Mercury 800 (6 CYL.) (1398630 THRU 1566239) Outboard Motor Parts Diagram & Catalog – Free PDF Download

by JLM Marine 30 Apr 2025 0 Comments

Mercury 800 (6 CYL.) Outboard Motor Parts Diagram & Catalog – Free PDF Download

BOTTOM COWL ASSEMBLY

Below is the parts list for Mercury 800 (6 CYL.) BOTTOM COWL ASSEMBLY:

Position No.	Part Name	OEM Number	Supersedes
1	BOTTOM COWL ASSEMBLY	186-1781A2
-	DECAL, BOTTOM COWL ("8 H.P. SIX") PORT	37-30860
-	DECAL, BOTTOM COWL ("80 H.P. SIX") STARBOARD	37-30861
-	PLUG, HOLE - BOTTOM COWL (TO PLUG 3/4" HOLE IN BOTTOM COWL)	19-31469
2	TRIM MOULDING ASSEMBLY	29997A1
3	SPLICER, TRIM MOULDING - REAR	29998
4	SCREW, DECORATIVE - MOULDING TO BOTTOM COWL	10-29226
5	WASHER, FIBER - MOULDING FASTENING SCREW	12-24671
6	NUT, NYLON CAP - MOULDING FASTENING SCREW	11-29225
7	LOCKWASHER, MOULDING FASTENING SCREW	13-26995
8	NUT, BRASS - MOULDING FASTENING SCREW	11-26419
9	BAFFLE, BOTTOM COWL	30005
10	SCREW, BAFFLE TO BOTTOM COWL	10-21106
11	BRACKET, RECTIFIER MOUNTING	30768
12	SCREW, BRACKET TO BOTTOM COWL (1 1/8")	10-21091
13	SCREW, BRACKET TO BOTTOM COWL (1 1/4")	10-56500
14	NUT, RECTIFIER BRACKET MOUNTING SCREW	11-8M0207775
15	BRACKET, PIVOT PIN TO BOTTOM COWL	30003
16	PIN, PIVOT - BOTTOM COWL	17-30004
17	NUT, PIVOT PIN FASTENING	11-20696
18	GASKET, POWERHEAD TO BOTTOM COWL	27-29914
19	SCREW, BOTTOM COWL TO DRIVE SHAFT HOUSING Comment: IF REPLACEMENT IS REQUIRED ON THIS SCREW, CHECK LENGTH OF SCREW BEFORE REPLACING, AS ENGINES WERE PRODUCED WITH TWO DIFFERENT LENGTH SCREWS, SUCH AS, C-10-24963 (7/8" LONG) AND C-10-21504 (1 1/4" LONG).	10-21504
20	BRACKET, CABLE END ANCHOR	20557
21	SCREW, ANCHOR BRAKCET TO BOTTOM COWL	10-29200
22	LEVER, THROTTLE CONTROL	29532
23	LEVER, SHIFT CONTROL	30612
24	BUSHING, THROTTLE AND SHIFT LEVER	23-29529
25	SCREW, THROTTLE AND SHIFT LEVER FASTENING	10-47273
26	WASHER, THROTTLE AND SHIFT LEVER FASTENING SCREW	12-8M0042641	12-29395
27	PIN ASSEMBLY, CLEVIS YOKE	17-30978A1
28	ROLL PIN, CLEVIS YOKE PIN	17-239281
29	SCREW, CLEVIS PIN FASTENING	10-20584
30	WASHER, WAVE - PIN FASTENING SCREW	13-29402
31	NUT, PIN FASTENING SCREW	11-8M0204718
32	SHIFT SHAFT ASSEMBLY, UPPER	30789A1
33	ROD (SLEEVE), SHIFT CONTROL END	27714
34	NUT, SHIFT SHAFT END ADJUSTING	11-25168
35	ROD, LINK - SHIFT SHAFT END	30630
36	COTTER PIN, LINK ROD TO SHIFT SHAFT	18-210711
37	WASHER, LINK ROD	12-20583
38	SPRING, DETENT	24-30621
39	SCREW, DETENT SPRING TO BOTTOM COWL	10-98256
40	WASHER, DETENT SPRING SCREW	12-69057
41	NUT, DETENT SPRING SCREW	11-8M0207775

CARBURETOR ASSEMBLY

Below is the parts list for Mercury 800 (6 CYL.) CARBURETOR ASSEMBLY:

Position No.	Part Name	OEM Number
1	CARBURETOR ASSEMBLY, COMPLETE (KA-11A)	1333-1943
1	CARBURETOR ASSEMBLY, COMPLETE (KA-14A)	1333-1943
2	FLOAT ASSEMBLY	1395-8673
3	PIN, FLOAT LEVER PINION	17-20853
4	LEVER, FLOAT (LOWER)	1399-102
5	LEVER, FLOAT (UPPER)	1399-101
6	INLET NEEDLE, SEAT AND GASKET	1395-92581
7	GASKET, INLET SEAT	27-25033
8	SCREW, THROTTLE STOP LEVER	1395-6027
9	LEVER, THROTTLE STOP Comment: USED ON CENTER AND LOWER CARBURETOR ONLY -- REPLACED WITH 27977 CLUSTER	8146791
10	SHAFT, THROTTLE	1399-2012
11	SPRING, THROTTLE SHAFT RETURN (CENTER AND LOWER CARBURETOR)	24-26890
11	SPRING, THROTTLE SHAFT RETURN(UPPER CARBURETOR)	24-20869
12	JET, MAIN (.069)-STANDARD	1399-1962
12	JET, MAIN FUEL (.067)	1399-1467
12	JET, MAIN FUEL (.065)-STANDARD	1399-1465
12	JET, MAIN FUEL (.065)-STANDARD	1399-1465
12	JET, MAIN FUEL (.063)	1399-1463
12	JET, MAIN FUEL (.061)	1399-1461
12	JET, MAIN FUEL (.059)	1399-1459
13	GASKET, MAIN FUEL JET	27-28409
14	SPRING, IDLE ADJUSTMENT SCREW	24-27160
15	SCREW, IDLE ADJUSTMENT	1399-1713
16	GASKET, FLOAT BOWL COVER	1399-99
17	COVER, FLOAT BOWL	1399-1133
18	SCREEN, FILTER	1399-3938
19	SCREW, FLOAT BOWL COVER (SHORT)	10-22625
20	SCREW, FLOAT BOWL COVER (LONG)	10-25850
21	GASKET, STRAINER COVER (LARGE)	27-25851
22	GASKET, STRAINER COVER (SMALL)	27-25849
23	COVER STRAINER	1399-1135
24	GASKET, STRAINER COVER SCREW	27-25848
25	SCREW, STRAINER COVER FASTENING	10-25822
26	NOZZLE, MAIN	1399-1739
27	SCREW, PLUG-MAIN NOZZLE	10-23178
28	SCREW AND LOCKWASHER, THROTTLE SHUTTER	10-23035
29	SHUTTER, THROTTLE	1399-1740
30	TUBE, IDLE	1399-1828
30	TUBE, IDLE	1399-1702
31	GASKET, IDLE TUBE	27-23180
32	SCREW, PLUG-BODY CHANNEL	10-28845
33	WELCH PLUG, BODY CHANNEL	19-20011
34	SCREW, PLUG-MAIN FUEL JET CHANNEL	10-28405
35	GASKET, JET CHANNEL PLUG SCREW	27-28406
--	GASKET AND PACKING SET (1 PER CARBURETOR)	1399-2015
--	REPAIR PARTS KIT(1 PER CARBURETOR)	1399-1829
--	REPAIR PARTS KIT(1 PER CARBURETOR)	1399-1963
36	GASKET, CARBURETOR FLANGE	27-757911
37	NUT, CARBURETOR MOUNTING STUD	11-29250

CARBURETOR LINKAGE AND CHOKE SOLENOID

Below is the parts list for Mercury 800 (6 CYL.) CARBURETOR LINKAGE AND CHOKE SOLENOID:

Position No.	Part Name	OEM Number	Supersedes
1	CHOKE SOLENOID, TOP COWL	29690
2	TERMINAL, CHOKE SOLENOID LEAD	30050
3	SCREW, CHOKE SOLENOID TO TOP COWL	10-24773
4	LOCKWASHER, CHOKE SOLENOID SCREW	13-26991
5	SCREW, CHOKE SOLENOID TO TOP COWL	10-20540
6	LOCKWASHER, CHOKE SOLENOID SCREW	13-26992
7	GROUND STRAP ASSEMBLY, CHOKE SOLENOID TO ADAPTOR	397-421A2
8	CLIP, CHOKE SOLENOID WIRE	54-648552
9	SCREW, WIRE CLIP TO TOP COWL	10-24239
10	"D" WASHER, WIRE CLIP FASTENING SCREW	8M0084613	69205
11	"S" CLIP, CHOKE SOLENOID WIRE TO TOP COWL	54-22783
12	KNOB, CHOKE ROD	90242A1
13	GROMMET, CHOKE ROD	25-20116
14	"U" LINK, CHOKE KNOB TO CHOKE ROD	22462
15	SCREW, "U" LINK TO CHOKE KNOB	10-69022
16	LOCKWASHER, "U" LINK SCREW	13-26996
17	COTTER PIN, "U" LINK TO CHOKE ROD	18-26953
18	PLUNGER AND LINK ASSEMBLY, CHOKE SOLENOID	27031A1
19	WASHER, PLUNGER AND LINK	12-30164
20	COTTER PIN, LINK TO UPPER CHOKE LEVER	18-26953
21	CLUSTER, THROTTLE LEVER (UPPER CARBURETOR)	27977
22	SCREW, CLUSTER TO THROTTLE LEVER	1395-6027
23	CARBURETOR ASSEMBLY, COMPLETE	1333-1943
23	CARBURETOR ASSEMLBY, COMPLETE	1333-1943
24	SCREW, THROTTLE BRACKET MOUNTING	10-29239
25	THROTTLE PICKUP BRACKET ASSEMBLY Comment: USE ON ENGINES FROM SERIAL #1406356 AND BELOW.	53649A2
26	CLAMP, THROTTLE PICKUP BRACKET Comment: USE ON ENGINES FROM SERIAL #1406356 AND BELOW.	27870
27	SCREW, UPPER AND LOWER CLAMP FASTENING Comment: USE ON ENGINES FROM SERIAL #1406356 AND BELOW.	10-69022
28	WASHER, CLAMP FASTENING SCREW Comment: USE ON ENGINES FROM SERIAL #1406356 AND BELOW.	12-30164
25	THROTTLE PICKUP BRACKET ASEMBLY Comment: USE ON ENGINES FROM SERIAL #1406357 AND UP	53649A2
29	BRACKET, COIL LEAD REATINER	26977
30	SCREW, RETAINER BRAKCET TO CENTER CARBURETOR	10-98253
31	LOCKWASHER, BRACKET FASTENING SCREW	13-21272
32	ROD, CHOKE	30750
33	STUD, CARBURETOR-CHOKE SHUTTER PIVOT	16-30172
34	SHUTTER, CHOKE-CARBURETOR	38604
35	BUSHING, NYLON-UPPER CHOKE SHUTTER	23-30438
36	RIVET, CHOKE SHUTTER TO CHOKE ROD	17-25391
37	WASHER, CHOKE SHUTTER CARBURETOR STUD	12-30164
38	NUT, CHOKE SHUTTER TO CARBURETOR STUD	11-20110
39	SPRING, CHOKE ROD TENSION	24-28965
40	RETAINER, CHOKE ROD SPRING TO CARBURETOR	27711
40	RETAINER, CHOKE ROD SPRING TO CARBURETOR-NOT AS SHOWN	31479
41	SCREW, RETAINER TO LOWER CARBURETOR	10-28713

CLAMP AND SWIVEL BRACKET ASSEMBLY

Below is the parts list for Mercury 800 (6 CYL.) CLAMP AND SWIVEL BRACKET ASSEMBLY:

Position No.	Part Name	OEM Number	Supersedes
1	CLAMP BRACKET ASSEMBLY	1440-3296A1
2	THUMB SCREW ASSEMBLY	28403A3
3	WASHER, THUMB SCREW	12-28404
4	TUBE, TILT - CLAMP BRACKET TO SWIVEL BRACKET	8M0041936	8M0035074, 883067, 30664 2, 74528
5	SHIM, CLAMP BRACKET TILT TUBE (.010-.020)	12-52864
6	NUT, TILT TUBE FASTENING	11-858869	11-30499
7	CAP, PLASTIC-TILT TUBE	53078
8	SPACER, CLAMP BRACKET STUD	23-59624
9	STUD, CLAMP BRACKET	16-59625
10	LOCKWASHER, CLAMP BRACKET STUD	13-8M0204647
11	NUT, CLAMP BRACKET STUD	11-22053
12	TILT LOCK PIN ASSEMBLY	17-8M0026068	17-49930A 1
13	SLEEVE, RUBBER - TILT LOCK PIN BUMPER	32-28052
14	SWIVEL BRACKET ASSEMBLY	1453-1814A1
15	FITTING, GREASE	22-69059
16	OIL SEAL	26-32911
17	SPRING, COIL - SWIVEL BRACKET	24-94891
18	PIN, COIL SPRING MOUNTING	17-28658
19	LUBRICAP, SWIVEL PIN GEAR FITTING	19-77633Q
20	SPACER, RUBBER - COIL SPRING POSITITIONING	23-28688
21	PIN, REVERSE LOCK SPRING ATTACHING	17-25598
22	SWIVEL PIN AND TOP YOKE ASSEMBLY	17-30784A1
23	BUMPER, TOP YOKE	28203
24	BOLT, TOP YOKE TO UPPER MOUNT (5 1/2")	10-30453
24	BOLT, TOP YOKE TO UPPER MOUNT (5 3/4")	10-49554
25	NUT, TOP YOKE BOLT FASTENING	11-8M0204653
26	WAHSER, SWIVEL PIN - LOWER (TOP WASHER OPTIONAL)	12-25176
27	WASHER, RUBBER - UPPER SHIFT SHAFT	12-30610
27A	BOOT, RUBBER - UPPER SHIFT SHAFT	30614
27A	BOOT, RUBBER - UPPER SHIFT SHAFT (NOT AS SHOWN)	31234
28	WAHSER, NYLON - UPPER SHIFT SHAFT	12-30611
29	SERIAL PLATE	38-56267
30	SCREW, DRIVE - SERIAL PLATE TO SWIVEL BRACKET	10-25612
31	STRAP STOP, DRIVE SHAFT HOUSING TO SWIVEL BRACKET	28205T
32	SCREW, STRAP STOP TO DRIVE SHAFT HOUSING	10-28200
33	NUT, STRAP STOP FASTENING SCREW	11-25269
34	YOKE, BOTTOM	30451
35	NUT, SWIVEL PIN RETAINING	11-71956
36	SPRING, REVERSE LOCK TENSION	24-29821
37	REVERSE LOCK ASSEMBLY	26903A4
38	SHAFT, REVERSE LOCK PIVOT	56349
39	COTTER PIN, REVERSE LOCK TO SHAFT	18-45882
40	TILT STOP LEVER ASSEMBLY	30126A1
41	SCREW, TILT STOP LEVER ANCHOR	10-30128
42	WASHER, WAVE - LEVER ANCHOR SCREW	13-31030
43	NUT, LEVER ANCHOR SCREW	11-29250
44	PIN, UPPER SHOCK MOUNTING	55-28416
45	SPACEER, UPPER SHOCK BUSHING TO CLAMP BRACKET	23-28199
46	WASHER, UPPER BUSHING RETAINER (INNER)	12-28196
47	WASHER, UPPER AND LOWER BUSHING RETAINER (OUTER)	12-8M0204648
48	SCREW, NYLOCK - UPPER AND LOWER SHOCK MOUNTING PIN	10-28450
49	SHOCK ABSORBER	55-28209
50	BUSHING, RUBBER - SHOCK ABSORBER	23-28198
51	PIN, LOWER SHOCK MOUNTING	55-696531
52	WASHER, LOWER BUSHING RETAINER (INNER)	12-8M0204695
53	BOLT, CLAMP BRACKET TO BOAT TRANSOM	10-68298
54	WASHER, CLAMP BRACKET BOLT	12-68410
55	NUT, CLAMP BRACKET BOLT	11-82670912

COWLING AND FRONT COVER

Below is the parts list for Mercury 800 (6 CYL.) COWLING AND FRONT COVER:

Position No.	Part Name	OEM Number
1	COWL FRONT COVER ASSEMBLY	184-2043A3
2	EMBLEM, FRONT COVER	26183A5
3	SCREW, BRACKET TO FRONT COVER	10-29226
4	LOCKWASHER, BRACKET FASTENING SCREW	13-26995
5	NUT, BRACKET FASTENING SCREW	11-26419
6	BUMPER, RUBBER - FRONT COVER BRACKET	29345
7	KNOB, COWL FRONT COVER FASTENING	56849
8	WASHER, COVER FASTENING KNOB (RUBBER)	12-30771
9	WASHER, COVER FASTENING KNOB (STEEL)	12-26825
10	SPRING, TENSION - FASTENING KNOB	24-30772
11	ROLL PIN, TENSION SPRING TO KNOB	17-29077
12	BLANKET, SOUND ABSORBING	30287
12A	STRIP, RUBBER - COWL FRONT COVER	31089
13	WRAP AROUDN COWL ASSEMBLY	2120-2509A5
14	HANDLE, COWL LATCH	46785A1
15	"E" RING, COWL LATCH HINGE PIN	53-21058
16	PIN, HINGE - COWL LATCH HANDLE	17-21057
17	SWIVEL, COWL LATCH	46785A1
18	HOOK, COWL LATCH FASTENING	30413
19	BLANKET, SOUND ABSORBING - WRAP AROUND COWL	30021
--	GLUE, ADHESIVE - BLANKET FASTENINIG	92-86166Q1
--	ADHESIVE COMPOUND (3 1/2 OUNCE KIT) EMBLEM FASTENING	92-271091

CRANKSHAFT, PISTONS AND CONNECTING RODS

Below is the parts list for Mercury 800 (6 CYL.) CRANKSHAFT, PISTONS AND CONNECTING RODS:

Position No.	Part Name	OEM Number
1	CRANKSHAFT	417-1787
2	KEY, FLYWHEEL DRIVE	28-45554
3	CENTER MAIN BEARING ASSEMBLY	521-1490A1
4	DOWEL PIN, CENTER MAIN BEARING	17-20032
5	BEARING, NEEDLE-OUTER RACE	29-714221
6	RACE, OUTER (PAIR)	26113T
7	RING, SNAP-OUTER RACE	53-26933
8	DOWEL PIN, STEPPED	17-27732
9	SCREW, CENTER MAIN BEARING CLAMPING	10-22968
10	NUT, BEARING CLAMPING SCREW	11-8M0207775
11	MAIN BEARING ASSEMBLY, VALVE TYPE	527-1932A2
12	DOWEL PIN, MAIN BEARING	17-20032
13	SCREW, MAIN BEARING CLAMPING-SEE NOTE BELOW Comment: ON EARLIER MERC 800E ENGINES, A C-10-30259 SCREW (MAIN BEARING CLAMPING) WAS USED WITH NO NUT. FOR REPLACEMENT ORDER C-10-25313 SCREW AND C-11-29469 NUT AS LISTED.	10-25313
--	NUT, MAIN BEARING CLAMPING SCREW Comment: ON EARLIER MERC 800E ENGINES, A C-10-30259 SCREW (MAIN BEARING CLAMPING) WAS USED WITH NO NUT. FOR REPLACEMENT ORDER C-10-25313 SCREW AND C-11-29469 NUT AS LISTED.	11-29469
14	REED SET, MATCHED-MAIN BEARING	34-88498A1
15	REED STOP, MAIN BEARING REED VALVES	34-20053
16	WASHER, REED STOP MOUNTING SCREW	12-26014
17	SCREW, REED STOP MOUNTING	10-20055
--	NUT, REED STOP MOUNTING SCREW	11-29469
18	PISTON AND PISTON PIN ASSEMLBY	729-1948A2
19	LOCK RING, PISTON PIN	40-30002
20	RING, PISTON	39-30587A12
21	CONNECTING ROD AND CAP ASSEMBLY	611-1747A3
22	SCREW, CONNECTING ROD	10-45379
23	NUT, CONNECTING ROD SCREW	11-20061
24	BEARING, NEEDLE-CRANKPIN	29-47897
25	BEARING, NEEDLE-PISTON PIN	29-39656
26	WASHER, NEEDLE LOCATING	12-29681
--	PISTON AND PISTON PIN ASSEMBLY (.015 OVERSIZE) Comment: OVERSIZE PISTONS AND RINGS	729-1949A2
--	RING, PISTON (.015 OVERSIZE) Comment: OVERSIZE PISTONS AND RINGS	39-30704A12

CYLINDER BLOCK AND CRANKCASE ASSEMBLY

Below is the parts list for Mercury 800 (6 CYL.) CYLINDER BLOCK AND CRANKCASE ASSEMBLY:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER BLOCK AND CRANKCASE ASSEMBLY Comment: 833-1919A2 CYLINDER BLOCK ASSEMBLY CAN BE USED IN PLACE OF 833-1688A2 AND 833-1919A1 CYLINDER BLOCK ASSEMBLIES. 833-1919A2 CYLINDER BLOCK ASSEMBLY INCLUDES COVER, GASKET, ETC.	833-1919A2
1	CYLINDER BLOCK AND CRANKCASE ASSEMBLY Comment: 833-1919A2 CYLINDER BLOCK ASSEMBLY CAN BE USED IN PLACE OF 833-1688A2 AND 833-1919A1 CYLINDER BLOCK ASSEMBLIES. 833-1919A2 CYLINDER BLOCK ASSEMBLY INCLUDES COVER, GASKET, ETC.	833-1919A2
2	PIN, DOWEL-CYLINDER BLOCK TO MAIN BEARING	17-20032
3	BUSHING, CRANKCASE-COWL MOUNTING STUD	23-26348
4	STUD, CARBURETOR MOUNTING	16-21831
5	PIN, DOWEL-CRANKCASE TO CYLINDER BLOCK	17-43044
6	STUD, CRANKCASE TO DRIVE SHAFT HOUSING	16-64281
7	STUD, CYLINDER BLOCK TO DRIVE SHAFT HOUSING	16-26135
8	STUD, CYLINDER BLOCK TO DRIVE SHAFT HOUSING	16-26134
9	PLUG, PIPE-CYLINDER BLOCK	22-328022
10	SCREW, CRANKCASE TO CYLINDER BLOCK (3 1/4")	10-29877
10	SCREW, CRANKCASE TO CYLINDER BLOCK (2 1/2")	10-26132
11	SCREW, CRANKCASE TO CYLINDER BLOCK (1 5/8")	10-69091
11	SCREW, CRANKCASE TO CYLINDER BLOCK (1 1/2")	10-78841
12	NUT, CRANKCASE FASTENING SCREW	11-29250
13	BRACKET, CLAMP EXTENSION	53-78201
14	SCREW, MAIN BEARING LOCKING	10-20089
15	SCREW, CENTER MAIN BEARING LOCKING	10-20359
16	TAB WASHER, BEARING LOCKING SCREW	14-20091
17	END CAP ASSEMBLY, UPPER	1125-1675A1
18	OIL SEAL	26-41953
19	"O" RING	25-20081
20	BEARING, BALL	30-63742T
21	SHIM, END CAP TO CRANKCASE (.002-3-5-10)	15-20082A1
22	SCREW, END CAP MOUNTING	10-30225
23	END CAP ASSEMBLY, LOWER	1126-1751A1
24	OIL SEAL, UPPER	26-41953
25	OIL SEAL, LOWER	26-29478
26	"O" RING	25-20081
27	BEARING, BALL	30-63742T
28	CHECK VALVE ASSEMBLY, END CAP	21-28481A1
29	SHIM, END CAP TO CRANKCASE (.002-3-5-10)	15-20085A1
30	SCREW, END CAP MOUNTING	10-30225
31	GASKET, CYLINDER BLOCK TO MANIFOLD PLATE	27-30013
32	PLATE, EXHAUST MANIFOLD	30066
33	GASKET, MANIFOLD PLATE TO CEVER	27-30012
34	COVER, EXHAUST MANIFOLD	29888
34	COVER, EXHAUST MANIFOLD	31303
35	CREW, MANIFOLD COVER MOUNTING	10-28667
36	CLAMP, SPARK PLUG LEADS TO COVER	54-26519
37	GROUND STRAP ASSEMBLY, CYLINDER BLOCK TO BOTTOM COWL	30109
38	SWITCH, MERCURY	58124A1
39	CLAMP, MERCURY SWITCH HOLDING	54-22875
40	"D" WASHER, CLAMP FASTENING SCREW	8M0084613	69205
41	SCREW, MERCURY SWITCH CLAMP TO EXHAUST COVER	10-20401
42	GASKET, CYLINDER BLOCK COVER	27-31798
42	GASKET, CYLINDER BLOCK COVER	27-31798
43	CYLINDER BLOCK COVER ASSEMBLY	1011-1946A1
43	CYLINDER BLOCK COVER ASSEMBLY	1011-1946A1
44	BUSHING, COVER-COWL MOUNTING STUD	23-26348
45	SCREW, CYLINDER BLOCK COVER MOUNTING	10-20653
46	NUT, COVER MOUNTING SCREW	11-8M0207775
47	GASKET, TRANSFER PORT COVER	27-29866
48	COVER, TRANSFER PORT	29886
49	SCREW, TRANSFER PORT COVER MOUNTING (5/8")	10-20540
49	SCREW, TRANSFER PORT COVER AND RESISTOR SNUBBER MOUNTING Comment: (1 3/8")	10-24770
50	LOCKWASHER, TRANSFER PORT COVER AND SNUBBER MOUNTING SCREW	13-26992
51	CONNECTOR, CYLINDER BLEED HOSE-LOWER AND CENTER	22-67902
52	HOSE, UPPER AND LOWER CYLINDER BLEED	32-9912688
53	TEE, CHECK VALVE AND ADAPTOR	22-25956
54	ADAPTOR AND CHECK VALVE ASSEMBLY	22-28586A1
55	CHECK VALVE ASSEMBLY-ADAPTOR	21-28481A1
56	CHECK VALVE ASSEMBLY, UPPER-BLEED HOSE	22-62365A1
55	CHECK VALVE ASSEMBLY	21-28481A1
57	CLAMP, BLEED HOSE TO CONNECTOR	54-20387

DISTRIBUTOR ADAPTOR AND PILOT ASSEMBLY

Below is the parts list for Mercury 800 (6 CYL.) DISTRIBUTOR ADAPTOR AND PILOT ASSEMBLY:

Position No.	Part Name	OEM Number	Supersedes
1	RING, SNAP - BALL BEARING RETAINING	53-26406
2	BEARING, BALL - DRIVE SHAFT	30-26379
3	DRIVE SHAFT, DISTRIBUTOR	45-30573
4	PILOT ASSEMBLY	45960A1
5	BEARING, BALL - DISTRIBUTOR PILOT	30-20066
6	SPRING, HORSESHOE	24-29275
7	PIN, SPRING TERMINAL	17-27962
8	WASHER, SPRING TERMINAL PIN	12-8M0204649
9	ECONOMIZER COLLAR AND PIN ASSEMBLY	55804A1
10	PIN, SPRING RETAINER	17-27961
11	FITTING, GREASE - ECONOMIZER COLLAR	22-25094
12	THROTTLE ACTUATOR ASSEMBLY	30926A1
13	BUSHING, NYLON - THROTTLE ACTUATOR	23-26602
14	SCREW, THROTTLE ACTUATOR TO SECTOR GEAR	10-69022
15	WASHER, THROTTLE ACTUATOR FASTENING SCREW	12-847883	12-20128
16	LOCKWASHER, THROTTLE ACTUATOR FASTENING SCREW	13-26996
17	ADAPTOR, DISTRIBUTOR	30645
18	FITTING, GREASE - ADAPTOR	22-25094
19	SCREW, ADAPTOR AND PILOT TO CRANKCASE FLANGE	10-78841
20	WASHER, ADAPTOR AND PILOT FASTENING SCREW	12-20084
21	NUT, ADAPTOR AND PILOT FASTENING SCREW	11-22053
22	WASHER, THRUST - DISTRIBUTOR PILOT	12-27939
23	TAB WASHER, CAP LOCKING	14-27960
24	WASHER, WAVE - TAB WASHER TENSION	13-27959
25	CAP, ADAPTOR AND PILOT FASTENING	27955
26	SCREW, ADAPTOR AND PILOT TO DISTRIBUTOR	10-28668
27	LOCKWASHER, ADAPTOR AND PILOT TO DIST. SCREW	13-26992
28	SPACER, DRIVEN PULLEY	23-29909
29	DRIVEN PULLEY ASSEMBLY	29906A1
30	PIN, DRIVEN PULLEY	17-29908
31	FLANGE, DRIVEN PULLEY	29907
32	KEY, MAGNETO DRIVING	28-29910
33	SCREW, PULLEY CLAMPING	10-41506
34	LOCKWASHER, PULLEY CLAMPING SCREW	13-26996
35	BELT, TIMING	20140
36	GROUND STRAP ASSEMBLY, ADAPTOR TO CRANKCASE	30109

DISTRIBUTOR ASSEMBLY, COMPLETE

Below is the parts list for Mercury 800 (6 CYL.) DISTRIBUTOR ASSEMBLY, COMPLETE:

Position No.	Part Name	OEM Number	Supersedes
-	DISTRIBUTOR ASSEMBLY, COMPLETE	393-1282A17
1	HOUSING, PRIMARY	393-1282
2	ELBOW ASSEMBLY, VENT HOSE - PRIMARY HOUSING	22-25885A1
3	BREAKER ASSEMBLY, COMPLETE	393-1504A11
4	STUD, PRIMARY LEAD AND TENSION SPRING	16-29230
5	NUT, PRIMARY LEAD FASTENING	11-29236
6	GROMMET, PLASTIC - BREAKER ASSEMBLY	393-1586
7	WASHER, BREAKER PIVOT PIN	12-26439
8	COTTER PIN, BREAKER TO PIVOT PIN	18-26953
9	CAM WOCK AND HOLDER ASSEMBLY	393-1287A2
10	SCREW, BREAKER HOLDER TO HOUSING	10-20597
11	CONDENSER	393-1283A1
12	SCREW, CONDENSER TO HOUSING	10-29434
13	WIRE, PRIMARY GROUND	393-1656
14	BEARING, BALL - CAM SHAFT	30-26379
15	SHAFT ASSEMBLY - DISTRIBUTOR CAM	393-1779A2
16	BUSHING, DISTRIBUTOR CAM SHAFT	23-28933
17	"O" RING, CAM SHAFT	25-26543
18	PIN, ROLL - CAM SHAFT	17-25319
19	WASHER, WAVE - BALL BEARING TENSION	13-26917
20	ADAPTOR, HOUSING TO DISTRIBUTOR CAP	393-1278
22	SCREW, ADAPTOR TO HOUSING	10-32651
23	ROTOR, DISTRIBUTOR	393-1280A1
24	GASKET, DISTRIBUTOR CAP TO ADAPTOR	27-26446
25	DISTRIBUTOR CAP ASSEMBLY	393-1927A9
26	BRUSH AND SPRING ASSEMBLY	393-1293A1
27	ELBOW, VENT HOSE - DISTRIBUTOR CAP	22-996642
28	SIDE INLET ASSEMBLY	F1277
29	BRUSH AND SPRING ASSEMBLY	393-1292A1
30	GASKET, SIDE INLET TO DISTRIBUTOR CAP	27-26447
31	SCREW, SIDE INLET TO DISTRIBUTOR CAP	10-29167
32	SCREW, DISTRIBUTOR CAP TO ADAPTOR	10-29158
33	TAB WASHER, DISTRIBUTOR CAP FASTENING SCREW	14-29157
34	HIGH TENSION CABLE ASSEMBLY (COIL 2)	84-821945A37	84-813706A37, 84-93475A33
35	HIGH TENSION CABLE ASSEMBLY (COIL 1)	84-821945A27	84-813706A27, 84-93475A32
36	SLEEVE, TERMINAL END COVER	85-94589
37	CONNECTOR, HIGH TENSION CABLE (CAP END)	8M0084600	20121
38	GROMMET, HIGH TENSION CABLE	25-26547
39	SPARK PLUG LEAD ASSEMBLY (3, 4 AND 5)	84-813715A1
40	SPARK PLUG LEAD ASSEMBLY (2 AND 6)	84-813715A1
41	SPARK PLUG LEAD ASSEMBLY (1)	84-813715A1
37	CONNECTOR, SPARK PLUG LEAD	8M0084600	20121
36	SLEEVE, TERMINAL END COVER	85-94589
42	SLEEVE, SPARK PLUG LEAD	32-30574
43	SLEEVE, SPARK PLUG LEAD	32-46768
44	PROTECTOR, SPARK PLUG LEAD	85-63709A1

DISTRIBUTOR VERTICAL LINKAGE AND IGNITION COILS

Below is the parts list for Mercury 800 (6 CYL.) DISTRIBUTOR VERTICAL LINKAGE AND IGNITION COILS:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET, STOP	55805
2	SCREW, STOP BRACKET ADJUSTING	10-24228
3	NUT, STOP BRACKET ADJUSTING SCREW	11-20890
4	CAP, NYLON - ADJUSTING SCREW	26852
5	SCREW, STOP BRACKET TO DISTRIBUTOR ADAPTOR	10-28636
6	WASHER, STOP BRACKET FASTENING SCREW	12-20533
7	SWIVEL, LINKAGE - ECONOMIZER COLLAR	27947
8	SWIVEL AND LINK ROD ASSEMBLY	25996A1
9	ROD, LINK - UPPER	27949
10	NUT, UPPER LINK ROD ADJUSTING	11-25168
11	SWIVEL, UPPER AND LOWER LINK RODS	27948
12	LEVER, LINKAGE - UPPER	30582
13	LEVER, LINKAGE - LOWER	30619
14	ROD, LINK - LOWER	30623
15	SHAFT, VERTICAL	30629
16	BUSHING, NYLON - VERTICAL SHFT	23-26954
17	ROLL PIN, VERTICAL SHAFT AND LINKAGE LEVERS	17-25319
18	WASHER, UPPER AND LOWER SWIVEL	12-8M0204649
19	NUT, UPPER AND LOWER SWIVEL TO LEVER AND BRACKET	11-8267089
20	SCREW, SET - LINKAGE LEVER	10-25781
21	WASHER, VERTICAL SHAFT - CENTER	12-20553
22	DISTRIBUTOR ASSEMBLY, COMPLETE	393-1282A17
23	SPARK PLUG (J4J)	33-813413	33-30578
24	CLIP, DISTRIBUTOR PRIMARY GROUND LEAD (1/4-6)	54-24836
25	"D" WASHER, GROUND LEAD CLIP SCREW	8M0084613	69205
26	SCREW, DISTRIBUTOR GROUND LEAD CLIP TO CRANKCASE	10-8M0113176
27	COIL, IGNITION	898253T24	392-806529A 1
28	LOCKWASHER, IGNITION COIL TERMINALS	13-20554
29	LOCKWASHER, IGNITION COIL TERMINALS	13-26996
30	NUT, IGNITION COIL TERMINALS	11-68219
31	"O" RING, IGNITION COIL	25-26543
32	JUMPER, COIL TO COIL	28922
33	BRACKET, COIL FASTENING	26514
34	BAND, COIL BRACKET	26512
35	SCREW, COIL BAND TO BRACKET	10-26889
36	NUT, COIL BAND SCREW	11-8M0207775
37	SCREW, COIL BRACKET TO BOTTOM COWL (1 1/2")	10-20784
38	SCREW, COIL BRACKET TO BOTTOM COWL (2 1?4")	10-26889
39	NUT, COIL BRACKET SCREW	11-8M0207775
40	STUD, COIL BRACKET TO SUPPORT	16-20077
41	SUPPORT, EXTERNAL WIRING HARNESS	30238
42	WASHER, COIL BRACKET STUD	12-20084
43	NUT, COIL BRACKEET STUD	11-862902	11-25594
44	CONNECTOR, DISTRIBUTOR VENT TUBE	22-291112
45	HOSE, VENT - DISTRIBUTOR TO CONNECTOR (13")	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
46	ELBOW, DISTRIBUTOR VENT TUBE	22-996642
47	HOSE, VENT - DISTRIBUTOR TO ELBOW (16")	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821

DRIVE SHAFT HOUSING ASSEMBLY

Below is the parts list for Mercury 800 (6 CYL.) DRIVE SHAFT HOUSING ASSEMBLY:

Position No.	Part Name	OEM Number
1	DRIVE SHAFT HOUSING ASSEMBLY	1540-2384A2
2	STUD, DRIVE SHAFT HOUSING TO GEAR HOUSING	16-56295
3	COVER, TRIM - DRIVE SHAFT HOUSING	35638A1
4	SCREW, TRIM COVER TO DRIVE SHAFT HOUSING	10-30742
5	DECAL,"FULL GEAR SHIFT"-STARBOARD	37-31022
5	DECAL,"FULL GEAR SHIFT"-PORT	37-31023
6	TUBE, WATER INLET	32-30722
7	SEAL, RUBBER - WATER INLET TUBE	26-26207
8	GASKET, DRIVE SHAFT HOUSING TO BOTTOM COWL	27-26198
9	WASHER, POWERHEAD STUDS	12-20086
10	NUT, POWERHEAD STUDS	11-8M0204726
11	NUT, POWERHEAD STUDS	11-23161
12	PLUG, PLASTIC - WATER PICK-UP SCREW HOLE	19-29850
13	NUT, GEAR HOUSING AND DRIVE SHAFT HOUSING STUDS	11-8M0204653
14	NUT, GEAR HOUSING AND DRIVE SHAFT HOUSING STUDS	11-29489
15	ROD, PUSH - REVEERSE LOCK	30721
16	PIN, REVERSE LOCK LEVER	17-30615
17	SPRING, TENSION - PUSH ROD	24-30618
18	LEVER, REVERSE LOCK	52920
19	WAHSER, PUSH ROD	12-20546
20	COTTER PIN, PUSH ROD TO REVERSE LOCK	18-25191
21	BOOT, RUBBER - PUSH ROD	30614
22	RETAINER, PUSH ROD RUBBER BOOT	31039
23	CAP, RUBBER - UPPER MOUNT BOLT NUT Comment: USE ON ENGINES FROM SERIAL #1405679 AND BELOW	25305
24	NUT, UPPER MOUNT BOLT Comment: USE ON ENGINES FROM SERIAL #1405679 AND BELOW	11-8M0204653
25	WASHER, UPPER MOUNT BOLT Comment: USE ON ENGINES FROM SERIAL #1405679 AND BELOW	12-30514
26	WASHER, RUBBER - UPPER MOUNT BOLT Comment: USE ON ENGINES FROM SERIAL #1405679 AND BELOW	12-30516
27	WASHER, UPPPER MOUNT BOLT Comment: USE ON ENGINES FROM SERIAL #1405679 AND BELOW	12-30515
28	COVER, UPPER MOUNT - OUTSIDE HALF Comment: USE ON ENGINES FROM SERIAL #1405679 AND BELOW	26218
29	COVER, UPPER MOUNT - INSIDE HALF Comment: USE ON ENGINES FROM SERIAL #1405679 AND BELOW	26217
30	MOUNT, RUBBER - UPPER Comment: USE ON ENGINES FROM SERIAL #1405679 AND BELOW	30513
23	CAP, RUBBER - UPPER MOUNT BOLT NUT Comment: USE ON ENGINES FROM SERIAL #1405680 AND UP	31264
24	NUT, UPPPER MOUNT BOLT Comment: USE ON ENGINES FROM SERIAL #1405680 AND UP	11-8M0204653
25	WASHER, UPPER MOUNT BOLT Comment: USE ON ENGINES FROM SERIAL #1405680 AND UP	12-31263
26	WASHER, RUBBER - UPPER MOUNT BOLT Comment: USE ON ENGINES FROM SERIAL #1405680 AND UP	12-31261
27	WASHER, UPPER MOUNT BOLT Comment: USE ON ENGINES FROM SERIAL #1405680 AND UP	12-31262
28	COVER, UPPER MOUNT - OUTSIDE HALF Comment: USE ON ENGINES FROM SERIAL #1405680 AND UP	31260
29	COVER, UPPER MOUNT - INSIDE HALF Comment: USE ON ENGINES FROM SERIAL #1405680 AND UP	53141
30	MOUNT, RUBBER - UPPER Comment: USE ON ENGINES FROM SERIAL #1405680 AND UP	75296
31	PACKING,"U" CUP	24929
32	SCREW, UPPER MOUNT COVER (1 5/8")	10-20012
33	SCREW, UPPER MOUNT COVER (2 1/4")	10-28775
34	WASHER, UPPER MOUNT COVER SCREWS	12-8M0204649
35	NUT, UPPER MOUNT COVER SCREWS	11-35888
36	BUMPER, RUBBER - MOUNTING SCREW	25067
37	SCREW, UPPER MOUNT (5 1/2")	10-75284
38	MOUNT, RUBBER - LOWER	30512
39	NUT, MOUNTING SCREW	11-25096
40	COVER, LOWER MOUNT - PORT SIDE	26336
40	COVER, LOWER MOUNT - STARBOARD SIDE	26337
41	SCREW, LOWER MOUNT COVER FASTENING	10-29256

FLYWHEEL ASSEMBLY AND STATOR

Below is the parts list for Mercury 800 (6 CYL.) FLYWHEEL ASSEMBLY AND STATOR:

Position No.	Part Name	OEM Number	Supersedes
1	NUT, FLYWHEEL	11-8M0214915
2	WASHER, FLYWHEEL NUT	12-26617
3	KEY, FLYWHEEL DRIVE	28-45554
4	FLYWHEEL ASSEMBLY	213-1683A4
5	FLANGE, FLYWHEEL PULLEY	29788
6	PULLEY, FLYWHEEL	30306
7	PIN, DOWEL - PULLEY TO FLYWHEEL	17-26618
8	HUB, FLYWHEEL PULLEY	29787
9	RATCHET, FLYWHEEL	50-30745
10	SCREW, RATCHET TO FLYWHEEL Comment: WHERE NO LOCKWASHER IS INCLUDED WITH 10-31208 SCREW, USE 13-26992 LOCKWASHER	10-29238
11	STATOR, ALTERNATOR	398-2035
12	TERMINAL, STATOR LEAD WIRE	30050
13	SCREW, STATOR TO UPPER END CAP	10-29283
14	CLIP, STATOR LEAD TO EXHAUST COVER	54-24836
15	"D" WASHER, CLIP FASTENING SCREW	8M0084613	69205
16	SCREW, STATOR LEAD CLIP FASTENING	10-8M0113176
17	"S" CLIP, STATOR LEAD TO BOTTOM COWL	54-22783

FUEL PUMP AND FUEL LINES

Below is the parts list for Mercury 800 (6 CYL.) FUEL PUMP AND FUEL LINES:

Position No.	Part Name	OEM Number	Supersedes
1	FUEL PUMP ASSEMBLY-UPPER	30269A2
2	GASKET, CHECK VALVE TO HOUSING	27-23005
3	VALVE, CHECK-FUEL PUMP	21-8M0082362	21-30430, 21-F177330, F84330-1
4	RETAINER, CHECK VALVE	23004
5	SCREW, RETAINER TO HOUSING	10-43725
6	GASKET, FUEL PUMP	27-24863
7	DIAPHRAGM,FUEL PUMP	23014
8	FUEL PUMP ASSEMBLY-LOWER	30461A2
2	GASKET, CHECK VALVE TO HOUSING	27-23005
3	VALVE, CHECK-FUEL PUMP	21-8M0082362	21-30430, 21-F177330, F84330-1
4	RETAINER,CHECK VALVE	23004
5	SCREW,RETAINER TO HOUSING	10-43725
6	GASKET, FUEL PUMP	27-24863
7	DIAPHRAGM, FUEL PUMP	23014
9	COVER, FUEL PUMP	30275
10	GASKET, FUEL PUMP COVER	27-30276
11	SCREW, FUEL PUMP MOUNTING (1 1/2")	10-29878
12	SCREW, FUEL PUMP MOUNTING (1 3/4")-UPPER MOUNTING	10-30274
13	SCREW, FUEL PUMP MOUNTING (1 7/8")-LOWER PUMP	10-30273
14	FUEL LINE,UPPER FUEL PUMP OUTLET TO UPPER CARBURETOR	32-30467
15	CONNECTOR, UPPER FUEL PUMP OUTLET	22-30468
16	SLEEVE, FUEL PUMP OUTLET CONNECTOR	22-30175
17	NUT, FUEL PUMP OUTLET CONNECTOR	22-30177
18	FUEL LINE, LOWER PUMP OUTLET TO UPPER PUMP INLET	32-17008
19	FUEL LINE, LOWER FUEL PUMP OUTLET TO LOWER CARBURETOR	32-30233
20	CONNECTOR, LOWER FUEL PUMP OUTLET	22-30468
21	SLEEVE, FUEL PUMP OUTLET CONNECTOR	22-30175
22	NUT, FUEL PUMP OUTLET CONNECTOR	22-30177
23	FUEL LINE, ADAPTOR TO LOWER FUEL PUMP INLET	32-30176
24	ELBOW, LOWER FUEL PUMP INLET	22-30174
25	SLEEVE, FUEL PUMP INLET ELBOW	22-30175
26	NUT, FUEL PUMP INLET ELBOW	22-30177
27	ADAPTOR, CHECK UNIT (FUEL LINE)	30186
28	STEM, CHECK UNIT ADAPTOR	30187
29	"O" RING, ADAPTOR STEM	25-16524
30	SPRING, ADAPTOR STEM	24-30189
31	CUP WASHER, ADAPTOR	30188
32	SCREW, ADAPTOR TO BOTTOM COWL	10-56500
33	NUT, ADAPTOR FASTENING SCREW	11-8M0207775
34	FUEL LINE, UPPER TO CENTER TO LOWER CARBURETOR	32-30230
35	TEE, CENTER AND LOWER CARBURETOR	22-25956
36	TEE, UPPER CARBURETOR	22-286241

GEAR HOUSING ASSEMBLY, COMPLETE

Below is the parts list for Mercury 800 (6 CYL.) GEAR HOUSING ASSEMBLY, COMPLETE:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, COMPLETE (SHORT SHAFT) Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	1623-2022A7
-	GEAR HOUSING ASSEMBLY, COMPLETE (LONG SHAFT Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	1623-2022A6
-	GEAR HOUSING ASSEMBLY, COMPLETE (SHORT SHAFT) Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	1623-2022A7
-	GEAR HOUSING ASSEMBLY, COMPLETE (LONG SHAFT) Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	1623-2022A6
1	GEAR HOUSING ASSEMBLY	1623-2041A2
54	CAM, SHIFT	760394
55	FOLLOWER, CAM	30625
56	SLIDE, CROSS PIN	30624
57	SPRING, COMPRESSION - CAM FOLLOWER	24-30622
58	SHIM, BEARING OUTER RACE TO GEAR HOUSING	15-30923A1
59	PIN, CROSS - RATCHET TO PROPELLER SHAFT	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
60	SPRING, RETAINING - CROSS PIN	24-30893
61	SHAFT, PROPELLER	44-47900A2
--	FORWARD GEAR ASSEMBLY, COMPLETE Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	43-30938A2
62	FORWARD GEAR ASSEMBLY, COMPLETE Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	43-30938A2
63	BEARING, ROLLER - FORWARD GEAR Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	31-30895T
64	TAPERED ROLLER BEARING ASSEMBLY Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	31-30894A1
65	CUP, TAPERED ROLLER BEARING Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	31-31092
66	RATCHET, SLIDING CLUTCH Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	52-30941
--	REVERSE GEAR ASSEMBLY, COMPLETE Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	43-30937
67	REVERSE GEAR ASSEMBLY	43-30937
68	BEARING, BALL - REVERSE GEAR Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	30-30548
69	SHIM, THRUST WASHER TO GEAR HOUSING Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	15-29955A1
70	WASHER, THRUST - BEARING CARRIER TO GEAR HOUSING Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	12-71143A1
--	FORWARD GREAR ASSEMBLY, COMPLETE Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	43-53100A3
62	FORWARD GEAR ASSEMBLY Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	43-53100A3
63	BEARING, ROLLER - FORWARD GEAR Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	31-30895T
64	TAPRERED ROLLER BEARING ASSEMBLY Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	31-30894A1
65	CUP, TAPERED ROLLER BEARING Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	31-31092
66	RATCHET, SLIDING CLUTCH Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	52-822539T	52-822539, 52-814756, 52-12777 USE ON ENGINES FROM SERIAL #1406323 AND UP
67	REVERSE GEAR ASSEMBLY Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	43-31887
68	BEARING, BALL - REVERSE GEAR Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	12-31262
69	SHIM, THRUST WASHER TO GEAR HOUSING Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	15-29955A1
70	WASHER, THRUST - BEARING CARRIER TO GEAR HOUSING Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	12-31797
71	"O" RING, BEARING CARRIER	25-29976
72	BEARING CARRIER ASSY (4 45/64" OVERALL LENGTH) Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	30579A1
72	BEARING CARRIER ASSY (4 5/8" OVERALL LENGTH) Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	31284T1
73	BEARING, ROLLER - BEARING CARRIER	31-30616
73A	BEARING, ROLLER - BEARING CARRIER	31-30956T
74	OIL SEAL, BEARING CARRIER	26-8M0204670
75	KEY, LOCATING - BEARING CARRIER	28-30281
76	WASHER, GEAR HOUSING COVER	12-29957
77	COVER, GEAR HOUSING	52699
78	WASHER, THRUST - BEARING CARRIER	12-31013
79	THRUST HUB AND WASHER ASSEMBLY	30581A1
80	WASHER, CUPPED - THRUST HUB	12-29590
81	PROPELLER ASSEMBLY, COMPLETE (2 BLADE - ALUMINUM)	48-65588A1
82	WASHER, SPLINED - PROPELLER SHAFT	12-30967
82	WASHER, SPLINED - PROPELLER SHAFT	12-31211Q03
83	TAB WASHER, PROPELLER NUT	14-30963
83	TAB WASHER, PROPELLER NUT	14-816629Q	14-816629, 14-31210, 14-816629B
84	NUT, PROPELLER	11-29594
85	SCREW, GEAR HOUSING TO DRIVE SHAFT HOUSING (1")	10-30206
86	WATER PICKUP, GEAR HOUSING	31237
87	GASKET, WATER PICKUP TO GEAR HOUSING	27-30557
88	SCREW, WATER PICKUP TO GEAR HOUSING (2 1/4")	10-30559
89	LOCKWASHER, WATER PICKUP FASTENING SCREW	13-8M0204647

GEAR HOUSING ASSEMBLY, COMPLETE (CONT)

Below is the parts list for Mercury 800 (6 CYL.) GEAR HOUSING ASSEMBLY, COMPLETE (CONT):

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, COMPLETE (SHORT SHAFT) Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	1623-2022A7
-	GEAR HOUSING ASSEMBLY, COMPLETE (LONG SHAFT) Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	1623-2022A6
-	GEAR HOUSING ASSEMBLY, COMPLETE (SHORT SHAFT) Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	1623-2022A7
-	GEAR HOUSING ASSEMBLY, COMPLETE (LONG SHAFT) Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	1623-2022A6
1	GEAR HOUSING ASSEMBLY	1623-2041A2
2	STUD, GEAR HOUSING TO DRIVE SHAFT HOUSING (3 15/16")	16-57921
3	STUD, GEAR HOUSING TO DRIVE SHAFT HOUSING (2")	16-8M0133358
4	STUD, WATER PUMP BASE AND BODY TO GEAR HOUSING (3 1/4")	16-30901
5	"O" RING, GEAR HOUSING STUD (16-30901)	25-62704
4	STUD, WATER PUMP BASE AN DBODY TO GEAR HOIUSING (3 1/4")	16-30669
6	STUD, WATER PUMP BASE AND BODY TO GEAR HOUSING (3 1/8")	16-306671
7	FITTING, GEAR HOUSING TO WATER INTAKE HOSE	22-30570
8	BEARING, ROLLER - DRIVE SHAFT	31-32898T
9	DRIVE SHAFT (SHORT SHAFT)	45-38459
9	DRIVE SHAFT (LONG SHAFT)	45-38460
10	GEAR, PINION - DRIVE SHAFT Comment: USE ON ENGINES FROM SERIAL #1406322 AND BELOW	43-30566
10	GEAR, PINION - DRIVE SHAFT Comment: USE ON ENGINES FROM SERIAL #1406323 AND UP	43-31419
11	NUT, PINION GEAR TO DRIVE SHAFT	11-30932
12	SHIM, DRIVE SHAFT BALL BEARING TO GEAR HOUSING	15-30278A1
13	BEARING, BALL - DRIVE SHAFT	30-63326T
14	RING, RETAINING - BALL BEARING	53-30726
15	"O" RING, ATER PUMP BASE	25-8M0204651
16	WATER PUMP BASE ASSEMBLY	46-31277A2
17	OIL SEAL, WATER PUMP BASE	26-94038
18	DOWEL PIN, WATER PUMP BASE TO BODY	17-29596T
19	GASKET, LOWER - WATER PUMP BASE TO FACE PLATE	27-8M0090319	27-85608 1
21	GASKET, FACE PLATE TO WATER PUMP BODY	27-858524	27-85609 1, 27-85609B 1
22	WATER PUMP BODY ASSEMBLY	46-31277A2
23	INSERT, WATER PUMP BODY	30915
24	OIL SEAL, WATER PUMP BODY	26-16977
25	IMPELLER, WATER PUMP	47-89984T4
26	PIN, IMPELLER DRIVE	17-8M0214994
27	SCREW, WATER PUMP BODY TO GEAR HOUSING (1/4")	10-30720
28	LOCKWASHER, WATER PUMP BODY FASTENING SCREW AND STUDS (1/4"	13-26992
29	NUT, WATER PUMP BODY FASTENING STUDS (1/4")	11-29598
30	LOCKWASHER, WATER PUMP BODY FASTENING STUDS (5/16")	13-8M0204647
31	NUT, WATER JPUMP BODY FASTENING STUD (5/16")	11-28770
32	RING, RUBBER - CENTRIFUGAL SLINGER (DRIVE SHAFT)	25-8M0214918
33	SEAL, RUBBER - WATER PUMP BODY	26-38970
34	SLEEVE, GUIDE - WATER INLET TUBE	23-29804T
35	"O" RING, UPPER - DRIVE SHAFT	25-8M0214919
36	FITTING, WATER PUMP BODY TO WATER INTAKE HOSE	22-30570
37	HOSE, WATER INTAKE-GEAR HOUSING	32-30556
38	CLAMP, WATER INTAKE HOSE TO FITTINGS	54-30558
39	SHAFT, SHIFT - LOWER	25136
40	CLIP, RETAINING - SHIFT SHAFT	53-29641
41	"O"RING, SHIFT SHAFT BUSHING	25-25439
42	BUSHING ASSEMBLY, SHIFT SHAFT	23-8M0112749
43	OIL SEAL, SHIFT SHAFT BUSHING	26-892361
44	WASHER, RUBBER - SHIFT SHAFT BUSHING	12-31266
45	CAM, LOWER - REVERSE LOCKING	52918
46	CAM, UPPER - REVERSE LOCKING	52919
47	SPACER, NYLON - REVERSE LOCKING CAM	23-30607
48	PLUG, PIPE - SHIFT SHAFT GREASE FILLER HOLE	22-390721
49	SCREW, GREASE FILLER AND VENT HOLE	10-79953Q04
50	WASHER GREASE FILLER AND VENT HOLE SCREW	12-191833
51	SCREW, GEAR HOUSING FLUSHING HOLE	10-29608
52	GASKET, GEAR HOUSING FLUSHING HOLE SCREW	27-8M0214916
53	SEAL, GEAR HOUSING FLUSHING HOLE	26-8M0214917

STARTER MOTOR, STARTER SOLENOID, RECTIFIER AND WIRING HARNES

Below is the parts list for Mercury 800 (6 CYL.) STARTER MOTOR, STARTER SOLENOID, RECTIFIER AND WIRING HARNES:

Position No.	Part Name	OEM Number	Supersedes
1	WIRING HARNESS, INTERNAL	30472
2	TERMINAL, HARNESS AND MERCURY SWITCH LEADS	30050
3	SPRING, GARTER-INTERNAL WIRING HARNESS	24-28975
4	PLATE, WIRING HARNESS TO BOTTOM COWL	26079A2
5	SCREW,HARNESS PLATE FASTENING	10-45893
6	"S" CLIP, RECTIFIER HARNESS LEAD TO BOTTOM COWL	54-22783
7	RECTIFIER ASSEMBLY	32177A2	29691
8	LOCKWASHER, RECTIFIER MOUNTING SCREW	13-8M0204647
9	NUT, RECTIFIER MOUNTING SCREW	11-21929
10	SLEEVE, RUBBER- RECTIFIER HARNESS LEAD	32-28052
11	SLEEVE, RUBBER-RECTIFIER STATOR LEAD	32-28373
12	SCREW, HARNESS AND STATOR LEADS TO RECTIFIER	10-35400
13	NUT, HARNESS AND STATOR LEADS FASTENING SCREW	11-8M0204718
14	STARTER MOTOR ASSEMBLY(BOSCH) Comment: THE 50-30575 STARTER MOTOR (BOSCH) USED ON EARLY PRODUCTION ENGINES IS NO LONGER AVAILABE, FOR REPLACEMENT, ORDER 50-30842 STARTER MOTOR (DELCO-REMY) AND COMPONENT PARTS.	50-30575
14A	STARTER MOTOR ASSEMBLY (DELCO-REMY)	50-30842
15	PLATE, SPACER-STARTER MOTOR- Comment: USE ONLY WITH 50-30842 STARTER MOTOR ON EARLY PRODUCTION ENGINES	31057
--	BUMPER, RUBBER-STARTER MOTOR DRIVE END PLATE Comment: USE ONLY WITH 50-30842 STARTER MOTOR ON EARLY PRODUCTION ENGINES	21098
--	WASHER, RUBBER-STARTER MOTOR DRIVE END PLATE Comment: USE ONLY WITH 50-30842 STARTER MOTOR ON EARLY PRODUCTION ENGINES	12-31364
16	SCREW, STARTER MOTOR TO CRANKCASE FLANGE	10-22698
17	LOCKWASHER, STARTER MOTOR FASTENING SCREW	13-8M0204647
18	BRACKET, SUPPORT-STARTER MOTOR	38747
19	WASHER, THRU BOLT-BRACKET TO STARTER MOTOR	12-24664
20	LOCKWASHER, THRU BOLT-BRACKET TO STARTER MOTOR	13-26992
21	NUT, THRU BOLT-BRACKET TO STARTER MOTOR	11-20890
22	CABLE,WIRE-STARTER TO STARTER SOLENOID	84-93389A12
23	CLAMP, LOWER CABLE-STARTER TO SOLENOID	54-20534
24	SCREW, WIRING HARNESS GROUND LEAD TO STARTER MOTOR	10-69035
25	SOLENOID, STARTER	32268
26	LOCKWASHER, SOLENOID TERMINAL (5/16)	13-8M0204647
27	NUT, SOLENOID TERMINAL (5/16)	11-22053
28	LOCKWASHER, SOLENOID TERMINAL	10,13-26996
29	NUT, SOLENOID TERMINAL	10,11-68219
30	SCREW< SOLENOID TO STARTER MOTOR	10-29238
31	CLAMP, WIRING HARNESS TO STARTER SUPPORT BRACKET	54-22627
32	"D" WASHER, HARNESS CLAMP	8M0084613	69205
33	SCREW, HARNESS CLAMP FASTENING	10-62568
34	BLOCK, TERMINAL-UPPER FUEL PUMP PAD	29714
35	SCREW, TERMINAL BLOCK FASTENING	10-22245
36	LOCKWASHER, TERMINAL BLOCK FASTENING SCREW	13-26996
37	WASHER, TERMINAL BLOCK FASTENING SCREW	12-26014
38	RESISTOR	393-1572
39	SNUBBER, RESISTOR TO TRANSFER PORT COVER SCREW	30449
40	SNUBBER, RESISTOR TO TRANSFER PORT COVER SCREW	30449
41	SCREW,RESISTOR, SNUBBER AND COVER MOUNTING (1 3/8")	10-24770
42	LOCKWASHER, RESISTOR, SNUBBER AND COVER MOUNTING SCREW	13-26992
43	WASHER, RESISTOR, SNUBBER AND COVER MOUNTING SCREW	12-69057
44	JUMPER, RESISTOR TO RESISTOR AND RESISTOR TO TERMINAL BLOCK	29112
45	JUMPER, RESISTOR TO TERMINAL BLOCK	30020
46	SCREW,JUMPER LEADS TO RESISTOR	10-46718
47	LOCKWASHER, JUMPER LEADS FASTENING SCREW	13-26995
48	WASHER, JUMPER LEADS FASTENING SCREW	12-30191
49	SCREW, HARNESS AND JUMPER LEADS TO TERMINAL BLOCK	10-35400
50	CLIP, WIRING HARNESS TO CRANKCASE FLANGE	26836
51	CLIP, WIRING HARNESS TO CYLINDER BLOCK COVER	54-24836
52	"D" WASHER, HARNESS CLIP	8M0084613	69205
53	SCREW, HARNESS CLIP FASTENING	10-8M0113176
54	TERMINAL BLOCK ASSEMBLY, EXHAUST COVER	29765A1
54A	TERMINAL BLOCK, EXHAUST COVER	30212
-	LABEL, TERMINAL BLOCK COLOR LEADS	37-30649
55	SWITCH, MERCURY	58124A1
56	CLAMP, MERCURY SWITCH	54-22875
57	"D" WASHER, CLAMP FASTENING SCREW	8M0084613	69205
58	SCREW, MERCURY SWITCH CLAMP TO EXHAUST COVER	10-20401
59	SCREW, HARNESS LEADS TO TERMINAL BLOCK	10-35400
59	SCREW, HARNESS LEADS TO TERMINAL BLOCK	10-72169
59	SCREW, HARNESS LEADS TO TERMINAL BLOCK	10-62568

TOP COWL AND STARTER ASSEMBLY

Below is the parts list for Mercury 800 (6 CYL.) TOP COWL AND STARTER ASSEMBLY:

Position No.	Part Name	OEM Number	Supersedes
1	TOP COWL ASSEMBLY Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	182-1809A2
2	STUD, FRONT - TOP COWL TO CRANKCASE Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	16-20353
3	GROMMET, CHOKE KNOB Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	25-20116
1	TOP COWL ASSEMBLY Comment: STARTED WITH SERIAL 1402844 ON MERC 800E AND WITH SERIAL 1404354 ON MERC 800EL.	182-1895A2
2	STUD, FRONT - TOP COWL TO CRANKCASE Comment: STARTED WITH SERIAL 1402844 ON MERC 800E AND WITH SERIAL 1404354 ON MERC 800EL.	16-20353
3	GROMMET, CHOKE KNOB Comment: STARTED WITH SERIAL 1402844 ON MERC 800E AND WITH SERIAL 1404354 ON MERC 800EL.	25-20116
-	DECAL, TOP COWL - STARBOARD SIDE Comment: STARTED WITH SERIAL 1402844 ON MERC 800E AND WITH SERIAL 1404354 ON MERC 800EL.	37-46023A1
-	DECAL, TOP COWL-PORT SIDE Comment: STARTED WITH SERIAL 1402844 ON MERC 800E AND WITH SERIAL 1404354 ON MERC 800EL.	37-46023A1
4	REVEAL, AIR INTAKE	31476
5	SCREW, REVEAL TO TOP COWL	10-37370
6	LOCKWASHER, REVEAL TO TOP COWL FASTENIING SCREW	13-26996
7	SCREEN, VENT - TOP COWL	31475
8	SCREW, VENT SCREEN TO TOP COWL	10-26668
9	PLATE ASSEMBLY - COWL MOUNTING	29981A1
10	STUD, REAR - TOP COWL TO COVER	16-20353
11	SCREW, PLATE ASSEMBLY TO TOP COWL	10-29282
11	SCREW, PLATE ASSEMBLY TO TOP COWL	10-28668
--	LETTERS, SET - STARBOARD Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	37-46023A1
12	LETTER "M" - STARBOARD Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29939M
13	LETTER "E" - STARBOARD Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29939E
14	LETTER "R" - STARBOARD Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29939R
15	LETTER "C" - STARBOARD Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29939C
16	LETTER "U" - STARBOARD Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29939U
17	LETTER "Y" - STARBOARD Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29939Y
--	LETTERS, SET - PORT Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	37-46023A1
12	LETTER "M" - PORT Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29940M
13	LETTER "E" - PORT Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29940E
14	LETTER "R" - PORT Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29940R
15	LETTER "C" - PORT Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29940C
16	LETTER "U" - PORT Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29940U
17	LETTER "Y" - PORT Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	29940Y
18	FASTENER, LETTER TO TOP COWL Comment: USE THRU SERIAL #1402843 ON MERC 800E AND THRU SERIAL #1404353 ON MERC 800EL.	53-30022
19	WASHER, TOP COWL STUD (1/16")	12-20028
20	WASHER, TOP COWL STUD (3/4" OD)	12-69057
21	WASHER, TOP COWL STUD (1/32")	12-20583
22	NUT, TOP COWL FASTENING	11-8267089
23	RETAINER, STARTER SPRING	30755
24	SPRING, STARTER REWING	24-30753
25	BUSHING, SPRING GUIDE	23-30754
26	SHEAVE ASSEMBLY	50-30749
27	PAWL, STARTER	20162
28	WASHER, WAVE - STARTER PAWL	13-29402
29	BUSHING, NYLON - SHEAVE SHAFT SPACER	23-30752
30	SPACER, SHEAVE SHAFT	23-30759
31	WASHER, SHEAVE SHAFT TO STARTER SHEAVE	12-26180
32	WASHER, WAVE - WASHER TENSION	13-20160
33	WASHER, EQUALIZING RING - STARTER SHEAVE	12-30758
34	PLATE, RETAINER - STARTER PAWL	30757
35	SHAFT, SHEAVE	30756
36	TAB WASHER, SHEAVE SHAFT NUT	14-20165
37	NUT, SHEAVE SHAFT (LEFT HAND THREAD)	11-20166
38	STARTER CABLE ASSEMBLY	50-12066Q10
39	HANDLE, STARTER CABLE	28747
40	RETAIINER, STARTER CABLE AND HANDLE	79470A1
41	PLATE, ROPE GUIDE	30045
42	SCREW, DRIVE, ROPE GUIDE PLATE TO TOP COWL	10-28642
43	HANDLE, CHROME - TOP COWL	31463
44	HANDLE ASSEMBLY, INSIDE - TOP COWL	31487
45	PAD, BUMPER - TOP COWL HANDLE	30896
46	WASHER, CHROME HANDLE TO INSIDE HANDLE STUD	12-8M0204649
47	NUT, CHROME HANDLE TO INSIDE HANDLE FASTENING	11-826709109	11-33825, 11-35045
48	SCREW, FRONT - HANDLE TO TOP COWL (1")	10-29199
49	NUT, HANDLE TO TOP COWL STUD	11-826709109	11-33825, 11-35045
50	TRIM MOULDING ASSEMBLY - TOP COWL	29980A1
51	SCREW, DECORATIVE - MOULDING TO TOP COWL	10-29226
52	SCREW, BRASS - MOULDING TO TOP COWL	10-29227
53	LOCKWASHER, MOULDING FASTENING SCREW	13-26995
54	NUT, MOULDING FASTENING SCREW	11-26419

Download this page as PDF: Click here

For Mercury Owners:

To assist you in maintaining and repairing your marine engines, we hope the following resources may be of use:

Mercury / Mercruiser / Mariner Parts from JLM Marine

About JLM Marine

Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.

As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.

We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.