Mercury 45 (4 CYL.) (9466692 & Up) Outboard Motor Parts Diagram & Catalog – Free PDF Download

by JLM Marine 30 Apr 2025 0 Comments

Mercury 45 (4 CYL.) Outboard Motor Parts Diagram & Catalog – Free PDF Download

Auto-Blend

Below is the parts list for Mercury 45 (4 CYL.) Auto-Blend:

Position No.	Part Name	OEM Number
-	AUTO BLEND ASSEMBLY	130194
1	TANK KIT, Oil	16612
2	HANDLE KIT	13996
3	CAP, Oil Tank	36-16619
4	HARDWARE KIT	16614
5	PLUG KIT, Drain	19-13979
6	DIAPHRAGM KIT	16611
7	BRACKET KIT, Mounting	16620
8	BAND	13993
9	BRACKET, Left	13983
10	BRACKET, Right	13984
11	COVER	16613
12	FILTER/SENSOR KIT, Oil	35-13985
13	FILTER KIT, Fuel	35-18576
14	VINYL TUBE	32-13992
15	STRAINER, Oil	16618
16	CHECK VALVE KIT	21-16615
17	PLATE	16621
18	MODULE KIT	19265
19	BRACKET KIT	16623
20	GASKET KIT	27-16616
21	HARNESS ASSEMBLY, Auto Blend	84-14585A1

Bottom Cowl and Support Brackets

Below is the parts list for Mercury 45 (4 CYL.) Bottom Cowl and Support Brackets:

Position No.	Part Name	OEM Number	Supersedes
1	BOTTOM COWL ASSEMBLY Comment: (Black)	2116-7715A4
1	BOTTOM COWL ASSEMBLY Comment: (Gray)	2116-7715A5
2	COVER, Bottom Cowl Comment: (Electric)	88926F1
3	SCREW, (.250-20 x .750), Plug to Bottom Cowl Comment: (Electric)	10-28636
2A	PLUG, Bottom Cowl Comment: (Manual)	948801
3A	SCREW, (.250-20 x .750), Plug to Bottom Cowl Comment: (Manual)	10-28636
4	STUD, (.250-20/.250-28 x 1.380), Bottom Cowl	16-56766
5	NUT, (1/4-28X7/32), Bottom Cowl Stud	11-8M0207775
6	ELBOW, Tell Tale Hose - Cylinder Block	22-782792
7	HOSE, Tell Tale Hose to Bottom Cowl (14 Inch)	32-7568058
8	NOZZLE, Tell Tale Hose to Bottom Cowl	69791
9	SLEEVE, Tell Tale Nozzle	23-90882
10	TIE STRAP, Tell Nozzle	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
11	CLAMP, Nozzle - Tell Tale	66849
12	SCREW, (#10-16 x .500), Nozzle Clamp to Bottom Cowl	10-48408
13	BRACKET, Rear Support	720201
14	GROMMET, Rear Support Bracket	25-52723
15	MOUNT, Rubber - Rear Support Bracket	60577
16	WASHER, (.255 x .625 x .0312), Rubber Mount	12-69056
17	NUT, (.250-28) Stainless Steel, Rubber Mount	11-29598
18	DRIP TRAY	72466
19	SCREW, (#10-16 x .625) Stainless Steel, Drip Tray to Bottom Cowl	10-48409
20	BOOT, Control Cable	37695
21	LOCKWASHER, (.250) Stainless Steel, Rubber Mount	13-26992
22	SWITCH ASSEMBLY, Stop Comment: (Manual Push Button Switch)	87-69508A31
23	COVER ASSEMBLY, Top Switch Comment: (Manual Push Button Switch)	87-99525A1
24	NUT, Stop Switch Comment: (Manual Push Button Switch)	11-69844
25	WIRE ASSEMBLY, Orange Stop Switch Comment: (Manual Push Button Switch)	84-62190A8
26	CABLE ASSEMBLY (3.375 Inch)	84-88238T01
27	SCREW, (#10-16 x .375), Ground Strap	10-62568
28	BRACKET ASSEMBLY, Front Support	42660A1
29	MOUNT, Rubber - Front Support Bracket	31014
30	LOCKWASHER, (.250) Stainless Steel, Rubber Mount	13-26992
31	NUT, (.250-28) Stainless Steel, Rubber Mount	11-29598
32	SCREW, (.312-18 x 1.00) Stainless Steel, Front Support Bracket to Bottom Cowl	10-37562
33	SWITCH ASSEMBLY, Mercury Comment: (Manual)	58124A20
33	SWITCH ASSEMLBY, Mercury Comment: (Electric)	87-33386A3
34	SCREW, (.190-24 x .500), Switch to Front Bracket (0.50 Inch)	10-69235
35	PIN, Roll, Mercury Switch	17-36242
36	TERMINAL BLOCK Comment: (Manual Only)	86-45915
37	SCREW, (.190-24 x .62), Terminal Block to Front Bracket Comment: (Manual Only)	10-20411
38	SCREW, (#10-16 x .440), Harness Leads Comment: (Manual Only)	10-69079
39	SWITCH ASSEMBLY, Neutral Start Comment: (Use with Electric Tiller Handle Models)	87-74605A4
40	SCREW, (#4-40 x .750) Comment: (Use with Electric Tiller Handle Models)	10-64332
41	NUT, , Switch Screw Comment: (Use with Electric Tiller Handle Models)	4-40,11-24832
42	ACTUATOR Comment: (Use with Electric Tiller Handle Models)	97411
43	SPRING, Interlock Actuator Comment: (Use with Electric Tiller Handle Models)	24-88099
44	SCREW, (.190-32 x 1.00), Actuator to Front Bracket Comment: (Use with Electric Tiller Handle Models)	10-37892
45	WASHER, Actuator Screw Comment: (Use with Electric Tiller Handle Models)	12-22887
46	SPACER, Actuator Screw Comment: (Use with Electric Tiller Handle Models)	23-88100
47	NUT, Stainless Steel, Actuator Screw Comment: (Use with Electric Tiller Handle Models)	10-32,11-859124	11-45812 (Use with Electric Tiller Handle Models)

Carburetor Assembly

Below is the parts list for Mercury 45 (4 CYL.) Carburetor Assembly:

Position No.	Part Name	OEM Number	Supersedes
1	CARBURETOR ASSEMBLY Comment: (Upper)	1367-6517A63
1	CARBURETOR ASSEMBLY Comment: (Lower)	1367-6517A64
2	NOT SOLD SEPARATE, Large Body Channel	NSS
3	NOT SOLD SEPARATE, Body Channel	NSS
4	SHAFT ASSEMBLY, Choke	1395-9296A1
5	NOT SOLD SEPARATE, Return-Throttle Shaft	NSS
6	BAFFLE, Fuel Bowl	814483	1399-7211A 1
7	FLOAT	1395-9293
8	NOT SOLD SEPARATE, Float Retaining	NSS
9	BOWL, Fuel	1399-5127
10	NOT SOLD SEPARATE, Fuel Bowl	NSS
11	SCREW, Fuel Bowl to Carburetor	1395-9652
12	NOT SOLD SEPARATE, Fuel Bowl Screw	NSS
13	NEEDLE AND SPRING, Inlet	1395-9022
14	JET, Main Fuel (.057)	1399-1457
15	JET, (.098), Economizer (.098)	1395-7335
16	VENTURI	64677
17	SHUTTER, Choke	1399-8665
18	NOT SOLD SEPARATE, Choke Shutter to Choke Shaft	NSS
19	NOT SOLD SEPARATE, Idle Mixture	NSS
20	NOT SOLD SEPARATE, Idle Mixture Screw	NSS
21	NOT SOLD SEPARATE, Fuel Pump	NSS
22	COVER, Plate (Upper Carburetor)	1395-9653
23	COVER, Plate (Lower Carburetor)	1395-9654
24	SCREW, Strainer Body to Carburetor	1395-808612	1399-5132
25	SHAFT, Throttle Comment: (Upper Carburetor)	1395-9020
25	SHAFT, Throttle Comment: (Lower Carburetor)	1395-9656
26	LEVER, Throttle (Upper Carburetor)	92880
27	SCREW, Throttle Lever (Upper Carburetor)	1395-6027
28	LEVER, Throttle (Lower Carburetor)	8146791
29	SCREW, Throttle Lever (Lower Carburetor)	1395-6027
30	SHUTTER, Throttle	1395-9649
31	NOT SOLD SEPARATE, Throttle Shutter to Throttle Shaft	NSS
32	GASKET, Carburetor Flange	27-757911
33	NUT, Carburetor Mounting Stud	11-64809
--	REPAIR KIT	1395-9650
--	GASKET SET	1395-9651

Carburetor Linkage/Choke Solenoid

Below is the parts list for Mercury 45 (4 CYL.) Carburetor Linkage/Choke Solenoid:

Position No.	Part Name	OEM Number	Supersedes
1	SOLENOID ASSEMBLY, Choke Comment: (Electric)	89-889274	54293A11 (Electric)
2	LOCKWASHER, Stainless Steel, Choke Solenoid Terminal Comment: (Electric)	10,13-26996
3	NUT, Brass, Choke Solenoid Terminal Comment: (Electric)	10-32,11-45076
4	SCREW, (.312-24 x 1.75), Choke Solenoid to Front Bracket Comment: (Electric)	10-26066
5	LOCKWASHER, (.312), Choke Solenoid Screw Comment: (Electric)	13-8M0204647
6	NUT, (.312-24), Choke Solenoid Screw Comment: (Electric)	11-22053
7	PLUNGER ASSEMBLY, Choke Solenoid Comment: (Electric)	56074A8
8	KNOB, Choke Comment: (Manual)	90241
9	KNOB ASSEMBLY Comment: (Electric)	90242A1
10	SCREW, (#10-16 x .500), Strap to Choke Knob Comment: (Electric)	10-35519
11	STRAP, Choke Knob to Choke Rod Comment: (Electric)	49589
12	SCREW, (#10-16 x .375), Strap to Choke Rod Comment: (Electric)	10-62568
13	GROMMET, Choke Knob	25-20116
14	ROD ASSEMBLY, Choke	85966A1
15	SCREW, Choke Rod	10-77614A1
16	SPRING, Choke Rod Comment: (Electric)	24-60288
17	BRACKET ASSEMBLY, Pick Up	53719A2
18	SCREW, (#8-32 x .790), Pick-Up Bracket	10-66104
19	KEY, Coupling	28-89694
20	LINE, (57.00 Inches Bulk), Carburetor to Tee to Carburetor Comment: (2 Inch)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821 (2 Inch)
21	TIE STRAP, Fuel Line	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
22	TEE, Plastic, Fuel Line	22-73318

Clamp Bracket Assembly(Non Power Trim)

Below is the parts list for Mercury 45 (4 CYL.) Clamp Bracket Assembly(Non Power Trim):

Position No.	Part Name	OEM Number	Supersedes
1	CLAMP BRACKET ASSEMBLY Comment: (Manual)	1440-8394A2
1	CLAMP BRACKET ASSEMBLY, Black Comment: (Electric)	1440-8394A1
1	CLAMP BRACKET ASSEMBLY, Gray Comment: (Electric)	1440-8394A3
2	THUMB SCREW ASSEMBLY Comment: (Manual)	10-90470A3
2	THUMB SCREW ASSEMBLY Comment: (Electric)	10-78492A1
3	WASHER, Thumb Screw	12-78493
4	SCREW, Washer to Thumb Screw	10-78495
5	CAP, Thumb Screw	75043
6	TILT TUBE	8M0041936	8M0035074, 883067, 30664 2, 74528
7	WASHER, Tilt Tube	12-52864
8	NUT, (.875-14), Tilt Tube	11-858869	11-30499
9	CAP, Plastic - Tilt Tube	53078
10	PIN, Upper Shock Comment: (With Shock Absorber)	55-28416
11	BUSHING, Clamp Bracket	23-73203
12	SPACER, Clamp Bracket Stud	23-59623
13	STUD, Clamp Bracket	16-59625
14	LOCKWASHER, (.312), Clamp Bracket Stud	13-8M0204647
15	NUT, (.312-24) Stainless Steel, Clamp Bracket Stud	11-28770
16	PIN ASSEMBLY, Tilt Lock	17-8M0026068	17-49930A 1
18	BOLT, (.375-16 x 3.250), Clamp Bracket to Tramsom (3.25 Inch)	10-68298
19	WASHER, Clamp Bracket Bolt	12-68410
18	SCREW, (.375-16 x 5.00), Clamp Bracket to Transom (5 Inch)	10-89673
19	WASHER, (1-1/ 4 x 25/64 x .125 SS), Clamp Bracket Bolt	12-28420
19	WASHER, (..88 x .39 x .06), Clamp Bracket Bolt	12-68300
20	NUT, Clamp Bracket Bolt	11-82671112
21	SHOCK ABSORBER, Black Comment: (With Shock Absorber)	55-58780A7
21	SHOCK ABSORBER, Gray Comment: (With Shock Absorber)	55-58780A4
22	PIN, Lower Shock Comment: (With Shock Absorber)	55-696531
23	WASHER, (.766 x 1.312 x .125), Upper Bushing Retainer (Inner) Comment: (With Shock Absorber)	12-34937
24	WASHER, Lower Bushing Retainer (Inner) Comment: (With Shock Absorber)	12-59378
25	BUSHING, Rubber - Shock Absorber (Upper) Comment: (With Shock Absorber)	23-32171
26	BUSHING, Rubber - Shock Absorber (Lower) Comment: (With Shock Absorber)	23-28198
27	WASHER, Upper and Lower Bushing (Outer) Comment: (With Shock Absorber)	12-69374
28	SCREW, (.500-20 x .625), Upper and Lower Shock Pin (0.625 Inch) Comment: (With Shock Absorber)	10-69375A1
29	STRAP, Tilt Stop Comment: (Without Shock Absorber)	98876
30	PIN, Lower Shock Mount Comment: (Without Shock Absorber)	98878
31	SPRING Comment: (Without Shock Absorber)	24-98875
32	COTTER PIN Comment: (Without Shock Absorber)	18-8M0214922
33	SHOCK MOUNT, Upper Comment: (Without Shock Absorber)	98877

Cowling

Below is the parts list for Mercury 45 (4 CYL.) Cowling:

Position No.	Part Name	OEM Number
1	TOP COWL ASSEMBLY, Without Decal Comment: (Manual) (Black)	2153-7938
1	TOP COWL ASSEMBLY, Without Decal Comment: (Electric) (Black)	2153-7937A8
1	TOP COWL ASSEMBLY, Without Decal Comment: (Manual) (Gray)	2153-7938F4
1	TOP COWL ASSEMBLY, Without Decal Comment: (Electric) (Gray)	2153-7937F4
2	HOOK, Top Cowl Latch - Rear	55455
3	SCREW, (.250-28 x .880), Rear Hook to Top Cowl	10-22956
4	LOCKWASHER, (.250) Stainless Steel, Rear Hook Screw	13-26992
5	SHIELD, Rear - Top Cowl	37690
6	SCREW, (#10-16 x .625) Stainless Steel, Rear Shield to Top Cowl	10-48409
7	RETAINER ASSEMBLY, Top Cowl	97447A1
8	SCREW, (.312-18 x .880), Retainer to Top Cowl	10-53167T
9	LOCKWASHER, (.312-24), Retainer Screw	13-39107
10	LEVER, Cowl Latch Hinge	94918F1
11	HINGE, Cowl Latch-Top Cowl	52739
12	PIN, Cowl Latch Lever to Hinge	17-58998
13	FRONT COVER MERCURY, Without Decal Comment: (Black)	2182-7927A5
13	FRONT COVER MARINER, Without Decal Comment: (Gray)	2182-7927A19
14	KNOB, Cowl Front Cover	56849
15	WASHER, Cover Knob	12-30771
16	WASHER, Cover Knob	12-59572
17	SPRING, Tension - Cover Knob	24-30772
18	PIN, Roll, Tension Spring to Knob	17-29077
19	BLANKET, Sound	38674
20	PAD, Sound	94923
21	TOP COWL ASSEMBLY, Wrap Around - Mercury, Without Decal Comment: (Black)	2118-3247A3
21	TOP COWL ASSEMBLY, Wrap Around - Mariner, Without Decal Comment: (Gray)	2172-8181A4
22	LATCH ASSEMBLY, Cowl	46785A1
23	HOOK, Cowl Latch	30413

Crankshaft, Pistons, and Connecting Rods

Below is the parts list for Mercury 45 (4 CYL.) Crankshaft, Pistons, and Connecting Rods:

Position No.	Part Name	OEM Number	Supersedes
1	CRANKSHAFT	459-9075T
2	KEY, Woodruff, Crankshaft	28-20094
3	BEARING ASSEMBLY, Main, Valve Type	534-3267T25
4	PIN, Dowel, Main Bearing	17-20032
5	PIN, Dowel, Reed Locating	17-65855
6	SCREW, (#12-28 x .560) , Main Bearing (0.563 Inch)	10-45775
7	NUT, Main Bearing Screw	11-45774
8	REED SET, Matched	34-88498A1
9	STOP, Reed	34-822839	34-79014
10	SCREW, (.190-32 x .560), Reed Stop (0.563 Inch)	10-77280
11	NUT, , Reed Stop Screw	10-32,11-20110
12	PISTON ASSEMBLY Comment: (Standard)	780-9229A7
12	PISTON ASSEMBLY Comment: (.015 Oversize)	780-9229A10
12	PISTON ASSEMBLY Comment: (.030 Oversize)	780-9229A11
13	LOCK RING, Piston Pin	40-828119	40-47276
14	RING SET, Piston - Standard Comment: (Standard)	39-27841A12
14	RING SET, Piston Comment: (.015 Oversize)	39-28616A12
14	RING SET, Piston - .030 Oversize Comment: (.030 Oversize)	39-89822A12
15	CONNECTING ROD ASSEMBLY	632-7621A3
16	SCREW, (.250-28 Special), Cap to Rod	10-91012
18	BEARING, Needle, Piston Pin	29-20063
19	WASHER, Needle Locating	12-47275
20	BEARING, Needle, Crankpint	29-20046T
21	BEARING ASSEMBLY, Center Main	547-7060A2
22	PIN, Dowel, Center Main Bearing	17-20032
23	BEARING, Needle	29-714221
24	RACE, Outer	26113T
25	RING, Snap, Outer Race	53-26933
26	SCREW, (.250-20 x 1.00), Center Main Bearing (1 Inch)	10-8M0214943

Cylinder Block and Crankcase Assembly

Below is the parts list for Mercury 45 (4 CYL.) Cylinder Block and Crankcase Assembly:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER BLOCK ASSEMBLY	863-8981A6
2	BRACKET, Upper Starter Motor	72038
3	SCREW, (.312-18 x 1.880), Bracket to Crankcase (1.875 Inch)	10-73279
4	LOCKWASHER, (.312), Bracket Screw	13-8M0204647
5	COVER, Lower Starter Motor	76867
6	SCREW, (.312-18 x 1.880), Cover to Crankcase (1.875 Inch)	10-73279
8	PIN, Dowel, Cylinder block to main bearing	17-20032
9	STUD, Carburetor (1.25 Inch)	16-64936
10	STUD, Crankcase to Driveshaft Housing (1.625 Inch)	16-68165
11	PIN, Dowel, Crankcase to Cylinder Block	17-43044
12	STUD, Cylinder block to drive shaft housing (4 Inch)	16-87901
13	STUD, (.312 x 2.125), Cylinder block to drive shaft housing (2.125 Inch)	16-68166
14	STUD, (.312-18/.312-24 x 2.560), Cylinder block to drive shaft housing (2.50 Inch)	16-68167
15	SCREW, (.312-18 x 1.50), Crankcase to cylinder block (1.50 Inch)	10-73657
15	SCREW, (.312-18 x 1.375), Crankcase to cylinder block (1.375 Inch)	10-31984
15	SCREW, (.312-18 x 2.88), Crankcase to cylinder block (2.875 Inch)	10-73275
16	WASHER, (.323 x .563 x .063) Stainless Steel, Crankcase Screw	12-8M0042642	12-70132
17	SCREW, (.375-16 x 1.00) Comment: (Center Main Bearing Locking)	10-20359
17	SCREW, (.375-16 x .620) Comment: (Main Bearing Locking) (0.625 Inch)	10-98260
18	TAB WASHER, Center Bearing Locking Screw	14-20091
19	LINE, (57.00 Inches Bulk), Balance - Main Bearing (5.50 Inch)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
20	ELBOW, Balance Tube to Cylinder Block	22-996642
21	CONNECTOR, Upper Bleed Hose	22-56759
22	HOSE, Cylinder Bleed (11 Inch)	32-9938779
23	CHECK VALVE, Lower Bleed Hose	21-428671
24	INDICATOR, Timing Comment: (Electric)	99156
25	SCREW, (.312-18 x .750) Stainless Steel, Indicator to Crankcase Comment: (Electric)	10-39349
26	LOCKWASHER, (.312), Indicator Screw Comment: (Electric)	13-8M0204647
-	POWERHEAD ASSEMBLY, Complete Comment: (Incluses Cylinder Block and Crankcase, Pistons, Connecting Rods and Bearings, ETC.)	97469T87

Driveshaft Housing Assembly

Below is the parts list for Mercury 45 (4 CYL.) Driveshaft Housing Assembly:

Position No.	Part Name	OEM Number	Supersedes
1	HOUSING ASSEMBLY, Driveshaft (Short Shaft) Comment: (Non Power Trim)	1592-8188A8
1	HOUSING ASSEMBLY, Driveshaft (Long Shaft) Comment: (Non Power Trim)	1593-7513A12
1	HOUSING ASSEMBLY, Driveshaft, Black Comment: (Non Power Trim)	1593-8189A10
1	HOUSING ASSEMBLY, Driveshaft, Gray Comment: (Non Power Trim)	1593-8189A11
3	PLUG, Plastic - Trim Tab Screw Hole	19-64649
4	STUD, (.375-16/.375-24 x 1.750), Driveshaft Housing	16-8M0022145	16-57932
5	STUD, Driveshaft Housing (3 Inch)	16-57935
6	WASHER, Gear Housing Studs (0.438 Inch)	12-65791
7	NUT, (.437-20) Stainless Steel, Gear Housing Studs	11-8M0204653
8	MOUNT, Rubber - Upper	923373
9	SEAL, Upper Mount	96401
10	WASHER, Upper Mount Bolt (37/64 I.D.)	12-27727
11	WASHER, Rubber - Upper Mount Bolt	12-66966
12	WASHER, Upper Mount Bolt	12-30514
13	NUT, (.437-20) Stainless Steel, Upper Mount Bolt	11-8M0204653
14	COVER, Upper Mount	87883
15	SCREW, (.250-20 x 1.00), Upper Mount Cover	10-8M0214943
16	WASHER, (.281 x .500 x .060) Stainless Steel, Upper Mount Cover Screw	12-8M0204649
17	COVER, Trim - Driveshaft Housing Comment: (Black)	37687
17	COVER, Trim - Driveshaft Housing Comment: (Gray)	37687F2
18	SCREW, (#10-16 x .750) Stainless Steel, Trim Cover to Driveshaft Housing	10-57807
19	GROMMET, Trim Cover Screw	25-92012
20	SEAL, Trim Cover to Driveshaft Housing	38157
21	STRIP, Retaining - Trim Cover Seal (Rear)	38158
22	STRIP, Retaining - Trim Cover Seal (Side)	38154
23	SCREW, (#10-16 x .500), Retaining Strip	10-48408
24	TUBE, Exhaust Comment: (Short Shaft)	695431
24	TUBE, Exhaust Comment: (Long Shaft)	695441
25	TUBE, Water Inlet Comment: (Short Shaft)	32-37727
25	TUBE, Water Inlet Comment: (Long Shaft)	32-45679
26	NUT, Powerhead Studs (0.313 Inch)	11-64809
27	MOUNT, Rubber - Lower	75304T1
28	SCREW, (.500-20 x 5.500), Lower Mount Screw Comment: (Non Power Trim)	10-75284
28	SCREW, Lower Mount Screw Comment: (Power Trim)	10-43426
29	WASHER, Lower Mount Screw	12-28051
30	WASHER, Rubber - Lower Mount Screw	12-28053
31	WASHER, (.875 Inch Outside Diameter), Lower Mount Screw	12-30119
32	NUT, Lower Mount Screw	11-25096
33	CLAMP, Lower Mount	69592F1
34	SCREW, (.312-18 x .875), Lower Mount Clamp	10-29256
35	SPRING, Tension - Lower Mount Clamp	24-35522
36	COVER, Lower Mount Clamp Comment: (Black)	35474T
36	COVER, Lower Mount Clamp, Lower Mount Clamp Comment: (Gray)	35474F2
37	SCREW, (#12-14 x .920), Cover to Lower Mount Clamp	10-87884
38	NUT, Lower Mount Clamp Cover	11-35521
39	CABLE ASSEMBLY, Ground, Quanity of Two on Power Trim	88238A10

Electric Components

Below is the parts list for Mercury 45 (4 CYL.) Electric Components:

Position No.	Part Name	OEM Number	Supersedes
1	RECTIFIER	8M0058226	816770T, 816770, 62351A 1, 83-70350A 1, 83-70350A 3
2	NUT, Brass, Rectifier Terminal	10-32,11-45076
3	SCREW, (.190-24 x .62), Rectifier to Switch Box Plate	10-20411
4	STARTER MOTOR ASSEMBLY	50-898265005	50-73521T
5	STOP, Rubber - Starter Motor	8M0043376	68042
6	COLLAR, Rubber - Starter Motor Mount	23-8M0034918	23-8M0001391, 56703
7	HOLDER, Fuse	134731
8	WIRE, Starter Motor/Soleniod (Yellow)	84-93389A1
9	NUT, (.250-20), Wire to Starter Motor	11-64015
10	CABLE ASSEMBLY, Black, Starter Motor/Bracket (Black)	84-93388A14
11	SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel, Wire to Starter Motor	10-69035
12	SOLENOID, Starter	8M0185622
13	NUT, Brass, Soleniod Terminal	8-32,11-26419
14	NUT, (.250-20) Brass, Solenoid Terminal	11-94330
15	SCREW, (.250-20 x .500) Stainless Steel, Soleniod to Support Bracket	10-41508
16	LOCKWASHER, (.250) Stainless Steel, Starter Solenoid Screw	13-26992
17	INSULATOR, Starter Solenoid	85-97861
18	HARNESS ASSEMBLY	84-96277A4
19	FUSE, 20 Ampere	88-8M0207796
20	CABLE ASSEMBLY, Fuse	84-95084A2
21	CLAMP, Wiring Harness	88751
22	SPRING, Wiring Harness	24-28357
23	SCREW, (.190-32 x 1.12), Wiring Harness Clamp	10-23702
24	WASHER, (.203 x .562 x .060) Stainless Steel, Wiring Harness Clamp Screw	12-72761
25	CABLE ASSEMBLY, Positive - Battery	84-88439A3
25	CABLE ASSEMBLY, Battery - Negative	84-88439A4

End Caps and Exhaust Cover

Below is the parts list for Mercury 45 (4 CYL.) End Caps and Exhaust Cover:

Position No.	Part Name	OEM Number	Supersedes
2	END CAP ASSEMBLY, Upper	1160-5826A2
3	SEAL, Upper End Cap	26-41953
4	O-RING, Upper End Cap	25-20081
5	BEARING, Ball, Upper End Cap	30-63742T
6	SHIM, Upper End Cap (.005-10)	15-72538A1
7	SCREW, Upper End Cap (0.75 Inch)	10-824941	10-59645, 10-73274
8	COVER ASSEMBLY, Cylinder Block	1017-8360A1
9	PLUG, Pipe (.125-27), Cylinder Block Cover Comment: (Manual Only)	22-328022
10	GASHET, Cylinder Block Cover	27-437772
11	SCREW, Cylinder Block Cover (1 Inch)	10-8M0214943
12	CABLE ASSEMBLY	46933A7
14	MOUNT, Rubber - Cylinder Block Cover	90435
15	NUT, (1/4-28X7/32), Rubber Mount	11-8M0207775
16	COVER ASSEMBLY, Transfer Port	18827A1
17	GASKET, Transfer Port Cover	27-279361
18	SCREW, Transfer Port Cover (0.625 Inch)	10-20540
19	END CAP ASSEMBLY, Lower	1158-6635T1
20	O-RING, Lower End Cap	25-20081
21	SEAL, Lower End Cap	26-41953
22	BEARING, Ball, Lower End Cap	30-63742T
23	SHIM SET, Lower End Cap (.005-10)	15-20085A1
24	SCREW, (.312-18 x .875), Lower End Cap	10-29256
25	MOUNT, Rubber - Crankcase	90435
26	NUT, (1/4-28X7/32), Rubber Mount	11-8M0207775
28	GASKET, Cylinder Block to Baffle Plate	27-854913
29	PLATE, Baffle - Exhaust Manifold	90421T01
30	GASKET, Baffle Plate to Exhaust Cover	27-854924
31	COVER, Exhaust Manifold	77381
32	SCREW, (.312-18 x 1.00) Stainless Steel, Manifold Cover to Cylinder Block	10-37562
32	SCREW, (.312-18 x 1.12), Manifold Cover to Cylinder Block	10-38837
33	TERMINAL BLOCK Comment: (Electric Only)	86-45915
34	SCREW, (#10-16 x .375), Terminal Block Comment: (Electric Only)	10-62568
35	SCREW, (#10-24 x .50), Terminal Block Comment: (Electric Only)	10-72169
36	SWITCH ASSEMBLY, Temperature, 260 Tan Comment: (Electric Only)	87-96829A1
36	TEMPERATURE SWITCH, 300 Tan and Green Comment: (Electric Only)	87-16775A1
-	GASKET SET	27-85491A90

Exhaust Plate and Shift Linkage

Below is the parts list for Mercury 45 (4 CYL.) Exhaust Plate and Shift Linkage:

Position No.	Part Name	OEM Number
1	PLATE ASSEMLBY, Exhaust Extension	42819A2
2	BUSHING, Exhaust Extension Plate	23-27132
3	WASHER, Nylon - Water Inlet Tube	12-38453
4	SEAL, Rubber - Water Tube	26-38452
5	HOUSING, Water Inlet Tube Seal	79799
6	GASKET, Housing	27-797971
7	SCREW, (#10-32 x 1.380), Housing to Exhaust Plate (1.375 Inch)	10-79798
8	GASKET, Powerhead	27-796501
9	SHIFT SHAFT ASSEMBLY, Upper Short Shaft	76632A3
9	SHIFT SHAFT ASSEMBLY, Upper Long Shaft	76632A4
10	BARREL, Nylon - Upper Shift Shaft	8M0221994
11	ACTUATOR ASSEMBLY, Shift Control	74739A3
12	SPRING, Shift Cable	24-37934
13	SCREW, Spring to Actuator	10-38069
14	BEARING, Nylon - Shift Control Actuator	37932
15	SCREW, (.250-28 x 1.00), Bearing to Shift Control Actuator	10-36137
16	LOCKWASHER, (.250), Bearing Screw	13-21272
17	RAIL, Shift Control Bearing	37935
18	SCREW, (.250-28 x .750) Stainless Steel, Rail to Exhaust Manifold Cover	10-69028
19	LOCKWASHER, (.250) Stainless Steel, Rail Screw	13-26992
20	LEVER, Throttle and Shift Cables	59037A2
21	PIN, Roll - Quick Disconnect Lever	17-239281
22	SPRING, Quick Disconnect Lever	24-38005
23	BUSHING, Nylon, Nylon - Quick Disconnect Lever	23-37927
24	RETAINER, Nylon Bearing	37926
25	SCREW, (.250-28 x 1.250), Bearing Retainer	10-37923
26	GASKET, Exhaust Extension Plate	27-385011
27	SEAL, Rubber - Exhaust Extension Plate	38156
28	STRIP, Rubber Seal	99136
29	SCREW, (.190-32 x .500), Retaining Strip	10-37571
-	GASKET SET	27-85491A90

Flywheel, Ignition Coil and Switch Box

Below is the parts list for Mercury 45 (4 CYL.) Flywheel, Ignition Coil and Switch Box:

Position No.	Part Name	OEM Number	Supersedes
1	PLUG, Yellow, Flywheel	19-45907
2	NUT, (.625-18), Flywheel	11-8M0214915
3	WASHER, (.641 x 1.250 x .190), Flywheel Nut	12-33001
4	FLYWHEEL ASSEMBLY Comment: (Manual)	248-8722A16
4	FLYWHEEL ASSMEBLY Comment: (Electric)	248-8722A17
5	SCREW, (.250-28 x .625), Flexible Plate to Flywheel	10-32417
6	RATCHET, Flywheel (Manual)	50-88755
7	SCREW, (.312-24 x .750), Ratchet to Flywheel (Manual)	10-68997
8	STATOR Comment: (Manual)	398-832074A6
8	STATOR Comment: (Electric)	398-832075A20	398-832075A14, 398-5454A25, 398-5454A63, 398-818535A15 (Electric)
9	SCREW, (#10-24 x .880), Stator to Upper End Cap	10-75840
10	TRIGGER ASSEMBLY	96452A4
13	HARNESS ASSEMBLY, Switch Box to Ignition Coil	84-88721A1
14	COIL ASSEMBLY, Ignition	339-832757A4
15	NUT, Brass, Ignition Coil Terminals	10-32,11-45076
16	CABLE ASSEMBLY, Coil to Switch Box	84-60466A19
17	COVER, Ignition Coil	87554
18	SCREW, (.190-32 x 2.00), Coil Cover Comment: (10-32 X 2 Inch)	10-88856
19	WASHER, (.192 x .375 x .0312) Stainless Steel, Coil Cover Screw	12-30164
20	LEAD ASSEMBLY, Spark Plug	84-813715A5
21	BOOT/TERMINAL KIT	85-63709A1
22	BOOT, Ignition Coil	332-2854T01
23	SPARK PLUG Comment: (USA Models)	33-896329833	33-833C (USA Models)
23	SPARK PLUG, (NGK-BUZHW) Comment: (Belgium and Canada Models)	33-14103550
24	SWITCHBOX ASSEMBLY	332-5772A7
25	SCREW, (#12-24 x 1.25), Switch Box and "J" Clip to Plate	10-20619
26	J CLIP, Switch Box Leads	54-8M0024808
27	NUT, Brass, Switch Box Terminals	10-32,11-45076
28	PLATE, Switch Box	88322
29	SCREW, (.250-20 x .625), Switch Box Plate to Cylinder Block	10-54615
30	TERMINAL BLOCK	86-638131
31	SCREW, (.190-24 x .62), Terminal Block	10-20568
31	SCREW, (#10-16 x .375), Terminal Block	10-62568

Fuel Pump

Below is the parts list for Mercury 45 (4 CYL.) Fuel Pump:

Position No.	Part Name	OEM Number	Supersedes
1	PUMP ASSEMBLY, Fuel	14360A78
2	DIAPHRAGM KIT	21-857005A1
3	NOT SOLD SEPARATE, Check Valve - Rubber	NSS
4	NOT SOLD SEPARATE, Gasket - Boost	NSS
5	NOT SOLD SEPARATE, Diaphragm	NSS
6	NOT SOLD SEPARATE, Gasket - Pulse	NSS
7	NOT SOLD SEPARATE, Spring	NSS
8	NOT SOLD SEPARATE, Cap	NSS
9	NOT SOLD SEPARATE, Disc - Rubber	NSS
10	NOT SOLD SEPARATE, Retainer	NSS
13	GASKET, Base	27-8M0204705
14	BASE, Fuel Pump	144303
15	PLATE, Fuel Pump	98775A4
16	PLUG, (1/8 Inch Brass)	22-390721
17	FITTING	22-99498
18	SCREW, (M5 x 40), Fuel Pump	10-4000310
19	SCREW, (#12-24 x 2.00), Fuel Pump to Crankcase	10-16452
20	TUBING	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
21	FILTER, Fuel	35-816296Q2
22	TIE STRAP, Fuel Tubing	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
23	CONNECTOR, Fuel Comment: (Metal Connector)	22-15781A10
24	GROMMET, Fuel Connector Comment: (Metal Connector)	25-14579
25	SCREW, (.250-28 x 2.00), Fuel Connector Comment: (Metal Connector)	10-67916
26	WASHER, Fuel Connector Screw Comment: (Metal Connector)	12-71055
27	NUT, (.250-28) Stainless Steel, Fuel Connector Screw Comment: (Metal Connector)	11-35888
23	CONNECTOR, Fuel Comment: (Plastic Connector)	22-816856Q3
24	GROMMET, Fuel Connector Comment: (Plastic Connector)	25-15102001
25	SCREW, (.250-28 x 1.750), Fuel Connector Comment: (Plastic Connector)	10-69029
27	NUT, Fuel Connector Screw Comment: (Plastic Connector)	11-36069
28	FITTING, Fuel Line	22-64705
29	LINE, (57.00 Inches Bulk)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
30	CLAMP, Fuel Filter	54-633001
31	J CLIP, Fuel Line	54-8M0024808
32	HOSE	32-18164
-	GASKET SET	27-85491A90

Gear Housing(Driveshaft)

Below is the parts list for Mercury 45 (4 CYL.) Gear Housing(Driveshaft):

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Short Shaft - Black	1643-9539A4
-	GEAR HOUSING ASSEMBLY, Long Shaft - Black	1643-9539A5
-	GEAR HUSING ASSEMBLY, Short Shaft - Gray	1643-9539A6
-	GEAR HOUSING ASSEMBLY, Long Shaft - Gray	1643-9539A7
1	GEAR HOUSING ASSEMBLY Comment: (Black)	1643-9539T1
1	GEAR HOUSING ASSEMBLY Comment: (Gray)	1643-9539T8
2	CONNECTOR ASSEMBLY, Speedometer	22-85822A10
3	PIN, Dowel (.187 x .530), Gear Housing	17-8M0084726	17-85500
4	STUD, Water Pump/Base (2.625 Inch)	16-33778
5	STUD, (.437-14/.437-20 x 2.190), Gear Housing	16-8M0034453	16-57933
6	BEARING, Roller, Driveshaft	31-62091T
7	SCREEN ASSEMBLY, Water Intake	72849A1
8	SCREW, (#10-32 x 1.250), Water Intake Screen to Gear Housing	10-36070
9	NUT, Stainless Steel, Water Intake Screen Screw	10-32,11-859124	11-45812
10	PLATE, Support - Exhaust Tube	92815
11	SEAL, Exhaust Tube	37721001
12	GEAR, Pinion, Driveshaft	43-98097T
13	NUT, (.437-20), Pinion Gear to Driveshaft	11-55910
14	GASKET, Water Pump Base	27-19552
15	O-RING	25-26722
16	BASE ASSEMBLY, Water Pump	46-77177A1
17	SEAL, Oil	26-79831
18	SEAL, (1.254 x .312)	26-90562
19	PIN, Dowel	17-35973
20	GASKET, Lower	27-19553
21	FACE PLATE	32768
22	GASKET, Upper	27-19551
23	IMPELLER	47-89983T
24	KEY, Impeller Drive	28-8M0032837	28-56662
25	BODY ASSEMBLY, Water Pump	46-77822A1
26	INSERT	48753
27	SEAL, Rubber	26-38452
28	WASHER, Nylon	12-38453
29	WASHER, (.281 x .500 x .060) Stainless Steel, Water Pump Body and Base Studs	12-8M0204649
30	NUT, (.250-28), Water Pump Body and Base Studs	11-8267119
31	O-RING, Rubber	25-20273
32	SEAT ASSEMBLY, Driveshaft	78654A1
33	SEAL, Splined - Driveshaft	86304
34	SCREW, (.375-16 x .250), Grease Filler	10-79953Q04
35	SCREW, Magnetic, Drain	22-8M0058389	22-67892A06
36	WASHER, Fiber, Filler/Drain Screw	12-191833
37	SLEEVE, Lubrication - Driveshaft	88181
38	SHIM SET, Bearing to Gear Housing(.002-3-5-10-20)	15-92881A1
39	BEARING ASSEMBLY, Roller, Tapered - Driveshaft	31-8M0166756
40	DRIVESHAFT ASSEMLBY Comment: (Short Shaft)	45-98179
40	DRIVESHAFT ASSEMBLY Comment: (Long Shaft)	45-98180
41	SPRING, Compression - Driveshaft	24-20254
42	PIN, Driveshaft	17-30545
43	SHAFT ASSEMBLY, Shift	76063A1
44	E RING, Shift Shaft	53-29641
45	O-RING, (.862 x .103), Shift Shaft Bushing	25-25439
46	BUSHING ASSEMBLY, Shift Shaft	23-77631A2
47	SEAL, Oil, Shift Shaft Bushing	26-8M0204708
48	WASHER, Rubber - Shift Shaft Bushing	12-77674
49	BASE, Reverse Locking Comment: (Non Power Trim)	78036
50	CAM, Reverse Locking Comment: (Non Power Trim)	43308T1
-	WATER PUMP KIT	46-77177A3
-	SEAL KIT	26-79831A1
-	GASKET SET	27-85491A90

Gear Housing, Propeller Shaft

Below is the parts list for Mercury 45 (4 CYL.) Gear Housing, Propeller Shaft:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Short Shaft - Black	1643-9539A4
-	GEAR HOUSING ASSEMBLY, Long Shaft - Black	1643-9539A5
-	GEAR HUSING ASSEMBLY, Short Shaft - Gray	1643-9539A6
-	GEAR HOUSING ASSEMBLY, Long Shaft - Gray	1643-9539A7
1	GEAR HOUSING ASSEMBLY Comment: Black	1643-9539T1
1	GEAR HOUSING ASSEMBLY Comment: Gray	1643-9539T8
51	CAM, Shift Control	760394
52	SHIM SET, Bearing Cup to Gear Housing (.002-3-5-10)	15-38374A1
53	BEARING SET	31-38356A1
54	GEAR ASSEMBLY, Forward	43-55608T4
55	BEARING, Roller, Foward Gear	31-21739
56	FOLLOWER, Cam	38441
57	SLIDE, Cross Pin	20843
58	SPRING, Retaining - Cross Pin	24-38114
59	RATCHET, Sliding Clutch	52-92911T
60	PIN, Cross, Ratchet to Propeller Shaft	17-8M0020942	17-38113
61	SPRING, Compression - Cam Follower	24-39845
62	PROPELLER SHAFT	44-75365
63	GEAR, Reverse	43-79158T
64	WASHER, Thrust - Reverse Gear	12-32004
65	BEARING, Ball, Reverse Gear	30-20839T
66	O-RING, Bearing Carrier	25-31986
67	CARRIER ASSEMBLY, Bearing	69386T1
68	BEARING, Needle, Bearing Carrier	31-21700
69	SEAL, Oil, Bearing Carrier	26-8M0205511
70	SEAL, Oil, Bearing Carrier	26-8M0203757
71	KEY, Locating - Bearing Carrier	28-30281
72	TAB WASHER, Gear Housing Cover	14-53012
73	NUT, Gear Housing	11-87763
74	TRIM TAB ASSEMBLY, Gear Housing	97-31640Q4
75	SCREW, (.437-14 x 1.75), Trim Tab to Gear Housing	10-66024
76	WASHER, (.406 x .750 x .104), Driveshaft Housing Stud (0.375 Inch)	12-8M0214963
77	NUT, (.375-24), Driveshaft Housing Stud	11-8M0204726
78	WASHER, Housing to Stud (0.437 Inch)	12-65791
79	NUT, (.437-20) Stainless Steel, Stud	11-8M0204653
80	THRUST HUB, Front	73345A1
81	TAB WASHER, Propeller Nut	14-8M0214942
82	PROP NUT KIT	11-69578Q1
-	SEAL KIT	26-79831A1
-	GASKET SET	27-85491A90

Hydraulic Pump Assembly(Electric Handle)

Below is the parts list for Mercury 45 (4 CYL.) Hydraulic Pump Assembly(Electric Handle):

Position No.	Part Name	OEM Number
-	PUMP ASSEMBLY, Hydraulic	92975A32
1	O-RING, (.364. x .070), Hydraulic Pump	25-48171
2	VALVE BODY AND GEAR ASSEMBLY	92975A32
3	SCREW, (#10-16 x .750), Valve Body to Reservoir	10-69570
4	SEAL, Reservoir to Valve Body and Gear	392-7735
5	RESEROVIR ASSEMBLY, Plastic	392-7731
6	WASHER, Thrust - Armature	392-7732
7	ARMATURE, Field and Frame	392-7729
8	FIELD AND FRAME ASSEMBLY	392-8261
9	BALL, Commutator End Plate	392-7730
10	PLATE ASSEMBLY, Commutator End	392-8262
11	BRUSH KIT, Commutator End Plate	392-8989
12	SPRING SET, Brush Tension	392-2529
13	BOLT SET, Through - Plate and Frame to Reservoir	392-7733
14	COUPLER AND SHAFT	392-7727
15	FILL PLUG, Reservoir	392-7728

Miscellaneous Parts/Accessories

Below is the parts list for Mercury 45 (4 CYL.) Miscellaneous Parts/Accessories:

Position No.	Part Name	OEM Number
--	PARTS MANUAL, 45 Hp	90-16403
-	GASKET SET	27-85491A90
--	DECAL SET, Black Small Lettering	37-13482A89
--	DECAL SET, Black Large Lettering	37-13482A89
--	OWNERS GUIDE, Black	90-44562890
--	DECAL SET, Gray	37-11621A87
--	OWNERS GUIDE, Gray	90-44564890

Mounting Hardware(Electric Handle)

Below is the parts list for Mercury 45 (4 CYL.) Mounting Hardware(Electric Handle):

Position No.	Part Name	OEM Number	Supersedes
1	SCREW, (.500-20 x 3.250), Bracket to Shock Pin Comment: (3.25 Inch)	10-62882
2	SPACER, Mounting Bracket Screw Comment: (0.50 Inch I.D.)	23-62885
2	SPACER, Mounting Bracket Screw Comment: (0.333 Inch I.D.)	23-89952
3	SPACER, Mounting Bracket Screw Comment: (0.75 Inch I.D.)	23-62884
4	PIN, Trim Cylinders to Swivel Bracket	17-62887
5	WASHER, (1.50 x .766 x .125), Trim Cylinder Pin Comment: (0.75 Inch I.D.)	12-8M0204695
6	WASHER, (.530 x .870 x .105) Stainless Steel, Trim Cylinder Pin Comment: (0.50 Inch I.D.)	12-8M0204665
7	NUT, (.500-20), Trim Cylinder Pin	11-826709117	11-35778
8	PIN, Upper Shock Mounting	55-28416
9	WASHER, (.766 x 1.312 x .125), Shock Pin	12-34937

Power Trim Components

Below is the parts list for Mercury 45 (4 CYL.) Power Trim Components:

Position No.	Part Name	OEM Number	Supersedes
1	MANIFOLD ASSEMBLY Comment: (Black)	99659A21
1	MANIFOLD ASSEMBLY Comment: (Gray)	99659A22
2	PIPE PLUG, Manifold	22-56800
3	TRIM CYLINDER ASSEMBLY Comment: (Black)	41493A9
3	TRIM CYLINDER ASSEMBLY Comment: (Gray)	41493A6
4	GUIDE ASSEMBLY	41492A1
5	REPAIR KIT	25-41478A1
6	CHECK VALVE KIT	41482A3
7	GUIDE ASSEMBLY, Trim Rod	1100-8M0021648	878243A 1
8	PISTON ASSEMBLY, Port	43397A7
9	TRIM FILTER ASSEMBLY	35-12184A1
10	PISTON/ROD ASSEMBLY, Power Trim, Starboard	878414T01	878414A 1
11	PIN, Groove, Trim Cylinder - Upper	17-821539	17-13794, 17-19603
12	VALVE ASSEMBLY	893929A01	813442A 2
12A	E RING	53-815949001	53-812844, 53-835104
13	SCREW, (M6 x 14), Cover	10-4000327
14	WASHER, Cover Screw	12-4002315
15	COVER, Manifold	99642
16	O-RING KIT	25-48462A4
17	PLUG ASSEMBLY	19-99609A1
18	SHAFT ASSEMBLY	99641A1
19	PIPE PLUG, Shaft	22-56800
20	SCREW, (M6 x 20), Pump and Motor	10-4008820
21	LOCKWASHER, (M6)	13-400256
22	PUMP AND MOTOR	826729A10	826729A09, 826729A08, 826729A07, 826729A 4
23	SHAFT, Upper	99625002
24	ANODE ASSEMBLY	97-818298Q1
25	SCREW, (M6 x 35), Anode	10-4000332
26	WASHER, (.281 x .500 x .060) Stainless Steel, Anode Screw	12-8M0204649
27	STRIKER PLATE, Trim Shaft	8M0045383	99630 1
28	LOCKWASHER, (.375)	13-58643
29	NUT, (.375-24)	11-46335
30	HARNESS ASSEMBLY, Control, Power Trim Comment: (3 Wire)	84-99695A1
30	HARNESS ASSEMBLY, Control, Power Trim Comment: (2 Wire)	84-17201A3
31	WIRE ASSEMBLY, Red Comment: (15.50 Inch)	84-79139A23
31	WIRE ASSEMBLY, (2.750 Inches), Red Comment: (2.75 Inch)	84-87379A14
32	SOLENOID, Starter	8M0185622
33	SCREW, (.250-20 x .500) Stainless Steel, Starter Solenoid	10-41508
34	NUT, Brass, Solnoid Terminal	8-32,11-26419
35	PIN, Groove, Trim Cylinder (Lower)	17-878267	17-44431
36	NUT, (.250-20) Brass, Solenoid Terminal	11-94330
37	INSULATOR, Starter Solenoid	85-97861
38	CLIP, Pump Wire	54-22875
39	C WASHER, Clip Screw	8M0084613	69205
40	SCREW, (#10-16 x .440), Clip to Transom Bracket	10-69079
41	SCREW, (M10 x 30), Manifold	10-4000377
42	LOCKWASHER, (M10) Stainless Steel, Manifold Screw	13-400258

Power Trim Components(Electric Handle)

Below is the parts list for Mercury 45 (4 CYL.) Power Trim Components(Electric Handle):

Position No.	Part Name	OEM Number	Supersedes
1	PUMP ASSEMBLY, Hydraulic	92975A32
2	O-RING, (.364. x .070), Manifold Plate	25-48171
3	SCREW, (.375-16 x .250), Filler - Hydraulic Pump	10-79953Q04
4	WASHER, Fiber, Sealing Filler Screw	12-191833
5	SCREW, (#10-32 x .437), Vent - Hydraulic Pump Hydraulic Pump	10-62269
6	PLATE, Manifold	45336
7	VALVE ASSEMBLY, Control	45197A2
--	O-RING, (.364. x .070), Manifold Plate (See Reference. #2)	25-48171
8	O-RING, Control Valve Comment: (0.75 Inch O.D.)	25-45254
9	O-RING, (.364. x .070), Control Valve Comment: (0.50 Inch O.D.)	25-48171
10	O-RING, Control Valve Comment: (0.625 Inch O.D.)	25-45253
11	SCREW, (.250-28 x 1.250), Valve and Manifold Plate to Pump Comment: (1.25 Inch)	10-56500
12	PLUG, Control Valve Comment: (0.50-20 Inch)	22-46008
13	HARNESS ASSEMBLY	84-79147A3
14	FUSE, 20 Ampere	88-8M0207796
15	CABLE ASSEMBLY, Fuse	84-95084A3
16	BRACKET, Mounting	45377T
17	SCREW, (.312-18 x 1.00), Mounting Bracket to Hydraulic Pump	10-35386
18	FUSE ASSEMBLY, 90 Ampere	88-79023T90
19	NUT, (.312-18) Cad Plated, Mounting Bracket Screw	11-21908
20	BOLT, (.375-24 x 1.75), Hydaulic Pump to Boat	10-31830
21	NUT, Hydaulic Pump Book	11-46335
22	BRACKET, Mounting - Starter Solendied	94279
23	SCREW, (.250-14 x .625), Mounting Bracket to Hydraulic Pump	10-48060
24	NUT, , Mounting Bracket to Hydraulic Pump through Bolt	10-32,11-8M0204718
25	SOLENOID, Starter	8M0185622
26	WASHER, Phenolic (.27 x .81 x .062), Fuse Terminal	12-96457
27	NUT, Brass, Solenoid Terminal	8-32,11-26419
28	LOCKWASHER, (.250) Stainless Steel, Solenoid Terminal	13-26992
29	NUT, (.250-20) Brass, Solenoid Terminal	11-94330
30	BOOT, Rubber Starter Solenoid Terminal	85-861680	85-96535
31	SCREW, (.250-20 x .500) Stainless Steel, Starter Solenoid to Mounting Bracket	10-41508
32	LINK, Soleniod to Solenoid	94275
33	CABLE ASSEMBLY, Battery Comment: (Positive)	84-79139A13
34	NUT, (.250-28), Fuse Terminal	11-21825

Power Trim Cylinder Repair Kits(Electric Handle)

Below is the parts list for Mercury 45 (4 CYL.) Power Trim Cylinder Repair Kits(Electric Handle):

Position No.	Part Name	OEM Number
-	REPAIR KIT	92188A2
1	Not Sold Separate (#N.S.S.)
2	Not Sold Separate (1-1/4" X X1-1/2" X 1/8") (#N.S.S.)
3	Not Sold Separate (#N.S.S.)
4	Not Sold Separate (1-7/8 X 2-1/16 X 3/32) (#N.S.S.)
5	Not Sold Separate (3/4 X 15/16 X 3/32) (#N.S.S.)
6	Not Sold Separate (1-1/2 X 1-3/4 X 3/32) (#N.S.S.)

Power Trim Pump(Eaton Rectangular Motor)

Below is the parts list for Mercury 45 (4 CYL.) Power Trim Pump(Eaton Rectangular Motor):

Position No.	Part Name	OEM Number	Supersedes
-	PUMP AND MOTOR	826729A10	826729A09, 826729A08, 826729A07, 826729A 4
1	FRAME AND FIELD KIT	12659
2	SPRING KIT, Brush	12665
3	BRUSH CARD KIT	13506
4	PUMP AND END FRAME KIT	12662
5	SEAL KIT, Pump	126631
6	END FRAME KIT	12660
7	ARMATURE KIT	12661
8	THRU BOLT KIT	12664

Starter Motor Assembly

Below is the parts list for Mercury 45 (4 CYL.) Starter Motor Assembly:

Position No.	Part Name	OEM Number	Supersedes
-	STARTER MOTOR ASSEMBLY	50-898265005	50-73521T
1	DRIVE KIT	90643
2	DRIVE ASSEMBLY	685753
3	PLATE, Drive End	75660
4	BOLT, Through	10-75379
6	ARMATURE	75382
7	BRUSH/SPRING KIT	898265016	75384, 75384 1
8	BUSHING, Insulating	23-57387
9	WASHER, Input Stud	12-38013
10	LOCKWASHER, (.250) Stainless Steel, Input Stud	13-26992
11	NUT, (.250-20), Input Stud	11-20890
12	HOLDER, Brush	898265014	61787
13	SCREW, Brush and Holder	10-68586
14	END CAP, Commutator	75383

Starter Rewind

Below is the parts list for Mercury 45 (4 CYL.) Starter Rewind:

Position No.	Part Name	OEM Number
1	NUT, Sheave Shaft (Left Hand Thread)	11-20166
2	TAB WASHER, Sheave Shaft Nut	14-61004
3	HOUSING, Starter	890162
4	SHEAVE ASSEMBLY, Starter	50-44255A1
5	PAWL, Starter	44508
6	SCREW, (.312-18 x 1.00), Starter Housing	10-54523
7	LOCKWASHER, Starter Housing Screw	13-20202
8	PLATE, Cable Guide	37691
9	SCREW, (#6-32 x .250), Drive - Cable Guide Plate	10-358811
10	PLATE, Starter Rewind	61002
11	SPRING	24-39502T02
12	BUSHING, Spring Guide	23-87649
13	SPRING, Starter Pawl	24-87651
14	E RING, Starter Pawl	53-87706
15	SPACER, Sheave Shaft	23-63061
17	LEVER	94962
18	WAVE WASHER	13-20160
19	SHEAVE SHAFT	87656
20	ROPE	50-12066Q10
20	ROPE AND HANDLE KIT, Manual/Emergency Start, For Manual Starting	47341A11
21	HANDLE ASSEMBLY	85174A1
22	CABLE, Interlock Comment: (Also Used on Electric Tiller Handle Models)	76568
23	SCREW, (#10-32 x .500) Stainless Steel, Interlock Cable Attaching Comment: (Also Used on Electric Tiller Handle Models)	10-69022
24	WASHER, Interlock Cable Screw Comment: (Also Used on Electric Tiller Handle Models)	12-73288
25	CAM, Interlock	428201
26	SCREW, (.312-18 x 1.120), Interlock Cam (1.125 Inch)	10-76138
27	SPRING, Interlock Cam Screw	24-761401
28	ACTUATOR, Interlock	79371
29	SCREW, Interlock Actuator (1.625 Inch)	10-76137
30	SPRING, Interlock Actuator Screw	24-76139
31	COTTER PIN, Interlock Cable to Actuator	18-26811
32	WASHER, Starter Rewind	12-35559
-	STARTER ASSEMBLY, Rewind	89016A3

Steering Handle Assembly

Below is the parts list for Mercury 45 (4 CYL.) Steering Handle Assembly:

Position No.	Part Name	OEM Number	Supersedes
1	CAP, Steering Handle Grip	48416
2	NUT, (.250-28), Steering Handle Arm	11-826709109	11-33825, 11-35045
3	WASHER, (.255 x .625 x .0312), Steering Handle Arm	12-69056
4	GRIP, Steering Handle Arm	58192A1
5	HOUSING, Drive Wheel	48414
6	DRIVE WHEEL/ROD ASSEMBLY	48516A1
7	ARM ASSEMBLY	48405A2
8	PLATE, Cover - Drive Wheel	48519
9	GASKET, Cover Plate	27-48518
10	SCREW, (#10-24 x .50), Drive Wheel Cover Plate	10-72169
11	CONDUIT, Cable	785511
12	CABLE, Throttle	48520
13	CONNECTOR, Control Linkage	89613
14	SCREW, Set - Throttle Cable Guide Tube	10-824081	10-89601
15	GUIDE TUBE, Throttle Cable Guide	8M0026078	89566 1
16	GUIDE, Throttle Cable	8M0204660
17	ANCHOR, Throttle Cable	20007
18	SET SCREW, , Throttle Cable Anchor	8-32,10-8M0204644
19	BRACKET, Handle	48404T8
20	CAP, Handle Bracket	48416
21	SCREW, Handle Bracket	10-823597	10-48476
22	WASHER, Handle Bracket Comment: (.505 I.D.)	12-48477
23	WASHER, Nylon - Handle Bracket Comment: (.630 I.D.)	12-48526
24	BUSHING, Nylon - Handle Bracket Comment: (0.625 Inch I.D.)	23-28919
25	SPACER, Handle Bracket	23-48525
26	WASHER, Nylon - Handle Bracket Comment: (1.078 Inch O.D.)	12-38000
27	WAVE WASHER, Handle Bracket	13-48478
28	WASHER, Nylon - Handle Bracket Comment: (1.75 Inch O.D.)	12-49636
29	NUT, (.500-20), Handle Bracket Screw	11-82671317
30	SCREW, (.375-24 x 1.00), Bracket to Engine	10-35786
31	TAB WASHER, Bracket Screw	14-43589
32	DETENT, Shift Lever	78812A1
33	SCREW, (#10-16 x .625) Stainless Steel, Shift Lever Detent	10-48409
34	SHIFT LEVVER	485681
35	BUSHING, Nylong - Shift Lever Comment: (0.375 Inch I.D.)	23-48237
36	WASHER, (.406 x .734 x .063) Stainless Steel, Shift Lever	12-34931
37	NUT, (.375-24), Shift Lever	11-8M0204726
38	SHIFT ROD	8128061
39	ROD END, Shift Rod	48419T
40	BUSHING, Nylon - Shift Rod Comment: (0.25 Inch I.D.)	23-48475
41	WASHER, (.273 x .437 x .031) Stainless Steel, Shift Rod	12-35950
42	COTTER PIN, Shift Rod	18-25191
43	KNOB, Shift Lever	98530
44	SWITCH ASSEMBLY, Stop	87-11083A11
45	RETANER, Stop Switch	8M0032846	12044 1
46	LANYARD ASSEMBLY	15920Q54
47	CLAMP, Stop Switch	54-648552
--	CO-PILOT KIT	52148A1

Swivel Bracket and Reverse Lock(Non Power Trim)

Below is the parts list for Mercury 45 (4 CYL.) Swivel Bracket and Reverse Lock(Non Power Trim):

Position No.	Part Name	OEM Number	Supersedes
1	SWIVEL BRACKET Comment: (Short Shaft)	1489-8597A4
1	SWIVEL BRACKET Comment: (Long Shaft)	1490-8599A6
2	SEAL, Oil, Swivel Bracket	26-32911
3	FITTING, Grease	22-8M0169589
4	SEAL, Oil, Swivel Bracket	26-22734
5	SWIVEL PIN ASSEMBLY, Two Piece Steering Arm Comment: (Short Shaft)	88798A23
5	SWIVEL PIN ASSEMBLY, Two Piece Steering Arm Comment: (Long Shaft)	88798A24
5	SWIVEL PIN ASSEMBLY, One Piece Steering Arm Comment: (Short Shaft)	69540A3
5	SWIVEL PIN ASSEMBLY, One Piece Steering Arm Comment: (Long Shaft)	69540A4
6	BUMPER, Steering Arm	30711
7	BOLT, (.437-20 x 5.250), Upper MOunt to Swivel Pin (5.25 Inch)	10-66897
8	WASHER, Swivel Pin - Lower	12-47606
9	BRACKET, Ride - Guide Comment: (Manual/Electric without Tiller Handle)	76535T
10	SCREW, (.375-24 x .875), Bracket Comment: (Manual/Electric without Tiller Handle)	10-34352
11	STRAP, Bracket Screw Comment: (Manual/Electric without Tiller Handle)	76533
12	WASHER, Swivel Pin to Bottom Yoke (.060)	12-25176
13	YOKE, Bottom Comment: (Black)	77416T1
13	YOKE, Bottom Comment: (Gray)	77416T6
14	RETAINING RING, Bottom Yoke	53-77415
15/16	TILT LOCK Comment: (Starboard/Port)	89105
15/16	TILT LOCK Comment: (Handle Models)	99431A1
17	O-RING, (.301 x .070), Tilt Lock	25-627021
18	COUPLING, Tilt Lock	79659
19	COTTER PIN, Tilt Lock Tube	18-47959
20	SHAFT, Reverse Lock Pivot	56349
21	BUSHING, Reverse Pivot Shaft	23-69132
22	COTTER PIN, Reverse Lock to Shaft	18-45882
23	SPRING, Reverse Lock Tension	24-78203A2
24	REVERESE LOCK	14664A3
25	PUSH ROD, Reverse Lock Comment: (Short Shaft)	43415
25	PUSH ROD, Reverse Lock Comment: (Long Shaft)	43416
26	WASHER, (.323 x .563 x .063) Stainless Steel, Push Rod	12-8M0042642	12-70132
27	SPRING, Push Rod	24-44297
28	ROD END, Push Rod	89813
29	NUT, (.312-24) Stainless Steel, Push Rod	11-82670911
30	GUIDE, Push Rod	933361
-	GASKET SET	27-85491A90

Swivel Bracket and Steering Arm

Below is the parts list for Mercury 45 (4 CYL.) Swivel Bracket and Steering Arm:

Position No.	Part Name	OEM Number	Supersedes
1	SWIVEL BRACKET ASSEMBLY Comment: (Black)	1499-8M0102865	1499-8710T20 (Black)
1	SWIVEL BRACKET ASSEMBLY Comment: (Gray)	1499-8710T21
2	SEAL, Oil, Swivel Bracket (Lower)	26-87735
3	BUSHING, Swivel Bracket (Lower and Upper)	23-818764	23-67669
4	O-RING, Swivel Bracket (Upper)	25-33466
5	SPACER, Swivel Bracket (Upper)	23-67668
6	FITTING, Grease, Grease	22-8M0169589
7	BUSHING, Swivel Bracket	23-821207	23-99608
8	SCREW, (.250-28 x .500), Swivel Bracket	10-64014
9	SCREW, (.437-20 x 6.620), Steering Arm to Upper Mount	10-99621
10	BUMPER, Top Yoke	28203
11	WAVE WASHER, Bottom Yoke	13-78854
12	YOKE, Bottom Comment: (Black)	42961T
12	YOKE, Bottom Comment: (Gray)	42961T6
13	RING, Retaining, Bottom Yoke	53-67684
14	WASHER, Thrust - Swivel Bracket	12-67670
15	SWIVEL PIN ASSEMBLY	99661A2
16	LINK ASSEMBLY, Steering	92876A12
17	SCREW, (.375-24 x 1.25), Steering Link to Steering Arm	10-849838	10-14000
18	NUT, (.375-24), Steering Link Screw	11-8M0204726
19	WASHER, (.406 x .734 x .063) Stainless Steel, Steering Link to Steering Arm	12-34931
-	GASKET SET	27-85491A90

Throttle Control Linkage

Below is the parts list for Mercury 45 (4 CYL.) Throttle Control Linkage:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET, Throttle Actuator	72040T
2	SCREW, (.312-18 x 1.125), Throttle Actuator Bracket Comment: (1.125 Inch)	10-53576
3	LOCKWASHER, (.312), Throttle Actuator Bracket Screw	13-8M0204647
4	ACTUATOR, Throttle	815603A1
5	SCREW, (.312-24 x 2.00), Bracket to Throttle Actuator	10-21449
6	WASHER, Bracket Screw	12-25893
7	WAVE WASHER, Bracket Screw	13-62172
8	NUT, (.312-24), Bracket Screw	11-29250
9	SWIVEL, Link Rod to Throttle Actuator	57440
10	LINK ROD	72043
11	SWIVEL, Link Rod to Throttle Arm	57440
12	ARM, Throttle	76560
13	SCREW, Adjusting - Throttle Arm Comment: (2.25 Inch)	10-89778
13	SCREW, (.190-32 x 1.75), Adjusting - Throttle Arm	10-25158
14	NUT, Stainless Steel, Adjusting Screw	10-32,11-68219
15	CAP, Adjusting Screw	48039
16	LATCH, Throttle Arm	39483
17	SCREW, (.250-28 x .880), Latch to Throttle Arm	10-69026
18	SPRING, Compression - Latch Screw	24-20099
19	NUT, (.250-28), Latch Screw	11-826709109	11-33825, 11-35045
20	LEVER, Spark Advance	815607A1
21	SCREW, (.375-16 x 1.75), Lever and Arm to Cylinder Block Comment: (1.75 Inch)	10-818165	10-55337 (1.75 Inch)
22	BUSHING, Lever and Arm Screw	23-55164
23	BUSHING, Lever and Arm Screw	23-55171
24	SPRING, Return - Spark Advance Lever	24-55162
25	WASHER, Lever and Arm Screw	12-68410
26	SCREW, (.190-32 x 1.75), Adjusting - Spark Advance Lever	10-25158
27	NUT, Stainless Steel, Adjusting Screw	10-32,11-68219
28	CAP, Adjusting Screw	48039
29	LINK ROD, Spark Advance Comment: (2.50 Inch Long)	76056
30	PIVOT, Threaded - Link Rod to Trigger	74897T
31	SWIVEL, Link Rod to Spark Advance Lever	77013A1
32	WAVE WASHER, Swivel	13-29402
33	BUSHING, Link Rod Swivel	23-26856
34	WASHER, Link Rod Swivel	12-73288
35	NUT, Link Rod Swivel	11-45774
36	PLATE, Throttle Actuator	66778T
37	SCREW, (#10-24 x .500), Plate to Throttle Actuator Comment: (.50 Inch Length)	10-46420
38	SCREW, (.190-32 x 1.00), Adjusting - Plate	10-23015
39	NUT, Stainless Steel, Adjusting Screw	10-32,11-68219
40	CAP, Adjusting Screw	48039

Transom Bracket(Power Trim)

Below is the parts list for Mercury 45 (4 CYL.) Transom Bracket(Power Trim):

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET ASSEMBLY, Transom, Starboard - Black	3401-8718F7
2	BRACKET ASSEMBLY, Transom, Port - Black	3400-8716A8
1	BRACKET ASSEMBLY, Transom, Starboard - Gray	3401-8718F8
2	BRACKET ASSEMBLY, Transom, Port - Gray	3400-8716A9
3	FITTING, Grease, Port Tramsom Bracket	22-8M0169588
4	TILT TUBE	99170A2
5	NUT, Tilt Tube Comment: (Black)	11-859133	11-34862, 11-90068F 3, 11-90068F 4 (Black)
5	NUT, Tilt Tube Comment: (Gray)	11-859133	11-34862, 11-90068F 3, 11-90068F 4 (Gray)
6	O-RING, (.612 x .103), Tilt Tube	25-45711
7	WASHER, Tilt Tube	13-88750
8	NUT, (.875-14), Tilt Tube (7.57)	11-858869	11-30499
9	SCREW, (.500-20 x 4.500), Mounting Bracket to Tramsom	10-8M0149747
10	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel, Mounting Bracket Bolt	12-8M0204648
11	NUT, (.500-20), Mounting Bracket Bolt	11-91962
12	BOLT ASSEMBLY, Tilt Lock	10-96930A1
13	NUT, (.375-24), Bolt	11-23161
14	LEVER ASSEMBLY, Tilt Lock	8M0115104	8M0115103, 99629T 2
15	WAVE WASHER, Tilt Lever	13-99611
16	NYLINER, Tilt Lever	23-65830
17	KNOB, Tilt Lock Lever Comment: (Black)	99633
17	KNOB, Tilt Lock Lever Comment: (Gray)	99633
18	PIN, Groove	17-99615
19	SPRING	24-99622
20	PIN, Groove	17-99604
21	NUT, (.875-14)	11-8M0041651	11-37984

Trim Cylinders and Hoses(Electric Handle)

Below is the parts list for Mercury 45 (4 CYL.) Trim Cylinders and Hoses(Electric Handle):

Position No.	Part Name	OEM Number	Supersedes
1	TRIM CYLINDER Comment: (Black)	92194A14
1	TRIM CYLINDER Comment: (Gray)	92194A20
2	FITTING, Grease, Trim Cylinder	22-8M0169589
3	SCREW, (#10-32 x .3125), Bleed	10-45265
4	O-RING, Bleed Screw	25-45016
5	SCREW, (.500-20 x 1.500), Trim Cylinder Comment: (1.50 Inch)	10-92050
6	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel, Trim Cylinder Bolt	12-8M0204648
7	SPACER, Trim Cylinder - Lower	23-45280
8	BUSHING, Rubber - Trim Cylinder	23-94907A1
9	BRACKET, Trim Cylinder Comment: (Port)	89108A3
10	SEAL, Oil, Port Bracket	26-70608
11	PLUNGER, Limit Switch Actuating	89290
12	SPRING, Tension - Limit Switch Plunger	24-95881
13	STUD, (.312-24 x 16.620), Mounting Bracket	16-45282
14	LOCKWASHER, (.312), Mounting Bracket Stud	13-8M0204647
15	NUT, (.312-24) Stainless Steel, Mounting Bracket Stud	11-28770
17	BOLT, (.375-16 x 3.250), Mounting Bracket to Transom Comment: (3.25 Inch)	10-68298
17	SCREW, (.375-16 x 5.00), Mounting Bracket to Transom Comment: (5.00 Inch)	10-89673
18	WASHER, Mounting Bracket Bolt	12-68410
19	NUT, Mounting Bracket Bolt	11-82671112
20	BRACKET, Trim Cylinder Comment: (Starboard)	89111T
21	SCREW, (.437-20 x 3.560), Trim Cylinder to Mounting Bracket Comment: (3.563 Inch)	10-45328
22	WASHER, Trim Cylinder Screw Comment: (Starboard Only)	12-37807
23	NUT, (.437-20), Trim Cylinder Screw	11-8M0143423
24	SPRING, Tension - Adjusting Stud	24-24390
25	STUD, (#10-32 x .930), Adjusting - Cut - Out Limit Switch	16-8M0034461	16-21085
26	NUT, Stainless Steel, Jam - Limit Switch Adjusting Stud	10-32,11-859124	11-45812
27	CAM, Limit Switch Adjusting Stud	99897
28	PLATE, Retaining - Limit Switch Cam	86967
29	SCREW, (#10-32 x .375) Stainless Steel, Retaining Plate and Cam	10-68513
30	LOCKWASHER, Stainless Steel, Retaining Plate and Cam Screw	10,13-26996
31	SWITCH ASSEMBLY, Cut - Out Limit	45326A2
32	BUSHING, Rubber - Cut- Out Limit Switch	23-45354
33	SCREW, (#4-40 x .625), Cut - Out Limit Switch Comment: (0.563 Inch)	10-47255
34	COVER, Limit Switch	89272
35	GASKET, Limit Switch Cover	27-892731
36	SCREW, (#10-32 x 1.00) Stainless Steel, Limit Switch Cover Comment: (0.438 Inch)	10-34994
37	WASHER, Limit Switch Cover Screw	12-38833
38	COVER, Inlet - Transom	87774A1
39	GASKET, Inlet Cover	27-87775
40	GROMMET, Rubber - Inlet Cover	25-45507
41	SCREW, (#10-32 x 1.250), Inlet Cover to Boat	10-36070
42	LOCKWASHER, Stainless Steel, Inlet Cover Screw	10,13-26996
43	NUT, Stainless Steel, Inlet Cover Screw	10-32,11-68219
44	HOSE, Trim - Cylinder to Control Valve Comment: (5.375 Feet O.D.)	32-88005
45	HOSE, Lift - Cylinder to Control Valve Comment: (5.321 Feet O.D.)	32-88006
46	GROMMET, Rubber Comment: (0.375 Inch I.D. - 1 Inch Long)	23-35977
46	GROMMET, Rubber Comment: (0.375 Inch I.D. - 0.875 Inch Long)	23-35977
46	GROMMET, Rubber Comment: (0.375 Inch I.D. - 0.875 Inch Long)	25-12602002
47	STRAP	98876
48	SPRING	24-98875
49	PIN, Mounting Tube	98878
50	TUBE, Cushion	63473
51	COTTER PIN, Mounting Tub Pin	18-8M0214922
52	COTTER PIN, Tilt Pin Retaining	18-45882
54	SPACER, Mounting Bracket	23-59623

Download this page as PDF: Click here

For Mercury Owners:

To assist you in maintaining and repairing your marine engines, we hope the following resources may be of use:

Mercury / Mercruiser / Mariner Parts from JLM Marine

About JLM Marine

Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.

As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.

We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.