Mercury 35 (2 CYL.) (9384476 & Up) Outboard Motor Parts Diagram & Catalog – Free PDF Download

by JLM Marine 30 Apr 2025 0 Comments

Mercury 35 (2 CYL.) Outboard Motor Parts Diagram & Catalog – Free PDF Download

AUTO-BLEND

Below is the parts list for Mercury 35 (2 CYL.) AUTO-BLEND:

Position No.	Part Name	OEM Number
-	AUTO-BLEND	1301931
1	TANK KIT, Oil	16612
2	HANDLE KIT	13996
3	CAP, OIL TANK	36-13986
4	HARDWARE KIT	16614
5	PLUG KIT, Drain	19-13979
6	DIAPHRAGM KIT	16611
7	BRACKET	13990
8	BAND	13993
9	BRACKET (LEFT)	13983
10	BRACKET (RIGHT)	13984
11	COVER	16613
12	FILTER/SENSOR KIT, Oil	35-13985
13	HORN KIT	13987
14	HARNESS ASSEMBLY	84-13988
15	FUSE (.5 AMP)	88-13989
16	FILTER KIT, Fuel	35-18089
17	VINYL TUBE	32-13992
18	TUBE KIT, Fuel	32-13995
19	STRAINER ASSEMBLY, Oil	15387A1
20	CHECK VALVE KIT	21-16615
21	GASKET KIT	27-16616

BOTTOM COWL AND EXHAUST PLATE

Below is the parts list for Mercury 35 (2 CYL.) BOTTOM COWL AND EXHAUST PLATE:

Position No.	Part Name	OEM Number
1	BOTTOM COWL ASSEMBLY	2139-7642A2
2	COVER, PLUG - BOTTOM COWL HARNESS HOLE Comment: MANUAL	57786
3	SCREW, PLUG COVER TO BOTTOM COWL (7/8") Comment: MANUAL	10-61802
4	PLUG, BOTTOM COWL Comment: MANUAL	88618
5	SCREW, (#10-16 x .625) Stainless Steel, PLUG TO BOTTOM COWL Comment: MANUAL	10-48409
6	WASHER, (.203 x .500 x .032), PLUG SCREW Comment: MANUAL	12-8M0204666
7	GASKET, POWERHEAD TO EXHAUST EXTENSION PLATE	27-628601
8	SEAL, RUBBER - EXHAUST PLATE TO BOTTOM COWL	39622
9	PLATE ASSEMBLY, EXHAUST EXTENSION	42818A1
10	BUSHING, FLANGE EXHAUST PLATE	23-71980
11	WASHER, NYLON - WATER OUTLET TUBE	12-38453
12	SEAL, RUBBER - WATER OUTLET TUBE	26-38452
13	HOUSING, WATER INLET TUBE SEAL	79799
14	GASKET, HOUSING	27-797971
15	SCREW, (#10-32 x 1.380), HOUSING TO EXHAUST PLATE	10-79798
16	GASKET, EXHAUST PLATE	27-385011
17	BOOT, FUEL CONNECTOR - BOTTOM COWL	37637
18	BOOT, CONTROL CABLE - BOTTOM COWL	39616
19	COVER PLATE	39555
20	SCREW, (#10-24 x .375), COVER PLATE TO BOTTOM COWL	10-8M0113176
21	LEVER, FRONT COVER	76176
22	SPRING, FRONT COVER LEVER	24-76177
23	PIN, Roll, LEVER TO BOTTOM COWL	17-26541
24	KNOB AND SHAFT, CHOKE	47969
25	WASHER, CHOKE SHAFT	12-30314
26	SPRING, COMPRESSION - CHOKE SHAFT	24-47968
27	LEVER, CHOKE	55180
28	SWITCH ASSEMBLY, Stop Comment: MANUAL PUSH BUTTON SWITCH	87-69508A9
29	COVER ASSEMBLY, STOP SWITCH Comment: MANUAL PUSH BUTTON SWITCH	87-99525A1
30	NUT, STOP SWITCH Comment: MANUAL PUSH BUTTON SWITCH	11-69844
31	CABLE ASSEMBLY, BOTTOM COWL	84-88238T01
32	SCREW, (#10-24 x .375), GROUND STRAP	10-8M0113176
33	BRACKET, SUPPORT - TOP COWL (REAR)	76132
34	MOUNT, RUBBER - REAR SUPPORT BRACKET	60577
35	WASHER, (.255 x .625 x .0312), RUBBER MOUNT	12-69056
36	LOCKWASHER, (.250) Stainless Steel, RUBBER MOUNT	13-26992
37	NUT, RUBBER MOUNT	11-36069
38	MOUNT, RUBBER - REAR SUPPORT BRACKET	90435
39	NUT, RUBBER MOUNT	11-36069
40	SCREW, (.312-18 x 1.00) Stainless Steel	10-37562
41	LOCKWASHER, (.312)	13-8M0204647
42	BRACKET, SUPPORT - TOP COWL (FRONT)	95967T
43	MOUNT, RUBBER - FRONT SUPPORT BRACKET	31014
44	WASHER, (.255 x .625 x .0312), RUBBER MOUNT	12-69056
45	LOCKWASHER, (.250) Stainless Steel, RUBBER MOUNT	13-26992
46	NUT, RUBBER MOUNT	11-36069
47	SCREW, (.312-18 x 1.00) Stainless Steel	10-37562
48	LOCKWASHER, (.312)	13-8M0204647
49	MOUNT, RUBBER - FRONT SUPPORT BRACKET	90435
50	NUT, (1/4-28X7/32), RUBBER MOUNT	11-8M0207775
-	GASKET SET	27-78028A78

CARBURETOR ASSEMBLY

Below is the parts list for Mercury 35 (2 CYL.) CARBURETOR ASSEMBLY:

Position No.	Part Name	OEM Number	Supersedes
1	CARBURETOR ASSEMBLY	1368-7226A19
2	FLOAT ASSEMBLY	1395-8673
3	NOT SOLD SEPARATE, FLOAT PIN	NSS
4	NOT SOLD SEPARATE, FLOAT LEVER (LOWER)	NSS
5	NOT SOLD SEPARATE, FLOAT LEVER (UPPER)	NSS
6	NEEDLE, Inlet	1395-83181
7	NOT SOLD SEPARATE, GASKET-INLET NEEDLE	NSS
8	NOT SOLD SEPARATE, GASKET-FLOAT BOWL COVER	NSS
9	COVER, FLOAT BOWL	1395-9016
10	JET, Main (.092)	1395-5733
11	HOSE, ECONOMIZER	1395-5734
12	SCREW, FLOAT BOWL COVER	10-52195
13	SCREW, FLOAT BOWL COVER	1395-4804
14	LOCKWASHER, Stainless Steel, FLOAT BOWL COVER SCREW	8,13-26995
15	LEVER, THROTTLE	92880
16	SCREW, (#5-40 x .500), THROTTLE LEVER	10-60293
17	PUSH NUT, THROTTLE LEVER SCREW	11-92500
18	SHAFT, Throttle	1395-8641
19	NOT SOLD SEPARATE, IDLE TUBE	NSS
20	SCREW, BODY (IDLE TUBE)	1395-4540
21	SHUTTER, Throttle	1395-9017
22	NOT SOLD SEPARATE, SCREW, THROTTLE SHUTTER	NSS
23	NOT SOLD SEPARATE, SPRING-IDLE ADJUSTMENT SCREW	NSS
24	NOT SOLD SEPARATE, SCREW-IDLE ADJUSTMENT	NSS
25	NOT SOLD SEPARATE, MAIN NOZZLE	NSS
26	SCREW, PLUG - MAIN NOZZLE	1395-4542
27	JET, (.074), MAIN FUEL	1399-3794
27	JET, (.072), MAIN FUEL	1395-6207
27	JET, (.070), MAIN FUEL	1395-6030
28	SCREW, PLUG - MAIN FUEL JET CHANNEL	1395-4541
29	NOT SOLD SEPARATE, GASKET-JET CHANNEL PLUG SCREW	NSS
30	NOT SOLD SEPARATE, SPRING-THROTTLE SHAFT RETURN	NSS
31	SCREW, BODY CHANNEL	1395-4543
32	VENTURI, Plastic	52106A1
33	NOT SOLD SEPARATE, PLUG-BODY CHANNEL	NSS
-	GASKET SET	1395-879194024	1399-3523, 1395-4808, 1395-4808B 1
-	REPAIR PARTS KIT	1395-51091
34	GASKET, CARBURETOR FLANGE	27-481641
35	NUT, CARBURETOR MOUNTING STUD	11-64809
36	STUD, CHOKE SHUTTER PIVOT (CARBURETOR)	16-69016
37	SHUTTER, Choke, CARBURETOR	55179
38	SPRING, TENSION - CHOKE SHUTTER	24-55163
39	WASHER, CHOKE SHUTTER CARBURETOR STUD	12-47960
40	NUT, , CHOKE SHUTTER TO CARBURETOR STUD	10-32,11-20110
41	SCREEN, CARBURETOR	35-57819
42	SCREW, (#10-32 x 1.00), SCREEN TO CARBUETOR	10-58185
43	SPRING, TENSION - SCREEN SCREW	24-57818
44	WASHER, SCREEN SCREW	12-30164
45	NUT, , SCREEN SCREW	10-32,11-20110

CLAMP AND SWIVEL BRACKET(NON POWER TRIM)

Below is the parts list for Mercury 35 (2 CYL.) CLAMP AND SWIVEL BRACKET(NON POWER TRIM):

Position No.	Part Name	OEM Number	Supersedes
1	CLAMP BRACKET ASSEMBLY Comment: (MANUAL)	1427-5611A5
1	CLAMP BRACKET ASSEMBLY Comment: (ELECTRIC)	1427-5611A4
2	THUMB SCREW ASSEMBLY Comment: (MANUAL)	10-90470A3
2	THUMB SCREW ASSEMBLY Comment: (ELECTRIC)	10-78492A1
3	SCREW, WASHER TO THUMB SCREW	10-78495
4	WASHER, THUMB SCREW	12-78493
5	CAP, THUMB SCREW Comment: (ELECTRIC)	75043
6	PIN ASSEMBLY, Tilt Lock	17-8M0026068	17-49930A 1
7	SPACER, CLAMP BRAKCET STUD	23-59623
8	STUD, CLAMP BRACKET	16-59625
9	LOCKWASHER, (.312), STUD	13-8M0204647
10	NUT, (.312-24) Stainless Steel, STUD	11-28770
11	TILT TUBE	8M0041936	8M0035074, 883067, 30664 2, 74528
12	WASHER, CLAMP BRACKET TO SWIVEL BRACKET	12-52864
13	NUT, (.875-14), TILT TUBE	11-858869	11-30499
15	BOLT, (.375-16 x 3.250) (LOWER)	10-68298
16	WASHER, CLAMP BRACKET BOLT (LOWER)	12-68410
17	NUT, CLAMP BRACKET BOLT	11-82671112
18	SWIVEL PIN ASSEMBLY Comment: (SHORT SHAFT)(MANUAL/ELECTRIC)	88798A23
18	SWIVEL PIN ASSEMBLY Comment: (LONG SHAFT)(MANUAL/ELECTRIC)	88798A24
18A	SWIVEL PIN ASSEMBLY Comment: (SHORT SHAFT)(ELECTRIC-DESIGN I)	69540A3
18A	SWIVEL PIN ASSEMBLY Comment: (LONG SHAFT)(ELECTRIC-DESIGN I)	69540A4
19	BUMPER, STEERING ARM	30711
20	BOLT, (.437-20 x 5.250), UPPER MOUNT TO STEERING ARM	10-66897
21	BUMPER, STEERING ARM Comment: W/O TILLER HANDLE	62297
22	BRACKET, RIDE-GUIDE ATTACHING Comment: W/O TILLER HANDLE	76535T
23	SCREW, (.375-24 x .875), BRACKET TO STEERING ARM Comment: W/O TILLER HANDLE	10-34352
24	STRAP, BRACKET SCREW Comment: W/O TILLER HANDLE	76533
25	WASHER, SWIVEL PIN	12-52865
26	SWIVEL BRACKET Comment: (SHORT SHAFT)	1481-7656A1
26	SWIVEL BRACKET Comment: (LONG SHAFT)	1480-7655A1
27	SEAL, Oil, SWIVEL BRACKET	26-32911
28	FITTING, Grease, SWIVEL BRACKET	22-8M0169589
29	LEVER ASSEMBLY, TILT LOCK - PORT SIDE	47913A2
30	SCREW, (.312-24 x .880)	10-69087
31	NUT, (.312-24), TILT LOCK AND STOP LEVER SCREW	11-29250
32	LEVER ASSEMBLY, TILT STOP - STARBOARD SIDE	47912A2
33	BUSHING, TILT LOCK AND STOP LEVER	23-47911
34	WASHER, WAVE - TILT LOCK AND STOP LEVER	13-34632
35	WASHER, (.330 x .750 x .060) Stainless Steel, TILT LOCK AND STOP LEVER	12-56720
36	NUT, (.312-24)	11-29250
37	PIN, REVERSE LOCK SPRING ATTACHING	17-25598
38	SHAFT, REVERSE LOCK TO SWIVEL BRACKET	56349
39	LOCK ASSEMBLY, Reverse	14664A3
40	SPRING, REVERSE LOCK TENSION	24-29821
41	COTTER PIN, REVERSE LOCK TO SHAFT	18-45882
42	WASHER, SWIVEL PIN TO BOTTOM YOKE (.060)	12-25176
43	YOKE, Bottom	77416T1
44	RETAINING RING, BOTTOM YOKE	53-77415
45	ROD END, PUSH ROD	89813
46	ROD, PUSH - REVERSE LOCK Comment: (SHORT SHAFT)	43412
46	ROD, PUSH - REVERSE LOCK Comment: (LONG SHAFT)	43413
47	NUT, (.312-24) Stainless Steel, JAM - PUSH ROD	11-82670911
48	PIN, REVERSE LOCK LEVER	17-72524
49	COTTER PIN, PUSH ROD TO REVERSE LOCK	18-25191
50	GUIDE, PUSH ROD	933361
51	SPRING, PUSH ROD	24-44297
52	WASHER, (.323 x .563 x .063) Stainless Steel, PUSH ROD	12-8M0042642	12-70132

CLAMP AND SWIVEL BRACKET(POWER TRIM)

Below is the parts list for Mercury 35 (2 CYL.) CLAMP AND SWIVEL BRACKET(POWER TRIM):

Position No.	Part Name	OEM Number	Supersedes
1	SWIVEL BRACKET	1490-8599A6
2	SEAL, Oil, SWIVEL BRACKET	26-32911
3	FITTING, Grease	22-8M0169589
4	SEAL, Oil, SWIVEL BRACKET	26-22734
5	SWIVEL PIN ASSEMBLY (EARLY STYLE)	69540A4
6	SWIVEL PIN ASSEMBLY (LATER STYLE)	88798A24
7	BUMPER, STEERING ARM	30711
8	BOLT, (.437-20 x 5.250)	10-66897
9	WASHER (.060)	12-25176
10	YOKE, Bottom	77416T1
11	RETAINING RING, BOTTOM YOKE	53-77415
12	TILT LOCK, STARBOARD/PORT	89105
13	O-RING, (.301 x .070)	25-627021
14	COUPLING, TILT LOCK	79659
15	COTTER PIN, TILT LOCK TUBE	18-47959
16	PIN, TRIM CYLINDERS TO SWIVEL BRACKET	17-62887
17	WASHER, (1.50 x .766 x .125), TRIM CYLINDER PIN	12-8M0204695
18	WASHER, (.530 x .870 x .105) Stainless Steel, TRIM CYLINDER PIN	12-8M0204665
19	NUT, (.500-20), TRIM CYLINDER PIN	11-826709117	11-35778
20	CLAMP BRACKET ASSEMBLY	1440-8394A1
21	THUMB SCREW ASSEMBLY	10-78492A1
22	WASHER, THUMB SCREW	12-78493
23	SCREW, WASHER TO THUMB SCREW	10-78495
24	CAP, THUMB SCREW	75043
25	TILT TUBE	8M0041936	8M0035074, 883067, 30664 2, 74528
26	WASHER, TILT TUBE	12-52864
27	NUT, (.875-14), TILT TUBE	11-858869	11-30499
28	CAP, PLASTIC - TILT TUBE	53078
29	PIN, UPPER	55-28416
30	BUSHING, CLAMP BRACKET	23-73203
31	SCREW, (.500-20 x 3.250), BRACKET TO UPPER PIN	10-62882
32	SPACER, MOUNTING BRACKET SCREW Comment: (1/2"I.D)	23-62885
32	SPACER, MOUNTING BRACKET SCREW Comment: (1/3"I.D)	23-89952
33	SPACER, MOUNTING BRACKET SCREW Comment: (3/4"I.D)	23-62884
34	BOLT, (.375-16 x 3.250)	10-68298
35	WASHER, CLAMP BRACKET BOLT	12-68410
34	SCREW, (.375-16 x 5.00)	10-89673
35	WASHER, (1-1/ 4 x 25/64 x .125 SS), CLAMP BRACKET BOLT	12-28420
36	NUT, CLAMP BRACKET BOLT	11-82671112
37	BUMPER, STEERING ARM Comment: W/O TILLER HANDLE	62297
38	BRACKET, RIDE-GUIDE ATTACHING Comment: W/O TILLER HANDLE	76535T
39	SCREW, (.375-24 x .875) Comment: W/O TILLER HANDLE	10-34352
40	STRAP, BRACKET SCREW Comment: W/O TILLER HANDLE	76533
-	GASKET SET	27-78028A78

CRANKSHAFT, PISTONS AND CONNECTING RODS

Below is the parts list for Mercury 35 (2 CYL.) CRANKSHAFT, PISTONS AND CONNECTING RODS:

Position No.	Part Name	OEM Number	Supersedes
1	CRANKSHAFT ASSEMBLY	454-9073A1
2	RETAINER ASSEMBLY, BALL BEARING	78308A1
3	BEARING, Ball, RETAINER (CRANKSHAFT)	30-63742T
4	RING, Retaining, BALL BEARING	53-63634
5	BEARING ASSEMBLY, Main, VALVE TYPE	540-7238A2
6	PIN, Dowel, MAIN, BEARING	17-20032
7	SCREW, (#12-28 x .560) , MAIN BEARING CLAMPING	10-45775
8	NUT, MAIN BEARING CLAMPING SCREW	11-45774
9	REED SET, MAIN BEARING (MATCHED)	34-56007A1
10	STOP, Reed, MAIN BEARING REED VALVES	34-56008
11	SCREW, (#10-32 x .375), REED STOP MOUNTING	10-20055
12	CONNECTING ROD ASSEMBLY	624-8101A3
13	SCREW, (.250-28 Special), CONNECTING ROD	10-91012
15	BEARING ASSEMBLY, CRANKPIN	31-62596A1
16	BEARING, PISTON PIN	29-8M0214934
17	WASHER, NEEDLE BEARING RETAINING	12-8M0032839	12-47247
18	PISTON ASSEMBLY Comment: (STANDARD)	774-9137A12
18	PISTON ASSEMBLY Comment: (.015 OVERSIZE)	774-9137A13
18	PISTON ASSEMBLY Comment: (.030 OVERSIZE)	774-9137A14
19	RING Comment: (STANDARD)	39-78816A12
19	RING SET, Piston - .015 Oversize	39-78811A12
19	RING SET, Piston - .030 Oversize	39-88392A12
20	RING, Lock, PISTON PIN	53-857196	40-52035
21	KEY, CRANKSHAFT	28-45554

CYLINDER BLOCK AND THERMOSTAT

Below is the parts list for Mercury 35 (2 CYL.) CYLINDER BLOCK AND THERMOSTAT:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER BLOCK ASSEMBLY	851-7940A6
2	BRACKET, COIL MOUNTING	66843T
3	COVER ASSEMBLY, COIL BRACKET	99436A1
4	O-RING, COVER	25-823683	25-64067
5	SCREW, (.312-18 x 1.375), COIL MOUNTING BRACKET TO BLOCK	10-31984
6	SCREW AND LOCKWASHER, (.312-18 x 1.00), COVER	10-30225
7	SCREW, COVER AND COIL BRACKET TO BLOCK (2-1/2")	10-58414
8	LOCKWASHER, (.312), COIL MOUNTING BRACKET SCREW	13-8M0204647
9	GROMMET, COIL MOUNTING BRACKET	25-39597
10	GASKET, COIL MOUNTING BRACKET TO BLOCK	27-66847
11	HOSE, CYLINDER BLEED (8")	32-9938779
12	CHECK VALVE, CYLINDER BLEED (TOP)	21-42866
13	CHECK VALVE, CYLINDER BLEED (BOTTOM)	21-42863
14	SWITCH ASSEMBLY Comment: (BOLT/NUT CONNECTORS)	58124A27
14	SWITCH Comment: (BULLET CONNECTORS)	58124A27
15	SCREW, (#10-16 x .375), MERCURY SWITCH TO EXHAUST COVER	10-62568
16	INDICATOR, TIMING Comment: ELECTRIC	76184
17	SCREW, (.312-18 x .75), INDICATOR ATTACHING Comment: ELECTRIC	10-25299
18	WASHER, (.328 x .562 x .062), INDICATOR ATTACHING SCREW Comment: ELECTRIC	12-20084
19	PIN, INDICATOR LOCATING Comment: ELECTRIC	17-29908
-	GASKET SET	27-78028A78

CYLINDER BLOCK CRANKCASE AND COVERS

Below is the parts list for Mercury 35 (2 CYL.) CYLINDER BLOCK CRANKCASE AND COVERS:

Position No.	Part Name	OEM Number	Supersedes
1	END CAP ASSEMBLY, Upper	1167-8277A1
2	O-RING, UPPER END CAP	25-47254
3	BEARING, Roller, UPPER END CAP	31-62066T
4	SEAL, UPPER END CAP	26-41953
5	SCREW AND LOCKWASHER, (.312-18 x 1.00), UPPR END CAP MOUNTING	10-30225
6	CYLINDER BLOCK ASSEMBLY	851-7940A6
7	STUD, CARBURETOR MOUNTING (1-1/4")	16-64936
8	STUD, CRANKCASE TO DRIVESHAFT HOUSING (1-5/8")	16-68165
9	STUD, CYLINDER BLOCK TO DRIVESHAFT HOUSING (4-3/8")	16-87901
10	STUD, (.312 x 2.125), CYLINDER BLOCK TO DRIVESHAFT HOUSING	16-68166
11	STUD, (.312-18/.312-24 x 2.560), CYLINDER BLOCK TO DRIVESHAFT HOUSING	16-68167
12	RESTRICTOR, CYLINDER BLOCK (BLEED)	66517
13	PIN, Dowel, CRANKCASE TO CYLINDER BLOCK	17-23784
14	PIN, Dowel, CYLINDER BLOCK TO MAIN BEARING	17-20323
15	GASKET, SEALING - CYLINDER BLOCK	27-55158
16	PLUG, Pipe (.125-27), CYLINDER BLOCK	22-328022
17	BRACKET, STARTER MOTOR	62064
18	SCREW, (.312-24 x 1.375), STARTER MOTOR BRACKET TO BLOCK	10-21339
19	NUT, (.312-24), STARTER MOTOR BRACKET SCREW	11-29250
20	SCREW, (.312-18 x 1.50), CRANKCASE TO CYLINDER BLOCK	10-73657
20	SCREW, (.312-18 x 3.00), CRANKCASE TO CYLINDER BLOCK	10-63328
20	SCREW, (.312-18 x 1.250), CRANKCASE TO CYLINDER BLOCK	10-74824
21	END CAP ASSEMBLY, Lower	1152-7267A1
22	SEAL, LOWER END CAP	26-41953
23	O-RING, LOWER END CAP	25-823683	25-64067
24	SCREW, END CAP TO CYLINDER BLOCK (1-1/2")	10-63365
25	O-RING, LOWER END CAP SCREW	25-64068
26	GASKET, CYLINDER BLOCK TO BAFFLE PLATE	27-854891
27	PLATE, DIVIDER - EXHAUST MANIFOLD	55190
28	GASKET, BAFFLE PLATE TO EXHAUST COVER	27-854882
29	COVER, EXHAUST MANIFOLD	551572
30	SCREW, (1.25), MANIFOLD COVER TO CYLINDER BLOCK	10-60411
30	SCREW, MANIFOLD COVER TO CYLINDER BLOCK (1-3/8")	10-31984
31	SCREW, ADJUSTING - EXHAUST COVER (1-7/8")	10-64021
32	NUT, (.250-20), ADJUSTING SCREW	11-64015
33	CAP, Nylon, ADJUSTING SCREW	26852
34	COVER, CYLINDER BLOCK	1024-91101
35	GASKET, CYLINDER BLOCK COVER	854901
36	SCREW, (.250-20 x 1.120), CYLINDER BLOCK COVER MOUNTING	10-76213
37	STRAP ASEMBLY, Ground, POWERHEAD TO BOTTOM COWL	46933A3
38	PLUG, Pipe (.125-27), CYLINDER BLOCK COVER	22-328022
39	COVER, TRANSFER PORT	430651
40	GASKET, TRANSFER PORT COVER	27-552791
41	SCREW, TRANSFER PORT COVER MOUNTING (1")	10-8M0214943
42	J CLIP, COIL HARNESS	54-47483
43	BRACKET, FUEL FILTER AND HARNESS	92059
44	SCREW, (.250-20 x 1.120), BRACKET MOUNTING	10-76213
-	GASKET SET	27-78028A78
-	POWERHEAD ASSEMBLY	61779A87

DRIVESHAFT HOUSING

Below is the parts list for Mercury 35 (2 CYL.) DRIVESHAFT HOUSING:

Position No.	Part Name	OEM Number	Supersedes
1	HOUSING ASSEMBLY, Driveshaft Comment: (SHORT SHAFT)	1592-8188A8
1	HOUSING ASSEMBLY, Driveshaft Comment: (LONG SHAFT)	1593-7513A12
2	STUD, (.375-16/.375-24 x 1.750), DRIVESHAFFT HOUSING	16-8M0022145	16-57932
2	STUD, (.375 x 6.75), DRIVESHAFT HOUSING Comment: (X-LONG)	16-97460
3	STUD, DRIVESHAFT HOUSING (3")	16-57935
3	STUD, (.4375 x 8.03) , DRIVE SHAFT HOUSING Comment: (X-LONG)	16-96124
4	PLUG, PLASTIC - WATER PICK-UP HOLE	19-64649
5	PLUG, (1/8 Inch Brass), DRIVESHAFT HOUSING	22-390721
6	WASHER, GEAR HOUSING STUDS	12-65791
7	NUT, (.437-20) Stainless Steel, GEAR HOUSING STUDS	11-8M0204653
8	COVER, TRIM - DRIVESHAFT HOUSING	60769
9	SCREW, (#10-16 x .750) Stainless Steel, TRIM COVER TO DRIVESHAFT HOUSING	10-57807
10	GROMMET, TRIM COVER SCREW	25-92012
11	TUBE, WATER OUTLET Comment: (SHORT SHAFT)	32-37727
11	TUBE, WATER OUTLET Comment: (LONG SHAFT)	32-45679
11	TUBE, WATER OUTLET Comment: (X-LONG SHAFT)	32-98856
12	TUBE, EXHAUST Comment: (SHORT SHAFT)	695431
12	TUBE, EXHAUST Comment: (LONG SHAFT)	695441
13	NUT, POWERHEAD STUDS	11-64809
14	MOUNT, RUBBER - UPPER	923373
15	SEAL, BELLOWS - UPPER MOUNT	96401
16	WASHER, UPPER MOUNT BOLT (37/64 I.D.)	12-27727
17	WASHER, RUBBER - UPPER MOUNT BOLT	12-66966
18	WASHER, UPPER MOUNT BOLT	12-30514
19	NUT, (.437-20) Stainless Steel, UPPER MOUNT BOLT	11-8M0204653
20	COVER, UPPER MOUNT	87883
21	SCREW, (.250-20 x 1.00), UPPER MOUNT COVER	10-8M0214943
22	WASHER, (.281 x .500 x .060) Stainless Steel, UPPER MOUNT COVER SCREW	12-8M0204649
23	SCREW, (.500-20 x 5.500), LOWER MOUNT	10-75284
24	WASHER, LOWER MOUNT SCREW	12-28051
25	WASHER, RUBBER - LOWER MOUNT SCREW	12-28053
26	MOUNT, RUBBER - LOWER	75302T1
27	WASHER, (.875 Inch Outside Diameter), LOWER MOUNT SCREW	12-30119
28	NUT, LOWER MOUNT SCREW	11-25096
29	CLAMP, LOWER MOUNT TO DRIVESHAFT HOUSING	69592F1
30	SCREW, (.312-18 x .875), LOWER MOUNT CLAMP	10-29256
31	SPRING, TENSION - LOWER MOUNT CLAMP	24-35522
32	CABLE ASSEMBLY, Ground	88238A10
33	COVER, LOWER MOUNT CLAMP	35474T
34	SCREW, (#12-14 x .920), COVER TO LOWER CLAMP	10-87884
35	NUT, LOWER MOUNT CLAMP COVER	11-35521
36	EXTENSION ASSEMBLY Comment: (X LONG SHAFT)	98858A1
37	SEAL, EXTENSION Comment: (X LONG SHAFT)	37721001

FLYWHEEL, IGNITION COIL AND SWITCH BOX

Below is the parts list for Mercury 35 (2 CYL.) FLYWHEEL, IGNITION COIL AND SWITCH BOX:

Position No.	Part Name	OEM Number	Supersedes
1	NUT, (.625-18), FLYWHEEL	11-8M0214915
2	WASHER, (.641 x 1.250 x .190), FLYWHEEL NUT	12-33001
3	FLYWHEEL ASSEMBLY Comment: (MANUAL)	242-7912A14
3	FLYWHEEL ASSEMBLY, 77 TEETH Comment: (ELECTRIC)	242-7912A12
4	INERTIA RING ASSEMBLY	41409A1
5	SCREW, (.250-28 x .625), FLYWHEEL	10-32417
6	RATCHET, FLYWHEEL Comment: MANUAL	50-65213
7	SCREW, (.312-24 x .750) Comment: MANUAL	10-68997
8	LOCKWASHER Comment: MANUAL	13-20202
9	STATOR Comment: (BOLT/NUT CONNECTORS)	86617A20
9	STATOR ASSEMBLY Comment: (BULLET CONNECTORS)	86617A20
10	SCREW, (#10-24 x 1.50)	10-77363
10	SCREW, (#10-24 x 1.00)	10-19926100
11	STATOR ASSEMBLY, CHARGING Comment: ELECTRIC	86704A10
12	SCREW, (#10-24 x 1.750) Comment: ELECTRIC	10-93787
13	SUPPORT, Stator	95707
14	TRIGGER PLATE Comment: (BOLT/NUT CONNECTORS)	92431A6
14	TRIGGER PLATE Comment: (BULLET CONNECTORS)	92431A6
15	COIL ASSEMBLY, Ignition	339-832757A4
16	NUT, Brass, COIL TERMINAL	10-32,11-45076
17	CABLE ASSEMBLY, Black, COIL COVER SCREW	84-60466A8
18	COVER, IGNITION COIL	76254
19	SCREW, (#10-24 x 1.750), COVER TO COIL BRACKET	10-69002
19	SCREW, (.190-24 x 2.125), COVER TO COIL BRACKET	10-93460
20	LEAD ASSEMBLY, SPARK PLUG (HIGH TENSION)	84-813715A1
21	BOOT/TERMINAL KIT Comment: FOR CANADA AND BELGIUM USE 33-68098 (CHAMPION #QL76V)	85-63709A1
22	SHEEL, SPARK PLUG BOOT	99213
23	SPARK PLUG (NGH#BUHW)	33-896329827	33-827C
23	SPARK PLUG Comment: CANADA/BELGIUM	33-14103550
24	J CLIP, LEAD WIRES	54-54457
25	TIE STRAP, (14.00 Inches)	61990
26	SWITCHBOX ASSEMBLY Comment: (BOLT/NUT CONNECTORS)	339-7452A3
26	SWITCHBOX ASSEMBLY Comment: (BULLET CONNECTORS)	339-7452A21
27	SCREW, SWITCH BOX TO BRACKET	10-23015
28	LOCKWASHER, External , GROUND	10,13-69432
29	NUT, Brass, SWITCH BOX TERMINAL	10-32,11-45076
30	HARNESS ASSEMBLY, PRIMARY Comment: (BOLT/NUT CONNECTION)	84-94295A1

FUEL PUMP AND FUEL LINE

Below is the parts list for Mercury 35 (2 CYL.) FUEL PUMP AND FUEL LINE:

Position No.	Part Name	OEM Number	Supersedes
1	PUMP ASSEMBLY, Fuel	76575A9
2	CHECK VALVE ASSEMBLY	21-8M0084275	21-13424A 1
3	DIAPHRAGM KIT	55278A4
4	NOT SOLD SEPARATE, GASKET	NSS
5	NOT SOLD SEPARATE, GASKET	NSS
6	RETAINER, CHECK VALVE	23004
7	SCREW, (#6-32 x .380), RETAINRER TO HOUSING	10-43725
8	SCREW, FUEL PUMP MOUNTING (1-5/8")	10-86885
9	PLUG, Pipe (.125-27), FUEL PUMP	22-328022
10	FITTING, PUMP INLET	22-64705
11	LINE, (57.00 Inches Bulk), FUEL FILTER TO PUMP (9")	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
12	FILTER ASSEMBLY, Fuel	35-889527A07	35-8M0111436, 35-87946A15
13	FILTER ASSEMBLY	35-87946Q04
14	SEAL, FUEL FILTER	25-897536	25-98277
15	LINE, (57.00 Inches Bulk), ADAPTOR TO FUEL FILTER (11")	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
16	FITTING, Barb (.250-18), FUEL LINE TO ADAPTOR	22-63187
17	WASHER, ADAPTOR	30188
18	SPRING, ADAPTOR STEM	24-23067T
19	O-RING, ADAPTOR STEM	25-16524
20	STEM, CHECK UNIT ADAPTOR	23069
21	ADAPTOR, CHECK UNIT (FUEL PUMP)	22833
22	SCREW, (.250-28 x 1.250), ADAPTOR TO BOTTOM COWL	10-56500
23	NUT, ADAPTOR SCREW	11-36069
24	NUT, (M6) Stainless Steel, FUEL FILTER	11-400212
25	FITTING, PUMP OUTLET	22-64705
26	LINE, (57.00 Inches Bulk), PUMP TO CARBURETOR (12-3/4")	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
27	CLAMP, FUEL LINE ATTACHING	54-68424
28	ELBOW, TELL TALE HOSE TO BLOCK	22-782792
29	HOSE, TELL TALE (6")	32-7568058
30	NOZZLE, TELL TALE HOSE TO COWL	69791
31	SLEEVE, NOZZLE	23-90882
32	CLAMP, NOZZLE	66849
33	SCREW, (#10-16 x .625) Stainless Steel, CLAMP TO BOTTOM COWL	10-48409
34	TIE STRAP, (4.00 Inches), NOZZLE	56762
-	GASKET SET	27-78028A78

GEAR HOUSING(DRIVESHAFT)

Below is the parts list for Mercury 35 (2 CYL.) GEAR HOUSING(DRIVESHAFT):

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY Comment: (SHORT SHAFT)	1643-9539A4
-	GEAR HOUSING ASSEMBLY Comment: (LONG SHAFT)	1643-9539A5
-	GEAR HOUSING ASSEMBLY Comment: (X-LONG SHAFT)	1643-9539A10
1	GEAR HOUSING ASSEMBLY, Mercury	1643-9539T1
2	CONNECTOR ASSEMBLY, SPEEDOMETER	22-85822A10
3	PIN, Dowel (.187 x .530)	17-8M0084726	17-85500
4	STUD, WATER PUMP/BASE (2-5/8")	16-33778
5	STUD, (.437-14/.437-20 x 2.190), GEAR HOUSING	16-8M0034453	16-57933
5	STUD, (.4375 x 7.22), GEAR HOUSING Comment: (X-LONG SHAFT)	16-96126
6	BEARING, Roller	31-62091T
7	SCREEN ASSEMBLY, WATER INTAKE	72849A1
8	SCREW, (#10-32 x 1.250), WATER INTAKE SCREEN TO GEAR HOUSING	10-36070
9	NUT, Stainless Steel, WATER INTAKE SCREEN SCREW	10-32,11-859124	11-45812
10	PLATE, SUPPORT-EXHAUST TUBE	92815
11	SEAL, EXHAUST TUBE	37721001
12	GEAR, Pinion	43-98097T
13	NUT, (.437-20), PINION GEAR TO DRIVESHAFT	11-55910
14	GASKET, WATER PUMP BASE TO GEAR HOUSING	27-19552
15	O-RING, WATER PUMP BASE	25-26722
16	BASE ASSEMBLY, Water Pump	46-77177A1
17	SEAL, Oil, WATER PUMP BASE	26-79831
18	SEAL, (1.254 x .312), WATER PUMP BASE	26-90562
19	PIN, Dowel, WATER PUMB BASE	17-35973
20	GASKET, LOWER-WATER PUMP BASE TO FACE PLATE	27-19553
21	FACE PLATE	32768
22	GASKET, UPPER-FACE PLATE TO WATER PUMP BODY	27-19551
23	IMPELLER, WATER PUMP	47-89983T
24	KEY, IMPELLER DRIVE	28-8M0032837	28-56662
25	BODY ASSEMBLY, Water Pump	46-77822A1
26	INSERT, WATER PUMP BODY	48753
27	SEAL, RUBBER-WATER INLET TUBE	26-38452
28	WASHER, NYLON-WATER PUMP BODY	12-38453
29	WASHER, (.281 x .500 x .060) Stainless Steel, BODY AND BASE STUDS	12-8M0204649
30	NUT, (.250-28) Stainless Steel, BODY AND BASE SUTDS	11-35888
31	O-RING, RUBBER	25-20273
32	SEAT ASSEMBLY	88868A1
33	SEAL, SPLINED	86304
34	SCREW, (.375-16 x .250), GREASE FILLER	10-79953Q04
35	SCREW, Magnetic, DRAIN	22-8M0058389	22-67892A06
36	WASHER, FILLER/DRAIN SCREW	12-191833
37	SLEEVE, LUBRICATION-DRIVESHAFT	88181
38	SHIM SET, BEARING TO GEAR HOUSING (.002-3-5-10-20)	15-92881A1
39	BEARING ASSEMBLY, Roller, TAPERED-DRIVESHAFT	31-8M0166756
40	DRIVESHAFT ASSEMLBY Comment: (SHORT SHAFT)	45-98179
40	DRIVESHAFT ASSEMBLY Comment: (LONG SHAFT)	45-98180
40	DRIVESHAFT ASSEMBLY Comment: (X-LONG SHAFT)	45-97442A2
41	SPRING, COMPRESSION-DRIVESHAFT	24-20254
42	PIN, DRIVESHAFT	17-30545
43	SHAFT ASSEMBLY, SHIFT	76063A1
43	SHAFT ASSEMBLY, SHIFT Comment: (X-LONG SHAFT)	97443A1
44	E RING	53-29641
45	O-RING, (.862 x .103), SHIFT SHAFT BUSHING	25-25439
46	BUSHING ASSEMBLY, SHIFT SHAFT	23-77631A2
47	SEAL, Oil, SHIFT SHAFT BUSHING	26-8M0204708
48	WASHER, RUBBER-SHIFT SHAFT BUSHING	12-77674
49	BASE	78036
50	CAM, REVERSE LOCKING	43308T1
-	WATER PUMP KIT	46-77177A3
-	SEAL KIT	26-79831A1
-	GASKET SET	27-78028A78

GEAR HOUSING(PROPELLER SHAFT)

Below is the parts list for Mercury 35 (2 CYL.) GEAR HOUSING(PROPELLER SHAFT):

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY Comment: (SHORT SHAFT)	1643-9539A4
-	GEAR HOUSING ASSEMBLY Comment: (LONG SHAFT)	1643-9539A5
-	GEAR HOUSING ASSEMBLY Comment: (X-LONG SHAFT)	1643-9539A10
1	GEAR HOUSING ASSEMBLY, Mercury	1643-9539T1
51	CAM, Shift Control	760394
52	SHIM SET, BEARING CUP TO GEAR HOUSING (.002-3-5-10)	15-38374A1
53	BEARING SET	31-38356A1
54	GEAR ASSEMBLY, Forward	43-55608T4
55	BEARING, Roller	31-21739
56	FOLLOWER, Cam	38441
57	SLIDE, CROSS PIN	20843
58	SPRING, RETAINING-CROSS PIN	24-38114
59	RATCHET, SLIDING CLUTCH	52-92911T
60	PIN, Cross	17-8M0020942	17-38113
61	SPRING, COMPRESSION-CAM FOLLOWER	24-39845
62	PROPELLER SHAFT	44-75365
63	GEAR, Reverse	43-79158T
64	WASHER, THRUST-REVERSE GEAR	12-32004
65	BEARING, Ball	30-20839T
66	O-RING, BEARING CARRIER	25-31986
67	CARRIER ASSEMBLY, Bearing	69386T1
68	BEARING, Needle	31-21700
69	SEAL, Oil, BEARING CARRIER	26-8M0205511
70	SEAL, Oil, BEARING CARRIER	26-8M0203757
71	KEY, LOCATING-BEARING CARRIER	28-30281
72	TAB WASHER, GEAR HOUSING COVER	14-53012
73	NUT, GEAR HOUSING	11-87763
74	TRIM TAB ASSEMBLY, GEAR HOUSING	97-31640Q4
75	SCREW, (.437-14 x 1.75), TRIM TAB TO GEAR HOUSING	10-66024
76	WASHER, (.406 x .750 x .104), DRIVESHAFT HOUSING STUD	12-8M0214963
77	NUT, (.375-24), DRIVESHAFT HOUSING STUD	11-8M0204726
78	WASHER, HOUSING TO STUD (7-16")	24-64791
79	NUT, (.437-20) Stainless Steel, STUD	11-8M0204653
80	THRUST HUB, FRONT	73345A1
81	TAB WASHER, PROPELLER NUT	14-8M0214942
82	PROP NUT KIT	11-69578Q1
-	GASKET SET	27-78028A78

HYDRAULIC PUMP ASSEMBLY(PLASTIC RESERVOIR)

Below is the parts list for Mercury 35 (2 CYL.) HYDRAULIC PUMP ASSEMBLY(PLASTIC RESERVOIR):

Position No.	Part Name	OEM Number
-	PUMP ASSEMBLY, Hydraulic	92975A32
1	O-RING, (.364. x .070), HYDRAULIC PUMP	25-48171
2	VALVE BODY AND GEAR ASSEMBLY	92975A32
3	SCREW, (#10-16 x .750), VALVE BODY TO RESERVOIR	10-69570
4	COUPLER AND SHAFT	392-7727
5	SEAL, RESERVOIR TO VALVE BODY AND GEAR	392-7735
6	RESEROVIR ASSEMBLY (PLASTIC)	392-7731
7	WASHER, THRUST - ARMATURE	392-7732
8	ARMATURE, FIELD AND FRAME	392-7729
9	FIELD AND FRAME ASSEMBLY	392-8261
10	BALL, COMMUTATOR END PLATE	392-7730
11	PLATE ASSEMBLY, COMMUTATOR END	392-8262
12	BRUSH SET, COMMUTATOR END PLATE	392-8989
13	SPRING SET, BRUSH TENSION	392-2529
14	BOLT SET, Thru- Plate and Frame to Reservoir	392-7733
15	FILL PLUG, RESERVOIR	392-7728

MISCELLANEOUS PARTS/ACCESSORIES

Below is the parts list for Mercury 35 (2 CYL.) MISCELLANEOUS PARTS/ACCESSORIES:

Position No.	Part Name	OEM Number
-	PARTS MANUAL, 35 Hp	90-43116
-	DECAL SET Comment: (BROWN)	37-13481A89
-	DECAL SET Comment: (SILVER)	37-13481A89
-	GASKET SET	27-78028A78
-	OPERATION MANUAL	90-445622

POWER TRIM COMPONENTS

Below is the parts list for Mercury 35 (2 CYL.) POWER TRIM COMPONENTS:

Position No.	Part Name	OEM Number	Supersedes
1	PUMP ASSEMBLY, Hydraulic (PLASTIC RESERVOIR)	92975A32
2	O-RING, (.364. x .070), MANIFOLD PLATE	25-48171
3	SCREW, (.375-16 x .250), FILLER - HYDRAULIC PUMP	10-79953Q04
4	WASHER, SEALING - FILLER SCREW	12-191833
5	SCREW, (#10-32 x .437), VENT - HYDRAULIC PUMP	10-62269
6	PLATE, MANIFOLD	45336
7	VALVE ASSEMBLY, Control	45197A2
-	O-RING, (.364. x .070), MANIFOLD PLATE (SEE REF. #2)	25-48171
8	O-RING, CONTROL VALVE (3/4" O.D.)	25-45254
9	O-RING, (.364. x .070), CONTROL VALVE	25-48171
10	O-RING, CONTROL VALVE (5/8" O.D.)	25-45253
11	SCREW, (.250-28 x 1.250)	10-56500
12	PLUG, CONTROL VALVE (1/2-20)	22-46008
13	HARNESS ASSEMBLY	84-79147A3
14	FUSE, 20 Ampere	88-8M0207796
15	CABLE ASSEMBLY, FUSE	84-95084A3
16	BRACKET, MOUNTING	45377T
17	SCREW, (.312-18 x 1.00)	10-35386
18	LOCKWASHER, (.312-24), MOUNTING BRACVKET SCREW	13-39107
19	NUT, (.312-18) Cad Plated, MOUNTING BRACKET SCREW	11-21908
20	BOLT, (.375-24 x 1.75), HYDRAULIC PUMP TO BOAT	10-31830
21	NUT, HYDRAULIC PUMP BOLT	11-82671112
22	BRACKET, MOUNTING - STARTER SOLENOID	94279
23	SCREW	10-28638
24	NUT,	10-32,11-8M0204718
25	SOLENOID, Starter	8M0185622
26	LOCKWASHER, Stainless Steel, SOLENOID TERMINAL	8,13-26995
27	NUT, Brass, SOLENOID TERMINAL	8-32,11-26419
28	LOCKWASHER, (.250) Stainless Steel, SOLENOID TERMINAL	13-26992
29	NUT, (.250-20) Brass, SOLENOID TERMINAL	11-94330
30	BOOT, RUBBER - STARTER SOLENOID TERMINAL	85-861680	85-96535
31	SCREW, (.250-20 x .500) Stainless Steel	10-41508
32	LINK, SOLENOID TO SOLENOID	94275
33	CABLE ASSEMBLY, Battery (POSITIVE)	84-79139A13
33	CABLE ASSEMBLY (NEGATIVE)	84-79138A1
34	WIRE, STARTER SOLENOID (BLACK)	84-61600A9
35	FUSE ASSEMBLY, 90 Ampere	88-79023T90
36	WASHER, Phenolic (.27 x .81 x .062), FUSE TERMINAL	12-96457
37	NUT, (.250-28), FUSE TERMINAL	11-21825

POWER TRIM CYLINDER REPAIR KITS

Below is the parts list for Mercury 35 (2 CYL.) POWER TRIM CYLINDER REPAIR KITS:

Position No.	Part Name	OEM Number
-	REPAIR KIT (SEE NOTE)	92188A2
1	Not Sold Separate, Cylinder Cap (#N.S.S.)
2	Not Sold Separate, O-Ring (1-1/4" x 1-1/2" x 1/8") (#N.S.S.)
3	Not Sold Separate, Spacer (#N.S.S.)
4	Not Sold Separate, O-Ring (1-7/8" x 2-1/16" x 3/32") (#N.S.S.)
5	Not Sold Separate, O-Ring (3/4" x 15/16" x 3/32") (#N.S.S.)
6	Not Sold Separate, O-Ring (1-1/2" x 1-3/4" x 3/32") (#N.S.S.)

PROPELLERS(RIGHT HAND ROTATION)

Below is the parts list for Mercury 35 (2 CYL.) PROPELLERS(RIGHT HAND ROTATION):

Position No.	Part Name	OEM Number
-	PROPELLER ASSEMBLY (ALUMINUM)(PITCH 10") Comment: 3 BLADES	48-73132A45
-	PROPELLER ASSEMBLY (ALUMINUM)(PITCH 12") Comment: 3 BLADES	48-73134A45
-	PROPELLER ASSEMBLY (ALUMINUM)(PITCH 13") Comment: 3 BLADES	48-73136A45
-	PROPELLER ASSEMBLY (ALUMINUM)(PITCH 14") Comment: 3 BLADES	48-73138A45
-	PROPELLER ASSEMBLY (ALUMINUM)(PITCH 15") Comment: 3 BLADES	48-73140A45
-	PROPELLER ASSEMBLY (ALUMINUM)(PITCH 17") Comment: 3 BLADES	48-73144A45

SHIFT CONTROL LINKAGE

Below is the parts list for Mercury 35 (2 CYL.) SHIFT CONTROL LINKAGE:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET, SHIFT ANCHOR - UPPER	87876A2
2	SCREW, (.312-18 x 1.50)	10-73657
3	SCREW, (.312-18 x 2.250)	10-67450
4	SCREW, (.312-18 x 1-3/4), BRACKET TO CRANKCASE	10-35385
5	SLIDE, SHIFT ACUTATING	87874
6	LATCH, SHIFT ACUTATING SLIDE (SHIFT CABLE)	56193
7	SCREW, LATCH TO SHIFT ACTUTING SLIDE	10-39620
8	SPRING, COMPRESSION - LATCH SCREW	24-27087
9	SLIDE, NYLON -ANCHOR BRACKET	75717
10	END CAP, NYLON - ANCHOR BRACKET SLIDE	39515
11	BRACKET, SHIFT ANCHOR - LOWER	87876A2
12	SCREW, (.250-28 x 1.62)	10-20012
13	NUT, (.250-28), UPPER ANCHOR BRACKET SCREW	11-826709109	11-33825, 11-35045
14	CUP, RETAINER - ANCHOR BRACKET (SHIFT CABLE BARREL)	39519
15	LEVER, NYLON - SHIFT CABLE LOCKING	87609A1
16	PIN, LOCKING LEVERA AND COVER FASTENING	17-47175
17	COVER, NYLON - SHIFT CABLE	90211
18	LINK, LOCKING LEVER TO COVER	87609A1
19	SHIFT SHAFT ASSEMBLY Comment: (SHORT SHAFT)	75104A7
19	SHIFT SHAFT ASSEMBLY Comment: (LONG SHAFT)	75104A8
20	WASHER, UPPER SHIFT SHAFT Comment: MANUAL	12-37998
21	COTTER PIN, UPPER SHIFT SHAFT Comment: MANUAL	18-26811
22	SWITCH ASSEMBLY Comment: ELECTRIC TILLER	87-88096A1
23	SCREW, (#6-32 x .750) Comment: ELECTRIC TILLER	10-30902
24	TERMINAL BLOCK Comment: ELECTRIC TILLER	86-45915
25	SCREW, (.190-32 x .50) Comment: ELECTRIC TILLER	10-25764
26	NUT AND LOCKWASHER, Comment: ELECTRIC TILLER	10-32,11-27164
27	SCREW, (#10-16 x .440) Comment: ELECTRIC TILLER	10-69079

STARTER MOTOR ASSEMBLY

Below is the parts list for Mercury 35 (2 CYL.) STARTER MOTOR ASSEMBLY:

Position No.	Part Name	OEM Number	Supersedes
-	STARTER MOTOR ASSEMBLY (10 PINION TEETH)	50-41583T
1	DRIVE KIT	90642
2	DRIVE ASSEMBLY (10 PINION TEETH)	43076T
3	PLATE ASSEMBLY, DRIVE END	68584
4	Not Sold Separate, THRU BOLT (BOSCH #SC-3803) (#N.S.S.)
5	LOCKWASHER, (.250) Stainless Steel	13-26992
6	Not Sold Separate, THRUST WASHER (BOSCH #WA-3122) (#N.S.S.)
7	ARMATURE	57384
8	BRUSH/SPRING KIT	898265016	75384, 75384 1
9	BUSHING, INSULATING	23-57387
10	Not Sold Separate, WASHER (BOSCH #WA-3074-1) (#N.S.S.)
11	WASHER, INPUT STUD	12-38013
12	LOCKWASHER, (.250) Stainless Steel	13-26992
13	NUT, (.250-20)	11-20890
14	END CAP ASSEMBLY, W/BRUSH HOLDER	57389

STARTER MOTOR, RECTIFIER AND WIRING HARNESS (ELECTRIC ONLY)

Below is the parts list for Mercury 35 (2 CYL.) STARTER MOTOR, RECTIFIER AND WIRING HARNESS (ELECTRIC ONLY):

Position No.	Part Name	OEM Number	Supersedes
1	RECTIFIER	8M0058226	816770T, 816770, 62351A 1, 83-70350A 1, 83-70350A 3
2	SCREW, (.190-32 x .62)	10-38055
3	NUT AND LOCKWASHER, , RECTIFIER FASTENING SCREW	10-32,11-27164
4	NUT, Brass, RECTIFIER TERMINAL	10-32,11-45076
5	SOLENOID ASSEMBLY, Choke	89-889274	54293A11
6	SCREW, (.312-18 x .75)	10-25299
7	LOCKWASHER, Stainless Steel, CHOKE SOLENOID TERMINAL	10,13-26996
8	NUT, Brass, CHOKE SOLONOID TERMINAL	10-32,11-45076
9	PLUNGER ASSEMBLY, CHOKE SOLENOID	89008A2
10	PLUG, BOTTOM COWL Comment: PART OF BOTTOM COWL ASSEMBLY	19-35827
11	FASTENER, PLUG TO BOTTOM COWL Comment: PART OF BOTTOM COWL ASSEMBLY	11-30428
12	HARNESS ASSEMBLY Comment: (BOLT/NUT CONNECTORS)	84-96219A8
12	HARNESS ASSEMBLY Comment: (BULLET CONNECTORS)	84-96219A8
13	FUSE, 20 Ampere	88-8M0207796
14	CABLE ASSEMBLY, FUSE	84-95084A2
15	CLAMP, WIRING HARNESS	88751
16	SCREW, (.190-32 x 1.12), WIRING HARNESS CLAMP	10-23702
17	SPRING, WIRING HARNESS CLAMP SCREW	24-28357
18	WASHER, (.203 x .562 x .060) Stainless Steel, WIRING HARNESS CLAMP SCREW	12-72761
19	CABLE ASSEMBLY, Positive - Battery	84-88439A3
19	CABLE ASSEMBLY, Battery - Negative	84-88439A4
20	BRACKET, HARNESS SUPORT	886201
21	SCREW, HARNESS SUPPORT BRACKET	10-73280
22	COVER, HARNESS SUPPORT BRACKET	88617
23	SCREW, (.250-20 x .620) Stainless Steel, HARNESS SUPPORT BRACKET COVER	10-28635
24	STARTER MOTOR ASSEMBLY (10 PINION TEETH)	50-41583T
25	SCREW (1-5/8 INCH)	10-35213
27	LOCKWASHER, (.250) Stainless Steel, CABLE TO STARTER MOTOR NUT	13-26992
28	NUT, (.250-20), CABLE TO STARTER MOTOR	11-20890
29	CABLE ASSEMBLY, STARTER TO SOLENOID (YELLOW)	84-88809A9
30	SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel	10-69035
31	SOLENOID, Starter	8M0185622
32	SCREW, (.250-20 x .500), SOLENOID TO BRACKET	10-98253
33	LOCKWASHER, (.250) Stainless Steel, STARTER SOLENOID SCREW	13-26992
34	NUT, Brass	8-32,11-26419
35	NUT, (.250-20) Brass	11-94330
36	BRACKET, STARTER MOTOR TO CRANKCASE	42729A1
37	SCREW, (.250-20 x .560)	10-32079
38	SCREW, (#10-32 x .500) Stainless Steel	10-69022
39	WASHER, (.203 x .406 x .040), BRACKET SCREW	12-89302
40	INSULATOR, STARTER SOLENOID	85-97861

STARTER REWIND

Below is the parts list for Mercury 35 (2 CYL.) STARTER REWIND:

Position No.	Part Name	OEM Number
1	NUT, SHEAVE SHAFT (LEFT HAND THREAD)	11-20166
2	TAB WASHER, SHREAVE SHAFT NUT	14-61004
3	GROMMET, STARTER HOUSING	25-39597
4	CABLE ASSEMBLY, INTERLOCK Comment: MANUAL	76141
5	SCREW, (#10-32 x .625) Comment: MANUAL	10-32228
6	SCREW, (#10-32 x .500) Stainless Steel Comment: MANUAL	10-69022
7	CAM, INTERLOCK Comment: MANUAL	428201
8	SCREW, (.312-18 x 1.120) Comment: MANUAL	10-76138
9	SPRING Comment: MANUAL	24-761401
10	ACTUATOR Comment: MANUAL	79371
11	SCREW Comment: MANUAL	10-76137
12	SPRING Comment: MANUAL	24-76139
13	WASHER Comment: MANUAL	12-30191
14	COTTER PIN Comment: MANUAL	18-26811
15	PULLEY, STARTER	55860
16	SCREW, (.190-32 x 1.250)	10-45210
17	WASHER, PULLEY SCREW	12-22887
18	SPACER, PULLEY SCREW	23-309772
19	RETAINER, STARTER ROPE	94121
20	NUT, PULLEY SCREW	11-24656
21	HOUSING ASSEMBLY, Starter Comment: SEE NOTE #1 ON ILLUSTRATION	76079A8
21	HOUSING, Starter Comment: SEE NOTE #2 ON ILLUSTRATION	760792
22	SHEAVE ASSEMBLY, Starter Comment: SEE NOTE #1 ON ILLUSTRATION	50-94338A1
22	SHEAVE ASSEMBLY, Starter Comment: SEE NOTE #2 ON ILLUSTRATION	50-44255A1
23	PAWL, Starter Comment: SEE NOTE #1 ON ILLUSTRATION	91936
23	PAWL, Starter Comment: SEE NOTE #2 ON ILLUSTRATION	44508
24	SCREW (1")	10-88759
24	SCREW, (.312-18 x 1.250)	10-88760
25	LOCKWASHER, (.312), STARTER HOUSING SCREW	13-8M0204647
26	PLATE, STARTER REWIND	61002
27	SPRING, STARTER REWIND	24-39502T02
28	BUSHING, SPRING GUIDE	23-87649
29	SPRING, STARTER PAWL	24-87651
30	E RING, STARTER PAWL	53-87706
31	SPACER, SHEAVE SHAFT	23-63061
33	LEVER	94962
34	WAVE WASHER	13-20160
35	SHEAVE SHAFT	87656
36	CABLE ASSEMBLY, Starter	50-12066Q10
36	ROPE AND HANDLE KIT, Manual/Emergency Start Comment: (FOR MANUAL STARTING)	47341A11
37	RETAINER KIT, Rope	79470A1
38	WASHER, STARTER REWIND	12-35559
-	STARTER ASSEMBLY, Rewind	76079A8

STEERING HANDLE

Below is the parts list for Mercury 35 (2 CYL.) STEERING HANDLE:

Position No.	Part Name	OEM Number	Supersedes
1	CAP, STEERING HANDLE GRIP	48416
2	NUT, (.250-28), STEERING HANDLE ARM	11-826709109	11-33825, 11-35045
3	WASHER, (.255 x .625 x .0312), STEERING HANDLE ARM	12-69056
4	GRIP, STEERING HANDLE ARM	58192A1
5	HOUSING, DRIVE WHEEL - STEERING ARM HANDLE	48414
6	DRIVE WHEEL/ROD ASSEMBLY	48516A1
7	ARM Comment: (USE WITH PUSH BUTTON SWITCH)	48405A2
7	ARM ASSEMBLY Comment: (USE WITH TOGGLE SWITCH)	48405A2
8	PLATE, COVER - DRIVE WHEEL	48519
9	GASKET, COVER PLATE	27-48518
10	SCREW, (#10-24 x .50)	10-72169
11	CONDUIT, CABLE	8885242
12	CABLE, Throttle	48520
13	BARREL, CONTROL LINKAGE	89578
14	SCREW, SET - THROTTLE CABLE GUIDE TUBE	10-824081	10-89601
15	TUBE, THROTTLE CABLE GUIDE	8M0026078	89566 1
16	GUIDE, THROTTLE CABLE	8M0204660
17	ANCHOR, THROTTLE CABLE	20007
18	SET SCREW, , THROTTLE CABLE ANCHOR	8-32,10-8M0204644
19	BRACKET, STEERING HANDLE	48404T8
20	CAP, STEERING HANDLE BRACKET	48416
21	SCREW, STEERING HANDLE BRACKET TO STEERING HANDLE	10-823597	10-48476
22	WASHER, STEERING HANDLE BRACKET (.505 I.D.)	12-48477
23	WASHER, NYLON - HANDLE BRACKET (.630 I.D.)	12-48526
24	BUSHING, NYLON - HANDLE BRACVKET (5/8" I.D.)	23-28919
25	SPACER, STEERING HANDLE BRACKET	23-48525
26	WASHER, NYLON - HANLDE BRACKET (1-35/64" O.D.)	12-38000
27	WAVE WASHER, STEERING HANDLE BRACKET	13-48478
28	WASHER, NYLON - HANDLE BRACKET (1-3/4" O.D.)	12-49636
29	NUT, (.500-20), STEERING HANDLE BRACKET SCREW	11-82671317
30	SCREW, (.375-24 x 1.00), BRACKET TO ENGINE	10-35786
31	TAB WASHER, BRACKET SCREW	14-43589
32	DETENT, SHIFT LEVER	78812A1
33	SCREW, (#10-16 x .625) Stainless Steel, SHIFT LEVER DETENT TO HANDLE BRACKET	10-48409
34	SHIFT LEVVER	485681
35	BUSHING, NYLON - SHIFT LEVER (3/8" I.D.)	23-48237
36	WASHER, (.406 x .734 x .063) Stainless Steel, SHIFT LEVER	12-34931
37	NUT, (.375-24), SHIFT LEVER TO STEERING HANDLE BRACKET	11-8M0204726
38	SHIFT ROD, SHIFT	8128061
39	ROD END, SHIFT ROD	48419T
40	BUSHING, NYLON - SHIFT ROD (1/4" I.D.)	23-48475
41	WASHER, (.273 x .437 x .031) Stainless Steel, SHIFT ROD	12-35950
45	COTTER PIN, SHIFT ROD	18-25191
43	KNOB, SHIFT LEVER	98530
45	PLUG, BOTTOM COWL - SHORTING SWITCH HOLE	19-35827
46	FASTENER, PLUG TO BOTTOM COWL	11-30428
47	SWITCH ASSEMBLY, Stop Comment: USE WITH TOGGLE SWITCH	87-11083A10
48	RETANER, STOP SWITCH Comment: USE WITH TOGGLE SWITCH	8M0032846	12044 1 USE WITH TOGGLE SWITCH
49	LANYARD ASSEMBLY Comment: USE WITH TOGGLE SWITCH	15920Q54
50	CLAMP, STOP SWITCH Comment: USE WITH TOGGLE SWITCH	54-648552
51	SCREW, (.190-32 x .38) Comment: USE WITH TOGGLE SWITCH	10-22654
52	NUT AND LOCKWASHER, Comment: USE WITH TOGGLE SWITCH	10-32,11-27164

THROTTLE AND SPARK ADVANCE LINKAGE

Below is the parts list for Mercury 35 (2 CYL.) THROTTLE AND SPARK ADVANCE LINKAGE:

Position No.	Part Name	OEM Number	Supersedes
1	CAM, Throttle, ACTUATOR	44405
2	SCREW, (.250-20 x 1.250), ADJUSTIN - THROTTLE CAM	10-63102
3	NUT, (.250-20), JAM - ADJUSTING SCREW	11-64015
4	CAP, Nylon, ADJUSTING SCREW	26852
5	BRACKET, THROTTLE CONTROL SHAFT	39522T
6	SCREW (1-7/8")	10-64021
7	NUT, (.250-20)	11-64015
8	CAP, Nylon, ADJUSTING SCREW	26852
9	SCREW, (.312-24 x 1.12)	10-20639
10	NUT, (.312-24), THROTTLE CONTROL BRACKET SCREW	11-29250
11	SCREW (2-3/8 INCHES)	10-34438
12	WASHER	12-25893
13	WAVE WASHER	13-62172
14	NUT, (.312-24)	11-29250
15	LINK ROD	95044
16	SWIVEL, LINK ROD	95045
17	LEVER, THROTTLE CONTROL	95049
18	SCREW, (.375-16 x 1.75)	10-818165	10-55337
19	BUSHING, THROTTLE CONTROL LEVER SCREW	23-55164
20	BUSHING, THROTTLE CONTROL LEVER SCREW	23-55171
21	SPRING, RETURN - SPARK ADVANCE LEVER	24-55162
22	LEVER, SPARK ADVANCE	95051
23	SCREW, (.190-32 x 1.50), ADJUSTING - ADVANCE LEVER	10-32627
24	NUT, Stainless Steel, JAM - ADJUSTING SCREW	10-32,11-68219
25	CAP, NYLON - ADJUSTIN SCREW	48039
26	WASHER, THROTTLE CONTROL LEVER SCREW	12-68410
27	LATCH, THROTTLE CONTROL LEVER	39483
28	SCREW, (.250-28 x .880)	10-69026
29	SPRING, COMPRESSION - LATCH SCREW	24-20099
30	NUT, (.250-28), LATCH SCREW	11-826709109	11-33825, 11-35045
31	BALL JOINT ASSEMBLY, SPARK ADVANCE LEVER	62459T
32	NUT, , BALL JOINT TO SPARK ADVANCE LEVER	10-32,11-46438
33	LINK ROD	61940
34	PIVOT, THREADED - TRIGGER PLATE TO LINK ROD	74897T

TOP COWL AND COWLING

Below is the parts list for Mercury 35 (2 CYL.) TOP COWL AND COWLING:

Position No.	Part Name	OEM Number
1	TOP COWL ASSEMBLY Comment: (ELECTRIC)	2138-6341
1	TOP COWL ASSEMBLY Comment: (MANUAL)	2138-6340A2
2	ROPE GUIDE, STARTER ROPE	58657
3	RING, RETAING - ROPE GUIDE	53-72168
4	SHILD, REAR - TOP COWL	62236
5	SCREW, (#10-16 x .625) Stainless Steel, REAR SHIELD TO TOP COWL	10-48409
7	HOOK, TOP COWL LATCH - REAR	55455
8	SCREW, (.250-28 x .880), REAR HOOK TO TOP COWL	10-22956
9	LOCKWASHER, (.250) Stainless Steel, REAR HOOK SCREW	13-26992
10	PLATE, HINGE	75973
11	SCREW, (#10-32 x .625), HINGE PLATE	10-32228
12	LOCKWASHER, Stainless Steel, HINGE PLATE SCREW	10,13-26996
13	LEVER, COWL LATCH	94918F1
14	HINGE, COWL LATCH LEVER	52739
15	PIN, HINGE TO LEVER	17-58998
16	WRAP AROUND COWL ASSEMBLY (W/O DECALS)	2137-3878A6
17	LATCH ASSEMBLY, Cowl	46785A1
18	HOOK, COWL LATCH FASTENING	30413
19	COVER ASSEMBLY, Cowl - Front (W/O DECALS)	2161-6347A20
20	BLANKET, COWL FRONT COVER	76450

TRIM CYLINDERS AND HYDRAULIC HOSES

Below is the parts list for Mercury 35 (2 CYL.) TRIM CYLINDERS AND HYDRAULIC HOSES:

Position No.	Part Name	OEM Number	Supersedes
1	TRIM CYLINDER	92194A14
2	FITTING, Grease, TRIM CYLINDER	22-8M0169589
3	SCREW, (#10-32 x .3125), BLEED	10-45265
4	O-RING, BLEED SCREW	25-45016
5	SCREW, (.500-20 x 1.500), TRIM CYLINDER	10-92050
6	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel, TRIM CYLINDER BOLT	12-8M0204648
7	SPACER, TRIM CYLINDER - LOWER	23-45280
8	BUSHING, RUBBER - TRIM CYLINDER	23-94907A1
9	BRACKET, TRIM CYLINDER (PORT)	89108A3
10	SEAL, Oil, PORT BRACKET	26-70608
11	PLUNGER, LIMIT SWITCH ACTUATING	89290
12	SPRING, TENSION - LIMIT SWITCH PLUNGER	24-95881
13	STUD, (.312 x 18.880), MOUNTING BRACKET	16-62888
14	LOCKWASHER, (.312), MOUNTING BRACKET STUD	13-8M0204647
15	NUT, (.312-24) Stainless Steel, MOUNTING BRACKET STUD	11-28770
16	SCREW, (.500-20 x .2.250), MOUNTING BRACKET	10-45263
17	BOLT, (.375-16 x 3.250)	10-68298
17	SCREW, (.375-16 x 5.00)	10-89673
18	WASHER, MOUNTING BRACKET BOLT	12-68410
19	NUT, MOUNTING BRACKET BOLT	11-82671112
20	BRACKET, TRIM CYLINDER (STARBOARD)	89111T
21	SCREW, (.437-20 x 3.560)	10-45328
22	WASHER	12-37807
23	NUT, (.437-20), TRIM CYLINDER SCREW	11-8M0143423
24	SPRING, TENSION - ADJUSTING STUD	24-24390
25	STUD, (#10-32 x .930), ADJUSTING - CUT-OUT LIMIT SWITCH	16-8M0034461	16-21085
26	NUT, Stainless Steel, JAM - LIMIT SWITCH ADJUSTING STUD	10-32,11-859124	11-45812
27	CAM, LIMIT SWITCH ADJUSTING STUD	99897
28	PLATE, RETAINING - LIMIT SWITCH CAM	86967
29	SCREW, (#10-32 x .375) Stainless Steel, RETAINING PLATE AND CAM	10-68513
30	LOCKWASHER, Stainless Steel, RETAINING PLATE AND CAM SCREW	10,13-26996
31	SWITCH ASSEMBLY, CUT-OUT LIMIT	45326A2
32	BUSHING, RUBBER - CUT-OUT LIMIT SWITCH	23-45354
33	SCREW, (#4-40 x .625), CUT-OUT LIMIT SWITCH	10-47255
34	COVER, LIMIT SWITCH	89272
35	GASKET, LIMIT SWITCH COVER	27-892731
36	SCREW, (#10-32 x 1.00) Stainless Steel, LIMIT SWITCH COVER	10-34994
37	WASHER, LIMIT SWITCH COVER SCREW	12-38833
38	COVER, INLET - TRANSOM	87774A1
39	GASKET, INLET COVER	27-87775
40	GROMMET, RUBBER - INLET COVER	25-45507
41	SCREW, (#10-32 x 1.250), INLET COVER TO BOAT	10-36070
42	LOCKWASHER, Stainless Steel, INLET COVER SCREW	10,13-26996
43	NUT, Stainless Steel, INLET COVER SCREW	10-32,11-68219
44	HOSE, TRIM	32-88005
45	HOSE, LIFT	32-88006
46	GROMMET Comment: RUBBER (3/8" I.D. - 1" LONG)	23-35977
46	GROMMET Comment: RUBBER (3/8" I.D. - 7/8" LONG)	23-35977
46	GROMMET Comment: RUBBER (7/16" I.D. - 7/8" LONG)	25-12602002
47	STRAP, Tilt Stop	73519A1
48	TUBE, MOUNTING - TILT STOP	69259
49	PIN, MOUNTING TUBE	69258
50	TUBE, CUSHION	63473
51	COTTER PIN, MOUNTING TUBE PIN	18-36002
52	SPACER, MOUNTING BRACKET SCREW	23-59623

Download this page as PDF: Click here

For Mercury Owners:

To assist you in maintaining and repairing your marine engines, we hope the following resources may be of use:

Mercury / Mercruiser / Mariner Parts from JLM Marine

About JLM Marine

Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.

As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.

We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.