)	22-857176
56	CAP Comment: (Saltwater)	19-858240	861427 (Saltwater)
57	TUBING, (.312) (70.00 Inches Bulk) Comment: (Saltwater)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80 (Saltwater)
58	TIE STRAP, (8.00 Inches) Comment: (Saltwater)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275 (Saltwater)
59	FITTING Comment: (Saltwater)	22-857219
60	FITTING Comment: (Saltwater)	22-286241
61	TIE STRAP, (11.750 Inches) Comment: (Saltwater)	54-850181
-	GASKET SET, Powerhead	27-43004A99
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection)	898208A02	855530T98, 855530A98 (Non Oil Injection)
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 1B227000 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 1B227000 & Up
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 0P401000 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 0P401000 & Up
-	POWERHEAD ASSEMBLY Comment: (Oil Injection)	809837T97	809837A97, 809837A96, 15081A95, 809837A98 (Oil Injection)

Driveshaft Housing

Below is the parts list for Mercury 90 (3 CYL.) Driveshaft Housing:

Position No.	Part Name	OEM Number	Supersedes
1	HOUSING ASSEMBLY, Driveshaft	1598-881913T01
1	HOUSING ASSEMBLY, Driveshaft Comment: (Jet)	1598-881913T02
2	STUD, (M10 x 100) Comment: (L=20 Inch Model)	16-903501
2	STUD, (M10 x 166) Comment: (LL=22.5 Inch Model)	16-8M0034445	16-816866 4 (LL=22.5 Inch Model)
2	STUD, (M10 x 227) Comment: (X-Long=25 Inch Model)	16-9035015
3	STUD, (M10 x 63) Comment: (L=20 Inch Model)	16-9035012
3	STUD, (M10 x 124) Comment: (LL=22.5 Inch Model)	16-8M0034446
3	STUD, (M10 x 190) Comment: (X-Long=25 Inch Model)	16-8M0034462	16-90350 16 (X-Long=25 Inch Model)
4	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963
5	NUT, (M10)	11-40140
6	PICKUP ASSEMBLY, Speedometer	22-85822A4
7	CONNECTOR, 90 Degree (.125-27) Nylon	22-433351
8	CONNECTOR, Straight	22-85822T
9	MOUNT	881916
10	BOLT, (M12 x 154)	10-898835001	10-42973
11	WASHER, (.875 Inch Outside Diameter)	12-30119
12	NUT, (M12)	11-8M0204662
13	CABLE ASSEMBLY, Ground	88238A10
14	SCREW, (.250-20 x .500) Stainless Steel	10-41508
15	CLAMP	8M0036786	881917
16	NUT	11-35521
17	SCREW, (M8 x 25 MM)	10-889833025
18	COVER	100-8M4500754	8M0000852, 882752
19	SCREW, (#12-24 x .620)	10-88417
20	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
21	WASHER, Neoprene	12-881976
22	SPACER KIT Comment: (X-Long=25 Inch Model)	12092A3
22	SPACER Comment: (LL=22.5 Inch Model)	816696T7
23	PIN, Dowel - Without Hole (.375 x .625) Comment: (LL/XL)(Rear)	17-43044
23	PIN, Dowel - With Hole (.375 x .625) (With Hole) Comment: (LL/XL)(Front)	17-8M0084244	17-43043 (LL/XL)(Front)
24	PLATE WASHER	892214
25	PLUG, Driveshaft Housing	19-8M0026580	19-889557

Electrical Components

Below is the parts list for Mercury 90 (3 CYL.) Electrical Components:

Position No.	Part Name	OEM Number	Supersedes
1	PLATE, Electrical	8327531
2	SCREW, (M8 x 30) Stainless Steel	10-40011150
3	WASHER	12-49436
4	BUSHING	23-8502341
5	GROMMET	25-833155
6	SCREW, (M5 x 12) Comment: (Electric)	10-82239312
7	CLAMP, Connector	8261151
8	CABLE ASSEMBLY (10 Inch)	84-88807A44
9	SCREW, (M5 x 12)	10-82239312
10	WASHER, (.203 x .406 x .040)	12-89302
11	HARNESS ASSEMBLY, Engine Comment: (Electric)	84-850043A2
12	FUSE, Yellow - 20 Ampere Comment: (Electric)	88-812619	88-860608 (Electric)
13	HARNESS ASSEMBLY, Ignition Comment: (Electric)	84-850046A2
14	CABLE ASSEMBLY, Positive - Battery Comment: (Electric)	84-88439A3
15	BOOT, Insulator - Red Comment: (Electric)	85-830233
16	CDM MODULE ASSEMBLY	827509A10	827509A 4
17	CABLE ASSEMBLY, Hi Tension	84-821945A61
18	BOOT/TERMINAL KIT	85-63709A1
19	SPARK PLUG Comment: (NGK#BUHW-2)	33-896329833	33-833C (NGK#BUHW-2)
19	SPARK PLUG Comment: (NGK#BUZHW-2)	33-14103Q
20	SCREW, (M6 x 16)	10-82129116
21	SOLENOID ASSEMBLY, (#10-32 / .3125-18 Terminals) Comment: (Electric)	89-817109A2
22	GROMMET Comment: (Electric)	25-822179
23	BUSHING Comment: (Electric)	23-8M0214955
24	NUT, Brass Comment: (Electric)	10-32,11-45076
25	CABLE ASSEMBLY, (4.00 Inches) Black Comment: (Electric)	84-88807A16
26	LOCKWASHER, (.312) Comment: (Electric)	13-8M0204647
27	NUT, (.312-18) Comment: (Electric)	11-8M0204668
28	SCREW, (M6 x 25 MM) Comment: (Electric)	10-82129125
29	REGULATOR, Voltage Comment: (Electric)	8M0084173	883072T, 854515T 1 (Electric)
30	TIE STRAP, (8.00 Inches) Comment: (Electric)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275 (Electric)
31	SCREW, (M6 x 35) Comment: (Electric)	10-82129135
32	J CLIP Comment: (Electric)	54-54457
33	CABLE ASSEMBLY, Battery - Negative Comment: (Electric)	84-88439A4
34	PLUG, Male Comment: (Electric)	13541
35	CLAMP	54-834813
36	HARNESS ASSEMBLY, Engine Comment: (Manual)	84-850044A2
37	TIE STRAP, (8.00 Inches) Comment: (Manual)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275 (Manual)
38	WASHER	12-36001

Exhaust Plate

Below is the parts list for Mercury 90 (3 CYL.) Exhaust Plate:

Position No.	Part Name	OEM Number	Supersedes
1	PLATE, Exhaust	881912T01
2	PIN, Dowel	17-23784
3	RETAINER	881973
4	MOUNT	881915002	881915001
5	SCREW, (M8 x 35 MM)	10-881975
6	BOLT, (M12 x 175)	10-898487	10-42974
7	NUT, (M12)	11-896963	11-859129, 11-90099
8	SPACER (Long)	23-813745	23-43041
8	SPACER (X-Long)	23-11289
9	COUPLING	43585
10	GASKET	27-430086
11	TUBE, Exhaust	42966T07
12	SCREW, (M8 x 35) Stainless Steel	10-40011151
13	SEAL	8M0039075	42962
14	GROMMET	25-89417004
15	TUBE, Water - Long (13.21 Inches)	32-8M0042791	32-881201 1
15	TUBE, Water (15.71 Inches) X Long (75/90)	32-8M0042793	32-881201 3
15	TUBE, Water - X Long (18.21 Inches)	32-8M0042792	32-881201 2
16	CLAMP	824661
17	SEAL, Upper	814080001	814080
18	SCREW, (M8 x 45)	10-889833045
19	CLAMP, Bracket, Upper Mount	881918T03	881918T02, 881918T
20	GROMMET	25-19565002
20	GROMMET (Manual Models)	25-8M0179867
21	BUSHING	23-48237
22	SHIFT SHAFT ASSEMBLY	79932A20
22	SHIFT SHAFT ASSEMBLY (Manual Models)	79932A23
23	SHIFT LINK	42912A3
24	BUSHING	23-48475
25	NUT, (M6) Stainless Steel	11-401386
26	SCREW, (M8 x 35) Stainless Steel	10-40011151
27	SCREW, (M8 x 70) Stainless Steel	10-40011158

Flywheel and Starter Motor

Below is the parts list for Mercury 90 (3 CYL.) Flywheel and Starter Motor:

Position No.	Part Name	OEM Number	Supersedes
1	PLUG, Yellow	19-45907
2	COVER ASSEMBLY	812777T1
3	NUT, (M16)	11-42979
4	WASHER, (.641 x 1.250 x .190)	12-33001
5	FLYWHEEL ASSEMBLY Comment: (Electric-Oil Injection)	261-878226T10	261-859234T12, 261-9008A58 (Electric-Oil Injection)
5	FLYWHEEL ASSEMBLY Comment: (Electric-Non Oil Injection)	261-878226T16	261-9008T84 (Electric-Non Oil Injection)
6	FLYWHEEL ASSEMBLY Comment: (Manual)	261-878226T8
7	STATOR ASSEMBLY Comment: (Electric)	398-832075A21	398-832075A 4 (Electric)
7	STATOR ASSEMBLY Comment: (Manual)	398-832074A11	398-832074A 5 (Manual)
-	CABLE ASSEMBLY Comment: (Electric)	84-11149A27
8	SCREW, (M5 x 30)	10-4013930
9	TRIGGER	854512T	834820T
10	TIE STRAP, (4.00 Inches)	56762
11	SWIVEL BASE	93254
12	SWIVEL BALL	93421
13	STARTER MOTOR ASSEMBLY	50-893891T	50-66015T 1
13	STARTER MOTOR ASSEMBLY	50-893891T	50-66015T 1
14	COLLAR	23-8M0034918	23-8M0001391, 56703
15	STOP	8M0043376	68042
16	CABLE ASSEMBLY, (6.00 Inches) Black	84-93388A1
17	SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel	10-69035
18	CABLE ASSEMBLY, (12.5 Inchs) Black	84-93388A8
19	LOCKWASHER, (.250) Stainless Steel	13-26992
20	NUT, (.250-20)	11-64015
21	DECAL, Warning, High Voltage Comment: (Electric)	37-8272822
22	PLUG, Male Comment: (Manual)	13541
23	DECAL, Caution-Start in Gear Comment: (Start In Gear) (Electric)	37-881865	37-825064 (Start In Gear) (Electric)

Fuel Pump

Below is the parts list for Mercury 90 (3 CYL.) Fuel Pump:

Position No.	Part Name	OEM Number	Supersedes
-	PUMP KIT, Fuel	14360A78
1	NOT SOLD SEPARATE, Fuel Pump	NSS
2	DIAPHRAGM KIT	21-857005A1
3	NOT SOLD SEPARATE, Check Valve	NSS
4	NOT SOLD SEPARATE, Retainer	NSS
5	NOT SOLD SEPARATE, Spring	NSS
6	NOT SOLD SEPARATE, Cap	NSS
7	NOT SOLD SEPARATE, Gasket-Boost	NSS
8	NOT SOLD SEPARATE, Cap	NSS
9	NOT SOLD SEPARATE, Spring	NSS
10	NOT SOLD SEPARATE, Gasket-Pulse	NSS
11	NOT SOLD SEPARATE, Diaphragm	NSS
12	GASKET	27-8M0204705
13	BASE	144303
14	PLATE	987752
15	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
16	SCREW, (M5 x 40)	10-82104540
17	SCREW, (M6 x 50)	10-82130050
18	TIE STRAP, (5.50 Inches)	8M0214940
19	Hose, Molded	32-897930
20	FITTING Comment: (To Crankcase)	22-291112
21	TUBING, (.312) (70.00 Inches Bulk) (Cut to 2.00 Inch Length) Comment: (Oil Injection)(To Carburetor)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80 (Oil Injection)(To Carburetor)
22	LINE ASSEMBLY, Fuel Comment: (Oil Injection)	32-19017A1
23	FILTER, Fuel Comment: (Oil Injection)	35-816296Q2
24	TUBING, (.312) (70.00 Inches Bulk) (Cut to 6.00 Inch Length) Comment: (Non Oil Injection)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80 (Non Oil Injection)
25	MOLDED HOSE Comment: (Oil Injection)	32-822554
26	PLUG, Non Commercial Engines Comment: (Oil Injection)	19-822772
27	CHECK VALVE (Oil Injection) Comment: (Oil Injection)(To Oil Pump)	22-8189941
28	CONNECTOR ASSEMBLY, Fuel Comment: (Design I)	22-816856Q3
29	O-RING, Fuel Connector Comment: (Design I)	25-16524
30	SCREW, (M6 x 35) Stainless Steel Comment: (Design I)	10-4010635
31	GROMMET Comment: (Design I)	25-145091
32	CONNECTOR Comment: (Design II)	22-822769
33	TUBING, (26.00 Inches Bulk) (Cut to 4.00 Inch Length) Comment: (Design II)	32-85682257
34	GROMMET Comment: (Design II)	25-145093
35	SOLENOID ASSEMBLY, Enrichner Valve Comment: (Electric)	89-819503A1
36	TUBING, (38.00 Inches Bulk) (Cut to 15.00 Inch Length) Comment: (Electric)	32-1430165
37	TUBING, (36.00 Inches Bulk) (Cut to 11.50 Inch Length) Comment: (Electric)	32-9912688
38	CLAMP Comment: (Electric)	54-188871
39	TUBING, (.312) (70.00 Inches Bulk) (Cut to 17.00 Inch Length) Comment: (Non Oil Injection)(To Carburetor)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80 (Non Oil Injection)(To Carburetor)
40	TUBING, (32.00 Inches Bulk) (Cut to 13.00 Inch Length) Comment: (Non Oil Injection)	32-83476463
41	INSULATING SLEEVE Comment: (Non Oil Injection)	23-83312531
42	FILTER, Fuel Comment: (Non Oil Injection)	35-826634T01	35-826634T, 35-826634 (Non Oil Injection)
43	BRACKET Comment: (Non Oil Injection)	827961
44	SCREW, (M6 x 14) Comment: (Non Oil Injection)	10-82129114
45	SCREW, (M6 x 30) Stainless Steel Comment: (Non Oil Injection)	10-4010630
46	WASHER Comment: (Non Oil Injection)	12-8M0214930
47	BUSHING Comment: (Non Oil Injection)	23-42116
48	GROMMET Comment: (Non Oil Injection)	25-42117
49	PRIMER BULB Comment: (Manual)	858763	816877 3 (Manual)
50	FITTING, Tee Comment: (Manual)	22-59169003
51	TUBING, (240.00 Inches Bulk) (Cut to 6.00 Inch Length) Comment: (Manual)	32-892024122	32-99130122 (Manual)
52	TUBING, (240.00 Inches Bulk) (Cut to 9.50 Inch Length) Comment: (Manual)	32-892024122	32-99130122 (Manual)
53	TUBING, (240.00 Inches Bulk) (Cut to 2.50 Inch Length) Comment: (Manual)(To Top Carburetor)	32-892024122	32-99130122 (Manual)(To Top Carburetor)
54	TUBING, (240.00 Inches Bulk) (Cut to 2.50 Inch Length) Comment: (Manual)	32-892024122	32-99130122 (Manual)
55	TUBING, (240.00 Inches Bulk) (Cut to 2.50 Inch Length) Comment: (Manual)(To Center Carburetor)	32-892024122	32-99130122 (Manual)(To Center Carburetor)
56	TUBING, (240.00 Inches Bulk) (Cut to 6.00 Inch Length) Comment: (Manual)(To Bottom Carburetor)	32-892024122	32-99130122 (Manual)(To Bottom Carburetor)
-	GASKET SET, Powerhead	27-43004A99

Gasket Set Components, Powerhead Overhaul

Below is the parts list for Mercury 90 (3 CYL.) Gasket Set Components, Powerhead Overhaul:

Position No.	Part Name	OEM Number	Supersedes
-	GASKET SET, Powerhead	27-43004A99
-	GASKET, Exhaust Manifold	27-43004009
-	O-RING (2.862)	25-89224
-	O-RING, (1.989 x .070) (1.989)	25-823683	25-64067
-	GASKET, Cylinder Block Cover	27-430057
-	GASKET, Thermostat	27-8M0204714
-	GASKET, Thermostat Cover	27-430068
-	NOT SOLD SEPARATE, Boost	NSS
-	NOT SOLD SEPARATE, Boost Chamber	NSS
-	NOT SOLD SEPARATE, Fuel Pump	NSS
-	NOT SOLD SEPARATE, Pluse Chamber	NSS
-	GASKET, Fuel Pump	27-8M0204705
-	GASKET, Reed Block/Crank	27-139376
-	O-RING (.739)	25-8M0204667
-	O-RING (1.362)	25-33466
-	SEAL, Water Tube, Upper	42941001
-	GROMMET, Water Tube	25-93221002
-	GASKET, Cylinder Block to Exhaust Plate	27-430075
-	PACKING	65800
-	NOT SOLD SEPARATE, Seal	NSS
-	O-RING, (3.609 x .139) (3.609)	25-8M0214974
-	GASKET, Aluminum Cover, Water Pump, Upper	27-430341
-	SEAL	12-191833
-	SEAL	19643
-	GASKET, Carburetor	27-151724
-	GASKET, Cover to Gearcase	27-8M0214931
-	GASKET, Water Pump, Upper	27-8172771
-	GASKET, Face Plate to Cover	27-430331
-	SPRING, Compression	24-42998
-	NOT SOLD SEPARATE, Spring End	NSS
-	NOT SOLD SEPARATE, Spring End	NSS
-	NOT SOLD SEPARATE, Check Valve	NSS
-	RETAINER, Check Valve	21-17311
-	NOT SOLD SEPARATE, Compression, Boost	NSS
-	NOT SOLD SEPARATE, Spring End	NSS
-	GASKET, Exhaust Plate/Exhaust Tube	27-430086
-	O-RING (2.112)	25-858225

Gear Housing(Driveshaft 2.31:1)

Below is the parts list for Mercury 90 (3 CYL.) Gear Housing(Driveshaft 2.31:1):

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Complete Comment: (L=20 Inch Model)	1667-9011J15
-	GEAR HOUSING ASSEMBLY, Complete Comment: (LL=22.5 Inch Model)	1667-9011J21
-	GEAR HOUSING ASSEMBLY, Complete Comment: (XL=25 Inch Model)	1667-9011J23
1	GEAR HOUSING ASSEMBLY, Basic, Torpedo Diameter - 4.25 Inch / 107.95 mm	1667-9011G59
2	PIN, Dowel - With Hole (.375 x .625) , Front	17-8M0084244	17-43043
3	TUBE, Oiler	43046
4	SCREW KIT, (.375-16 x .250) Drain	10-79953Q04
4	FITTING KIT, Magnetic, Plug Fill/Drain Comment: (Magnetic)	22-8M0058389	22-67892A06 (Magnetic)
5	WASHER	12-191833
6	PIN, Dowel - Without Hole (.375 x .625), Rear	17-43044
7	TRIM TAB	31640T07
8	SCREW, (.437-14 x 1.250) Stainless Steel	10-825427	10-15942
9	WASHER, (.453 x .812 x .105) Black Oxide	12-451761
10	CARRIER ASSEMBLY	43040T1
11	NOT SOLD SEPARATE, Needle Bearing	NSS
12	ANODE	97-826134Q	826134, 826134A 1
13	NUT, (M6) Stainless Steel	11-401386
14	SCREW, (M6 x 40)	10-4000333
15	NOT SOLD SEPARATE, Pinion Gear (12 Teeth) Comment: (Part of 43-882813A 3)	NSS
16	NUT, (.625-18)	11-35921
17	CAM, Shift Control	850307
18	BEARING ASSEMBLY, Tapered Roller	31-883047A1
19	SHIM SET	15-44492A1
20	DRIVESHAFT ASSEMBLY Comment: (L -32 Inch)	45-43031A1
20	DRIVESHAFT ASSEMBLY Comment: (LL -34.50 Inch)	45-43032A6
20	DRIVESHAFT ASSEMBLY Comment: (XL -36.915 Inch)	45-43032A4
21	SLEEVE/RING KIT	42461A1
22	NOT SOLD SEPARATE, Seal Ring	NSS
23	COVER ASSEMBLY, Water Pump	43055A4
24	GASKET	27-430331
25	GASKET	27-8M0214931
26	SEAL, Oil, Lower	26-43036
27	SEAL, Oil, Upper	26-43035
28	GASKET	27-8172771
29	HOUSING KIT, Upper Water Pump	817275A2
30	FACEPLATE	8M0204709
31	SCREW, (M6 x 30)	10-82684430
32	SEAL	430232
33	KEY	28-8M0204723
34	IMPELLER	47-43026T2
35	SCREW, (M6 x 25)	10-82684425
36	SHIFT SHAFT ASSEMBLY Comment: (L-12 Inch)	853906A1
36	SHIFT SHAFT ASSEMBLY Comment: (LL-14.50 Inch)	853907A1
36	SHIFT SHAFT ASSEMBLY Comment: (XL-17 Inch)	853908A1
37	E RING	53-29641
38	BUSHING ASSEMBLY	23-43052A4
39	O-RING, (1.424 x .103)	25-8M0204681
40	SEAL, Oil	26-8M0204708
41	SCREW, (M6 x 25)	10-82684425
42	FACE SEAL	26-861415	26-816575
-	SEAL KIT, Gear Housing	26-43035A4
-	REPAIR KIT, Water Pump	46-8M0113799
-	GASKET SET	27-13461A99
-	REPAIR KIT, Water Pump Impeller	47-8M0100526	47-43026Q06

Gear Housing, Propeller Shaft - 2.31:1 Gear Ratio

Below is the parts list for Mercury 90 (3 CYL.) Gear Housing, Propeller Shaft - 2.31:1 Gear Ratio:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Complete Comment: (L=20 Inch Model)	1667-9011J15
-	GEAR HOUSING ASSEMBLY, Complete Comment: (LL=22.5 Inch Model)	1667-9011J21
-	GEAR HOUSING ASSEMBLY, Complete Comment: (XL=25 Inch Model)	1667-9011J23
1	GEAR HOUSING ASSEMBLY, Basic, Torpedo Diameter - 4.25 Inch / 107.95 mm	1667-9011G59
2	BEARING SET, Cup And Cone	31-30894A1
3	NOT SOLD SEPARATE, Cup	NSS
4	GEAR KIT, Forward And Pinion 28 Teeth	43-882813A3
5	BEARING, Needle	31-30895T
6	RING, Retaining	53-856823
7	FOLLOWER KIT, Cam	850315A1
8	BALL	30-44530
9	NOT SOLD SEPARATE, Slide	NSS
10	SPRING	24-850327
11	PIN, Cross	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
12	SPRING	24-30893
13	CLUTCH	52-850048T	52-850048
14	PROPELLER SHAFT	44-8M0140445
15	GEAR, Reverse - 28 Teeth	43-882814T
16	CARRIER ASSEMBLY, Bearing	8M0168901
17	O-RING, (3.609 x .139)	25-8M0214974
18	BEARING, Needle	31-30956T
19	SEAL, Oil, Inner	26-8M0205728
20	SEAL, Oil, Outer	26-8M0205729
21	BEARING, Roller	31-12578T
22	THRUST WASHER	12-12577
23	BEARING, Thrust	31-12576
24	STUD, (M8 x 48)	16-8M0034456	16-42917 2
25	WASHER, (.323 x .590 x .112) Stainless Steel	12-855941
26	NUT, (M8)	11-401378
27	SHIM SET	15-44491A1
28	INSERT, Threaded	8227731
29	NOT SOLD SEPARATE, Decal-Pinion Indentification	NSS
-	SEAL KIT, Gear Housing	26-43035A4
-	GASKET SET	27-13461A99

Induction Manifold and Reed Block

Below is the parts list for Mercury 90 (3 CYL.) Induction Manifold and Reed Block:

Position No.	Part Name	OEM Number	Supersedes
1	COVER/PLATE KIT, Exhaust	42878A2
2	NOT SOLD SEPARATE, Baffle Plate	NSS
3	GASKET	27-43004009
4	SCREW, (M8 x 35 MM)	10-82127335
5	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
6	GASKET	27-430075
7	SHIFT RAIL ASSEMBLY	42881A1
8	TAB WASHER	14-42981
9	SCREW, (M8 x 25)	10-40001134
10	SLIDE	988851
11	NUT, (M6) Stainless Steel	11-401386
12	WASHER	12-35459
13	NUT, (M6) Stainless Steel	11-401386
14	CAP ASSEMBLY, Lower End	1169-858552T2
15	CHECK VALVE	21-426585
16	SEAL, Oil	26-419533
17	O-RING	25-89224
18	SCREW, (M10 x 25) Hex Flange - Stainless Steel	10-4010825
19	REED BLOCK ASSEMBLY	8M0219198
20	NOT SOLD SEPARATE, Dowel Pin	NSS
21	GASKET	27-139376
22	REED SET	34-43018A1
23	TAB WASHER	14-429821
24	RETAINER	42924
25	SCREW, (M6 x 16)	10-88421471
26	BRACKET Comment: (Non Oil Injection)	8M0039350	821944 1 (Non Oil Injection)
26	BRACKET Comment: (Oil Injection)	827514
27	WASHER, (.187 x .500 x .062) Neoprene	12-8M0204663
28	WING NUT	11-816872
29	STUD, (M6 x 44)	16-8161949
30	MANIFOLD, Induction	884296T	42967 2
31	SCREW, (M8 x 35 MM)	10-82127335
32	SCREW, (M8 x 40)	10-81742740
33	STUD, (M8 x 1.25)	16-824470	16-42985, 16-42985 1
34	SCREW, (M8 x 110) (#3 CYLINDER)	10-40001167
35	TUBING, (.312) (70.00 Inches Bulk) (Cut to 4.00 Inch Length)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
36	TEE FITTING Comment: (Electric)	22-432881
36	CONNECTOR Comment: (Manual)	22-8585531
37	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
38	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
39	DECAL, EPA Label Information (2005)	37-804666A05
39	DECAL, EPA Label Information (2006)	37-804666A06
39	DECAL, EPA Label Information (2007)	37-804666A07
39	DECAL, EPA Label Information(2008)	37-804666A08
39	NOT SOLD SEPARATE, DECAL, EPA (2009 & Up) Comment: (Contact Mercury Marine Warranty Administration for Replacement-Service Bulletin 2009-18)	NSS
-	GASKET SET, Powerhead	27-43004A99
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection)	898208A02	855530T98, 855530A98 (Non Oil Injection)
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 1B227000 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 1B227000 & Up
-	POWERHEAD ASSEMBLY Comment: (Non Oil Injection) SN# 0P401000 & Up	898208A02	855530T98, 855530A98 (Non Oil Injection) SN# 0P401000 & Up
-	POWERHEAD ASSEMBLY Comment: (Oil Injection)	809837T97	809837A97, 809837A96, 15081A95, 809837A98 (Oil Injection)

Jet Pump Assembly

Below is the parts list for Mercury 90 (3 CYL.) Jet Pump Assembly:

Position No.	Part Name	OEM Number	Supersedes
-	JET PUMP ASSEMBLY	856143A1
1	HOUSING, Pump	855767T90	855767 90
2	SHIFT LINKAGE KIT	878377
3	CAM	878382
4	GATE, Reverse - With Bumper	878380
5	HOSE, Lube	32-827490
6	SCREW, (.312-18 x 1.00)	10-848497
7	STUD, (.312-18 x 1.81)	16-855840
8	NUT, (.312-18) Stainless Steel	11-82670910
9	IMPELLER	47-855708115	47-801414 90, 47-801414115
10	HOUSING, Intake	85576890
11	LINER	855771
12	DRIVESHAFT	45-85576990
13	THRUST WASHER	12-8796522
14	BEARING, Ball	30-8796531
15	SLEEVE	23-8271891
16	NUT	11-8271901
17	ADAPTOR, Pump	808747
18	WASHER	12-36001
19	KEY	28-801405875
20	SHIM, Impeller	15-801404875
21	TAB WASHER	14-801403875
22	PIN, Dowel	17-801407
23	SCREW, (.250-20 x .625)	10-19923062
24	SCREW, (.312-18 x 1.250)	10-60411
25	BRACKET, Cable Support	801410
26	NUT, (.312-18)	11-82670910
27	SCREW, (M10 x 60) Hex Flange - Stainless Steel	10-4010860
28	SCREW, (M10 x 90) Hex Flange - Stainless Steel	10-4010890
29	SCREW, (M10 x 70) Hex Flange - Stainless Steel	10-4010870
30	SCREW, (.375-16 x 4.00) Stainless Steel	10-843575
31	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963

Jet Pump Componets

Below is the parts list for Mercury 90 (3 CYL.) Jet Pump Componets:

Position No.	Part Name	OEM Number	Supersedes
1	HOUSING KIT, Upper Water Pump	817275A2
2	GASKET	27-8172771
3	FACEPLATE	8M0204709
4	SCREW, (M6 x 30)	10-82684430
5	SEAL	430232
6	KEY	28-8M0204723
7	IMPELLER	47-43026T2
8	REV LIMITER	821889A50	821889A42
9	SCREW, (M6 x 30)	10-82130030
-	SEAL KIT, Gear Housing	26-43035A4
-	REPAIR KIT, Water Pump	46-8M0113799
-	GASKET SET, Powerhead	27-43004A99

Key Chart

Below is the parts list for Mercury 90 (3 CYL.) Key Chart:

Position No.	Part Name	OEM Number
-	KEY, Ignition (1A)	894911
-	KEY, Ignition (1B)	894912
-	KEY, Ignition (1C)	894913
-	KEY, Ignition (1D)	894914
-	KEY, Ignition (1E)	894915
-	KEY, Ignition (1F)	894916
-	KEY, Ignition (2A)	894917
-	KEY, Ignition (2B)	894918
-	KEY, Ignition (2C)	894919
-	KEY, Ignition (2D)	8949110
-	KEY, Ignition (2E)	8949111
-	KEY, Ignition (2F)	8949112

Lube Chart

Below is the parts list for Mercury 90 (3 CYL.) Lube Chart:

Position No.	Part Name	OEM Number	Supersedes
	NO PARTS LIST	NOPART

Manual Tilt Assist Components

Below is the parts list for Mercury 90 (3 CYL.) Manual Tilt Assist Components:

Position No.	Part Name	OEM Number	Supersedes
-	MANUAL TILT ASSEMBLY	835249T1
1	SHOCK ROD ASSEMBLY	893932A01	853891A 1
2	O-RING KIT, Cylinder	25-893917A01	25-809872A 1
3	PISTON ASSEMBLY, Trim Memory	893903A01
4	CYLINDER ASSEMBLY	893934A01	835250A 1
5	SCREW AND SEAL KIT	893919A01	813433A 2
6	ACCUMULATOR ASSEMBLY	893933A01	835458A 1
7	VALVE BODY ASSEMBLY	893921A01	813455T 4
8	CAM KIT	893923A01	813457A 3
9	VALVE KIT, Velocity	893924A01	809881A 1
10	REPAIR KIT	893925A01	809882A 1
-	O-RING KIT	25-893922A01	25-809880A 2

Oil Injection Components

Below is the parts list for Mercury 90 (3 CYL.) Oil Injection Components:

Position No.	Part Name	OEM Number	Supersedes
1	TANK ASSEMBLY, Oil	1277-8M0219216
2	CAP	828475A1
3	O-RING	25-26318T
4	DIPSTICK	828793
5	NUT	11-65110
6	VENT ASSEMBLY	19299A1
7	VALVE	21-64871
8	BRACKET	8287201
9	BOOT	99160001
10	SCREW, (M6 x 20) Stainless Steel	10-4010620
11	GROMMET	25-825380001	25-825380
12	BUSHING	23-828350
13	WASHER	12-4002318
14	SCREW, (M8 x 35)	10-81893435
15	SWITCH ASSEMBLY	87-12886A6
16	SCREW, (.164-18 x .375)	10-58376
17	WASHER, (.203 x .562 x .060) Stainless Steel	12-72761
18	GEAR, Driven	43-430204
19	O-RING	25-8M0204667
20	ADAPTOR ASSEMBLY	17335A3
21	BUSHING	23-17597
22	BUSHING	23-17596
23	PUMP ASSEMBLY, Oil	42959A2
24	SCREW, (M5 x 40)	10-82104540
25	TUBING, (15.00 Inches Bulk) (Cut to 6.00 Inch Length) Comment: A=To Fuel Pump	32-82381335
26	TUBING, (25.00 Inches Bulk) (Cut to 11.00 Inch Length)	32-82381455
27	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
27	TIE STRAP, (5.50 Inches)	8M0214940
-	GASKET SET, Powerhead	27-43004A99

Power Trim Assembly - Components, 2B092563 and Up

Below is the parts list for Mercury 90 (3 CYL.) Power Trim Assembly - Components, 2B092563 and Up:

Position No.	Part Name	OEM Number	Supersedes
1	MANIFOLD KIT	8M0089943
2	VALVE KIT, Relief	893929A01	813442A 2
3	VALVE KIT	8M0089945
4	VALVE KIT - (TRIM LIMIT)	8M0090404	8M0058589
5	O-RING	833063
6	DOWEL PINS	8M0055260
7	PLUG ASSEMBLY	19-811613
8	SCREW, (.250-20 x 2.250)	10-833047
9	CYLINDER ASSEMBLY	8M0089941
10	CABLE ASSEMBLY	8M0207768
11	SCREW	8M6002690
12	PISTON ASSEMBLY, Memory	8M0171822
13	O-RING KIT	25-8M0171819
14	SHOCK ROD KIT	8M0171821
15	SCREW KIT (COMPLETE TRIM)	10-8M0089946
16	MOTOR KIT	8M0142591
17	COUPLING / DRIVESHAFT KIT	8M0090403	878245 1
18	PUMP ASSEMBLY	8M0089944
-	O-RING KIT, Power Trim	25-8M0171820

Power Trim Assembly, 2B092563 and Up

Below is the parts list for Mercury 90 (3 CYL.) Power Trim Assembly, 2B092563 and Up:

Position No.	Part Name	OEM Number	Supersedes
1	POWER TRIM ASSEMBLY	8M0171818
2	PIN, Shock Rod	17-8M0161312
3	PIN, Trilobe	17-821539	17-13794, 17-19603
4	PIN, Anchor	17-818898
5	HARNESS ASSEMBLY, Trim	84-8M0092077
6	RELAY ASSEMBLY	8M0207773
7	BRACKET	828102
8	BUSHING	23-8M0214955
9	GROMMET	25-818967
10	SCREW, (M6 x 25 MM)	10-82129125

Power Trim Components, 2B092562 and Below

Below is the parts list for Mercury 90 (3 CYL.) Power Trim Components, 2B092562 and Below:

Position No.	Part Name	OEM Number	Supersedes
-	PUMP ASSEMBLY, Power Trim	8M0171818
-	PUMP ASSEMBLY, Power Trim	8M0171818
1	SHOCK ROD KIT	8M0171821
2	O-RING KIT, Rebuild	25-8M0171819
3	PISTON ASSEMBLY, Memory	8M0171822
4	CYLINDER ASSEMBLY	893916A01	811669A 1
5	VALVE KIT, Trim Limit	893905A02	809873A 1
6	PUMP ASSEMBLY	893906A02	809874A 1
7	MOTOR KIT	893907A02	809885A 2
8	PLUG	22-8134351
9	MANUAL RELEASE ASSEMBLY	893929A01	813442A 2
10	MANIFOLD KIT	893909A02	809875A 1
11	SCREW KIT, Motor	10-809876A1
12	CABLE ASSEMBLY	88238A18
13	DRIVESHAFT/SEAL KIT	809877A1
14	FILTER KIT	35-893912A02	809878A 1
15	POPPET KIT	893913A02	809879A 1
-	O-RING KIT (COMPLETE TRIM)	25-893914A02	25-809880A 1
16	RELAY ASSEMBLY	8M0207773
17	BUSHING	23-8M0214955
18	GROMMET	25-818967
19	BRACKET	828102
20	NOT SOLD SEPARATE, Decal, Trim Relay	NSS
21	HARNESS ASSEMBLY, Trim	84-8M0092077
22	SCREW, (M6 x 25 MM)	10-82129125
23	CLIP	54-22740
24	SCREW, (#10-16 x .600)	10-878609	10-812832 1
25	C WASHER	8M0084613	69205

Service/Support Material

Below is the parts list for Mercury 90 (3 CYL.) Service/Support Material:

Position No.	Part Name	OEM Number	Supersedes
-	PARTS MANUAL, 75/90 Hp 65 Jet (3 Cylinder)	90-803147001
-	OWNERS MANUAL, SeaPro/Marathon (2005)	90-10182050
-	OWNERS MANUAL, (Manual 75-SeaPro/Marathon) (2006)	90-10182060
-	OWNERS MANUAL, (2005), English	90-10180050
-	OWNERS MANUAL, (75/90/115/125)(2-Stroke) (2006) English	90-10180080
-	OWNERS MANUAL, (2005), Spanish	90-10180J50
-	OWNERS MANUAL, (75/90/115/125)(2-Stroke) (2006) Spanish	90-10180J60
-	OWNERS MANUAL, (2005), French	90-10180D50
-	OWNERS MANUAL, (75/90/115/125)(2-Stroke) (2006) French	90-10180D60
-	OWNERS MANUAL, Jet 65/80 (2005) English	90-10138050
-	OWNERS MANUAL, Jet 65/80 (2005) Spanish	90-10138J50
-	OWNERS MANUAL, Jet 65/80 (2005) French	90-10138D50
-	SERVICE MANUAL	90-8M0127990
-	DECAL SET (Black 75 Electric) Comment: (2005)	37-808549A00	37-808549A96, 37-808549A94 (2005)
-	DECAL SET, (Black 75) Comment: (2006 - 2B111024)	37-897514A01
-	DECAL SET, 50-90 Comment: 2B111248 and up)	37-8M0094902
-	DECAL SET (75 Electric SeaPro) Comment: (2005 and Up)	37-826315A01	37-826315A95, 37-823414A94, 37-823414A93 (2005 and Up)
-	DECAL SET (75 Manual SeaPro) Comment: (2005 and Up)	37-826317A01	37-826317A95, 37-823415A94, 37-823415A93 (2005 and Up)
-	DECAL SET (Black 90) Comment: (2005)	37-823417A00	37-823417A96, 37-823417A94 (2005)
-	DECAL SET, (Black 90) Comment: (2006 - 2B111247)	37-897514A02
-	DECAL SET (Black 90 Saltwater) Comment: (2005)	37-856795A00	37-856795A99 (2005)
-	DECAL SET (Black 65 Jet) Comment: (2005)	37-826327A00	37-826327A96, 37-826327A95 (2005)
-	DECAL SET, (65 Jet) Comment: (2006 and Up)	37-897514A03
-	DECAL, Gray (International Only) Comment: (75 Electric-Mariner)(Front/Rear)(2005 and Up)	37-8588381
-	DECAL, Gray (International Only) Comment: (75 Electric Mariner)(Port/Starboard)(2005 and Up)	37-8588382
-	DECAL, Gray - Front/Rear - 75 Manual - Mariner Comment: (2005 and Up)	37-8588391
-	DECAL, Gray - Port/Starboard - 75 Manual - Mariner Comment: (2005 and Up)	37-8588392
-	DECAL SET (75 Electric-Gray) Comment: (2005 and Up)	37-826318A03	37-826318A00, 37-826318A95, 37-823423A94, 37-823423A93 (2005 and Up)
-	DECAL SET (90 Electric-Gray) Comment: (2005 and Up)	37-823420A03	37-823420A01, 37-823420A97, 37-823420A94, 37-830166A99 (2005 and Up)
-	DECAL SET (Tracker 75) Comment: (2005)	37-808622A96
-	DECAL SET (Tracker 90) Comment: (2005)	37-808571A96
-	HOSE ASSEMBLY, Fuel	32-858610A31	32-858610A10, 32-16789A18
-	DECAL, EPA Label Information (2005)	37-804666A05
-	DECAL, EPA Label Information (2006)	37-804666A06
-	DECAL, EPA Label Information (2007)	37-804666A07
-	DECAL, EPA Label Information(2008)	37-804666A08
-	NOT SOLD SEPARATE, DECAL, EPA (2009 & Up) Comment: (Contact Mercury Marine Warranty Administration for Replacement-Service Bulletin 2009-18)	NSS

Starter Assembly(Manual)

Below is the parts list for Mercury 90 (3 CYL.) Starter Assembly(Manual):

Position No.	Part Name	OEM Number	Supersedes
1	HANDLE ASSEMBLY	85174A2
2	NOT SOLD SEPARATE, Retainer	NSS
3	REST	8220721
4	SEAL	8M0043270	823241
5	SCREW, (M6 x 50)	10-82130050
6	SPACER	23-8217021
7	BUSHING	23-816086
8	GROMMET	25-815795
9	WASHER, (.281 x .734 x .063) Comment: (Quantity of 2 used in Front. Quantity of 4 used in Back)	12-69057
10	BRACKET	855596
11	BRACKET	855597
12	SCREW, (M6 x 25) Stainless Steel	10-40011129
13	WASHER, (.2656 x .625 x .0625) Stainless Steel	12-35462
14	NUT, (M6) Stainless Steel	11-401386
15	PULLEY KIT	11704A1
16	NOT SOLD SEPARATE, Spacer	NSS
17	WASHER	12-67983
18	CABLE, Interlock	8567541
19	SCREW, (#10-16 x .625)	10-8214281
20	WASHER, (.220 x .500 x .030) Stainless Steel	12-73288
21	COTTER PIN	18-26811
22	SCREW, (#10-16 x .500)	10-878608	10-812832
23	WASHER, (.2656 x .625 x .0625) Stainless Steel	12-35462
24	COTTER PIN	18-26811
-	STARTER ASSEMBLY, Recoil	816728T14	816728A14, 816728A12, 816728A11, 816728A10, 816728A 9
25	SPRING	24-826791	24-816718 1
26	LEVER	8166903
27	CAM	816712T01	816712 1
28	RETAINER	816711
29	SCREW, (#10-16 x 1.00)	10-8182491
30	LOCKWASHER	13-826229
31	SPRING	24-86857T01
32	SHEAVE, Starter	50-825269T01	50-825269A 1
33	SPRING	24-86851T02
34	CAM	868501
35	RING, Retaining	53-86849T01
36	ROPE	50-12066Q10
37	HOUSING	816728T05	816728 5
38	SPRING	24-868523
39	CAM	86853T01
40	SCREW, (.250-20 x .625)	10-826253	10-97516, 10-818838
41	BUSHING	8M0183792
42	RING, Retaining	53-818853	53-42689
43	NOT SOLD SEPARATE, Decal-Manual Start	NSS

Starter Motor, Service

Below is the parts list for Mercury 90 (3 CYL.) Starter Motor, Service:

Position No.	Part Name	OEM Number	Supersedes
-	STARTER MOTOR ASSEMBLY	50-893891T	50-66015T 1
-	STARTER MOTOR ASSEMBLY	50-893891T	50-66015T 1
1	DRIVE KIT	90643
2	DRIVE ASSEMBLY	685753
3	PLATE	75660
4	BOLT	10-75385
5	ARMATURE	75386
6	BRUSH/SPRING KIT	898265016	75384, 75384 1
7	BUSHING	23-57387
8	NOT SOLD SEPARATE, Washer (AMER. BOSCH #WA-1728)	NSS
9	LOCKWASHER, (.250) Stainless Steel	13-26992
10	NUT, (.250-20)	11-20890
11	HOLDER	898265014	61787
12	NOT SOLD SEPARATE (AMER. BOSCH #02441-22-SC-30SM DRIVE TIGHT	NSS
13	END CAP	15386001

Steering Handle

Below is the parts list for Mercury 90 (3 CYL.) Steering Handle:

Position No.	Part Name	OEM Number	Supersedes
1	HANDLE ASSEMBLY, Steering Arm	12020A3
NS	FITTING, Grease	22-8M0169589
2	BUSHING	23-42992T02
3	HOUSING	48414
4	PLATE	48519
5	GASKET	27-48518
6	SCREW, (#10-16 x .600)	10-878609	10-812832 1
7	SCREW, (#10-16 x .500)	10-878608	10-812832
8	CLAMP	54-889729	54-12013
9	SCREW, (M5 x 40)	10-40007112
10	WING NUT,	10-32,11-816874	11-73651, 11-816873, 11-90052
11	HANDLE, Throttle (#96495 6)
12	SWITCH KIT, Stop - Throttle Handle	87-823609A15	87-15823A 6, 96495A 3, 87-15823A 5
13	SWITCH ASSEMBLY, Stop	87-8M0104612	87-823609A 5
14	TUBE ASSEMBLY, Throttle	12018A4
15	NOT SOLD SEPARATE, Drive Wheel	NSS
16	NOT SOLD SEPARATE, Roll Pin	NSS
17	SCREW, (#10-16 x .375)	10-62568
18	GRIP	8M0221732
19	CLAMP	54-648551
20	NUT, (M10)	11-40140
21	CONDUIT	8885242
22	GUIDE TUBE	8M0026078	89566 1
23	BARREL	89578
24	SET SCREW,	10-32,10-824081	10-89601
25	CABLE ASSEMBLY	12019
26	GUIDE	8M0204660
27	ANCHOR	20007
28	SET SCREW,	8-32,10-8M0204644
29	SCREW, (M10 x 105) Hex Flange - Stainless Steel	10-823567105	10-817430105
30	CAP	48416
31	WASHER	12-4002319
32	WASHER, (.402 x .787 x .039 Bellevi)	12-12024
33	SPACER	23-146011
34	WASHER, (.406 x .750 x .105) Stainless Steel Comment: (Use Where Applicable)	12-8M0214963
35	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
36	NOT SOLD SEPARATE, Decal-Throttle	NSS

Steering Handle Components

Below is the parts list for Mercury 90 (3 CYL.) Steering Handle Components:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET ASSEMBLY	12022A22
2	SCREW, (.375-24 x 1.250)	10-849838	10-14000
3	NUT, (.375-24) Stainless Steel	11-8M0204726
4	STUD, (.3125 x 2.50)	16-8M0034421	16-822320
5	SPACER	822263
6	WASHER, (.344 x .688 x .065) Stainless Steel	12-8M0204690
7	NUT, (.312-24) Stainless Steel	11-82670911
8	GROMMET	121051
9	HARNESS ASSEMBLY Comment: (Electric)	84-12649A5
10	SWITCH KIT, Key Comment: (Reference Key Chart Section for Key)(Electric)	87-88107A5
11	NUT, Special - Black Nylon Comment: (Black Nylon) (Electric)	11-879755	11-93543 (Black Nylon) (Electric)
12	PLUG, Male Comment: (Electric)	13541
13	COVER	12015A1
14	SCREW, (#10-16 x .500)	10-878608	10-812832
15	PLUG Comment: (Manual Tilt Assist)	19-889730	19-12014 (Manual Tilt Assist)
16	SWITCH ASSEMBLY, Stop	87-11083A4
17	LANYARD ASSEMBLY	15920Q54
18	RETAINER, Brass	8M0032846	12044 1
19	SCREW, (M8 x 50)	10-4000358
20	TAB WASHER	14-42981
21	BUSHING	23-889732	23-42992 1
22	LEVER ASSEMBLY, Shift	12021A1
23	WASHER	12-815351
24	STUD, (.375-24 x 1.125)	16-8M0034452	16-58152
25	KNOB	98530
26	SHIFT ROD	495636
27	ROD END	48419T
28	BUSHING	23-26856
29	WASHER, (.273 x .437 x .031) Stainless Steel	12-35950
30	COTTER PIN	18-25191
31	DETENT/SPRING KIT	12016A2
32	NOT SOLD SEPARATE, Spring	NSS
33	TRIM SWITCH Comment: (Power Trim)	87-14645A4
34	NUT, (.468-32) Comment: (Power Trim)	49440
35	NOT SOLD SEPARATE, Decal Comment: (Power Trim)	NSS
36	HARNESS ASSEMBLY, Stop Comment: (Manual Tilt Assist)	84-815851A2
37	CABLE ASSEMBLY Comment: (Manual Tilt Assist)	84-821028A2
38	PLUG Comment: (Manual Tilt Assist)	815803
39	HORN ASSEMBLY	816051A2
40	CABLE ASSEMBLY	84-11149A3
41	CABLE ASSEMBLY Comment: (Electric)	84-86324A2
42	BRACKET	824930T2
43	SWITCH	87-8M0052927	87-813960A 3
44	SCREW, (M3 x 20)	10-88075020
45	PLATE	824923
46	HARNESS ASSEMBLY	84-824934A3
47	NOT SOLD SEPARATE, Decal-Shift	NSS

Swivel Bracket and Steering Arm

Below is the parts list for Mercury 90 (3 CYL.) Swivel Bracket and Steering Arm:

Position No.	Part Name	OEM Number	Supersedes
1	SWIVEL BRACKET	1400-8M0220957
2	SEAL, Oil, Lower	26-87735
3	BUSHING	23-818764	23-67669
4	O-RING	25-8M0214926
5	SPACER	23-816039
6	FITTING, Grease	22-8M0169589
7	BUSHING	23-821207	23-99608
8	SCREW, (.250-28 x .500)	10-64014
9	THRUST WASHER	12-816432
10	SWIVEL PIN ASSEMBLY	99661A35
11	LINK ROD ASSEMBLY	92876A12
12	SCREW, (.375-24 x 1.250)	10-849838	10-14000
13	NUT, (.375-24) Brass	11-8M0204726
14	WASHER, (.390 x .625 x .062) Stainless Steel	12-37828
15	NUT, (.375-24) Stainless Steel	11-8M0204726
16	BUMPER	8M0000519	881974
17	YOKE, Bottom	881914T01
18	RING, Retaining	53-67684
19	BUMPER, Bottom Yoke (X-Long)	11288001

Throttle Lever and Linkage

Below is the parts list for Mercury 90 (3 CYL.) Throttle Lever and Linkage:

Position No.	Part Name	OEM Number	Supersedes
1	LEVER, Throttle	42946T1
2	SCREW, (M5 x 35)	10-827008
3	CAP	826264
4	SPRING	24-826382
5	LEVER, Spark Advance	429471
6	SCREW, Adjusting (M6 x 55)	10-814776	10-42978
7	NUT, (M6) Stainless Steel	11-400212
8	CAP	42942
9	SWIVEL BASE	93254
10	SWIVEL BALL	93421
11	ROD, Spark Advance	878172	42918
12	BUSHING	23-812930A1
13	NOT SOLD SEPARATE, Insert	NSS
14	SCREW, (M10 x 45)	10-4007180
15	WASHER	12-42980
16	SPRING	24-55162
17	INSERT	42927
18	WASHER	12-35459
19	NUT, (M6) Stainless Steel	11-401386
20	ROD, Throttle	878420T	878420, 42919
21	BUSHING	23-8M0215006
22	CAM ASSEMBLY, Throttle	42948A7
23	STUD, (M6 x 44)	16-8161949
24	SPRING	24-14159
25	WASHER, (.255 x .620 x .030) Stainless Steel	12-69056
26	NUT, (M6) Stainless Steel	11-401386
27	NOT SOLD SEPARATE (Decal-Idle Screw-Arrow up)	NSS

Tiller Handle Adaptor Kit(Jet 65)

Below is the parts list for Mercury 90 (3 CYL.) Tiller Handle Adaptor Kit(Jet 65):

Position No.	Part Name	OEM Number	Supersedes
-	TILLER HANDLE ADAPTOR KIT	850000A3
1	CABLE ASSEMBLY, Shift	832001A6
2	NUT, (M6) Stainless Steel	11-401386
3	SLIDE	988851
4	BRACKET	828095
5	BRACKET	824930T2
6	CLIP	54-8054441
7	SCREW, (M6 x 13) Stainless Steel	10-40011126
8	BLOCK, Shift Cable-Retaining	828096
9	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
10	SCREW, (.250-28 x 1.75)	10-71958
11	LOCKWASHER, (.250) Stainless Steel	13-26992
12	BLOCK, Shift Cable-Retaining	828094
13	SET SCREW, (#10-32 x .310)	10-72734
14	WASHER	12-35459
15	NUT, (.250-28) Stainless Steel	11-35888
16	SWITCH	87-8M0052927	87-813960A 3
17	SCREW, (M3 x 20)	10-88075020
18	PLATE	824923
19	CABLE ASSEMBLY	84-824934A1

Tools, SPECIAL

Below is the parts list for Mercury 90 (3 CYL.) Tools, SPECIAL:

Position No.	Part Name	OEM Number	Supersedes
-	TOOL BAG Comment: (SeaPro/Marathon)	56-817383A1
-	FLYWHEEL HOLDER TOOL, Teeth Type Comment: (Electrical/Ignition)	91-52344
-	PULLER ASSEMBLY Comment: (Electrical/Ignition)	91-849154T1
-	MULTI METER Comment: (Electrical/Ignition)	91-99750A1
-	SWITCH ASSEMBLY Comment: (Electrical/Ignition)	91-52024A1
-	SERVICE TACHOMETER Comment: (Electrical/Ignition)	91-59339
-	AIR GAP TOOL, Eight Chamber Comment: (Electrical/Ignition)	91-830230T
-	GAP TOOL, Single Chamber Comment: (Electrical/Ignition)	91-63998A1
-	TESTER Comment: (Electrical/Ignition)	91-850439T1
-	TIMING LIGHT Comment: (Electrical/Ignition)	91-99379
-	HARNESS ASSEMBLY Comment: (Electrical/Ignition)	84-825207A2
-	ALIGNMENT TOOL Comment: (Trim/Tilt System)	91-112301
-	NOT SOLD SEPARATE (SNAP ON - CG41-14) Comment: (Trim/Tilt System)	NSS
-	NOT SOLD SEPARATE (SNAP ON - CG41-11) Comment: (Trim/Tilt System)	NSS
-	DOWN PRESSURE KIT Comment: (Trim/Tilt System)	91-822778A3
-	SPANNER WRENCH Comment: (Trim/Tilt System)	91-74951
-	HEAT LAMP Comment: (Trim/Tilt System)	91-63209
-	GAUGE TOOL Comment: (Powerhead)	91-29287
-	FLYWHEEL HOLDER TOOL, Teeth Type Comment: (Powerhead)	91-52344
-	LIFTING EYE Comment: (Powerhead)	91-904551
-	INSTALLER KIT Comment: (Powerhead)	91-77109A3
-	INSTALLER KIT, Piston Pin Comment: (Powerhead)	91-74607A3
-	EXPANDER TOOL, Piston Ring Comment: (Powerhead)	91-24697
-	STAND, Powerhead Comment: (Powerhead)	91-812549T	91-812549 (Powerhead)
-	CAP TOOL, Flywheel Puller Comment: (Powerhead)	91-24161
-	INDICATOR TOOL, Backlash Comment: (Gear Housing)	91-8M0053505	91-78473 (Gear Housing)
-	INDICATOR TOOL, Backlash Comment: (Gear Housing)	91-196601
-	MANDREL, Bearing Driver Cup Comment: (Gear Housing)	91-31106T
-	INSTALLATION TOOL, Bearing Comment: (Gear Housing)	91-13945
-	INSTALLATION TOOL, Bearing Comment: (Gear Housing)	91-14309T02
-	PRE LOAD TOOL, Bearing Comment: (Gear Housing)	91-14311A04
-	PULLER ASSEMBLY Comment: (Gear Housing)	91-83165T
-	RACE TOOL, Bearing Comment: (Gear Housing)	91-14308T02
-	PULLER KIT, Bearing Comment: (Gear Housing)	91-31229A7
-	NUT, (.625-18) Comment: (Gear Housing)	11-24156
-	MANDREL Comment: (Gear Housing)	91-15755T
-	DRIVE HEAD TOOL Comment: (Gear Housing)	91-36569T
-	DRIVER ROD TOOL, Needle Bearings Comment: (Gear Housing)	91-37323
-	MANDREL Comment: (Gear Housing)	91-37350T
-	RETAINING TOOL, Bearing Comment: (Gear Housing)	91-43506T
-	ADAPTER KIT, Dial Indicator Comment: (Gear Housing)	91-83155
-	DIAL INDICATOR TOOL Comment: (Gear Housing)	91-58222A1
-	HOLDING TOOL, Driveshaft Comment: (Gear Housing)	91-56775T
-	INSTALLER TOOL, Bearing Comment: (Gear Housing)	91-826872
-	DRIVER TOOL, Oil Seal Comment: (Gear Housing)	91-13949
-	DRIVER, Oil Seal Comment: (Gear Housing)	91-31108T
-	LOCATION TOOL, Pinion Comment: (Gear Housing)	91-12349A05
-	PULLER JAW ASSEMBLY Comment: (Gear Housing)	91-46086A1
-	PULLER PLATE, Universal Comment: (Gear Housing)	91-37241
-	PULLER ASSEMBLY, Slide Hammer Comment: (Gear Housing)	91-34569A1
-	BEARING, Thrust Comment: (Gear Housing)	31-85560
-	TORQUE WRENCH, (0-150 lb-in) Comment: (Gear Housing)	91-66274
-	WEAR SLEEVE INSTALLATION TOOL Comment: (Gear Housing)	91-14310T1

Top Cowl

Below is the parts list for Mercury 90 (3 CYL.) Top Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	TOP COWL ASSEMBLY Comment: (Black-Electric)	100-8M0107146
1	TOP COWL ASSEMBLY Comment: (Silver-Electric)	4025-828353T8
1	TOP COWL ASSEMBLY Comment: (Black-Manual)	4026-828354T6
1	TOP COWL ASSEMBLY Comment: (Silver-Manual)	100-8M0107148
2	CAP	828716A2
3	SEAL	828352
4	SEAL	8283511
5	CAP, Upper Comment: (Black)	8218751
5	CAP, Upper Comment: (Silver)	821875F2
6	BRACKET, Cover Latch	819813T1
7	BRACKET ASSEMBLY, Latch Roller	893763	18173
8	LOCKWASHER, (.312)	13-53166
9	SCREW, (.312-18 x .625)	10-90285
10	GUIDE, Cowl Latch Bracket	F481434
11	PUSH NUT	11-91925
12	SCREW, (.250-20 x 1.00)	10-822512
13	CAP PLUG	19-823865
14	SCREW, (M6 x 16)	10-82130016
15	SUPPORT	823830
16	SCREW, (M4 x 14.5)	10-8231871
17	LOCKWASHER, Stainless Steel	8,13-26995
18	BRACKET	8233941
19	NUT, (M4)	11-8237515
20	SOUND BLANKET KIT Comment: (Hot Glue Adhesive)	823685A02	823685A 1 (Hot Glue Adhesive)
20	SOUND BLANKET KIT, (Pre-Applied Pressure Sensitive Adhesive)	823685A02	823685A 1
21	NOT SOLD SEPARATE, Sound Blanket Comment: (Manual)	NSS
21	NOT SOLD SEPARATE, Sound Blanket Comment: (Electric)	NSS
22	ROPE AND HANDLE KIT, Manual Starting	47341A11
23	NOT SOLD SEPARATE, Starter Rope	NSS
24	NOT SOLD SEPARATE, Envelope	NSS

Transom Bracket

Below is the parts list for Mercury 90 (3 CYL.) Transom Bracket:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET, Transom Comment: (Starboard)	3426-828334T02	3426-828334F 1 (Starboard)
2	BRACKET ASSEMBLY, Transom Comment: (Port)	3425-828333T07	3425-828333A 3 (Port)
3	FITTING, Grease Comment: (Port)	22-8M0169588
4	TUBE KIT, Tilt Comment: (Carbon Steel)	99170A2
4	TILT TUBE Comment: (Stainless Steel)	826125A1
5	NUT, (1.00-14) Comment: (Steel)	11-859133	11-34862, 11-90068F 3, 11-90068F 4 (Steel)
5	NUT, (1.00-14) Nylon Insert Comment: (Brass)	11-826135
6	O-RING, (.612 x .103)	25-45711
7	WASHER	13-88750
8	NUT, (.875-14) Comment: (Steel)	11-858869	11-30499 (Steel)
8	NUT, (.875-14) Comment: (Brass)	11-826164
9	SCREW, (.500-20 x 4.500)	10-8M0149747
10	WASHER, (.530 x .870 x .105) Stainless Steel	12-8M0204665
11	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
12	NUT, (.500-20)	11-82671117
13	SPRING, Tension	24-830899
14	LEVER ASSEMBLY, Tilt Lock	8M0109798	821176T02, 821176T 1
15	NYLINER	23-65830
16	SPRING, Compression	24-830900
17	KNOB	99633
18	PIN, Groove	17-99615
19	PIN	17-893709	17-99617
20	BRACKET, Anchor	8M0086406	818771T 1
21	SCREW, (M10 x 30)	10-858771
22	WASHER	12-4002319
23	NUT, (M10 x 1.5)	11-40114
24	ANODE	97-818298Q1
25	SCREW, (M6 x 25)	10-8M0204707
26	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
27	CLIP Comment: (Power Trim Model)	54-22740
28	C WASHER Comment: (Power Trim Model)	8M0084613	69205 (Power Trim Model)
29	SCREW, (#10-16 x .600) Comment: (Power Trim Model)	10-878609	10-812832 1 (Power Trim Model)
30	PUMP ASSEMBLY, Power Trim Comment: (See Power Trim Components for parts breakdown)	8M0171818
31	PIN ASSEMBLY, Tilt Lock Comment: (Manual Tilt)	17-8M0026068	17-49930A 1 (Manual Tilt)
32	DECAL, Tilt Lock Comment: (Manual Tilt)	37-830253	37-814743 3, 37-826546 (Manual Tilt)
33	NUT, (.312-18) Stainless Steel	11-826709110	11-846128, 11-F1892, F15142, MVP09802T
34	LINK ROD Comment: (Manual Tilt)	8353511
35	ARM Comment: (Manual Tilt)	832042
36	BUSHING Comment: (Manual Tilt)	23-832040
37	LEVER, Tilt Comment: (Manual Tilt)	832039
38	TILT KNOB Comment: (Manual Tilt)	8M0007469	19621 (Manual Tilt)
39	MANUAL TILT ASSEMBLY Comment: (See Manual Tilt Components for parts breakdown)	835249T1
40	SHAFT, Upper	99625002
41	PIN, Anchor	17-818898
42	PIN, Trilobe	17-821539	17-13794, 17-19603

Download this page as PDF: Click here

For Mercury Owners:

To assist you in maintaining and repairing your marine engines, we hope the following resources may be of use:

Mercury / Mercruiser / Mariner Parts from JLM Marine

About JLM Marine

Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.

As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.

We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.