Mercury 75 (3 CYL.) (0C222000 THRU 0D283221) Outboard Motor Parts Diagram & Catalog – Free PDF Download
30 Apr 2025
0 Comments
Attenuator Plate
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Attenuator Plate:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | COVER | 42969A3 | |
| 2 | SCREW, (#10-16 x .625) | 10-48409 | |
| 3 | ATTENUATOR PLATE | 42970A2 | |
| 4 | WASHER | 12-4002217 | |
| 5 | NUT, Carburetor Studs | 11-826365 | |
| 6 | CUP | 39519 | |
| 7 | LATCH | 98889 | |
| 8 | SCREW, Drive | 10-42975 | |
| 9 | SPRING, Handle, Old Design | 24-44297 | |
| 10 | PLUG, Handle, Old Design | 19-32298 | |
| 11 | GASKET | 27-151724 | |
| 12 | CABLE TIE, (8.00 Inch) Comment: (As Required) | 54-816311T | 54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275 (As Required) |
| 13 | HOSE, (26.00 Inches Bulk) | 32-9912878 | |
| 14 | LINK ROD | 8M0084744 | |
| 15 | ARM ASSEMBLY | 11399A1 | |
| 16 | SCREW, (M5 x 6) | 10-40056103 | |
| 17 | WASHER, (.203 x .500 x .032) | 12-8M0204666 | |
| 18 | ROLLER | 67748 | |
| 19 | LINK | 98886T01 | |
| 20 | THROTTLE LINK | 98887T | |
| 21 | SCREW, (#10-16 x .625) | 10-48409 | |
| 22 | WASHER, (.203 x .500 x .032) | 12-8M0204666 |
Carburetor
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Carburetor:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | CARBURETOR, Top, 75 - WME-17 | 3301-9012A71 | |
| 1 | CARBURETOR, Center, 75 - WME-17 | 3301-9012A72 | |
| 1 | CARBURETOR, Bottom, 75 - WME-17 | 3301-9012A73 | |
| 1 | CARBURETOR, Top, 75 COMM. - WME-18 | 3301-9012A58 | |
| 1 | CARBURETOR, Center, 75 COMM. - WME-18 | 3301-9012A59 | |
| 1 | CARBURETOR, Bottom, 75 COMM. - WME-18 | 3301-9012A60 | |
| 1 | CARBURETOR, Top, 90 - WME-19 | 3301-9012A64 | |
| 1 | CARBURETOR, Center, 90 - WME-19 | 3301-9012A65 | |
| 1 | CARBURETOR, Bottom, 90 - WME-19 | 3301-9012A66 | |
| 1 | CARBURETOR, Top, 75 COMM. - WME-25 | 3301-9012A74 | |
| 1 | CARBURETOR, Center, 75 COMM. - WME-25 | 3301-9012A75 | |
| 1 | CARBURETOR, Bottom, 75 COMM. - WME-25 | 3301-9012A76 | |
| 2 | NOT SOLD SEPARATE, Gasket, Fuel Bowl | NSS | |
| 3 | NOT SOLD SEPARATE, Retaining Ring | NSS | |
| 4 | FUEL BOWL, Upper | 1395-811696 | 1395-9589 |
| 4 | FUEL BOWL, Center, Lower | 1395-811693 | 1395-9590 |
| 4 | FUEL BOWL, Upper | 1395-811696 | 1395-9589 |
| 4 | FUEL BOWL, Center, Lower | 1395-811693 | 1395-9590 |
| 5 | THROTTLE SHAFT, Upper, Lower | 1395-9591 | |
| 6 | THROTTLE SHAFT, Center | 19270 | |
| 7 | THROTTLE VALVE, 75/75 COMM. | 1395-9593 | |
| 7 | THROTTLE VALVE, 90 | 1395-811216 | 814678 |
| 8 | FLOAT | 1395-9594 | |
| 9 | NOT SOLD SEPARATE, Float Shaft | NSS | |
| 10 | INLET NEEDLE VALVE | 1395-879194011 | 1395-9595 |
| 11 | PLUG | 1395-811694 | 1395-9596 1 |
| 11 | PLUG KIT, WME-25 | 1395-811694 | 1395-9596 1 |
| 12 | NOT SOLD SEPARATE, Gasket | NSS | |
| 13 | NOT SOLD SEPARATE, Gasket, Cover Plate | NSS | |
| 14 | GASKET, Flange | 27-151724 | |
| 15 | NOT SOLD SEPARATE, Screw, Throttle Valve | NSS | |
| 16 | SCREW, Cover Plate, WME-8/9/15 | 1395-9597 | |
| 16 | SCREW, Cover Plate, WME-17/18/19/25 | 1395-811220 | |
| 17 | SCREW, Fuel Bowl | 1395-808612 | 1399-5132 |
| 18 | COVER PLATE, WME-8/9/15 | 1395-9598 | |
| 18 | COVER PLATE, WME-17/18/19/25 | 1395-811221 | |
| 19 | JET, (.064), Main Fuel,75 COMM. | 1399-4216 | |
| 19 | JET, (.068), Main Fuel, 75 | 1395-6029 | |
| 19 | MAIN FUEL JET, (.066), Main Fuel, 90 | 1399-4215 | |
| 20 | JET, Vent, .094 | 1395-8423 | |
| 21 | NOT SOLD SEPARATE, Gasket, Nozzle Well | NSS | |
| 22 | NOT SOLD SEPARATE, Spring, Idle Needle | NSS | |
| 23 | NOT SOLD SEPARATE, Spring, Throttle Return | NSS | |
| 24 | NOT SOLD SEPARATE, Spring, Idle Air | NSS | |
| 25 | NOT SOLD SEPARATE, Idle Needle | NSS | |
| 26 | NOT SOLD SEPARATE, Idle Air Needle | NSS | |
| -- | REPAIR KIT | 1395-8236354 | |
| -- | CARB GASKET SET | 1395-8112231 |
Co-Pilot
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Co-Pilot:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | CO-PILOT ASSEMBLY | 56-52148A7 | |
| 1 | PILOT ROD | 52148 | |
| 2 | NUT ASSEMBLY | 11-52155A1 | |
| 3 | SCREW, (.250-28 x 1.380) | 10-36154 | |
| 4 | WING NUT | 11-52152 | |
| 5 | ROD | 873491 | |
| 6 | BUSHING | 23-521512 | |
| 7 | WASHER, (.328 x .625 x .060) | 12-20722 | |
| 8 | NUT, (.312-24) | 11-826709111 | 11-45592 |
| 9 | WASHER, (.328 x .625 x .060) | 12-20722 | |
| 10 | NUT, (.312-24) | 11-826709111 | 11-45592 |
Cowl Mounting Brackets
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Cowl Mounting Brackets:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | BRACKET ASSEMBLY, Black | 42965A1 | |
| 1 | BRACKET ASSEMBLY, Gray | 42965A2 | |
| 2 | SEAL | 183061 | |
| 3 | SEAL | 42935 | |
| 4 | RESTRAINT | 42908 | |
| 5 | SCREW, (M5 x 10) | 10-400015 | |
| 6 | WASHER | 12-42118 | |
| 7 | CONNECTOR | 42907 | |
| 8 | TUBING, Tell Tale | 32-8M0108349 | 32-8M0047448, 32-830757130, 32-830757 80 |
| 9 | CABLE TIE, (8.00 Inch) | 54-816311T | 54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275 |
| 10 | HOUSING | 932642 | |
| 11 | SCREW | 10-8M0103817 | |
| 12 | WASHER Comment: (Cylinder Block Cover Casting Number 1034-8998C) | 12-814803 | 12-93853 (Cylinder Block Cover Casting Number 1034-8998C) |
| 13 | WASHER, (.344 x .688 x .065) Comment: (Cylinder Block Cover Casting Number 1034-8998C) | 12-8M0204690 | |
| 14 | BUSHING Comment: (Cylinder Block Cover Casting Number 1034-8998C) | 23-14395 | |
| 12 | WASHER, (.344 x 1.00 x .063) Comment: (Cylinder Block Cover Casting Number 1034-8998C1) | 12-817274 | 12-817274 1 (Cylinder Block Cover Casting Number 1034-8998C1) |
| 14 | BUSHING Comment: (Cylinder Block Cover Casting Number 1034-8998C1) | 23-143951 | |
| 15 | GROMMET | 25-88033 | |
| 16 | SCREW, (M5 x 30) | 10-400038 | |
| 17 | WASHER | 12-42118 | |
| 18 | BRACKET, Front, Black | 42952T | |
| 18 | BRACKET, Front, Gray | 42952T6 | |
| 19 | SEAL | 67260 | |
| 20 | GROMMET | 25-67272 | |
| 21 | RETAINER | 99447 | |
| 22 | SCREW, (10-32 X 1.00) | 10-69011 | |
| 23 | SCREW, (M8 x 35) | 10-40011151 | |
| 24 | WASHER, (.344 x 1.00 x .063) | 12-817274 | 12-817274 1 |
| 25 | GROMMET | 25-88033 | |
| 26 | BUSHING | 23-143951 |
Cowls and Front Cover
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Cowls and Front Cover:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | COWL ASSEMBLY, Port, Black | 2188-9006A2 | |
| 1 | COWL ASSEMBLY, Port, Gray | 2188-9006A3 | |
| 2 | SEAL | 429404 | |
| 3 | SEAL, Rear | 12401 | |
| 4 | SEAL | 90274 | |
| 5 | SHIELD | 42958 | |
| 6 | SCREW, (#10-16 x .625) | 10-48409 | |
| 7 | WASHER, (.203 x .406 x .040) | 12-89302 | |
| 8 | SOUND BLANKET | 435331 | |
| 9 | SEAL, (4.20 Inch) | 193682 | |
| 10 | COWL ASSEMBLY, Starboard, Black | 2187-9070A4 | |
| 10 | COWL ASSEMBLY, Starboard, Gray | 2187-9070A5 | |
| 11 | OIL LEVEL GAUGE ASSEMBLY | 11315A1 | |
| 12 | NUT | 11-65110 | |
| 13 | RETAINER | 113171 | |
| 14 | WASHER, (.203 x .406 x .040) | 12-89302 | |
| 15 | SOUND BLANKET | 435342 | |
| 16 | SEAL, (4.20 Inch) | 193682 | |
| 17 | GROMMET | 42905 | |
| 18 | PLUG, Handle Models | 812431 | |
| 19 | SEAL | 26-60297 | |
| 20 | SHIELD | 42957 | |
| 21 | SCREW, (#10-16 x .625) | 10-48409 | |
| 22 | COVER ASSEMBLY MERCURY, Black | 43138A2 | |
| 22 | COVER ASSEMBLY MARINER, Gray | 43138A3 | |
| 23 | BUMPER | 12356 | |
| 24 | SPRING | 24-17288 | |
| 25 | BRACKET ASSEMBLY | 43137A1 | |
| 26 | SPEED NUT | 11-434181 | |
| 27 | RETAINER | 15432 | |
| 28 | PIN | 17-43134 | |
| 29 | SCREW, (#10-16 x .625) | 10-48409 | |
| 30 | WASHER, (.344 x .688 x .065) | 12-8M0204690 | |
| 31 | BRACKET, Lower | 879851 | |
| 32 | BRACKET, Upper | 879871 | |
| 33 | SCREW, (M8 x 25) | 10-4010725 | |
| 34 | COWL LATCH | 120811 | |
| 35 | SCREW, (#10-16 x .625) | 10-48409 | |
| 36 | EMERGENCY STARTER ROPE, Manual Starting | 47341A11 |
Crankshaft, Pistons And Connecting Rods (#638-8532-1)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Crankshaft, Pistons And Connecting Rods (#638-8532-1):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | CRANKSHAFT ASSEMBLY | 472-9001T3 | |
| 2 | BALL BEARING, Lower | 30-43011T | |
| 3 | RETAINING RING, Old Design | 53-93412 | |
| 4 | O-RING | 25-35126 | |
| 4A | WEAR SLEEVE | 786611 | |
| 5 | RING ASSEMBLY | 39-42079A4 | |
| 6 | KEY, Woodruff | 28-91800 | |
| 7 | DRIVER GEAR | 43-43019A1 | |
| 8 | ROLLER BEARING ASSEMBLY, Upper | 31-43013T3 | |
| 9 | SEAL, Oil | 26-8M0214932 | |
| 10 | O-RING | 25-823683 | 25-64067 |
| 11 | ROLLER BEARING ASSEMBLY | 42943A1 | |
| 12 | PISTON ASSEMBLY Comment: (Standard) | 777-9009T13 | |
| 12 | PISTON ASSEMBLY Comment: (.015 Oversize) | 777-9009A6 | |
| 12 | PISTON ASSEMBLY Comment: (.030 Oversize) | 777-9009A7 | |
| 13 | RING | 53-857196 | 40-52035 |
| 14 | PISTON RING ASSEBMLY Comment: (Standard) | 39-96170A12 | |
| 14 | PISTON RING ASSEMBLY Comment: (.015 Oversize) | 39-96170A3 | |
| 14 | PISTON RING ASSEMBLY Comment: (.030 Oversize) | 39-96170A4 | |
| 15 | CONNECTING ROD ASSEMBLY | 638-9002A6 | |
| 16 | WASHER | 12-8M0032839 | 12-47247 |
| 17 | NEEDLE, Roller Bearing | 29-8M0204715 | |
| 18 | SCREW, (.375-24 x 1.250) | 10-94320 | |
| 19 | BEARING/CAGE KIT | 31-844338A01 | 31-43012A04 |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 | 13589T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 Commercial | 13600T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 90 | 15081T96 |
Crankshaft, Pistons And Connecting Rods (#646-818846)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Crankshaft, Pistons And Connecting Rods (#646-818846):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | CRANKSHAFT ASSEMBLY | 472-9001T3 | |
| 2 | BALL BEARING, Lower | 30-43011T | |
| 3 | WEAR SLEEVE | 786611 | |
| 4 | O-RING | 25-35126 | |
| 5 | RING ASSEMBLY | 39-818412A4 | |
| 6 | KEY, Woodruff | 28-91800 | |
| 7 | DRIVER GEAR | 43-43019A1 | |
| 8 | ROLLER BEARING ASSEMBLY, Upper | 31-43013T3 | |
| 9 | SEAL, Oil | 26-8M0214932 | |
| 10 | O-RING | 25-823683 | 25-64067 |
| 11 | ROLLER BEARING ASSEMBLY | 42943A1 | |
| 12 | PISTON ASSEMBLY, Standard | 777-815965T4 | |
| 12 | PISTON ASSEMBLY (.015 Oversize) Comment: (As Required) | 777-815965A5 | |
| 12 | PISTON ASSEMBLY (.030 Oversize) Comment: (As Required) | 777-815965A6 | |
| 13 | RING | 53-857196 | 40-52035 |
| 14 | PISTON RING ASSEBMLY, Standard | 39-96170A12 | |
| 14 | PISTON RING ASSEMBLY (.015 Oversize) Comment: (As Required) | 39-96170A3 | |
| 14 | PISTON RING ASSEMBLY (.030 Oversize) Comment: (As Required) | 39-96170A4 | |
| 15 | CONNECTING ROD ASSEMBLY | 646-818846T6 | |
| 16 | WASHER | 12-8M0012298 | 12-812876 |
| 17 | NEEDLE BEARING | 29-8M0214954 | |
| 18 | SCREW, (.375-24 x 1.250) | 10-94320 | |
| 19 | ROLLER BEARING ASSEMBLY | 31-844338A01 | 31-43012A04 |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 | 13589T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 Commercial | 13600T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 90 | 15081T96 |
Cylinder Block And Crankcase
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Cylinder Block And Crankcase:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | CYLINDER BLOCK, 75 | 876-8947T49 | |
| 1 | CYLINDER BLOCK, 75 Work | 876-8947T50 | |
| 1 | CYLINDER BLOCK, 90 | 876-8947T51 | |
| 2 | SCREW, (M10 x 80) | 10-4009680 | |
| 2 | SCREW, (M8 x 80) | 10-81742780 | |
| 3 | PIN, Bearing Race | 17-8M0036405 | 17-67296 |
| 4 | PIN, Dowel | 17-43044 | |
| 5 | COVER, Top | 428841 | |
| 6 | COVER, Bottom | 76867 | |
| 7 | SCREW, (M8 x 50) | 10-81742750 | |
| 8 | CARRIER, Use Where Applicable | 65848 | |
| 9 | GROMMET, Use Where Applicable | 25-64872 | |
| 10 | CARRIER ASSEMBLY | 813801A1 | |
| 11 | CHECK VALVE | 21-42657A3 | |
| 12 | NUT, (M6) | 11-400212 | |
| 13 | CAP | 42942 | |
| 14 | CHECK VALVE, Press In | 21-426233 | |
| 15 | SCREW | 16-821676A1 | |
| 16 | ADJUSTING SCREW, (M6 x 55) | 10-814776 | 10-42978 |
| 17 | SCREW, (M8 x 35) | 10-82127335 | |
| 18 | COVER | 1034-9003A2 | |
| 19 | GASKET | 27-430057 | |
| 20 | SCREW, (M8 x 35) | 10-82127335 | |
| 21 | CLAMP | 54-814634 | |
| 22 | TEMPERATURE SENDER, (19.50 Inch) | 78799 | |
| 23 | RETAINER | 44290T | |
| 24 | SCREW, (#10-16 x .625) | 10-48409 | |
| 25 | WASHER, (.203 x .500 x .032) | 12-8M0204666 | |
| 26 | POPPET VALVE, Spring Length Is 2.00 Inch | 86596 | |
| 27 | SPRING, Spring Length Is 2.00 Inch | 24-42996 | |
| 26 | POPPET VALVE, Spring Length Is 3.00 Inch | 86596T | |
| 27 | SPRING, Spring Length Is 3.00 Inch | 24-42996 | |
| 28 | WASHER | 12-94182 | |
| 29 | SCREW, (#10-16 x .750) | 10-69570 | |
| 30 | DIAPHRAGM | 648771 | |
| 31 | THERMOSTAT, 143 Degrees | 75692 | |
| 31 | THERMOSTAT, 120 Degrees | 14586 | |
| 32 | GASKET | 27-8M0204714 | |
| 33 | GASKET | 27-430068 | |
| 34 | COVER | 8M0047619 | 884297, 42885 3 |
| 35 | SCREW, (M8 x 35) | 10-82127335 | |
| 36 | COVER, Non Oil Injection | 12621 | |
| 37 | GASKET, Non Oil Injection | 27-126201 | |
| 38 | SCREW, (M5 X 13), Non Oil Injection | 10-40007106 | |
| 39 | WASHER | 12-4002314 | |
| 40 | OIL WARNING MODULE | 14857A16 | |
| 41 | SCREW, (M6 x 30) | 10-4010630 | |
| 42 | PLUG, Pipe (.125-27) | 22-328022 | |
| 43 | TUBING, (20.00 Feet Bulk) | 32-892024122 | 32-99130122 |
| 44 | BOOT, Non Oil Injection | 99162001 | |
| - | GASKET SET | 27-43004A99 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 | 13589T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 Commercial | 13600T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 90 | 15081T96 |
Drive Shaft Housing
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Drive Shaft Housing:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | DRIVE SHAFT HOUSING ASSEMBLY, Black | 1598-8974T23 | |
| 1 | DRIVE SHAFT HOUSING ASSEMBLY, Gray | 1598-8974T23 | |
| 2 | STUD, (M10 x 100) | 16-903501 | |
| 3 | SCREW, (M10 x 45) | 10-4000380 | |
| 4 | PLUG, Three Ram Power Trim | 429221 | |
| 5 | WASHER | 12-45176 | |
| 6 | NUT, (M10) | 11-40140 | |
| 7 | GUIDE, Non PowerTrim | 429222 | |
| 8 | SPEEDOMETER PICK-UP ASSEMBLY | 22-85822A4 | |
| 9 | CONNECTOR, 90 Degree | 22-433351 | |
| 10 | CONNECTOR, Straight | 22-85822T | |
| 11 | REVERSE HOOK ASSEMBLY | 14664A2 | |
| 12 | PUSH ROD | 16686 | |
| 13 | SHAFT | 99606 | |
| 14 | COTTER PIN | 18-45882 | |
| 15 | BUSHING | 23-69132 | |
| 16 | SPRING | 24-996261 | |
| 17 | COTTER PIN | 18-47959 | |
| 18 | WASHER, (.323 x .563 x .063) | 12-8M0042642 | 12-70132 |
| 19 | SPRING | 24-16733 | |
| 20 | YOKE | 996361 | |
| 21 | NUT, (.312-24) | 11-82670911 | |
| 22 | CLEVIS PIN | 17-99663 | |
| 23 | COTTER PIN | 18-25191 | |
| 24 | MOUNT | 42930A1 | |
| 25 | BOLT, (M12 x 154) | 10-898835001 | 10-42973 |
| 26 | COVER | 100-8M4500752 | 8M0001130, 67077T |
| 26 | COVER | 67077F1 | |
| 27 | SCREW, (#12-24 x .620) | 10-88417 | |
| 28 | WASHER, (.875 Inch Outside Diameter) | 12-30119 | |
| 29 | NUT, (M12) | 11-8M0204662 | |
| 30 | GROUND WIRE ASSEMBLY | 88238A10 | |
| 31 | SCREW, (.250-20 x .500) | 10-41508 | |
| 32 | CLAMP | 8M0036730 | 93192 |
| 33 | NUT | 11-35521 | |
| 34 | SCREW, (M8 x 25) | 10-40011149 |
Electrical Components
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Electrical Components:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | IGNITION PLATE | 42968A23 | |
| 2 | SWITCH BOX | 332-7778A12 | |
| 3 | SCREW, (#10-16 x .440) | 10-69079 | |
| 4 | SCREW, (M5 X 30) | 10-40007110 | |
| 5 | SPACER | 23-94304 | |
| 6 | NUT, | 10-32,11-45076 | |
| 7 | HARNESS ASSEMBLY | 84-41592A4 | |
| 8 | CABLE | 84-813715A7 | |
| 9 | BOOT KIT | 85-63709A1 | |
| 10 | SPARK PLUG Comment: (NGK #BUHW-2) | 33-896329833 | 33-833C (NGK #BUHW-2) |
| 10 | SPARK PLUG Comment: (Belgium/Canada) (NGK #BUZHW-2) | 33-14103Q | |
| 11 | SCREW, (M8 x 25) | 10-82155025 | |
| 12 | IGNITION COIL ASSEMBLY | 339-832757A4 | |
| 13 | NUT, | 10-32,11-45076 | |
| 14 | COVER | 43542 | |
| 15 | SCREW, (M5 X 55) | 10-40007115 | |
| 16 | WASHER, (.203 x .406 x .040) | 12-89302 | |
| 17 | TERMINAL BLOCK, Black | 17602A1 | |
| 17 | TERMINAL BLOCK, Gray | 17602T02 | |
| 18 | SCREW, (M5 x 16) | 10-40056107 | |
| 19 | NUT, | 10-32,11-45076 | |
| 20 | MERCURY SWITCH, Old Design | 16731T01 | |
| 21 | SCREW, (M5 x 16) | 10-40056107 | |
| 22 | TERMINAL BLOCK | 86-45915 | |
| 23 | SCREW, (#10-16 x .500) | 10-48408 | |
| 24 | ENGINE HARNESS Comment: SN# D252461 & Up | 84-41591A7 | |
| 24 | WIRING HARNESS ASSEMBLY Comment: SN# D252460 & Below | 84-41591A3 | |
| 24 | ENGINE HARNESS, Use Without Reference Number 20 And 21 | 84-41591A7 | |
| 25 | FUSE, (20 Ampere) | 88-8M0207796 | |
| 26 | BATTERY CABLE, Positive | 84-88439A3 | |
| 26 | BATTERY CABLE, Negative | 84-88439A4 | |
| 27 | STARTER SOLENOID, ( 8-32 .250-20 Terminals) | 89-8M0185146 | |
| 27A | GROMMET | 25-818967 | |
| 27B | BUSHING | 23-8M0214955 | |
| 28 | SCREW, (M5 x 25) | 10-40011109 | |
| 29 | WASHER | 12-4002314 | |
| 30 | WIRE, (3.50 Inches) Black, Quantity Of Three On Power Trim | 84-88807A6 | |
| 31 | LOCKWASHER, (.250) | 13-26992 | |
| 32 | NUT, ( #8-32) | 11-64015 | |
| 33 | NUT, | 8-32,11-26419 | |
| 34 | FUSE HOLDER, Old Design | 134731 | |
| 35 | COVER | 124174 | |
| 36 | SCREW, (50 MM) | 10-40007114 | |
| 37 | WASHER, (.203 x .406 x .040), Use Where Applicable | 12-89302 | |
| 41 | HARNESS ASSEMBLY Comment: (Use With Black Terminal Block) | 84-12201A2 | |
| 42 | VOLTAGE REGULATOR Comment: (Use With Black Terminal Block) | 815279A2 | |
| 43 | SCREW, (M6 x 30) Comment: (Use With Black Terminal Block) | 10-4010630 | |
| 44 | VOLTAGE REGULATOR Comment: (Two Female/Three Male Terminals) | 8M0084173 | 883072T, 854515T 1 (Two Female/Three Male Terminals) |
| 44 | VOLTAGE REGULATOR, Five Ring Terminals | 815279A2 | |
| 45 | SCREW, (M6 x 35) | 10-4010635 | |
| 46 | HARNESS Comment: (Use With 815279--3 Voltage Regulator) | 84-821546A3 |
Exhaust Plate
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Exhaust Plate:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | PLATE ASSEMBLY, Exhaust | 42954A3 | |
| 2 | PIN, Dowel | 17-23784 | |
| 3 | SEAL | 42939 | |
| 4 | MOUNT, (2.375 Inch) | 8M0021331 | 881901, 42949 2 |
| 5 | SCREW, (M8 x 50) | 10-4010750 | |
| 6 | BOLT, (M12 x 175) | 10-898487 | 10-42974 |
| 6 | SCREW, Handle Models | 10-12515 | |
| 7 | WASHER | 12-32834 | |
| 8 | WASHER | 12-8M0204648 | |
| 9 | NUT | 11-896963 | 11-859129, 11-90099 |
| 10 | ELBOW | 22-996642 | |
| 11 | SCREW, (M8 x 35) | 10-40011151 | |
| 11 | SCREW, (M8 x 70) | 10-40011158 | |
| 12 | GASKET | 27-430086 | |
| 13 | EXHAUST TUBE | 8141281 | |
| 14 | SCREW, (M8 x 35) | 10-40011151 | |
| 15 | SEAL | 8M0039075 | 42962 |
| 16 | WATER TUBE | 32-430141 | |
| 17 | CLAMP | 99019 | |
| 18 | SEAL, Water Tube, Upper | 42941001 | |
| 19 | SCREW, (M8 x 50) | 10-4010750 | |
| 20 | GROMMET | 25-93221002 | |
| 21 | BRACKET ASSEMBLY, Lower, Black | 42953A2 | |
| 21 | BRACKET ASSEMBLY, Lower, Gray | 42953A3 | |
| 22 | SEAL | 43405 | |
| 23 | SCREW, (M8 x 50) | 10-81742750 | |
| 24 | BUSHING | 23-48237 | |
| 25 | SHIFT SHAFT ASSEMBLY, Upper | 79932A9 | |
| 26 | SHIFT LINK | 42912A1 | |
| 27 | BUSHING, Double Flange | 23-48475 | |
| 27 | BUSHING, Single Flange | 23-42994 | |
| 28 | WASHER, Wave Comment: (Use With Single Flange Bushing) | 13-29720 | |
| 29 | WASHER Comment: (Use With Single Flange Bushing) | 12-24664 | |
| 30 | NUT, (M6) | 11-401386 | |
| 31 | SPACER | 23-813745 | 23-43041 |
| 32 | COUPLING, Non Power Trim | 43053 | |
| 33 | COUPLING, Power Trim | 43585 | |
| 34 | GROMMET, Old Design | 25-8M0179867 |
Flywheel And Starter Motor
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Flywheel And Starter Motor:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | PLUG, Yellow, Flywheel | 19-45907 | |
| 2 | COVER ASSEMBLY | 42956A1 | |
| 3 | MARKER | 79022 | |
| 4 | SCREW, (.190-32 x .380) | 10-37572 | |
| 5 | WASHER | 12-72761 | |
| 6 | NUT, (M16 x 1.5) | 11-42979 | |
| 7 | WASHER | 12-33001 | |
| 8 | FLYWHEEL ASSEMBLY | 261-859234T30 | 261-859234T15, 261-878226T12, 261-859234T14, 261-9008A16 |
| 9 | STATOR ASSEMBLY | 398-832075A5 | |
| 10 | SCREW, (M5 x 25) | 10-4007325 | |
| 11 | TRIGGER ASSEMBLY | 99021A3 | |
| 12 | STARTER MOTOR | 50-893891T | 50-66015T 1 |
| 13 | COLLAR | 23-8M0034918 | 23-8M0001391, 56703 |
| 14 | STOP | 8M0043376 | 68042 |
| 15 | CABLE ASSEMBLY, Black | 84-93388A1 | |
| 16 | SCREW AND LOCKWASHER, (.250-20 x .625) | 10-69035 | |
| 17 | WIRE, Black | 84-88439A20 | |
| 17 | WIRE, Yellow | 84-93388A6 | |
| 18 | LOCKWASHER, (.250) | 13-26992 | |
| 19 | NUT, ( #8-32) | 11-64015 |
Fuel Pump(Use With 90 Degree Ceck Valve)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Fuel Pump(Use With 90 Degree Ceck Valve):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | FUEL PUMP ASSEMBLY | 14360A78 | |
| 2 | DIAPHRAGM KIT | 42909A4 | |
| 3 | NOT SOLD SEPARATE, Check Valve | NSS | |
| 4 | NOT SOLD SEPARATE, Gasket | NSS | |
| 5 | NOT SOLD SEPARATE, Diaphragm | NSS | |
| 6 | NOT SOLD SEPARATE, Gasket | NSS | |
| 7 | NOT SOLD SEPARATE, Spring | NSS | |
| 8 | NOT SOLD SEPARATE, Cap | NSS | |
| 9 | NOT SOLD SEPARATE, Check Valve | NSS | |
| 10 | NOT SOLD SEPARATE, Retainer | NSS | |
| 11 | NOT SOLD SEPARATE, Spring | NSS | |
| 12 | NOT SOLD SEPARATE, Cap | NSS | |
| 13 | GASKET | 27-8M0204705 | |
| 14 | BASE | 98768 | |
| 15 | PLATE | 98775A1 | |
| 16 | CHECK VALVE, Oil Injection | 21-424811 | |
| 17 | FITTING | 22-19688 | |
| 18 | SCREW | 10-82104540 | |
| 19 | SCREW, (M6 X 50) | 10-40057134 | |
| 20 | TUBING | 32-8M0108349 | 32-8M0047448, 32-830757130, 32-830757 80 |
| 21 | FUEL FILTER | 35-816296Q2 | |
| 22 | CABLE TIE, (8.00 Inch) | 54-816311T | 54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275 |
| 23 | FUEL CONNECTOR, Plastic | 22-816856Q3 | |
| 24 | GROMMET | 25-145091 | |
| 25 | SCREW, (M6 x 35) | 10-4010635 | |
| 26 | ENRICHNER VALVE | 89-819503A2 | |
| 27 | TUBING, (38.00 Inch) | 32-1430165 | |
| 28 | CLAMP | 54-18887 | |
| 29 | SCREW, (M8 x 35) | 10-82127335 | |
| 30 | FITTING Comment: (To Crankcase) | 22-64705 | |
| 31 | FUEL LINE, (57.00 Inches Bulk) | 32-8M0108355 | 32-8M0047428, 32-830756109, 32-99127109, 32-877821 |
| 32 | PLUG, Pipe (.0625-27), Non Oil Injection | 22-56800 | |
| 33 | FUEL LINE Comment: (To Carburetor) | 32-19017A1 | |
| 34 | CLAMP, (15.7), Old Design, New Design Use Reference Number 22 | 54-8M0214911 | |
| - | GASKET SET | 27-43004A99 | |
| - | FUEL PUMP DIAPHRAGM KIT | 42909A4 |
Fuel Pump(Use With Inline Check Valve)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Fuel Pump(Use With Inline Check Valve):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | FUEL PUMP ASSEMBLY | 14360A78 | |
| 2 | DIAPHRAGM KIT Comment: (See Note) | 21-857005A1 | |
| 3 | NOT SOLD SEPARATE, Check Valve | NSS | |
| 4 | NOT SOLD SEPARATE, Gasket | NSS | |
| 5 | NOT SOLD SEPARATE, Diaphragm | NSS | |
| 6 | NOT SOLD SEPARATE, Gasket | NSS | |
| 7 | NOT SOLD SEPARATE, Spring | NSS | |
| 8 | NOT SOLD SEPARATE, Cap | NSS | |
| 9 | NOT SOLD SEPARATE, Check Valve | NSS | |
| 10 | NOT SOLD SEPARATE, Retainer | NSS | |
| 11 | NOT SOLD SEPARATE, Spring | NSS | |
| 12 | NOT SOLD SEPARATE, Cap | NSS | |
| 13 | GASKET | 27-8M0204705 | |
| 14 | BASE | 144303 | |
| 15 | PLATE | 987752 | |
| 16 | ELBOW | 22-996642 | |
| 17 | SCREW, Fuel Pump | 10-82104540 | |
| 18 | SCREW, Pump To Block | 10-81754150 | |
| 19 | CABLE TIE, (8.00 Inch) | 54-816311T | 54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275 |
| 20 | TUBING | 32-8M0108349 | 32-8M0047448, 32-830757130, 32-830757 80 |
| 21 | CONNECTOR Comment: (To Crankcase) | 22-291112 | |
| 22 | TUBING Comment: (To Carburetor) | 32-8M0108349 | 32-8M0047448, 32-830757130, 32-830757 80 (To Carburetor) |
| 23 | FUEL FILTER, Design I | 35-816296Q2 | |
| 24 | FUEL LINE, Design I | 32-19017A1 | |
| 25 | TUBING, 6.50 Inch Commercial Engines | 32-8M0108349 | 32-8M0047448, 32-830757130, 32-830757 80 |
| 26 | MOLDED HOSE, Non Commercial Engines | 32-822554 | |
| 27 | PLUG, Non Commercial Engines | 19-822772 | |
| 28 | CHECK VALVE, Non Commercial Engines | 22-8189941 | |
| 29 | TUBING, (8.00 Inch), 5.50 Inch Non Commercial Engines Comment: (To Oil Pump) | 32-82381335 | |
| 30 | FUEL CONNECTOR, Plastic | 22-816856Q3 | |
| 31 | SCREW, (M6 x 35) | 10-4010635 | |
| 32 | GROMMET | 25-145091 | |
| 33 | ENRICHNER VALVE | 89-819503A2 | |
| 34 | TUBING, (38.00 Inch) | 32-1430165 | |
| 35 | CLAMP | 54-18887 | |
| 36 | SCREW, (M8 x 35) | 10-40011151 | |
| 37 | FUEL FILTER | 35-891642T03 | 35-87946T14, 35-87946T16 |
| 38 | BRACKET, Design II | 821698 | |
| 39 | SCREW, (M6 x 14), Design II | 10-4000327 | |
| 40 | WASHER, Design II | 12-4002315 | |
| 41 | NUT, (M6), Design II | 11-401386 | |
| 42 | TUBING, Design II | 32-8M0108349 | 32-8M0047448, 32-830757130, 32-830757 80 |
| - | GASKET SET | 27-43004A99 | |
| - | DIAPHRAGM KIT | 21-857005A1 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 | 13589T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 Commercial | 13600T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 90 | 15081T96 |
Gear Housing(Drive Shaft)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Gear Housing(Drive Shaft):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | GEAR HOUSING ASSEMBLY, Black | 1667-9011J16 | |
| - | GEAR HOUSING ASSEMBLY, Gray | 1667-9011J19 | |
| 1 | GEAR HOUSING ASSEMBLY, Black | 1667-9011T73 | |
| 1 | GEAR HOUSING ASSEMBLY, Gray | 1667-9011T74 | |
| 2 | PIN, Dowel (.375 x .625), Front | 17-8M0084244 | 17-43043 |
| 3 | OILER TUBE | 43046 | |
| 5 | SCREW, (.375-16 x .250) | 10-79953Q04 | |
| 6 | WASHER, Fiber | 12-191833 | |
| 7 | SCREW, Magnetic | 22-8M0058389 | 22-67892A06 |
| 8 | PIN, Dowel (.375 x .625), Rear | 17-43044 | |
| 9 | TRIM TAB | 97-31640Q4 | |
| 10 | SCREW, (.437-14 x 1.250) | 10-825427 | 10-15942 |
| 11 | WASHER, (.453 x .812 x .105) | 12-45176 | |
| 12 | CARRIER | 43040T1 | |
| 13 | PINION GEAR | 43-44484T | |
| 14 | NUT, (.625-18) | 11-35921 | |
| 15 | SHIFT CAM | 760394 | |
| 16 | TAPERED ROLLER BEARING ASSEMBLY | 31-42677A1 | |
| 17 | SHIM SET | 15-44492A1 | |
| 18 | DRIVE SHAFT ASSEMBLY | 45-43031A1 | |
| 19 | WEAR SLEEVE ASSEMBLY | 42461A1 | |
| 20 | GASKET | 27-8M0214931 | |
| 21 | GASKET | 27-430331 | |
| 22 | WATER PUMP BASE ASSEMBLY | 43055A4 | |
| 23 | OIL SEAL, Lower, Aluminum Cover | 26-43036 | |
| 24 | OIL SEAL, Upper, Aluminum Cover | 26-43035 | |
| 25 | GASKET ALUMINUM COVER Comment: (Use With Reference Number 30 And 31) (Aluminum Cover) | 27-430341 | |
| 25 | GASKET Comment: (Use Without Reference Number 30 And 31) (Aluminum Cover 6, 7) | 27-8172771 | |
| 22 | COVER ASSEMBLY, Plastic Cover | 43055A4 | |
| 22 | COVER ASSEMBLY, Aluminum Cover | 43055A4 | |
| 23 | OIL SEAL, Lower, Plastic Cover | 26-43036 | |
| 24 | OIL SEAL, Upper, Plastic Cover | 26-43035 | |
| 25 | GASKET ALUMINUM COVER, Plastic Cover | 27-430341 | |
| 26 | WATER PUMP ASSEMBLY Comment: (Use With Reference Number 30 And 31) | 817275A2 | |
| 27 | No Longer Available, Face Plate Comment: (Order 817275A2) (Use With Reference Number 30 And 31) | NLA | |
| 28 | SCREW, (M6 x 35), Use With Reference Number 30 And 31 | 10-4000332 | |
| 29 | SEAL, Use With Reference Number 30 And 31 | 8M0204658 | |
| 30 | WASHER, Use With Reference Number 30 And 31 | 12-4002315 | |
| 31 | INSULATOR, Use With Reference Number 30, 31, 6, And 7 | 23-8M0204659 | |
| 26 | WATER PUMP HOUSING, Upper, Use Without Reference Number 30, 31, And 7 | 817275A2 | |
| 27 | FACE PLATE, Use Without Reference Number 30, 31, And 7 | 8M0204709 | |
| 28 | SCREW, (M6 x 30), Use Without Reference Number 30 And 31 | 10-40011130 | |
| 29 | SEAL, Use Without Reference Number 30 And 31 | 8M0204658 | |
| 32 | KEY | 28-8M0204723 | |
| 33 | IMPELLER | 47-43026T2 | |
| 34 | SCREW, (M6 x 25) | 10-8M0204707 | |
| 35 | WASHER, (.281 x .500 x .060) | 12-8M0204649 | |
| 36 | SHIFT SHAFT ASSEMBLY | 43048A1 | |
| 37 | E RING | 53-29641 | |
| 38 | BUSHING ASSEMBLY | 23-43052A4 | |
| 39 | O-RING | 25-8M0204681 | |
| 40 | SEAL, Oil | 26-8M0204708 | |
| 41 | SCREW, (M6 x 20) | 10-8M0204741 | |
| - | GASKET SET | 27-43004A99 | |
| - | GEAR HOUSING SEAL KIT | 26-43035A4 | |
| - | WATER PUMP REPAIR KIT | 46-43024A7 |
Gear Housing(Propeller Shaft)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Gear Housing(Propeller Shaft):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | GEAR HOUSING ASSEMBLY, Black | 1667-9011J16 | |
| - | GEAR HOUSING ASSEMBLY, Gray | 1667-9011J19 | |
| 1 | GEAR HOUSING ASSEMBLY, Black | 1667-9011T73 | |
| 1 | GEAR HOUSING ASSEMBLY, Gray | 1667-9011T74 | |
| 42 | BEARING SET, Cup And Cone | 31-30894A1 | |
| 43 | FORWARD GEAR ASSEMBLY | 43-12634T02 | |
| 44 | ROLLER BEARING | 31-30895T | |
| 45 | CAM FOLLOWER ASSEMBLY | 850315A1 | |
| 45A | BALL | 30-44530 | |
| 46 | SPRING | 24-30622 | |
| 47 | CLUTCH | 52-822539T | 52-822539, 52-814756, 52-12777 |
| 48 | PIN, Cross | 17-8M0100263 | 17-8M0084681, 17-8M0020941, 17-30632 |
| 49 | SPRING | 24-30893 | |
| 50 | PROPELLER SHAFT | 44-12238T | |
| 51 | REVERSE GEAR | 43-12635T | |
| 52 | BEARING CARRIER ASSEMBLY | 8M0168901 | |
| 53 | O-RING | 25-8M0214974 | |
| 54 | ROLLER BEARING | 31-30956T | |
| 55 | SEAL, Inner | 26-8M0204670 | |
| 56 | OIL SEAL, Outer | 26-8M0205729 | |
| 57 | ROLLER BEARING | 31-12578T | |
| 58 | THRUST WASHER | 12-12577 | |
| 59 | THRUST BEARING | 31-12576 | |
| 60 | SCREW, (M8 x 30) | 10-4000354 | |
| 61 | WASHER | 12-4002317 | |
| 62 | SHIM SET | 15-44491A1 | |
| 63 | THRUST HUB AND WASHER ASSEMBLY | 13191Q01 | |
| 64 | TAB WASHER | 14-816629Q | 14-816629, 14-31210, 14-816629B |
| 65 | NUT, Propeller | 11-52707Q1 | |
| - | GEAR HOUSING SEAL KIT | 26-43035A4 | |
| - | GASKET SET | 27-43004A99 |
Induction Manifold And Reed Block
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Induction Manifold And Reed Block:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | GASKET | 27-43004009 | |
| 2 | BAFFLE PLATE | 428791 | |
| 3 | COVER | 42878A2 | |
| 4 | SCREW, (M8 x 35) | 10-82127335 | |
| 5 | SHIFT RAIL | 42881A1 | |
| 6 | TAB WASHER | 14-42981 | |
| 7 | SCREW, (M8 x 25) | 10-40001134 | |
| 8 | SLIDE | 988851 | |
| 9 | BUSHING, Old Design | 23-42994 | |
| 10 | WASHER, Wave, Old Design | 13-29720 | |
| 11 | WASHER, (.2656 x .625 x .0625) , Old Design | 12-35462 | |
| 12 | NUT, (M6) | 11-401386 | |
| 13 | WASHER | 12-35459 | |
| 14 | NUT, (M6) | 11-401386 | |
| 15 | LOWER END CAP ASSEMBLY | 1169-858552T2 | |
| 16 | CHECK VALVE | 21-426585 | |
| 17 | SEAL | 26-41953 | |
| 18 | O-RING | 25-89224 | |
| 19 | SCREW, (M10 x 25) | 10-4010825 | |
| 20 | GASKET | 27-430075 | |
| 22 | INDUCTION MANIFOLD | 884296T | 42967 2 |
| 23 | BRACKET | 42923 | |
| 24 | SCREW, (M8 x 35) | 10-82127335 | |
| 25 | SCREW, (M8 x 40) | 10-81742740 | |
| 26 | STUD | 16-8M0045410 | 16-93419 |
| 27 | WASHER | 12-8M0204663 | |
| 28 | WASHER, (.203 x .500 x .032), Old Design | 12-8M0204666 | |
| 29 | WING NUT | 11-816874 | 11-73651, 11-816873, 11-90052 |
| 30 | STUD, (M8 x 1.25) | 16-824470 | 16-42985, 16-42985 1 |
| 31 | ELBOW | 22-996642 | |
| 32 | TUBING | 32-8M0108349 | 32-8M0047448, 32-830757130, 32-830757 80 |
| 33 | TEE | 22-432881 | |
| 34 | REED BLOCK ASSEMBLY | 8M0219198 | |
| 35 | GASKET | 27-139376 | |
| 36 | REED SET | 34-43018A1 | |
| 37 | TAB WASHER | 14-429821 | |
| 38 | RETAINER | 42924 | |
| 39 | SCREW, (M6 x 16) | 10-4000171 | |
| - | GASKET SET | 27-43004A99 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 | 13589T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 75 Commercial | 13600T93 | |
| - | POWERHEAD ASSEMBLY COMPLETE, 90 | 15081T96 |
Oil Injection Components
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Oil Injection Components:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | OIL TANK | 1255-8627A7 | |
| 2 | BOOT, Upper | 99160001 | |
| 3 | BOOT | 99161 | |
| 4 | BRACKET, Upper | 988952 | |
| 5 | SCREW, (M6 x 30) | 10-4010630 | |
| 6 | CAP ASSEMBLY | 36-42653A3 | |
| 7 | GASKET | 27-42999T | |
| 8 | SCREW, (8-18 x .31) | 10-12896 | |
| 9 | SWITCH ASSEMBLY | 87-12886A6 | |
| 10 | DRIVEN GEAR | 43-430204 | |
| 11 | O-RING | 25-8M0204667 | |
| 12 | TUBING, (8.00 Inch), To Fuel Pump | 32-82381335 | |
| 13 | OIL PUMP | 42959A2 | |
| 14 | ADAPTOR ASSEMBLY | 17335A3 | |
| 15 | BUSHING | 23-17597 | |
| 16 | JOURNAL BUSHING | 23-17596 | |
| 17 | SCREW, Oil Pump | 10-82104540 | |
| 18 | BASE | 42888 | |
| 19 | GROMMET | 25-56291 | |
| 20 | SCREW | 10-82155050 | |
| 21 | CABLE TIE, (8.00 Inch) Comment: (As Required) | 54-816311T | 54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275 (As Required) |
| 22 | TUBING | 32-82381455 | |
| 23 | FITTING | 22-44456 | |
| 24 | TUBING, (14.50 Inches Bulk), Cut to 10.00 Inch Length | 32-9004934 | |
| 25 | CLAMP | 54-814200 | |
| 26 | WASHER, (.203 x .500 x .032) | 12-8M0204666 | |
| - | GASKET SET | 27-43004A99 |
Power Trim Components, Single Ram (0D252460 and Below)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Power Trim Components, Single Ram (0D252460 and Below):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | POWER TRIM PUMP | 8M0171818 | |
| 1 | SHOCK ROD KIT | 811666 | |
| 2 | CYLINDER END CAP ASSEMBLY | 813428 | |
| 3 | SHOCK PISTON | 811667 | |
| 4 | CYLINDER REBUILD KIT | 811668A1 | |
| 5 | MEMORY PISTON KIT | 810776 | |
| 6 | CYLINDER KIT | 893916A01 | 811669A 1 |
| 7 | SCREW AND SEAL KIT | 811678A6 | |
| 8 | PUMP/MANIFOLD | 8116705 | |
| 8A | ROCKER ARM | 823180A1 | |
| 9 | SCREW KIT | 10-813436 | |
| 10 | DRIVE SHAFT | 811671 | |
| 11 | SEAL KIT | 25-811672A4 | |
| 12 | RESERVOIR | 811673 | |
| 13 | PLUG KIT | 22-8134351 | |
| 14 | RELIEF VALVE KIT | 893929A01 | 813442A 2 |
| 15 | RESERVOIR CAP KIT | 811677 | |
| 16 | SCREW | 10-813446 | |
| 17 | RESERVOIR/MOTOR | 811674 | |
| 18 | ARMATURE | 811675 | |
| 19 | THRUST WASHER KIT | 12-811676 | |
| 20 | PIN, Anchor | 17-818898 | |
| 21 | PIN, Trilobe | 17-821539 | 17-13794, 17-19603 |
| 22 | SHAFT | 99625002 | |
| 25 | ANODE ASSEMBLY | 97-818298Q1 | |
| 26 | SCREW, (M6 x 25) | 10-8M0204707 | |
| 27 | WASHER, (.281 x .500 x .060) | 12-8M0204649 | |
| 28 | HARNESS ASSEMBLY | 84-819514A3 | |
| 29 | DELAY RELAY | 821509T01 | 821509, 853292 |
| 30 | BRACKET | 821382 | |
| 31 | BUSHING | 23-8M0214955 | |
| 32 | GROMMET | 25-818967 | |
| 33 | SCREW, (M5 x 25) | 10-40011109 | |
| 34 | SCREW, (#10-16 x .440) | 10-69079 | |
| 35 | C WASHER | 8M0084613 | 69205 |
| 36 | CLIP | 54-22740 |
Power Trim Components, Single Ram (0D252461 and Up)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Power Trim Components, Single Ram (0D252461 and Up):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | POWER TRIM PUMP | 8M0171817 | |
| 1 | SHOCK ROD ASSEMBLY | 8M0171821 | |
| 2 | CYLINDER END CAP ASSEMBLY | 813428 | |
| 3 | CYLINDER REBUILD KIT | 813432A1 | |
| 4 | MEMORY PISTON KIT | 810776 | |
| 5 | CYLINDER | 893916A01 | 811669A 1 |
| 6 | SCREW AND SEAL KIT | 811678A6 | |
| 7 | PUMP/MANIFOLD | 8116707 | |
| 8 | ROCKER ARM | 823180A1 | |
| 9 | SCREW KIT | 10-813436 | |
| 10 | DRIVE SHAFT | 8116711 | |
| 11 | SEAL KIT, With Case Bolts | 811626A3 | |
| 12 | RESERVOIR | 8116731 | |
| 13 | PLUG KIT | 22-8134351 | |
| 14 | RELIEF VALVE KIT | 893929A01 | 813442A 2 |
| 15 | FRAME AND FIELD KIT | 8116241 | |
| 16 | ARMATURE KIT | 8116271 | |
| 17 | BRUSH SPRING KIT | 12665 | |
| 18 | BRUSH CARD KIT | 811625 | |
| 19 | PIN, Anchor | 17-818898 | |
| 20 | PIN, Trilobe | 17-821539 | 17-13794, 17-19603 |
| 21 | SHAFT | 99625002 | |
| 22 | ANODE ASSEMBLY | 97-818298Q1 | |
| 23 | SCREW, (M6 x 25) | 10-8M0204707 | |
| 24 | WASHER, (.281 x .500 x .060) | 12-8M0204649 | |
| 25 | CONTROL HARNESS, (17.00 Inches) | 84-17201A2 | |
| 26 | SCREW, (10-16 X .38) | 10-878607 | 10-817626 |
| 27 | C WASHER | 8M0084613 | 69205 |
| 28 | CLIP | 54-22875 | |
| 29 | SOLENOID | 89-8M0185145 | |
| 30 | BUSHING | 23-8M0214955 | |
| 31 | GROMMET | 25-818967 | |
| 32 | SCREW, (M5 x 25) | 10-40011109 | |
| 33 | WASHER | 12-4002314 |
Power Trim Components, Three Ram (Design I )
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Power Trim Components, Three Ram (Design I ):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | MANIFOLD ASSEMBLY, Black | 99659A21 | |
| 1 | MANIFOLD ASSEMBLY, Gray | 99659A22 | |
| 2 | PIPE PLUG | 22-56800 | |
| 3 | TRIM CYLINDER ASSEMBLY, Black | 41493A7 | |
| 3 | TRIM CYLINDER ASSEMBLY, Gray | 41493A7 | |
| 4 | GUIDE ASSEMBLY | 41492A1 | |
| 5 | REPAIR KIT | 25-41478A1 | |
| 6 | CHECK VALVE KIT | 41482A2 | |
| 7 | GUIDE ASSEMBLY | 1100-8M0021648 | 878243A 1 |
| 8 | PISTON AND ROD ASSEMBLY, Port | 878413A1 | |
| 9 | TRIM FILTER ASSEMBLY | 35-12184A1 | |
| 10 | PISTON AND ROD ASSEMBLY, Starboard | 878414T01 | 878414A 1 |
| 11 | PIN, Trilobe, Trim Cylinder, Upper | 17-821539 | 17-13794, 17-19603 |
| 12 | VALVE ASSEMBLY | 893929A01 | 813442A 2 |
| 12A | E-RING | 53-815949001 | 53-812844, 53-835104 |
| 13 | SCREW, (M6 x 14) | 10-4000327 | |
| 14 | WASHER | 12-4002315 | |
| 15 | COVER | 99642 | |
| 16 | O-RING KIT | 25-48462A4 | |
| 17 | PLUG ASSEMBLY | 19-99609A1 | |
| 18 | SHAFT ASSEMBLY | 99641A1 | |
| 19 | PIPE PLUG, Shaft | 22-56800 | |
| 20 | SCREW, (M6 x 20) | 10-4008820 | |
| 21 | LOCKWASHER, (M6) | 13-400256 | |
| 22 | POWER TRIM PUMP Comment: (Refer To Power Trim Pump For Breakdown) | 826729A10 | 826729A09, 826729A08, 826729A07, 826729A 4 (Refer To Power Trim Pump For Breakdown) |
| 23 | SHAFT | 99625002 | |
| 24 | ANODE ASSEMBLY | 97-818298Q1 | |
| 25 | SCREW, (M6 x 25) | 10-8M0204707 | |
| 26 | WASHER, (.281 x .500 x .060) | 12-8M0204649 | |
| 27 | STRIKER PLATE | 8M0045383 | 99630 1 |
| 28 | LOCKWASHER, (.375) | 13-58643 | |
| 29 | NUT, (.375-24) | 11-46335 | |
| 30 | CONTROL HARNESS, (17.00 Inches) | 84-17201A2 | |
| 31 | WIRE ASSEMBLY, (2.750 Inches), Red | 84-87379A14 | |
| 31 | CABLE ASSEMBLY (3.50 Inch) Black | 84-88807A13 | |
| 32 | STARTER SOLENOID, ( 8-32 .250-20 Terminals) | 89-8M0185146 | |
| 33 | SCREW, (M5 X 13) | 10-40007106 | |
| 34 | NUT, | 8-32,11-26419 | |
| 35 | LOCKWASHER, (.250) | 13-26992 | |
| 36 | NUT, ( #8-32) | 11-64015 | |
| 37 | WASHER | 12-4002314 | |
| 38 | CLIP | 54-22875 | |
| 39 | C WASHER | 8M0084613 | 69205 |
| 40 | SCREW, (#10-16 x .440) | 10-69079 | |
| 41 | GROOVE PIN, Lower | 17-878267 | 17-44431 |
| 42 | SCREW, (M10 x 30) | 10-4000377 | |
| 43 | LOCKWASHER | 13-400258 | |
| 44 | J CLIP, Old Design | 54-47483 |
Power Trim Components, Three Ram (Design II )
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Power Trim Components, Three Ram (Design II ):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | POWER TRIM ASSEMBLY, Complete | 826729A10 | 826729A09, 826729A08, 826729A07, 826729A 4 |
| 1 | MANIFOLD ASSEMBLY | 811604F | 811604T |
| 2 | PIPE PLUG | 22-56800 | |
| 3 | TILT CYLINDER ASSEMBLY | 880952A03 | 880952A02, 880952A 1 |
| 4 | PISTON ROD, Bolt Type | 811608 | |
| 5 | PISTON ROD, Nut Type | 823553T | 823553, 811609 |
| 6 | GUIDE KIT | 878239A02 | 878239A 1 |
| 7 | REPAIR KIT | 811607A1 | |
| 8 | CHECK VALVE KIT | 811610A1 | |
| 9 | GUIDE ASSEMBLY | 1100-8M0021648 | 878243A 1 |
| 10 | PISTON AND ROD ASSEMBLY, Port | 878413A1 | |
| 10 | PISTON AND ROD ASSEMBLY, Starboard | 878414T01 | 878414A 1 |
| 11 | TRIM FILTER ASSEMBLY | 35-12184A1 | |
| 12 | PIN, Trilobe | 17-821539 | 17-13794, 17-19603 |
| 13 | VALVE ASSEMBY | 893929A01 | 813442A 2 |
| 14 | E-RING | 53-815949001 | 53-812844, 53-835104 |
| 15 | SCREW, (M6 x 14) | 10-4000327 | |
| 16 | WASHER | 12-4002315 | |
| 17 | COVER | 811611 | |
| 18 | O-RING KIT | 811612A3 | |
| 19 | PLUG ASSEMBLY | 19-811613 | |
| 20 | SHAFT ASSEMBLY | 8M0142997 | |
| 21 | PIPE PLUG | 22-56800 | |
| 22 | TRIM MOTOR Comment: (Refer To Co-Pilot Or Tachometer Section For Breakdown) | 878265A6 | |
| 23 | SCREW, Long | 10-811615 | |
| 23 | SCREW, Short | 10-811616 | |
| 24 | PUMP | 811617T1 | |
| 25 | DRIVE SHAFT | 811619 | |
| 26 | SHAFT | 99625002 | |
| 27 | ANODE ASSEMBLY | 97-818298Q1 | |
| 28 | SCREW, (M6 x 25) | 10-8M0204707 | |
| 29 | WASHER, (.281 x .500 x .060) | 12-8M0204649 | |
| 30 | STRIKER PLATE | 8M0045383 | 99630 1 |
| 31 | LOCKWASHER, (.375) | 13-58643 | |
| 32 | NUT, (.375-24) | 11-46335 | |
| 33 | GROOVE PIN | 17-878267 | 17-44431 |
| 34 | SCREW, (M10 x 30), Manifold | 10-4000377 | |
| 35 | LOCKWASHER, Manifold Screw | 13-400258 | |
| 36 | CLIP, Pump Wire | 54-22875 | |
| 37 | C WASHER | 8M0084613 | 69205 |
| 38 | SCREW, (#10-16 x .440) | 10-69079 |
Power Trim Motor
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Power Trim Motor:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | TRIM MOTOR | 878265A6 | |
| 1 | FRAME AND FIELD KIT | 811624 | |
| 2 | BRUSH CARD KIT | 811625 | |
| 3 | END FRAME KIT | 811623 | |
| 4 | SEAL KIT | 811626 | |
| 5 | ARMATURE KIT | 811627 |
Power Trim Pump
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Power Trim Pump:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | POWER TRIM PUMP | 826729A10 | 826729A09, 826729A08, 826729A07, 826729A 4 |
| 1 | FRAME AND FIELD KIT | 12659 | |
| 2 | BRUSH SPRING KIT | 12665 | |
| 3 | BRUSH CARD KIT | 13506 | |
| 4 | PUMP AND END FRAME KIT | 12662 | |
| 5 | PUMP SEAL KIT | 126631 | |
| 6 | END FRAME KIT | 12660 | |
| 7 | ARMATURE KIT | 12661 | |
| 8 | THRU BOLT KIT | 12664 |
Service/Support Material
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Service/Support Material:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | 75/90 HP (3 CYLINDER) | 90-81589890 | |
| - | SERVICE MANUAL | 90-136452 | |
| - | GASKET SET | 27-43004A99 | |
| - | DECAL SET, Black 75 | 37-810457A90 | 37-13488A90 |
| - | DECAL SET, Black 90 | 37-12565A89 | |
| - | DECAL SET, Commercial, Gray 75 | 37-43601A87 | |
| - | DECAL SET, Gray 75/90 | 37-815628A92 | 37-810465A90, 37-43575A87, 37-810466A90, 37-11623A87, 37-816119A90 |
| - | OWNER'S GUIDE, Black | 90-12428920 | |
| - | OWNER'S GUIDE, Gray | 90-14699920 |
Starter Motor(Bosch)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Starter Motor(Bosch):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| - | STARTER MOTOR | 50-893891T | 50-66015T 1 |
| 1 | DRIVE KIT | 90643 | |
| 2 | DRIVE ASSEMBLY | 685753 | |
| 3 | PLATE | 75660 | |
| 4 | BOLT | 10-75385 | |
| 6 | ARMATURE | 75386 | |
| 7 | BRUSH/SPRING KIT | 898265016 | 75384, 75384 1 |
| 8 | BUSHING | 23-57387 | |
| 9 | NOT SOLD SEPARATE, Washer, American Bosch Number WA-1728 | NSS | |
| 10 | LOCKWASHER, (.250) | 13-26992 | |
| 11 | NUT, (.250-20) | 11-20890 | |
| 12 | HOLDER | 898265014 | 61787 |
| 13 | Not Sold Seperate, (.250 Diameter), Screw, American Bosch Number 02441-22-SC-30SM (#N.S.S.) | ||
| 14 | END CAP | 15386001 |
Steering Handle Components
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Steering Handle Components:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | BRACKET ASSEMBLY, Black | 12022A13 | |
| 1 | BRACKET ASSEMBLY, Gray | 12022A14 | |
| 2 | TACHOMETER ASSEMBLY | 79-12012A1 | |
| 3 | NUT | 11-65110 | |
| 4 | STUD | 16-12782 | |
| 5 | SPACER | 15126 | |
| 6 | TAB WASHER | 14-12080 | |
| 7 | NUT | 11-4002016 | |
| 8 | GROMMET | 121051 | |
| 9 | HARNESS ASSEMBLY | 84-12649A2 | |
| 10 | KEY SWITCH, See Chart For Key | 87-88107A5 | |
| 11 | NUT, Special | 11-879755 | 11-93543 |
| 12 | COVER | 12015A1 | |
| 13 | SCREW, (#10-16 x .500) | 10-878608 | 10-812832 |
| 14 | PLUG | 19-889730 | 19-12014 |
| 15 | SWITCH ASSEMBLY, Stop | 87-11083A4 | |
| 16 | LANYARD ASSEMBLY | 15920Q54 | |
| 17 | RETAINER | 8M0032846 | 12044 1 |
| 18 | SCREW, (M8 x 50) | 10-4000358 | |
| 19 | TAB WASHER | 14-42981 | |
| 20 | BUSHING | 23-889732 | 23-42992 1 |
| 21 | SHIFT LEVER, Black | 12021A1 | |
| 21 | SHIFT LEVER, Gray | 12021A2 | |
| 22 | WASHER | 12-815351 | |
| 23 | STUD, (.375-24 x 1.125) | 16-8M0034452 | 16-58152 |
| 24 | KNOB | 98530 | |
| 25 | SHIFT ROD | 495636 | |
| 26 | ROD END | 48419T | |
| 27 | BUSHING | 23-26856 | |
| 28 | WASHER, (.281 x .500 x .060) | 12-8M0204649 | |
| 29 | COTTER PIN | 18-25191 | |
| 30 | NEUTRAL START SWITCH | 87-93479A7 | |
| 31 | BRACKET | 12609 | |
| 32 | BRACKET | 126101 | |
| 33 | SCREW, (#4-40 x .630) | 10-90342 | |
| 34 | NUT, | 4-40,11-24832 | |
| 35 | SCREW, (#8-32 x .375) | 10-57583T | |
| 36 | WASHER | 12-20878 | |
| 37 | NUT, | 8-32,11-26419 | |
| 38 | SCREW, (M8 x 25) | 10-40001134 | |
| 39 | DETENT/SPRING KIT | 12016A2 | |
| 40 | TRIM SWITCH (36.00 Inch) Two Ring Terminal | 87-14645A2 | |
| 40 | TRIM SWITCH (23.00 Inch) Two Male Terminals | 87-14645A4 | |
| 41 | NUT, (.468-32) | 49440 | |
| - | KEY | 894911 | |
| - | KEY, Ignition | 894912 | |
| - | KEY 1C | 894913 | |
| - | KEY 1D | 894914 | |
| - | KEY 1E | 894915 | |
| - | KEY 1F | 894916 | |
| - | KEY 2A | 894917 | |
| - | KEY 2B | 894918 | |
| - | KEY 2C | 894919 | |
| - | KEY, Ignition (2D) | 8949110 | |
| - | KEY, Ignition (2E) | 8949111 | |
| - | KEY, Ignition (2F) | 8949112 |
Steering Handle Components(With Steering Arm)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Steering Handle Components(With Steering Arm):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | HANDLE ASSEMBLY, Steering Arm, Black | 12020A3 | |
| 1 | STEERING ARM, Gray | 12020A4 | |
| - | FITTING, Grease | 22-8M0169589 | |
| 2 | TUBE ASSEMBLY | 12018A4 | |
| 3 | HOUSING | 48414 | |
| 4 | PLATE | 48519 | |
| 5 | GASKET | 27-48518 | |
| 6 | SCREW, (10-24 X .50) | 10-72169 | |
| 6 | SCREW, (#10-16 x .500) | 10-878608 | 10-812832 |
| 7 | CLAMP | 54-889729 | 54-12013 |
| 8 | NUT, (M5 x 40) | 10-40007112 | |
| 9 | WING NUT | 11-816874 | 11-73651, 11-816873, 11-90052 |
| 10 | STOP SWITCH KIT, Throttle Handle | 87-823609A15 | 87-15823A 6, 96495A 3, 87-15823A 5 |
| 11 | STOP SWITCH, Design II, With Metal Lock Ting | 87-8M0104612 | 87-823609A 5 |
| 12 | No Longer Available, Stop Switch, Design I, Odres Kit 87-823609A15 | NLA | |
| 13 | SCREW, (#10-16 x .375) | 10-62568 | |
| 14 | GRIP | 8M0221732 | |
| 15 | CLAMP | 54-648552 | |
| 16 | SCREW, (#10-16 x .600) | 10-878609 | 10-812832 1 |
| 17 | CONDUIT | 8885242 | |
| 18 | GUIDE TUBE | 8M0026078 | 89566 1 |
| 19 | BARREL | 89578 | |
| 20 | SET SCREW, | 10-32,10-824081 | 10-89601 |
| 21 | CABLE | 12019 | |
| 22 | GUIDE | 8M0204660 | |
| 23 | ANCHOR | 20007 | |
| 24 | SET SCREW, | 8-32,10-8M0204644 | |
| 25 | SCREW, (M10 x 105) | 10-823567105 | 10-817430105 |
| 26 | CAP | 48416 | |
| 27 | WASHER | 12-4002319 | |
| 28 | WASHER | 12-12024 | |
| 29 | SPACER | 23-146011 | |
| 30 | BUSHING | 23-812930A1 | |
| 31 | NUT, (M10) | 11-40140 | |
| 38 | ALARM HORN AND WIRE ASSEMBLY | 68878A6 | |
| 39 | COVER | 68879 | |
| 40 | SCREW, (M5 x 16) | 10-40056107 |
Swivel Bracket And Steering Arm(Casting Number 1499-8709C5)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Swivel Bracket And Steering Arm(Casting Number 1499-8709C5):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | SWIVEL BERACKET ASSEMBLY, Black | 1499-8M0102865 | 1499-8710T20 |
| 1 | SWIVEL BRACKET ASSEMBLY, Gray | 1499-8710T21 | |
| 2 | SEAL, Oil, Lower | 26-87735 | |
| 3 | BUSHING | 23-818764 | 23-67669 |
| 4 | O-RING | 25-33466 | |
| 5 | SPACER | 23-67668 | |
| 6 | FITTING, Grease | 22-8M0169589 | |
| 7 | BUSHING | 23-821207 | 23-99608 |
| 8 | SCREW, (.250-28 x .500) | 10-64014 | |
| 9 | STEERING LINK ASSEMBLY | 92876A12 | |
| 10 | SCREW, (.375-24 x 1.25), Non Handle | 10-849838 | 10-14000 |
| 11 | NUT, (.375-24) | 11-8M0204726 | |
| 12 | WASHER, (.406 x .734 x .063) | 12-34931 | |
| 13 | WAVE WASHER | 13-78854 | |
| 14 | BOTTOM YOKE, Black | 42961A06 | |
| 14 | BOTTOM YOKE MARINER, Gray | 42961T2 | |
| 15 | RETAINING RING | 53-67684 | |
| 16 | WASHER | 12-67670 | |
| 17 | BRACKET, Not Used With Power Trim | 99653 | |
| 18 | SHAFT, Lower, Not Used With Power Trim | 99619 | |
| 19 | PIN, Trilobe, Not Used With Power Trim | 17-821539 | 17-13794, 17-19603 |
| 20 | SCREW, (M10 x 30), Not Used With Power Trim | 10-4000377 | |
| 21 | LOCKWASHER, Not Used With Power Trim | 13-400258 | |
| 22 | ANODE ASSEMBLY, Not Used With Power Trim | 97-818298Q1 | |
| 23 | SCREW, (M6 x 35), Not Used With Power Trim | 10-4000332 | |
| 24 | WASHER, (.281 x .500 x .060), Not Used With Power Trim | 12-8M0204649 | |
| 25 | SHOCK ABSORBER, Not Used With Power Trim Comment: (Black) | 55-99724T15 | |
| 25 | SHOCK ABSORBER, Not Used With Power Trim Comment: (Gray) | 55-99724T15 | |
| 26 | BUSHING, Not Used With Power Trim | 23-821207 | 23-99608 |
| 27 | SHAFT, Upper | 99625002 | |
| 28 | SWIVEL PIN/STEERING ARM, Black | 99661A35 | |
| 28 | SWIVEL PIN/STEERING ARM, Gray | 99661A36 | |
| 29 | SWIVEL PIN/STEERING ARM Comment: (Handle Models, Black) | 12079A8 | |
| 29 | SWIVEL PIN/STEERING ARM Comment: (Handle Models, Gray) | 12079A9 |
Swivel Bracket And Steering Arm(Casting Number 1499-8709C6)
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Swivel Bracket And Steering Arm(Casting Number 1499-8709C6):
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | SWIVEL BERACKET ASSEMBLY, Black Comment: (Use With Non Power Trim And Three Ram Power Trim) | 1499-8M0102865 | 1499-8710T20 (Use With Non Power Trim And Three Ram Power Trim) |
| 1 | SWIVEL BRACKET ASSEMBLY, Gray Comment: (Use With Non Power Trim And Three Ram Power Trim) | 1499-8710T21 | |
| 1 | SWIVEL BRACKET, Black Comment: (Use With Single Ram Power Trim) | 1400-8M0220957 | |
| 1 | SWIVEL BRACKET, Gray Comment: (Use With Single Ram Power Trim) | 3408-818904T2 | |
| 2 | SEAL, Oil, Lower | 26-87735 | |
| 3 | BUSHING | 23-818764 | 23-67669 |
| 4 | O-RING | 25-8M0214926 | |
| 5 | SPACER | 23-816039 | |
| 6 | FITTING, Grease | 22-8M0169589 | |
| 7 | BUSHING | 23-821207 | 23-99608 |
| 8 | SCREW, (.250-28 x .500) | 10-64014 | |
| 9 | STEERING LINK ASSEMBLY | 92876A12 | |
| 10 | SCREW, (.375-24 x 1.25), Non Handle | 10-849838 | 10-14000 |
| 11 | NUT, (.375-24) | 11-8M0204726 | |
| 12 | WASHER, (.406 x .734 x .063) | 12-34931 | |
| 13 | PIN, Trilobe | 17-821539 | 17-13794, 17-19603 |
| 14 | BOTTOM YOKE, Black | 42961A06 | |
| 14 | BOTTOM YOKE MARINER, Gray | 42961T2 | |
| 15 | RETAINING RING | 53-67684 | |
| 16 | WASHER, Thrust | 12-816432 | |
| 17 | BRACKET | 99653 | |
| 18 | SHAFT, Lower, Not Used With Power Trim | 99619 | |
| 19 | PIN, Trilobe | 17-821539 | 17-13794, 17-19603 |
| 20 | SCREW, (M10 x 30) | 10-4000377 | |
| 21 | LOCKWASHER | 13-400258 | |
| 22 | ANODE ASSEMBLY | 97-818298Q1 | |
| 23 | SCREW, (M6 x 25) | 10-8M0204707 | |
| 24 | WASHER, (.281 x .500 x .060) | 12-8M0204649 | |
| 25 | SHOCK ABSORBER, Black Comment: (No Stamping, Not Used With Power Trim) | 55-99724T15 | |
| 25 | SHOCK ABSORBER, Gray Comment: (No Stamping, Not Used With Power Trim) | 55-99724T15 | |
| 25 | SHOCK STAMPED A12, Black Comment: (Not Used With Power Trim) | 55-99724T15 | |
| 25 | SHOCK STAMPED A12, Gray Comment: (Not Used With Power Trim) | 55-99724T15 | |
| 26 | BUSHING | 23-821207 | 23-99608 |
| 27 | SHAFT, Upper | 99625002 | |
| 28 | SWIVEL PIN/STEERING ARM, Black | 99661A35 | |
| 28 | SWIVEL PIN/STEERING ARM, Gray | 99661A36 | |
| 29 | SWIVEL PIN/STEERING ARM, Black Comment: (Handle Models) | 12079A8 | |
| 29 | SWIVEL PIN/STEERING ARM, Gray Comment: (Handle Models) | 12079A9 |
Tachometer
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Tachometer:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | TACHOMETER, 6K | 79-895283Q43 | 79-825348A 1 |
| 2 | BRACKET, Mounting | 79101T | |
| 3 | LIGHT BULB | 88-72729 | |
| 4 | SOCKET, Light Bulb | 88-79888 | |
| 5 | NUT, | 8-32,11-26419 | |
| 6 | HARNESS ASSEMBLY, Tachometer (5.00 Feet) | 84-86396A8 |
Throttle Lever And Linkage
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Throttle Lever And Linkage:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | LEVER | 42946T1 | |
| 2 | ADJUSTING SCREW, (5 MM) | 10-817582 | 10-814775, 10-42977 |
| 3 | NUT, (M5) | 11-400211 | |
| 4 | LEVER | 429471 | |
| 5 | ADJUSTING SCREW, (M6 x 55) | 10-814776 | 10-42978 |
| 6 | NUT, (M6) | 11-400212 | |
| 7 | CAP | 42942 | |
| 8 | STUD, Design I | 16-42986 | |
| 9 | NUT, (M10), Design I | 11-90517 | |
| 10 | SCREW, (M10 x 45), Design II | 10-4007180 | |
| 11 | WASHER, Design II | 12-42980 | |
| 12 | SPRING | 24-55162 | |
| 13 | INSERT | 42927 | |
| 14 | WASHER | 12-35459 | |
| 15 | NUT, (M6) | 11-401386 | |
| 16 | ROD | 878172 | 42918 |
| 17 | SWIVEL BASE | 93254 | |
| 18 | SWIVEL BALL | 93421 | |
| 19 | ROD | 878420T | 878420, 42919 |
| 20 | SPRING | 24-14159 | |
| 21 | BUSHING | 23-8M0215006 | |
| 22 | CAM | 42948A7 | |
| 23 | STUD | 16-8161949 | |
| 24 | WASHER, (.255 x .620 x .03) | 12-69056 | |
| 25 | NUT, (M6) | 11-401386 | |
| 26 | BUSHING | 23-812930A1 |
Transom Bracket
Back to TopBelow is the parts list for Mercury 75 (3 CYL.) Transom Bracket:
| Position No. | Part Name | OEM Number | Supersedes |
|---|---|---|---|
| 1 | TRANSOM BRACKET, Starboard, Black | 3401-8718F7 | |
| 2 | TRANSOM BRACKET, Port, Black | 3400-8716A8 | |
| 1 | TRANSOM BRACKET, Starboard, Gray | 3401-8718F8 | |
| 2 | TRANSOM BRACKET, Port, Gray | 3400-8716A9 | |
| 3 | FITTING, Grease, Port | 22-8M0169588 | |
| 4 | TILT LOCK PIN ASSEMBLY, Non Power Trim | 17-8M0026068 | 17-49930A 1 |
| 5 | TILT TUBE, Power Trim | 99170A2 | |
| 6 | NUT, Black | 11-859133 | 11-34862, 11-90068F 3, 11-90068F 4 |
| 6 | NUT, (1.00-14), Gray | 11-859133 | 11-34862, 11-90068F 3, 11-90068F 4 |
| 7 | O-RING | 25-45711 | |
| 8 | WAVE WASHER | 13-88750 | |
| 9 | NUT, (.875-14) | 11-858869 | 11-30499 |
| 10 | SCREW, (.500-20 x 4.00) | 10-814259 | |
| 11 | WASHER | 12-8M0204648 | |
| 12 | NUT | 11-91962 | |
| 13 | LEVER ASSEMBLY, Non Power Trim And Three Ram Power Trim | 8M0115104 | 8M0115103, 99629T 2 |
| 14 | TILT LOCK LEVER, Single Ram Power Trim | 8M0109798 | 821176T02, 821176T 1 |
| 15 | WAVE WASHER | 13-99611 | |
| 16 | NYLINER | 23-65830 | |
| 17 | KNOB | 99633 | |
| 18 | PIN | 17-99615 | |
| 19 | SPRING | 24-99622 | |
| 20 | GROOVE PIN | 17-99604 | |
| 21 | BOLT ASSEMBLY, Power Trim | 10-96930A1 | |
| 22 | NUT, (.375-24), Power Trim | 11-23161 | |
| 23 | NUT, (.875-14), Power Trim | 11-8M0041651 | 11-37984 |
| 24 | ANCHOR BRACKET, Black Comment: (Single Ram Power Trim) | 8M0086406 | 818771T 1 (Single Ram Power Trim) |
| 24 | ANCHOR BRACKET, Gray Comment: (Single Ram Power Trim) | 818771T8 | |
| 25 | SCREW, (M10 x 30), Single Ram Power Trim | 10-4000377 | |
| 26 | LOCKWASHER, Single Ram Power Trim | 13-400258 | |
| 27 | NUT, (M10), Single Ram Power Trim | 11-40114 | |
| 28 | STOP | 814207 |
Download this page as PDF: Click here
For Mercury Owners:
To assist you in maintaining and repairing your marine engines, we hope the following resources may be of use:
-
Mercury / Mercruiser / Mariner Parts from JLM Marine
- Mercury Thermostat
- Mercury Water Pump
- Mercury Water Pump Impeller
- Mercury Water Pump Impeller Kit
- Mercury Carburetor
- Mercury Carburetor Repair Kit
- Mercury Fuel Pump
- Mercury Fuel Pump Kit
- Mercury Air Filter
- Mercury Oil Filter
- Mercury Oil Seal
- Mercury Fuel Filter
- Mercury Gasket
- Mercury Relay
- Mercury Ignition Switch
- Mercury Trim Tilt Switch
- Mercury Ignition Sensor
- Mercury Spark Plug Wire
- Mercury Water Distribution Housing
- Mercury Bellow
- Mercury Bellows Kit
- Mercury Serpentine Pulley
- Mercury Accessories
- Mercury Belt
- Mercury Oil Plug
- Mercury Drain Plug
- Mercury Bellows Replacement Tool
About JLM Marine
Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.
As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.
We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.
Mercury Parts on Sale
Carburetor for Mercury 8HP 9.9HP 8M0176126
Product Details: Part Numbers: OEM: Mercury Mariner 3303-895110T11, 3303-8M0104462, 1300-8M0167272, 3303-895110T01, 8M0173875, 8M0176126 Aftermarket: AM8M0176126 Equivalent Part Numbers: 8M0167272, 8M0173875, 895110A03, 895110T15, 8M0104462, 895110A13, 895110T01, 895110T11, 8M0104464, 895110A18, 3303-895110T01, 3303-895110T11 Compatible Models: Mercury Mariner: Four-Stroke Engines: 8HP 9.9HP Product Features High Quality: Manufactured to...
- $58.60
$70.00- $58.60
- Unit price
- per
Water Drain Distribution Housing Assembly for Mercury MerCruiser 4.3 5.0 5.7 6.2L and 350 377 383 MPI
Product Details: Fits: Mercury MerCruiser 4.3 5.0 5.7 6.2L and 350 377 383 MPI Replaces OEM: Mercury MerCruiser 863444T1, 863444A1, 863802T2 and 863444T2 Compatible Models: Mercury MerCruiser: Specific Models: 4.3 5.0 5.7 6.2L, 350 377 383 MPI Product Features High Quality: Manufactured to OEM...
- $87.90
$119.00- $87.90
- Unit price
- per
Fuel Pump Assembly for Mercury Mariner 15-55HP 2-Stroke Models (43113T)
OEM Part Numbers 43113T, 43113M, 93045M, 94799M, 84651M, 81328M, 84139M, 853729A1 Compatible Models Mercury Two-Stroke Engines: 9.5A, 12A, 15A, 15, 20C / 25C (Thru prop. exhaust) 30A, 40 (Twin Carb) (W/oil injection) (w/auto-blend) 55, W-55, 70 Mariner Two-Stroke Engines: 9.5A, 12A, 15A, 15, 20C...
- $28.90
- $28.90
- Unit price
- per
Mercury MerCruiser Stern Drive Engine Decals Sticker Kit Set 37-15167A90 Fit Bravo One - JLM Marine
- Red
Reference Code JLM Marine 23DC024B, Mercury MerCruiser Marine 37-15167A90, Mercury MerCruiser Marine 15167A90 This marine engine sticker replaces faded or missing OEM decals on SternDrive, inboard engines, or shaft drives. Compatibility MerCruiser BRAVO ONE Product Use Meets regulations and emission-label compliance requirements Replaces faded...
- $22.80
- $22.80
- Unit price
- per
-
Red
-
Blue
Fuel Pump Assembly for Mercury/Mariner 35HP-300HP 2-Stroke Models (14360A16, 14360A41, 14360A43)
OEM Part Numbers 14360A16, 14360A41, 14360A43, 14360A50, 14360A71, 14360A73, 14360T74, 14360A78, 8M0036779, 98766, 14430-C1, 14360T77 Compatible Models Mercury Two-Stroke Engines: 35HP, 50HP, 60HP, 115HP 75/90/115 HP DFI (1.5L) 200/225/250/300 HP DTS/DFI Mariner Two-Stroke Engines: 30-250HP Outboard Explosion Diagram Technical Specifications Weight: 228g Package Dimensions:...
- $52.90
$60.00- $52.90
- Unit price
- per
Carburetor Rebuild Kit for Mercury Mariner Nissan 2.5HP, 3.5HP; Tohatsu 2.5HP, 3.5HP 2-Stroke Models (3F0-87122-1)
OEM Part Numbers Yamaha: 6G1-W0093-00, 6G1-W0093-00-00, 6G1-W0093-00-XX, 6G1W009300, 6G1W00930000, 6G1W009300XX, 6L5-W0093-00-00, 6L5W00930000, 6N0-W0093-00-00, 6N0W00930000, 6G1-W0093-01-00, 6G1W00930100 Mercury/Mariner: 11502M Sierra: 18-7765 Tohatsu: 369-87122-1, 369871220, 369871220M, 369871221, 369871221M, 3B2871220, 3B2871220M, 3K9871220, 3K9871220M Aftermarket: AM6G1-W0093-00 Compatible Models Nissan Two-Stroke Engines: NS 2.5A2, NS 3.5A2, NS 3.5B, NS...
- $22.50
$13.00- $22.50
- Unit price
- per
Fuel Pump Assembly for Mercury/Mariner 9.9-30HP 4-Stroke Models (803529T04)
OEM Part Numbers 803529T04 Compatible Models Mercury/Mariner Four-Stroke Engines: 10 HP Carbureted 2-Cylinder 15 HP Carbureted 2-Cylinder (includes Seapro) 20 HP Carbureted 2-Cylinder 25 HP EFI 3-Cylinder (includes 25 JET EFI & SEAPRO) 30 HP EFI 3-Cylinder Explosion Diagram Technical Specifications Weight: 251g Package...
- $57.90
$72.00- $57.90
- Unit price
- per
Water Pump Impeller Kit for Mercury 2 Str 15-25 HP 4 Str 9.9-15 HP 99157T2
Product Details: Part Numbers: Mercury Mariner 99157T2, 85098A2, 99157A2 Equivalent Part Numbers: 46-99157A02, 46-99157T2, 85098A2, 99157A02, 99157A2, 99157T2. HJ MHJB-99157, AM46-99157T2, GLM12014 Included in Repair Kits: Yes Compatible Models: Mercury: Two-Stroke Engines: 15 hp, 18 hp, 20 hp, 25 hp Four-Stroke Engines: 9.9 hp,...
- $57.50
$63.00- $57.50
- Unit price
- per
Carburetor for Mercury 8 9.9 13 15 HP 3323-835382T04
OEM Part Numbers Replaced: 3323-835382A1, 3323-835382T1, 3323-835382T3, 3323-835382T04 Compatibility: Engine Models: Mercury/Mariner 4-Stroke Outboards: 9.9HP (323 cc) 13.5HP (International models) 15HP (323 cc) Specific Applications: Mercury 8HP (BODENSEE) 4-stroke (International) Mariner 13.5HP 4-stroke (International) Mercury/Mariner 9.9HP & 15HP (323 cc) Product Features High...
- $55.69
$78.00- $55.69
- Unit price
- per
Mercury 115 HP Outboards Motor Top Cowl Cove Decal Sticker Set 881649A01, 881649A05, 891814A04, 881840A05, 37-881649A01, 823407A00, 803165A00, 804685A00 - JLM Marine
Reference Code JLM Marine 23DC197R / 23DC197B OEM Reference: 881649A01, 881649A05, 891814A04, 881840A05, 37-881649A01, 823407A00, 803165A00, 804685A00 This precision-made outboard motor decal set restores factory identification markings for Mercury marine engines. Compatibility Mercury 115 hp Outboards (1999-2006 models: FourStroke EFI, Optimax, Saltwater series) Mercury...
- $59.00
- $59.00
- Unit price
- per
Mercury 40 HP Outboards Motor Top Cowl Cove Decal Sticker Set 803641A00, 824093A00, 82409316, 897510A02, 82409316 - JLM Marine
Reference Code JLM Marine: 24DC826MR40, 24DC827MB40, 24DC828MR40, 24DC829MB40; Mercury MerCruiser Marine: 803641A00, 824093A00, 82409316, 897510A02, 37-883524A02, 37-826325A01, 826325A01, 830163A00, 37-859270-6, 37-859270-10, 37-859270-11, 803641A99 This replacement outboard motor decal set restores the original appearance of your marine engine. Compatibility 1998-2006 MERCURY 40 hp MANUAL (824093A00)...
- $38.50
- $38.50
- Unit price
- per
Mercury 90 HP Outboards Motor Top Cowl Cove Decal Sticker Set 823417A00, 826321A00, 804857A00, 881841A01 - JLM Marine
Reference Code JLM Marine: 24DC846MR90, 24DC847MB90, 24DC848MR90, 24DC849MB90, 24DC850MR90, 24DC851MB90 Mercury OEM: 823417A00, 826321A00, 804857A00, 881841A01, 881841A03, 891815A04, 881841A05, 804857A05, 856795A00 Restore OEM appearance with this precision-cut outboard motor decal kit for Mercury engines. Compatibility 1999-2006 Mercury 90HP (including JET, Optimax, FourStroke, and Saltwater...
- $54.00
- $54.00
- Unit price
- per
Water Pump Repair Kit for Mercury / Tohatsu Nissan 25-40 HP 361873220
Product Details Mercury Mariner OEM Part Numbers: 853792A07, 853792A1, 853792T01 Tohatsu/Nissan OEM Part Numbers: 361-87322-0, 361873220M, 361873220 Compatible Models Mercury Marine Four-Stroke EFI Engines 25HP Models: Sea Pro (0R051710 & Up) EFI Standard (0R106999 & Up) EFI JET (0R165086 & Up) 30HP Models: EFI...
- $51.50
$55.00- $51.50
- Unit price
- per
Water Pump Impeller kit for Mercury 6 8 9.9 15 HP 47-42038-2 47-420381 47-42038Q02
Product Details: OEM Part Numbers: 47-42038-2, 47-420381, 47-42038Q02, 420381, 420382, 42038Q02. Aftermarket Part Numbers: AM47-420382, 18-3062. Equivalent Part Numbers: GLM 89451, Mallory 9-45309, 9-45309-10, Sierra 18-3062. Compatible Models: Mercury Two-Stroke Engines: 6-15 HP, 8 (Bodensee)(Intern), 13.5 (International). Four-Stroke Engines: 8/ 9.9 HP (2004 &...
- $26.69
$29.00- $26.69
- Unit price
- per
Mercury MerCruiser Stern Drive Engine Red Decals Sticker Kit Set 861431A98 Fit Alpa One Gen Two - JLM Marine
- Red
Reference Code JLM Marine 23DC022R, Mercury MerCruiser Marine 37-861431A98, Mercury MerCruiser Marine 861431A98 Replace faded or illegible markings with this precision-engineered marine engine sticker for clear identification and compliance. Compatibility ALPHA ONE (GEN.II) 1998 AND UP - 0L100040 & Up Product Use Maintains emission-label...
- $22.80
- $22.80
- Unit price
- per
-
Red
-
Blue
13682A90 Mercury MerCruiser Stern Drive Engine Red Decals Sticker Kit Set 37-13682A90 Fit Alpa One - JLM Marine
- Red
Reference Code JLM Marine 23DC023B, Mercury MerCruiser Marine 37-13682A90, Mercury MerCruiser Marine 13682A90 This marine engine sticker set restores OEM identification markings for stern drives and shaft drives. Compatibility R/MR/Alpha One (Sterndrive) 1983-1990 - 6225577 THRU 0F386995 R/MR/Alpha One (Transom Assembly) 1983-1990 - 6216687...
- $22.80
- $22.80
- Unit price
- per
-
Red
-
Blue
Mercury 30 HP Outboards Motor Top Cowl Cove Decal Sticker Set 803640A00, 897510A01, 82409316 - JLM Marine
Reference Code JLM Marine 24DC820MR30 / 24DC822MR30 / 24DC824MR30, Mercury MerCruiser 803640A00, 897510A01, 82409316 Replace faded identification markings on your boat engine with this precision-fit outboard motor decal kit. Compatibility 1998-2006 Mercury 30HP Electric/Manual (RED) 1999-2005 Mercury 30HP FourStroke 2002-2005 Mercury 30HP Outboards (Red)...
- $34.50
- $34.50
- Unit price
- per
Mercury 6 HP Outboards Motor Top Cowl Cove Decal Sticker Set 808522A00, 808522A96, 808522A94, 804769A00, 37-808522A96, 37-808522A94 - JLM Marine
Reference Code JLM Marine: 24DC803MR6, 24DC804MB6, 24DC805MR6 | Mercury MerCruiser: 808522A00, 808522A96, 808522A94, 804769A00, 37-808522A96, 37-808522A94 Restore your engine's original appearance with this precision-fit outboard motor decal set designed as an exact replacement for worn or missing markings. Compatibility Mercury Outboard Engines (1999-2006): 6.0...
- $31.50
- $31.50
- Unit price
- per
Mercury 60 HP Outboards Motor Top Cowl Cove Decal Sticker Set 879753A01, 826313A01, 883526A02, 804704A00 - JLM Marine
Reference Code JLM Marine: 24DC834MR60, 24DC835MB60, 24DC836MR60, 24DC837MB60Mercury MerCruiser Marine: 879753A01, 826313A01, 883526A02, 804704A00, 37-804704A00, 37-826313A01, 8592677, 85927015 This marine engine sticker set provides OEM-specified replacements for Mercury outboard identification decals. Compatibility 1999-2006 Mercury 60 HP · 1999-2006 Mercury 60 HP SeaPro 2002-2004 Mercury...
- $45.50
- $45.50
- Unit price
- per
Carburetor Rebuild Kit for Mercury Mariner 6HP, 8HP, 9.9HP, 10HP, 15HP, 20HP, 25HP Two-Stroke Models (97611)
OEM Part Numbers 1395-811357, 1395-9179, 1395-9377, 1395-9645, 1395-9725, 1395-9761, 1395-97611, 1395-9761-1, 1395-9803, 97611 Compatible Models Mercury Mariner Two-Stroke Engines: 6HP 8HP 9.9HP 10HP (SeaPro, Marathon, XR10, Magnum) 15HP 20HP 25HP Technical Specifications Weight: 26g Package Dimensions: 18x15x2 cm Installation Instructions Make sure the engine...
- $30.50
$59.00- $30.50
- Unit price
- per
Tags: