Mercury 250 (3.0L EFI) (1B504989 & Up) Outboard Motor Parts Diagram & Catalog – Free PDF Download

by JLM Marine 30 Apr 2025 0 Comments

Mercury 250 (3.0L EFI) Outboard Motor Parts Diagram & Catalog – Free PDF Download

Accessories

Below is the parts list for Mercury 250 (3.0L EFI) Accessories:

Part Name	OEM Number	Supersedes
FLUSH COUPLING	22-852400	56-820386A55
DECK FILL KIT, Oil	15969A3
DIODE ASSEMBLY (DUAL ENGINE)	812497A2
FLUSHING ATTACHMENT	44357Q2
HOSE ASSEMBLY, Fuel	32-858610A31	32-858610A10, 32-16789A18
HOSE ASSEMBLY, Fuel (12 Feet) Comment: (NO FITTINGS)	32-877683Q12	32-858623Q12, 32-858623A12, 32-822379A12, 32-819380A12, FA599752, FS409752, 32-819380A 3, F216752, FA409752, F289752, FA178752, FA216752, FA284752, FA289752, FS409952 (NO FITTINGS)
SWITCH/LANYARD KIT	87-19674Q2
MERCATHODE KIT	88334A2
HOSE EXTENSION KIT	41729A3
NOT SOLD SEPARATE, Rigging Hose Kit Comment: (SEE PARTS BULLETIN 99-4)	NSS
RESERVOIR KIT, Oil	15943A1
TRIM REDUCER KIT	858915A1

Attenuator/Flywheel Cover

Below is the parts list for Mercury 250 (3.0L EFI) Attenuator/Flywheel Cover:

Position No.	Part Name	OEM Number	Supersedes
1	COVER, Flywheel	892854T01	880009T02, 880009T 1
2	GROMMET, (.88 Inside Diameter)	25-13467
3	GROMMET	25-8M0153609
4	PLUG	19-89219001
5	ATTENUATOR ASSEMBLY	881909T3
6	BUSHING	23-856954
7	GROMMET	25-8M0190980
8	SEAL	882767
9	GROMMET	25-20116
10	CLIP	54-23567
11	WASHER, (.265 x .750 x .048) Stainless Steel	12-65567
12	SCREW, (M6 x 25)	10-82130025
13	DECAL, Caution-Start in Gear	37-881865	37-825064
14	SCREW, (#10-16 x .750)	10-69570

Bottom Cowl

Below is the parts list for Mercury 250 (3.0L EFI) Bottom Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	BOTTOM COWL, Port	100-8M0107324	113-850302A07
2	PLUG	854367001	854367
3	BOTTOM COWL, Starboard	100-8M0107323	113-850301A07
4	GASKET KIT	27-889246A97
5	SCREW, (M6 x 40)	10-82130040
6	SCREW, (M6 x 75)	10-824868
7	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
8	FRONT HANDLE	8M0053903	850684F 1
9	BUSHING	23-335891
10	O-RING, (.614 x .070)	25-48462
11	PAWL	8219423
12	WASHER, (.281 x .734 x .063)	12-69057
13	NUT, (M6) Stainless Steel	11-401366
14	SCREW, (#10-16 x .625)	10-8214281
15	CLIP	54-822873
16	SWITCH, Trim	87-8M0235191
17	RIGGING KIT (Upper)	8M8027677	54-859359A 2
18	NOT SOLD SEPARATE, Clamp-Lower	NSS
19	SCREW, (M6 x 12)	10-82130012
20	NOT SOLD SEPARATE, Strap	NSS
21	FOAM	859343
22	TIE STRAP, (11.750 Inches)	54-850181
23	HANDLE	852361T02
24	SEAL, (44.00 Inches)	8M0109218

Coil Plate

Below is the parts list for Mercury 250 (3.0L EFI) Coil Plate:

Position No.	Part Name	OEM Number	Supersedes
1	PLATE, Coil Mounting	850295T2
2	COIL KIT	300-8M0077471	300-879984T01, 339-879984A 1, 339-879984T00
3	SCREW, (M6 x 30)	10-82129130
4	CABLE SET	84-881908T	84-821945T74, 84-821945T65
5	CLIP (Included with Coil Harness)	54-828991T	54-828991
6	SPARK PLUG	33-941
7	HARNESS ASSEMBLY, Coil	84-882757T02
-	HARNESS ASSEMBLY, 5 Pin	879346A51	84-854839T02
8	CABLE ASSEMBLY, Braided	84-858414A1
9	SCREW, (M6 x 10)	10-82129110
10	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
11	GROMMET	25-833155
12	WASHER	12-4002318
13	BUSHING	23-8502341
14	SCREW, (M8 x 35)	10-81893435
15	SENSOR KIT, (0-50 PSI)	71-8M0157742
16	FITTING	22-8M0207782
17	CLIP, (.865)	54-883066
18	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
19	TUBING, (52.00 Inches Bulk) (Cut to 18 Inches)	32-85978571
20	WASHER	12-36001

Crankshaft, Pistons and Connecting Rods

Below is the parts list for Mercury 250 (3.0L EFI) Crankshaft, Pistons and Connecting Rods:

Position No.	Part Name	OEM Number	Supersedes
1	CRANKSHAFT ASSEMBLY	482-9784A11
2	WEAR SLEEVE	830882
3	BEARING, Ball (Lower)	30-67923T
4	RING	53-67446
5	RING, Seal	39-843198T01	39-843198001, 39-816106
6	KEY, Woodruff	28-91800
7	O-RING, (.859 x .139)	25-35126
8	BEARING/RACE KIT	31-88270A02
9	NOT SOLD SEPARATE, Bearing-Center Main	NSS
10	PISTON ASSEMBLY, Standard - Starboard	700-858295T14	700-858295T 1
10	PISTON ASSEMBLY, Standard - Port	700-858294T14	700-858294T 1
10	PISTON ASSEMBLY Comment: (Starboard - .015 oversize)	700-878572A2
10	PISTON ASSEMBLY Comment: (Port - .015 oversize)	700-878571A2
10	PISTON ASSEMBLY Comment: (Starboard - .030 oversize)	700-878574A2
10	PISTON ASSEMBLY Comment: (Port - .030 oversize)	700-878573A2
11	RING	40-841202
12	RING SET, Piston	39-858772A12
13	NOT SOLD SEPARATE, Piston Ring-Lower	NSS
14	CONNECTING ROD ASSEMBLY	600-8M0125869
15	SCREW, (.375-24 x 1.250)	10-94320
16	BEARING ASSEMBLY	31-844338A01	31-43012A04
17	NOT SOLD SEPARATE, Needle Roller Bearing	NSS
18	THRUST WASHER	12-88263
19	BEARING, Needle	29-8M0204715
20	BEARING ASSEMBLY (Upper)	31-816773A2
21	SEAL	26-859093	26-815449
22	O-RING, (1.989 x .070)	25-823683	25-64067
-	GASKET SET, Powerhead	27-832934A00
-	POWERHEAD ASSEMBLY Comment: (200)	891823A07	891823A04, 891823B04 (200)
-	POWERHEAD ASSEMBLY Comment: (225)	883892A07	883892A04, 883892A03, 883892A02 (225)
-	POWERHEAD ASSEMBLY Comment: (250)	883894A07	883894A04, 883894A03, 883894A02 (250)

Cyliner Block and End Cap

Below is the parts list for Mercury 250 (3.0L EFI) Cyliner Block and End Cap:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER BLOCK ASSEMBLY Comment: (200)	885-899162A05	885-9811T91 (200)
1	CYLINDER BLOCK ASSEMBLY Comment: (225)	885-899162A06	885-9811T92 (225)
1	CYLINDER BLOCK ASSEMBLY Comment: (250)	885-899162A07	885-9811T93 (250)
2	SCREW, (M8 x 40)	10-81893440
3	BRACKET	8M0111325
4	STUD, (M10 x 1.5 x 64)	16-903509
5	STUD, (M10 x 1.5 x 155)	16-8154431
6	DEFLECTOR	8248577
7	CHECK VALVE	21-8781051
8	PIN	17-8M0036405	17-67296
9	PIN, Dowel - Without Hole (.375 x .625)	17-43044
10	SCREW, (M10 x 80)	10-82446180
11	SCREW, (M8 x 35)	10-81893435
12	SCREW, (M8 x 20)	10-81893420
13	PIN, Dowel (.250 x .625)	17-63779
14	SENSOR ASSEMBLY, Temperature	13536A13
15	PIN	17-8405101
16	RETAINER	8588641
17	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963
18	NUT, (M10) Stainless Steel	11-4013610
19	SENSOR	8M0082988	8M0030022, 828358 2
20	SCREW, (M5 x 16) Stainless Steel	10-40011107
21	END CAP ASSEMBLY	1171-9787A4
22	O-RING, (3.237 x .103)	25-62700
23	SEAL	26-8308981
24	SCREW, (M6 x 20)	10-82130020
25	PLATE ASSEMBLY	857186T02	857186A 1
26	MOUNT	23-855729
27	SCREW, (M10 x 45)	10-82130145
28	SCREW, (M6 x 10)	10-82494810
29	GROMMET	25-19565002
30	WASHER	12-855725
31	RETAINER	137151
32	J CLIP	54-858951
33	SCREW, (M6 x 12)	10-82130012
34	SEAL	818574
35	CYLINDER HEAD ASSEMBLY	812851A27	812851A22, 812851A19
36	SEAL	884391
37	THERMOSTAT, 54 Degree C/130 Degree F	8M0057307	885599004, 885599003, 885599 1
38	GASKET	27-8503181
39	COVER, Thermostat	8M0039357	887926
40	SCREW, (M6 x 25)	10-82130025
41	SCREW, (M8 x 50)	10-8M0045380	10-891570050, 10-859096, 10-824460 50, 10-891570
42	SENSOR ASSEMBLY	8M0148668
43	O-RING, (1.78 mm x .08 mm)	25-896699	25-888814
44	SCREW, (M8 x 14)	10-81893414
45	FITTING, Elbow 45 Degree (1.25)	22-782792
46	LEVER, TPI	8583561
47	SCREW, (M6 x 25)	10-82130025
48	BUSHING	23-856954
49	GROMMET	25-8M0190980
50	WASHER, (.265 x .750 x .048) Stainless Steel	12-65567
51	SCREW, (M5 x 45) Stainless Steel	10-40011113
52	INDICATOR, Throttle Position	8M6005165
53	LINK	8M0084743
54	CLAMP	54-858902
55	COVER	8582261
56	BRACKET	8544862
57	CLAMP, (25.6 mm)	54-855228	54-888988014
58	FITTING	22-8533394
59	HOSE (Starboard)	32-8404461
60	HOSE (Port)	32-8404462
61	SENSOR ASSEMBLY, Knock Comment: (200)	8M6003194	878187 (200)
62	STUD Comment: (200)	16-882781
63	NUT, (M10) Brass/Nickel Plated Comment: (200)	11-826292
-	GASKET SET, Powerhead	27-832934A00
-	POWERHEAD ASSEMBLY Comment: (200)	891823A07	891823A04, 891823B04 (200)
-	POWERHEAD ASSEMBLY Comment: (225)	883892A07	883892A04, 883892A03, 883892A02 (225)
-	POWERHEAD ASSEMBLY Comment: (250)	883894A07	883894A04, 883894A03, 883894A02 (250)

Deck Oil Fill Kit, 15969A3 or 15969A5

Below is the parts list for Mercury 250 (3.0L EFI) Deck Oil Fill Kit, 15969A3 or 15969A5:

Position No.	Part Name	OEM Number	Supersedes
1	DECK FILL KIT, Oil, With Hose	15969A3
2	DECK FILL KIT, Oil, With Out Hose	15969A13
3	PLATE	15966
4	DECK PLATE ASSEMBLY	15969A08
5	SCREW, (#8 x .625)	10-16324
6	CLAMP, Worm Gear	54-815504228	54-32781, 54-853232, 54-853432
7	ADAPTOR, Oil Filler	15967
8	O-RING, (2.225 x .210)	25-11332
9	HOSE, (100.00 Feet Bulk) , Oil Filler - Cut as Required	32-850719

Driveshaft Housing and Exhaust Tube

Below is the parts list for Mercury 250 (3.0L EFI) Driveshaft Housing and Exhaust Tube:

Position No.	Part Name	OEM Number	Supersedes
1	HOUSING ASSEMBLY, Driveshaft - Long	3518-832937A06	3518-832937A05, 3518-832937A 3, 3518-832937A 4
1	HOUSING ASSEMBLY, Driveshaft - X/XX-Long	3519-832938A06	3519-832938A 5
2	STUD, (M12 x 52) Comment: Long/X-Long	16-8M0008031	16-856983, 16-822257 Long/X-Long
3	SCREW, (M12 x 35 MM) Comment: Long/X-Long	10-857136
4	GROMMET	25-8331231
5	WASHER, (.500 x .810 x .090) Stainless Steel	12-856982
6	NUT, (M12)	11-896895	11-857008
7	PLUG	19-64649
8	BOLT, (M14 x 178)	10-898834	10-815431002, 10-815431
9	CABLE ASSEMBLY, Ground	88238A10
10	WASHER, (.562 x 2.00 x .125)	12-815432
11	WASHER, (1.25 x 2.00 x .19)	12-8154331
12	MOUNT	8137711
13	WASHER	12-825190
14	NUT, (M14)	11-896602	11-815434, 11-815434002
15	CLAMP, When Depleted Order Design II Kit 879150A90 Comment: Design I SN# 1B775625 & Below	8186442
16	SCREW, (M8 x 35)	10-81893435
17	LOCKWASHER, Internal Tooth	13-72521
18	COVER, Lower Mount, When Depleted Order Design II Kit 879150A90 Comment: Design I SN# 1B775625 & Below	8M0001136	818645F 1 Design I SN# 1B775625 & Below
19	SCREW, (#10-16 x .440) Comment: Design I	10-69079
20	SEAL	8329321
21	TUBE ASSEMBLY, Exhaust	833116A19	833116A17
22	STRAINER	35-8M0026113	35-852405 2
23	SCREW, (M8 x 35)	10-81893435
24	TUBE, Water Comment: Long	32-8M0042785	32-832941 7 Long
24	TUBE, Water Comment: X-Long	32-8M0042786	32-832941 8 X-Long
24	TUBE, Water Comment: XX-Long	32-8M0042787	32-832941 9 XX-Long
25	SEAL	832940001	832940
26	CLAMP	8329391
27	SCREW, (.250-20 x .500) Stainless Steel	10-41508
28	SPACER Comment: XX-Long	8M0105088	8M0071622, 880647T04, 823979T 1, 880647T02, 880647T XX-Long
29	PIN, Dowel - Without Hole (.375 x .625) Comment: XX-Long	17-43044
30	STUD, (M12 x 179) Comment: XX-Long	16-8M0008047	16-857009, 16-824117 XX-Long
31	SCREW, (M12 x 160) Comment: XX-Long	10-857137
32	SCREW, (M8 x 35)	10-81893435
33	COVER KIT, Lower Mount Comment: Design II SN# 1B775625 & Below	879150A90
34	COVER, Lower Mount Comment: Design II SN# 1B775626 & Up	100-8M0148785
35	CLAMP Comment: Design II SN# 1B775626 & Up	100-8M4501003
36	SCREW, (#10-16 x .440) Comment: Design II SN# 1B775626 & Up	10-69079
37	WASHER	12-847541
38	WASHER, (.500 x .810 x .090) Stainless Steel	12-856982

Dual Engine Tie Bar Kit

Below is the parts list for Mercury 250 (3.0L EFI) Dual Engine Tie Bar Kit:

Position No.	Part Name	OEM Number	Supersedes
-	EXTENSION KIT, Dual Engine	92876A9
1	TUBE ASSEMBLY	71565A2
2	O-RING, (.614 x .070)	25-48462
3	MOUNT	41055
4	TAB WASHER	14-42100
5	NUT, (.875-14)	11-8M0041651	11-37984
6	TAB WASHER	88404
7	SCREW, (.250-28 x 1.250)	10-38601
8	BRACKET	17729A1
9	SCREW, (.312-24 x 1.250)	10-62055
10	TAB WASHER	17728
11	SCREW, (.375-24 x 1.38)	10-140001
12	NUT, (.375-24) Stainless Steel	11-8M0204726
13	STEERING EYE	8M0026167	8M0005848, 97933 1
14	SLEEVE, (1.625)	23-23651
15	TUBING, (4.00 Inches)	97931
16	COUPLER, 15 In.	8M0026098	814951 3
17	NUT, (.562-18)	11-42099
18	COUPLING	22-821169
19	WASHER, (.406 x .734 x .063) Stainless Steel	12-34931
19	WASHER, (.390 x .625 x .062) Stainless Steel	12-37828
20	SCREW, (.375-24 x 1.5)	10-94319

Exhaust Plate

Below is the parts list for Mercury 250 (3.0L EFI) Exhaust Plate:

Position No.	Part Name	OEM Number	Supersedes
1	PLATE ASSEMBLY, Exhaust	832935A17	832935A16, 832935A15, 832935A14
2	GASKET	27-832933006
3	GASKET (Lower)	27-832934006
4	SEAL	8M0043157	823805 1
5	FITTING, Check Valve	22-8320761
6	PLUG, Pipe (.375-18) Brass	22-8M0180565
7	CHECK VALVE ASSEMBLY, Drain	21-817519A1
8	PIN, Dowel - Without Hole (.375 x .625)	17-43044
9	GROMMET	25-822002
10	PLUG	19-48323
11	COVER ASSEMBLY	65663A2
12	SCREW, (M8 x 35)	10-81893435
13	CARRIER	814190
14	GROMMET	25-814191
15	POPPET	814189
16	SPRING, (Black)	24-64878
17	PLATE ASSEMBLY	65664A1
18	GASKET	27-88907003
19	DIAPHRAGM	648771
20	WASHER	12-76451
21	SCREW, (#10-16 x .750)	10-69570
22	SCREW, (M8 x 35)	10-81893435
23	BOOT KIT, Idle Exhaust Comment: Includes references 44 and 45	850306A04	850306 1 Includes references 44 and 45
24	CLAMP, (28.6)	54-850896
25	FITTING, Tell-Tale	22-8M0077650	821904
26	PLUG	19-821908
27	WASHER	12-821915
28	FITTING	22-8596001
29	CHECK VALVE	8219631
30	O-RING, (.299 x .103)	25-30641
31	BUSHING	23-48237
32	COUPLING Comment: Design I	43585
33	FITTING, Straight	22-858855
34	GROMMET	25-12602002
35	HOSE, (57.00 Inches Bulk) (Cut to 3 Inches)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
36	FLUSH HOSE KIT (Inlet)	32-859626A1
37	PLATE	888910
38	SCREW, (M5 x 12)	10-82239312
39	COUPLER, Shift Shaft Comment: Design II	8M0027417
-	GASKET SET, Powerhead	27-832934A00
-	POWERHEAD ASSEMBLY Comment: (200)	891823A07	891823A04, 891823B04 (200)
-	POWERHEAD ASSEMBLY Comment: (225)	883892A07	883892A04, 883892A03, 883892A02 (225)
-	POWERHEAD ASSEMBLY Comment: (250)	883894A07	883894A04, 883894A03, 883894A02 (250)

Flywheel/Alternator

Below is the parts list for Mercury 250 (3.0L EFI) Flywheel/Alternator:

Position No.	Part Name	OEM Number	Supersedes
1	ALTERNATOR	8M6013461
2	SPRING	24-8523742
3	ARM TENSIONER ASSEMBLY	856815T2
4	WASHER	12-4002320
5	BUSHING	23-8568941
6	STUD, (M10 x 85)	16-8M0034457	16-856900
7	NUT, (M10) Brass/Nickel Plated	11-826292
8	PULLEY ASSEMBLY	8M6005030
9	SCREW, (M10 x 35) Hex Flange - Stainless Steel	10-4010835
10	BELT	57-828507Q11	57-828507 11
11	FLYWHEEL	283-859619T1
12	NUT, (M16)	11-42979
13	WASHER, (.641 x 1.250 x .190)	12-33001
14	PLUG, Yellow	19-45907
15	NUT, (M6) Stainless Steel	11-401386
16	CABLE ASSEMBLY	84-856583A5
17	WASHER	12-4002319
18	SCREW, (M10 x 50)	10-82130150
19	SCREW, (M6 x 12)	10-82130012

Fuel Line Assembly

Below is the parts list for Mercury 250 (3.0L EFI) Fuel Line Assembly:

Position No.	Part Name	OEM Number	Supersedes
1	HOSE ASSEMBLY, Fuel (5.50 Feet-18/42.00 Inches) Comment: (2008 and Below)	32-858610A39	32-858610A21 (2008 and Below)
1	HOSE ASSEMBLY, Fuel (8.00 Feet-30.00/60.00 Inches) Comment: (2008 and Below)	32-858610A33	32-858610A12 (2008 and Below)
1	HOSE ASSEMBLY, Fuel (9.00 Feet-42.00/60.00 Inches) Comment: (2008 and Below)	32-858610A31	32-858610A10, 32-16789A18 (2008 and Below)
1	HOSE ASSEMBLY, Fuel (9 Feet) With Primer Bulb Comment: (2009 and Up)	32-8M8025356	32-8M0038610 (2009 and Up)
1	HOSE ASSEMBLY, Fuel (12 Feet) (12.00 Feet-30.00/108.00 Inches) Comment: (2008 and Below)	32-877683Q12	32-858623Q12, 32-858623A12, 32-822379A12, 32-819380A12, FA599752, FS409752, 32-819380A 3, F216752, FA409752, F289752, FA178752, FA216752, FA284752, FA289752, FS409952 (2008 and Below)
1	HOSE ASSEMBLY, Fuel (12 Feet) Quicksilver Branded Comment: (2009 and Up)	32-8M0044841	32-858110Q12 (2009 and Up)
1	HOSE ASSEMBLY, Fuel (12.00 Feet-30.00/108.00 Inches) Comment: (2008 and Below)	32-877683T12	32-858623T12 (2008 and Below)
1	HOSE ASSEMBLY, Fuel (12 Feet) Mercury Branded Comment: (2009 and Up)	32-8M0044837	32-858108K12 (2009 and Up)
2	HOSE, (9.00 Feet Bulk) Comment: (2008 and Below)	32-85861079
2	HOSE, (9.00 Feet)(108.00 In.) Bulk Comment: (2009 and Up)	32-8M0038468
2	HOSE, (100.00 Feet Bulk) Comment: (2008 and Below)	32-858610100	32-16789100 (2008 and Below)
2	HOSE, (100.00 Feet Bulk) Comment: (2009 and Up)	32-8M0038500
3	BULB ASSEMBLY, Primer (Yellow Washer)	13330K07
3	BULB ASSEMBLY, Primer (Yellow Washer)	13330K07
3	BULB ASSEMBLY, Primer (Yellow Washer)	13330Q07
4	CHECK VALVE ASSEMBLY, Inlet	21-13331A3
5	CHECK VALVE ASSEMBLY, Outlet	21-13331A4
6	CLAMP, Nylon, Large	54-4158210
7	CLAMP, Nylon, Small	54-41582Q7
8	CLAMP, Nylon, Small	54-41582Q7
8	CLAMP, Worm Gear	54-815504104	54-54428, 54-809952104, 54-8M2001484, 54-F9005, F24772, F24788, F901788

Fuel Management

Below is the parts list for Mercury 250 (3.0L EFI) Fuel Management:

Position No.	Part Name	OEM Number	Supersedes
-	MANAGEMENT ASSEMBLY, Fuel	880004T08	880004T07
1	ADAPTOR PLATE	883951T1
2	GASKET	27-804680
3	REED BLOCK	828623T4
4	SCREW, (M6)	10-8555252
5	BUSHING	23-855364
6	GROMMET	25-855362001	25-855362
7	SCREW, (M8 x 35)	10-81893435
8	WASHER, (.344 x 1.00 x .063) Stainless Steel	12-817274	12-817274 1
9	SCREW, (M8 x 30)	10-81893430
10	PLENUM KIT, Air	883950T1
11	GASKET	27-804679004	27-804679 3
12	SCREW, (M6 x 16)	10-1993716
13	BRACKET, MAP Sensor	884522	804873, 841095
14	SENSOR, MAP	854445
15	SENSOR ASSEMBLY	8M0148668
16	O-RING, (1.78 mm x .08 mm)	25-896699	25-888814
17	THROTTLE BODY KIT	883949T1
18	SCREW, (M6 x 40)	10-82130040
19	O-RING	25-855426
20	LEVER ASSEMBLY, Throttle	858851A03
21	ROLLER	8M0072162	889610, 840968
22	WASHER, (.203 x .500 x .032)	12-8M0204666
23	NUT, Stainless Steel	8-32,11-826709104	11-846115
24	SCREW, Special	10-889354
25	WASHER, Cupped	12-881991
26	WASHER, Spool	12-881992
27	LOCKWASHER, External	10,13-69432
28	CAM ASSEMBLY	858353A08	858353A 3
29	BALL, Threaded	8235694
30	BUSHING	23-8M0215006
31	BUSHING	23-8807371
32	SCREW, (M8 x 55) Stainless Steel	10-40011155
33	WASHER, (.330 x .750 x .060) Stainless Steel	12-56720
34	FITTING	22-993211
35	PUMP ASSEMBLY, Oil	8M0185615
36	BRACKET	883926
37	SCREW, (M4 x 16)	10-883942
38	SCREW, (M6 x 25)	10-82130025
39	WASHER	12-8M0214930
40	GROMMET	25-8M0190980
41	BUSHING	23-822003
42	FUEL RAIL	883952T1
43	RETAINER	8833821
44	SCREW, (#8-32 x .380)	10-840118
45	INJECTOR ASSEMBLY	840481T01	840481001, 840481, 883381
46	O-RING KIT	25-895239A01
47	TUBE	8832151
48	O-RING	25-883355
49	FITTING	22-883940
50	SCREW, (#10-24 x .375)	10-883376
51	RETAINER	883382
52	O-RING, (.239 x .070)	25-20385
53	HARNESS ASSEMBLY, Fuel Rail	84-880745T1
54	CLAMP	54-883941
55	J CLIP (Use where Applicable)	54-8M0024808
56	SCREW, (M6 x 40)	10-82130040
-	GASKET SET, Powerhead	27-832934A00
-	POWERHEAD ASSEMBLY Comment: (200)	891823A07	891823A04, 891823B04 (200)
-	POWERHEAD ASSEMBLY Comment: (225)	883892A07	883892A04, 883892A03, 883892A02 (225)
-	POWERHEAD ASSEMBLY Comment: (250)	883894A07	883894A04, 883894A03, 883894A02 (250)

Fuel Pump

Below is the parts list for Mercury 250 (3.0L EFI) Fuel Pump:

Position No.	Part Name	OEM Number	Supersedes
-	PUMP KIT, Fuel	14360A78
1	NOT SOLD SEPARATE, Fuel Pump	NSS
-	DIAPHRAGM KIT	21-857005A1
2	NOT SOLD SEPARATE, Disc Check Valve	NSS
3	NOT SOLD SEPARATE, Diaphragm	NSS
4	NOT SOLD SEPARATE, Retainer	NSS
5	NOT SOLD SEPARATE, Spring	NSS
6	NOT SOLD SEPARATE, Cap	NSS
7	NOT SOLD SEPARATE, Spring	NSS
8	NOT SOLD SEPARATE, Cap	NSS
9	NOT SOLD SEPARATE, Diaphragm	NSS
10	NOT SOLD SEPARATE, Gasket-Boost	NSS
11	NOT SOLD SEPARATE, Gasket-Pulse	NSS
12	GASKET	27-8M0204705
13	PLATE	987752
14	FITTING, Straight (.125-27)	22-16604
15	SCREW, (M5 x 40), Fuel Pump	10-82104540
16	SCREW, (M6 x 50), Pump to Crankcase	10-82130050
17	BASE	144303
18	ELBOW, To Crankcase	22-856842
19	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
20	HOSE, Pulse Line	32-8M0064783	32-858800
21	CONNECTOR	22-822769
22	HOSE	32-8M0064778	32-856817 2
23	NOT SOLD SEPARATE, Cap	NSS
24	HOSE/SLEEVE	32-8M0064780	32-856818A 1
25	HOSE, (57.00 Inches Bulk) (Cut to 16 Inches)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
26	CONNECTOR	22-858955
27	CLAMP, Hose (15.3)	54-8M0214964
28	HOSE	32-8839461
29	HOSE, (40.00 Inches Bulk) (Cut to 15 Inches) To Elbow on Plenum	32-8M0054213	32-855834 66
30	HOSE, (40.00 Inches Bulk) (Cut to 28 Inches) To Oil Pump	32-8M0054213	32-855834 66
31	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
32	CONDUIT	32-883965
-	GASKET SET, Powerhead	27-832934A00
-	POWERHEAD ASSEMBLY Comment: (200)	891823A07	891823A04, 891823B04 (200)
-	POWERHEAD ASSEMBLY Comment: (225)	883892A07	883892A04, 883892A03, 883892A02 (225)
-	POWERHEAD ASSEMBLY Comment: (250)	883894A07	883894A04, 883894A03, 883894A02 (250)

Gear Housing, Driveshaft-Standard/Counter Rotation

Below is the parts list for Mercury 250 (3.0L EFI) Gear Housing, Driveshaft-Standard/Counter Rotation:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Complete - Standard - Long	1600-880686A43	1600-880686T29
-	GEAR HOUSING ASSEMBLY, Complete - Standard - X Long	1600-880686A44	1600-880686T33
-	GEAR HOUSING ASSEMBLY, Complete - Standard - XX Long	1600-880686A51	1600-880686T34
-	GEAR HOUSING ASSEMBLY, Complete - Counter Rotation - X Long	1600-880686A52	1600-880686T38
-	GEAR HOUSING ASSEMBLY, Complete - Counter Rotation - XX Long	1600-880686A53	1600-880686T39
1	GEAR HOUSING ASSEMBLY, Basic, Used With 5/16 Inch Shift Crank Comment: SN# 1B853027 & Below	1600-880687T01
1	GEAR HOUSING ASSEMBLY, Basic, Used With 1/4 Inch Shift Crank Comment: SN# 1B853028 & Up	1600-8M0056631
2	FILLER BLOCK Comment: SN# 1B537639 & Below	821526001	821526 SN# 1B537639 & Below
2	FILLER BLOCK Comment: SN# 1B537640 & Up	8M0010459
3	PIN, Dowel - Without Hole (.375 x .625)	17-43044
4	ANODE	97-826134Q	826134, 826134A 1
5	SCREW, (M6 x 40)	10-4000333
6	NUT, (M6) Stainless Steel	11-401386
7	PLUG ASSEMBLY, (.375-16 x .250)	10-79953A04
8	SEAL	26-8M0204693
9	ANODE KIT Comment: Mercury	97-76214T5
9	ANODE KIT Comment: Quicksilver	97-76214Q5
10	SCREW, (.437-14 x 1.750)	10-8M0204686
11	COVER ASSEMBLY Comment: Design-I	8M0047129	880703A 1 Design-I
11	COVER ASSEMBLY Comment: Design-II	8M0047129	880703A 1 Design-II
12	FITTING Comment: Design-I and II	22-881866	22-859432 Design-I and II
13	O-RING, (799 x .103) Comment: Design-I and II	25-896522
14	SEAL, Oil Comment: Design-I and II	26-8M0204708
15	RETAINING RING Comment: Design-II	53-8M0046563
16	SCREW, (M6 x 20) Stainless Steel	10-8M0204741
17	WASHER	12-77674
18	GASKET	27-880729
19	SHIFT SHAFT	824145
20	NOT SOLD SEPARATE, Pinion Gear Comment: Part of 43-892595A04 or 43-880720A03	NSS
21	NUT, (.625-18)	11-35921
22	WASHER	12-92721
23	BEARING ASSEMBLY, Roller	31-42647A1
24	DRIVESHAFT, Long	45-895079T
24	DRIVESHAFT, X-Long	45-895080T
24	DRIVESHAFT, XX-Long	45-895081T
25	KEY, Also a Component of Water Pump Housing	28-8M0204723
26	SHIM/BEARING ASSEMBLY Comment: SN# 1B792549 & Below	15-884327A02
27	SHIM ASSEMBLY	15-8M0063268
28	NOT SOLD SEPARATE, Roller Bearing Assembly Comment: SN# 1B792549 & Below	NSS
29	NOT SOLD SEPARATE, Cup Comment: SN# 1B792549 & Below	NSS
30	NOT SOLD SEPARATE, Roller Bearing Assembly Comment: SN# 1B792549 & Below	NSS
31	NOT SOLD SEPARATE, Cup Comment: SN# 1B792549 & Below	NSS
32	RETAINER	8245191
33	HOUSING, Water Pump-Complete	817275A09
34	SEAL KIT	26-861415A1
35	SCREW, (M6 x 20) Stainless Steel	10-8M0204741
36	IMPELLER	47-43026T2
37	FACEPLATE	8M0204709
38	RING, Retaining	53-880719
39	CARRIER ASSEMBLY, Oil Seal	8M0007131	888909A 1
40	O-RING, (2.175 x .103)	25-8M0142854
41	NOT SOLD SEPARATE, Oil Seal	NSS
42	NOT SOLD SEPARATE, Oil Seal	NSS
43	GASKET	27-8172771
44	GASKET	27-430331
45	COUPLING ASSEMBLY	832942A1
46	O-RING, (1.046)	25-8M0204654
47	O-RING, (.796 x .139)	25-8M0204645
48	COUPLING	43585
49	BEARING ASSEMBLY, Roller/Cup Comment: SN# 1B792550 & Up	31-8M0146566
50	NOT SOLD SEPARATE, CUP Comment: SN# 1B792550 & Up	NSS
51	SHIM SET Comment: SN# 1B792550 & Up	15-8M0053110
52	BEARING, Tapered Roller Comment: SN# 1B792550 & Up	31-8M0146553
53	NOT SOLD SEPARATE, CUP Comment: SN# 1B792550 & Up	NSS
-	SEAL KIT, Gear Housing	26-830749A01
-	REPAIR KIT, Water Pump-Upper	817275A08

Gear Housing, Prop Shaft - Std Rotation 2B014225 & below

Below is the parts list for Mercury 250 (3.0L EFI) Gear Housing, Prop Shaft - Std Rotation 2B014225 & below:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Complete - Standard - Long	1600-880686A43	1600-880686T29
-	GEAR HOUSING ASSEMBLY, Complete - Standard - X Long	1600-880686A44	1600-880686T33
-	GEAR HOUSING ASSEMBLY, Complete - Standard - XX Long	1600-880686A51	1600-880686T34
1	GEAR HOUSING ASSEMBLY, Basic, Used With 5/16 Inch Shift Crank Comment: SN# 1B853027 & Below	1600-880687T01
1	GEAR HOUSING ASSEMBLY, Basic, Used With 1/4 Inch Shift Crank Comment: SN# 1B853028 & Up	1600-8M0056631
2	NOT SOLD SEPARATE, Plug	NSS
3	CRANK, Shifter, 5/16 Pivot Pin Comment: SN# 1B853027 & Below	896847A01	892075 SN# 1B853027 & Below
3	CRANK, Shifter, 1/4 Pivot Pin Comment: SN# 1B853028 & Up	8M0220880
4	SPOOL ASSEMBLY	8M0235940
5	NOT SOLD SEPARATE, Spool	NSS
6	COTTER PIN	18-469501
7	NOT SOLD SEPARATE, Sleeve Adjusting	NSS
8	GEAR SET, Forward/Pinion	43-892595A04
9	SHIM SET	15-884328A01
10	BEARING ASSEMBLY, Roller	31-8M0142836
11	NOT SOLD SEPARATE, Cup	NSS
12	RING, Retaining	53-8M0051043	53-23721
13	THRUST WASHER	12-8M0053823	12-892805
14	BEARING ASSEMBLY, Roller-Tappered	31-8M0142835
15	NOT SOLD SEPARATE, Cup	NSS
16	CLUTCH	52-880714T01
17	SPRING	24-30893
18	PIN, Detent	17-828356
19	PROPELLER SHAFT	44-888530
20	PIN, Cross	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
21	GEAR, Reverse	43-8M0118363
22	THRUST RING	880699
23	SPACER, Thrust	23-891919001
24	CARRIER ASSEMBLY, Bearing	880696A08
25	SHIM SET	15-891936A01
26	BEARING, Ball	30-8M0142873
27	SEAL, Oil	26-8M0204700
28	BEARING ASSEMBLY, Tapered	31-8M0148319
29	NOT SOLD SEPARATE, Cup	NSS
30	SEAL, Oil	26-8M0204700
31	O-RING, (3.850 x .210)	25-8M0142840
32	SCREW/SEAL KIT	10-880717A01
33	SEAL	26-8M0204693
34	KEYED WASHER	14-880697
35	RETAINER	8M2011027	79448
-	SEAL KIT, Gear Housing	26-830749A01

Gear Housing, Prop Shaft - Std Rotation 2B014226 & up

Below is the parts list for Mercury 250 (3.0L EFI) Gear Housing, Prop Shaft - Std Rotation 2B014226 & up:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Complete - Standard - Long	1600-880686A43	1600-880686T29
-	GEAR HOUSING ASSEMBLY, Complete - Standard - X Long	1600-880686A44	1600-880686T33
-	GEAR HOUSING ASSEMBLY, Complete - Standard - XX Long	1600-880686A51	1600-880686T34
1	GEAR HOUSING ASSEMBLY, Basic, Used With 1/4 Inch Shift Crank Comment: SN# 1B853028 & Up	1600-8M0056631
2	NOT SOLD SEPARATE, Plug	NSS
3	CRANK, Shifter, 1/4 Pivot Pin Comment: SN# 1B853028 & Up	8M0220880
4	SPOOL ASSEMBLY	8M0235940
5	NOT SOLD SEPARATE, Spool	NSS
6	COTTER PIN	18-469501
7	NOT SOLD SEPARATE, Sleeve Adjusting	NSS
8	GEAR SET, Forward/Pinion	43-892595A04
9	SHIM SET	15-884328A01
10	BEARING ASSEMBLY, Roller	31-8M0142836
11	NOT SOLD SEPARATE, Cup	NSS
12	RING, Retaining	53-8M0051043	53-23721
13	THRUST WASHER	12-8M0053823	12-892805
14	BEARING ASSEMBLY, Roller-Tappered	31-8M0142835
15	NOT SOLD SEPARATE, Cup	NSS
16	CLUTCH	52-880714T01
17	SPRING	24-30893
18	PIN, Detent	17-828356
19	PROPELLER SHAFT	44-8M0140446
20	PIN, Cross	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
21	GEAR, Reverse	43-8M0118363
22	THRUST RING	880699
23	SPACER	23-8M0064306
24	SHIM SET	15-8M0076745
24	WASHER, .020	12-8M0050423
24	WASHER, .022	12-8M0050424
24	WASHER, .024	12-8M0050425
24	WASHER, .026	12-8M0050427
24	WASHER, .028	12-8M0050428
24	WASHER, .030	12-8M0050429
24	WASHER, .032	12-8M0050430
24	WASHER, .034	12-8M0050431
24	WASHER, .036	12-8M0050432
24	WASHER, .038	12-8M0050433
24	WASHER, .040	12-8M0050434
24	WASHER, .042	12-8M0050435
24	WASHER, .044	12-8M0050436
24	WASHER, .046	12-8M0050437
24	WASHER, .048	12-8M0050438
24	WASHER, .050	12-8M0050439
25	CARRIER ASSEMBLY, Bearing	8M0083392
26	BEARING, Ball	30-8M0142873
27	SEAL, Oil	26-8M0204700
28	BEARING ASSEMBLY, Tapered	31-8M0148319
29	NOT SOLD SEPARATE, Cup	NSS
30	SEAL, Oil	26-8M0204700
31	O-RING, (3.850 x .210)	25-8M0142840
32	SCREW/SEAL KIT	10-880717A01
33	SEAL	26-8M0204693
34	KEYED WASHER	14-880697
35	RETAINER	8M2011027	79448
-	SEAL KIT, Gear Housing	26-830749A01

Gear Housing, Prop Shaft-Counter Rotation 2B014225 & below

Below is the parts list for Mercury 250 (3.0L EFI) Gear Housing, Prop Shaft-Counter Rotation 2B014225 & below:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Complete - Counter Rotation - X Long	1600-880686A52	1600-880686T38
-	GEAR HOUSING ASSEMBLY, Complete - Counter Rotation - XX Long	1600-880686A53	1600-880686T39
1	GEAR HOUSING ASSEMBLY, Basic, Used With 5/16 Inch Shift Crank Comment: SN# 1B853027 & Below	1600-880687T01
1	GEAR HOUSING ASSEMBLY, Basic, Used With 1/4 Inch Shift Crank Comment: SN# 1B853028 & Up	1600-8M0056631
2	NOT SOLD SEPARATE, Plug	NSS
3	CRANK, Shifter, 5/16 Pivot Pin Comment: SN# 1B853027 & Below	896847A01	892075 SN# 1B853027 & Below
3	CRANK, Shifter, 1/4 Pivot Pin Comment: SN# 1B853028 & Up	8M0220880
4	SPOOL ASSEMBLY	8M0235940
5	NOT SOLD SEPARATE, Spool	NSS
6	COTTER PIN	18-469501
7	NOT SOLD SEPARATE, Sleeve Adjusting	NSS
8	GEAR, Reverse	43-880723A02
9	BEARING ASSEMBLY, Roller	31-8M0142836
10	NOT SOLD SEPARATE, Cup	NSS
11	RING, Retaining	53-8M0051043	53-23721
12	THRUST WASHER	12-8M0053823	12-892805
13	BEARING ASSEMBLY, Roller-Tappered	31-8M0142835
14	NOT SOLD SEPARATE, Cup	NSS
15	SHIM SET	15-884328A01
16	SPRING	24-30893
17	CLUTCH	52-880714T01
18	PIN, Cross	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
19	PIN, Detent	17-828356
20	PROPELLER SHAFT	44-888530
21	GEAR KIT, Forward/Pinion	43-8M0119539	43-880720A03
22	THRUST RING	880699
23	BEARING, Thrust	31-815480
24	CARRIER ASSEMBLY, Bearing	880696A10
25	O-RING, (3.850 x .210)	25-8M0142840
26	BEARING ASSEMBLY, Needle Rollers	31-814653T	31-814653, 31-814653001
27	ADAPTOR, Bearing	8M0148384
28	SHIM SET	15-47397A1
29	SHIM SET	15-891936A01
30	BEARING ASSEMBLY, Tapered	31-8M0148319
31	NOT SOLD SEPARATE, Cup	NSS
32	SEAL, Oil	26-8M0204700
33	SEAL, Oil	26-8M0204700
34	SCREW/SEAL KIT	10-880717A01
35	SEAL	26-8M0204693
36	ADAPTOR	8M0053183	892818
37	SPACER, Thrust	23-891919001
38	KEYED WASHER	14-880697
39	RETAINER	8M2011027	79448
40	NOT SOLD SEPARATE, Decal-Counter Rotation	NSS
-	SEAL KIT, Gear Housing	26-830749A01

Gear Housing, Prop Shaft-Counter Rotation 2B014226 & up

Below is the parts list for Mercury 250 (3.0L EFI) Gear Housing, Prop Shaft-Counter Rotation 2B014226 & up:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Complete - Counter Rotation - X Long	1600-880686A52	1600-880686T38
-	GEAR HOUSING ASSEMBLY, Complete - Counter Rotation - XX Long	1600-880686A53	1600-880686T39
1	GEAR HOUSING ASSEMBLY, Basic, Used With 5/16 Inch Shift Crank Comment: SN# 1B853027 & Below	1600-880687T01
1	GEAR HOUSING ASSEMBLY, Basic, Used With 1/4 Inch Shift Crank Comment: SN# 1B853028 & Up	1600-8M0056631
2	NOT SOLD SEPARATE, Plug	NSS
3	CRANK, Shifter, 5/16 Pivot Pin Comment: SN# 1B853027 & Below	896847A01	892075 SN# 1B853027 & Below
3	CRANK, Shifter, 1/4 Pivot Pin Comment: SN# 1B853028 & Up	8M0220880
4	SPOOL ASSEMBLY	8M0235940
5	NOT SOLD SEPARATE, Spool	NSS
6	COTTER PIN	18-469501
7	NOT SOLD SEPARATE, Sleeve Adjusting	NSS
8	GEAR, Reverse	43-880723A02
9	BEARING ASSEMBLY, Roller	31-8M0142836
10	NOT SOLD SEPARATE, Cup	NSS
11	RING, Retaining	53-8M0051043	53-23721
12	THRUST WASHER	12-8M0053823	12-892805
13	BEARING ASSEMBLY, Roller-Tappered	31-8M0142835
14	NOT SOLD SEPARATE, Cup	NSS
15	SHIM SET	15-884328A01
16	SPRING	24-30893
17	CLUTCH	52-880714T01
18	PIN, Cross	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
19	PIN, Detent	17-828356
20	PROPELLER SHAFT	44-8M0140446
21	GEAR KIT, Forward/Pinion	43-8M0119539	43-880720A03
22	THRUST RING	880699
23	BEARING, Thrust	31-815480
24	SHIM SET	15-8M0076745
24	WASHER, .020	12-8M0050423
24	WASHER, .022	12-8M0050424
24	WASHER, .024	12-8M0050425
24	WASHER, .026	12-8M0050427
24	WASHER, .028	12-8M0050428
24	WASHER, .030	12-8M0050429
24	WASHER, .032	12-8M0050430
24	WASHER, .034	12-8M0050431
24	WASHER, .036	12-8M0050432
24	WASHER, .038	12-8M0050433
24	WASHER, .040	12-8M0050434
24	WASHER, .042	12-8M0050435
24	WASHER, .044	12-8M0050436
24	WASHER, .046	12-8M0050437
24	WASHER, .048	12-8M0050438
24	WASHER, .050	12-8M0050439
25	CARRIER ASSEMBLY, Bearing	8M0083392
26	O-RING, (3.850 x .210)	25-8M0142840
27	BEARING ASSEMBLY, Needle Rollers	31-814653T	31-814653, 31-814653001
28	ADAPTOR, Bearing	8M0148384
29	SHIM SET	15-47397A1
30	BEARING ASSEMBLY, Tapered	31-8M0148319
31	NOT SOLD SEPARATE, Cup	NSS
32	SEAL, Oil	26-8M0204700
33	SEAL, Oil	26-8M0204700
34	SCREW/SEAL KIT	10-880717A01
35	SEAL	26-8M0204693
36	ADAPTOR	8M0053183	892818
37	SPACER	23-8M0064306
38	KEYED WASHER	14-880697
39	RETAINER	8M2011027	79448
40	NOT SOLD SEPARATE, Decal-Counter Rotation	NSS
-	SEAL KIT, Gear Housing	26-830749A01

Mercathode Kit

Below is the parts list for Mercury 250 (3.0L EFI) Mercathode Kit:

Position No.	Part Name	OEM Number
1	MERCATHODE KIT	88334A2
2	MERCATHODE ASSEMBLY	88334A4
3	SCREW, (#9-14 x .875)	10-22793
4	WASHER, (.192 x .375 x .0312) Stainless Steel	12-30164
5	NUT, Brass	10-32,11-45076
6	ELECTRODE ASSEMBLY	72958A5
7	O-RING, (.796 x .139)	25-8M0204645
8	SCREW, (#10-16 x 1.250) Stainless Steel	10-87698
9	ANODE ASSEMBLY	97-72957A5
10	O-RING, (.796 x .139)	25-8M0204645
11	SCREW, (#10-16 x 1.250) Stainless Steel	10-87698
12	FUSE, 20 Ampere	88-8M0207796
13	CABLE ASSEMBLY, (5.00 Inches) Red	84-95084A10
14	CABLE ASSEMBLY, (64.00 Inches)	84-95084A13
15	CABLE ASSEMBLY, (72.00 Inches) Black	84-79138A8

Oil Injection Components

Below is the parts list for Mercury 250 (3.0L EFI) Oil Injection Components:

Position No.	Part Name	OEM Number	Supersedes
1	TANK ASSEMBLY, Oil	1200-8M0119508	1200-8M0064073, 1270-830889A10, 1270-830889A 4
2	NOT SOLD SEPARATE, Decal-Reservoir	NSS
3	SCREW, (.164-18 x .375)	10-58376
4	WASHER, (.203 x .562 x .060) Stainless Steel	12-72761
5	CAP ASSEMBLY	36-814449A3
6	GASKET	27-42999T
7	SWITCH ASSEMBLY	87-856156T02	87-856156A 2
8	SCREW, (M8 x 35)	10-81893435
9	WASHER	12-4002318
10	GROMMET	25-855362001	25-855362
11	BUSHING	23-855364
12	HOSE, (57.00 Inches Bulk) (Cut to 7 Inches)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
13	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
14	FITTING	22-8M0207780
15	HOSE, (2.00 Inches)	32-875283
16	FILTER, Oil - In Line	35-875284T01	35-875284001, 35-875284
17	HOSE	32-875289
18	CONNECTOR	22-858955
19	NOT SOLD SEPARATE, Plug	NSS
20	HOSE, (24.00 Inches Braided) (Cut to 22 Inches)	32-892830053

Port Bleed System

Below is the parts list for Mercury 250 (3.0L EFI) Port Bleed System:

Position No.	Part Name	OEM Number	Supersedes
1	CHECK VALVE	21-8282182
2	PIPE PLUG	22-8272011
3	TUBING, (38.00 Inches Bulk) (Cut to 20-1/2 Inches)	32-8M0054152	32-856060 65
4	CHECK VALVE	21-8159234
5	CHECK VALVE, 90 Degree (.0625-27)	21-8592352
6	TUBING, (38.00 Inches Bulk) (Cut to 13 Inches)	32-8M0054152	32-856060 65
7	CHECK VALVE	21-426585
8	PIPE PLUG	22-8272011
9	CLIP	54-23567
10	SCREW, (#10-16 x .500)	10-878608	10-812832
11	TUBING, (38.00 Inches Bulk) (Cut to 11 Inches)	32-8M0054152	32-856060 65
12	TUBING, (240.00 Inches Bulk) (Cut to 22-1/2 Inches)	32-892024122	32-99130122
13	SCREW, (M8 x 14)	10-81893414
14	CLAMP	54-859172
15	WASHER	12-36001
-	POWERHEAD ASSEMBLY Comment: (200)	891823A07	891823A04, 891823B04 (200)
-	POWERHEAD ASSEMBLY Comment: (225)	883892A07	883892A04, 883892A03, 883892A02 (225)
-	POWERHEAD ASSEMBLY Comment: (250)	883894A07	883894A04, 883894A03, 883894A02 (250)

Power Trim Components

Below is the parts list for Mercury 250 (3.0L EFI) Power Trim Components:

Position No.	Part Name	OEM Number	Supersedes
-	POWER TRIM KIT	855998A11	855998A08, 855998A07, 855998A10, 855998A09, 855998A05, 855998A 3
1	TRIM MOTOR	8M0031551
2	NOT SOLD SEPARATE, Armature	NSS
3	NOT SOLD SEPARATE, End Frame	NSS
-	O-RING	25-878285
4	SCREW, (M6 x 30)	10-82494830
5	LOCKWASHER, (M6)	13-400256
6	DRIVESHAFT	8782451
7	PO CHECK KIT	878410A1
8	VALVE KIT, Relief, Includes Reference #26	893929A01	813442A 2
9	SHAFT KIT, Tilt Pivot	8M0142997
10	PIN	17-878267	17-44431
11	CYLINDER KIT, Tilt	878235A03	878235A02, 878235A 1
12	END CAP KIT, Tilt Cylinder, Includes Reference #26	878239A02	878239A 1
13	O-RING KIT, Includes Reference #26	8M0142999
14	SHOCK ROD KIT, Includes Reference #26	8M0168219
15	PISTON ASSEMBLY, Memory	8M0143000
16	REPAIR KIT, Check Valve, Includes Reference #26	878406A02	878406A 1
17	PISTON ASSEMBLY	878414T01	878414A 1
18	PISTON ASSEMBLY	878413A1
19	END CAP ASSEMBLY	1100-8M0021648	878243A 1
20	RESERVOIR KIT	878264A1
21	PLUG ASSEMBLY	19-811613
22	SCREW, (M6 x 14)	10-4000327
23	WASHER	12-4002315
24	PUMP KIT	892251A01	878411A 1
25	REPAIR KIT, Power Trim	878408A1
26	PIN, Trilobe	17-821539	17-13794, 17-19603
27	SCREW, (M10 x 30)	10-858771
28	WASHER	12-4002319
29	ANODE KIT	97-818298Q1
30	SCREW, (M6 x 25)	10-8M0204707
31	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
32	SHAFT	99625002
33	C WASHER	8M0084613	69205
34	CLAMP	54-26550
35	SCREW, (#10-16 x .600)	10-878609	10-812832 1
36	CONDUIT, (.350 Inside Diameter x 3.00 Feet Bulk), Cut to 12 Inches	32-828547353
37	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275

Powerhead Gasket Set Components

Below is the parts list for Mercury 250 (3.0L EFI) Powerhead Gasket Set Components:

Position No.	Part Name	OEM Number	Supersedes
-	GASKET SET, Powerhead	27-832934A00
0	DIAPHRAGM KIT, Fuel Pump	21-857005A1
0	NOT SOLD SEPARATE, Diaphragm	NSS
0	NOT SOLD SEPARATE, Retainer	NSS
0	NOT SOLD SEPARATE, Spring	NSS
0	NOT SOLD SEPARATE, Cap	NSS
0	NOT SOLD SEPARATE, Spring	NSS
0	NOT SOLD SEPARATE, Cap-Spring End	NSS
0	NOT SOLD SEPARATE, Gasket-Boost	NSS
0	NOT SOLD SEPARATE, Gasket-Pulse	NSS
0	GASKET, Fuel Pump	27-8M0204705
0	GASKET, Fuel Management Adaptor Plate	27-804680
0	O-RING, (3.237 x .103), Lower End Cap	25-62700
0	SEAL, Cylinder Head	818574
0	GASKET, Thermostat Cover	27-8503181
0	O-RING, (.859 x .139), Crankshaft-Lower	25-35126
0	O-RING, (1.989 x .070), Crankshaft-Upper	25-823683	25-64067
0	GASKET, Cylinder Block	27-8329335
0	GASKET, Exhaust Plate	27-8329344
0	GASKET, Relief Valve Cover and Plate	27-88907003
0	SEAL, Thermostat Comment: Not used for this application	26-854639001	26-854639 Not used for this application

Reservoir Kit-Remote Oil(15943A1)

Below is the parts list for Mercury 250 (3.0L EFI) Reservoir Kit-Remote Oil(15943A1):

Position No.	Part Name	OEM Number	Supersedes
-	RESERVOIR KIT, Oil	15943A1
1	TANK ASSEMBLY, Oil (1.8 Gallon Tank)	15943A2
2	NOT SOLD SEPARATE, BRACKET, Tank Mount Comment: (Also sold with Bracket Kit Below)	NSS
3	NOT SOLD SEPARATE, HANDLE/ROPE	NSS
-	BRACKET KIT, Oil Reservoir Hold Down Comment: (Includes ref. 2)	824954A1
4	CORD/HOOK KIT	12323A1
5	BRACKET, Hold Down	12320
6	SCREW, (#12-11 x .750)	10-79968
7	CAP ASSEMBLY, Oil Reservoir	36-43298A2
8	NOT SOLD SEPARATE, CORD	NSS
9	O-RING, (2.225 x .210), Cap	25-11332
10	HOUSING ASSEMBLY, Adapter	816190A4
11	CAP ASSEMBLY, Housing Adaptor	36-43298A2
12	O-RING, (2.225 x .210)	25-11332
13	TUBE, Oil Pick Up	32-99802
14	HOSE, (114.00 Inches)	32-99439
15	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275

Service/Support Material

Below is the parts list for Mercury 250 (3.0L EFI) Service/Support Material:

Position No.	Part Name	OEM Number	Supersedes
-	PARTS MANUAL, 200/225/250 (3.0L) EFI	90-803199008
-	SERVICE MANUAL	90-884294R01	90-884294
-	OPERATION MANUAL, 225/250 GEN II, English	90-10128081
-	OWNERS MANUAL, 225/250 EFI 2-Stroke, Spanish	90-10128J70
-	OWNERS MANUAL, 225/250 EFI 2-Stroke, French	90-10128D70
-	DECAL SET, 225/250 Comment: (2B111193 and up)	37-8M0094904
-	DECAL, EPA Label Information Comment: (200)	37-891764A06
-	DECAL, EPA Label Information Comment: (225/250)	37-804670A06

Shift Linkage

Below is the parts list for Mercury 250 (3.0L EFI) Shift Linkage:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET ASSEMBLY, Anchor	899080T01
2	LATCH	824016
3	DRIVE SCREW	10-42975
4	CUP, Barrel Retainer	824015
5	SWITCH	87-8M0207794
6	SCREW, (M3.5 x 20)	10-82470620
7	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
8	SHIFT RAIL	8M0033943	899081
9	SCREW, (M8 x 25 MM)	8M0006893
10	SHIFT SHAFT, Upper Comment: Long	8M0026171	899084001 Long
10	SHIFT SHAFT, Upper Comment: X Long	8M0026172	899084002 X Long
10	SHIFT SHAFT, Upper Comment: XX Long	8M0188525
11	BUSHING	23-892263
12	NUT, (M6) Stainless Steel	11-401386
13	WASHER, (.255 x .620 x .030) Stainless Steel	12-69056
14	LINK, Shift	899083
15	SLIDE, Shift	8M0085621	899082
16	PIN, Shift Link	8M0000793
17	BUSHING	23-896551
18	WASHER, (.255 x .620 x .030) Stainless Steel	12-69056
19	NUT, (M6) Stainless Steel	11-401386
20	PIN, Bow Tie Clip	8M0001157

Solenoid Plate

Below is the parts list for Mercury 250 (3.0L EFI) Solenoid Plate:

Position No.	Part Name	OEM Number	Supersedes
-	NOT SOLD SEPARATE, Electrical Plate Assembly-Complete	NSS
1	PLATE	858366T2
2	SOLENOID ASSEMBLY, (#10-32 / .3125-18 Terminals)	89-817109A2
3	GROMMET	25-822179
4	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
5	SCREW, (M6 x 25 MM)	10-82129125
6	BUSHING	23-8M0214955
7	RELAY ASSEMBLY	8M0207773
8	NOT SOLD SEPARATE, Decal-Trim Relay	NSS
9	BRACKET	828102
10	BUSHING	23-8M0214955
11	GROMMET	25-818967
12	SCREW, (M6 x 10)	10-82129110
13	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
14	CLIP	54-828991T	54-828991
15	CLIP, (1.00)	54-858755
16	HARNESS ASSEMBLY, Fuse - 100 Ampere	84-878231A6
17	HARNESS ASSEMBLY, Trim	84-819514T21	84-819514A21
18	HARNESS ASSEMBLY, Engine	84-892973T01
19	FUSE, Mini - Yellow - 20 Ampere Comment: (20 AMP)	88-832969T20	88-832969 20 (20 AMP)
19	FUSE, Mini - Tan - 5 Ampere Comment: (5 AMP)	88-832969T05	88-832969 5 (5 AMP)
20	COVER, Fuse	858754
-	HARNESS ASSEMBLY (TPS)	879346A41	84-878073A 2
-	HARNESS ASSEMBLY, Encoder, Crank Position Sensor	84-879964A2
-	HARNESS ASSEMBLY, Alternator, Alternator	84-881262A2
21	CABLE ASSEMBLY, Starter	84-882829A1
22	CABLE ASSEMBLY, Battery - Positive	84-88439A46
23	NUT, (.312-18)	11-8M0204668
24	LOCKWASHER, (.312)	13-53166
25	CAP NUT,	10-32,11-813938
26	NUT, Brass	10-32,11-45076
27	CABLE ASSEMBLY, (4.00 Inches) Black	84-88807A16
28	CAP, Female	13540
28	PLUG, Male	13541
29	PCM, Propulsion Control Module Comment: (200)	89790644T	88555741T, 88555741S, 88555729S, 88555721S (200)
29	PCM, Propulsion Control Module Comment: (225)	89790645T	88555742T, 88555742S, 88555727S, 88555711S (225)
29	PCM, Propulsion Control Module Comment: (250)	89790646T	88555743T, 88555743S, 88555735S, 88555728S, 88555712S (250)
30	SCREW, (M6 x 25)	10-82130025
31	WASHER, (.265 x .750 x .048) Stainless Steel	12-65567
32	GROMMET	25-8M0190980
33	BUSHING	23-856954
34	CLIP	54-891520001
35	SCREW, (M6 x 14)	10-82129114
36	BRACKET	892295F01
37	GROMMET	25-8M0190980
38	BUSHING	23-822003
39	SENSOR, Pressure (0 - 100 PSI)	881879T11	881879011, 881879A 6
40	FITTING	22-8M0207782
41	CLIP, (.865)	54-883066
42	CLIP	54-879962
43	SCREW, (M6 x 25)	10-82130025
44	SCREW, (M6 x 12)	10-82130012
45	CABLE ASSEMBLY, Battery - Negative	84-88439A26
46	SCREW, (M8 x 20)	10-81893420
47	HARNESS ASSEMBLY (200/3.0L Work)	84-882815A1
48	CONNECTOR ASSEMBLY, Weather Cap 6 Pin	877613A02
49	CONNECTOR ASSEMBLY, Weather Cap - Male	830796A04

Speedometer/Block Pressure System

Below is the parts list for Mercury 250 (3.0L EFI) Speedometer/Block Pressure System:

Position No.	Part Name	OEM Number	Supersedes
1	FITTING	22-881866	22-859432
2	TUBING, (52.00 Inches Bulk) (Cut to 44 Inches)	32-85978571
3	COUPLER	22-8M0214971
4	PLUG	22-859732
5	FITTING, Adapter	22-8M0214970
6	TUBING, (52.00 Inches Bulk) (Cut to 5 Inches)	32-85978571
7	TEE, Fitting, To Coil Plate Sensor	22-875207
8	TUBING, (72.00 Inches Bulk) (Cut to 52 Inches)	32-85944975

Starboard Bleed System

Below is the parts list for Mercury 250 (3.0L EFI) Starboard Bleed System:

Position No.	Part Name	OEM Number	Supersedes
1	TUBING, (38.00 Inches Bulk) (Cut to 15-1/2 Inches)	32-8M0054152	32-856060 65
2	CHECK VALVE, 90 Degree (.0625-27)	21-8592352
3	TUBING, (38.00 Inches Bulk) (Cut to 16-1/2 Inches)	32-8M0054152	32-856060 65
4	TUBING, (38.00 Inches Bulk) (Cut to 15 Inches)	32-8M0054152	32-856060 65
5	CLIP	54-23567
6	SCREW, (#10-16 x .500)	10-878608	10-812832
7	CHECK VALVE	21-8282182
-	POWERHEAD ASSEMBLY Comment: (200)	891823A07	891823A04, 891823B04 (200)
-	POWERHEAD ASSEMBLY Comment: (225)	883892A07	883892A04, 883892A03, 883892A02 (225)
-	POWERHEAD ASSEMBLY Comment: (250)	883894A07	883894A04, 883894A03, 883894A02 (250)

Starter Motor

Below is the parts list for Mercury 250 (3.0L EFI) Starter Motor:

Position No.	Part Name	OEM Number	Supersedes
1	STARTER MOTOR ASSEMBLY	50-892339T01	50-892339T, 50-853329T
2	NOT SOLD SEPARATE, Thru Bolt	NSS
3	GEAR KIT	43-880805A1
4	SOLENOID KIT	809463A1
5	BRUSH SET	8M0065258
6	SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel	10-69035
7	CABLE ASSEMBLY, (6.00 Inches) Black	84-93388A1
8	DECAL, Warning	37-8272822
9	LOCKWASHER, (M5)	13-400255
10	NUT, (M5) Stainless Steel	11-400211
11	LOCKWASHER, (.312)	13-8M0204647
12	NUT, (M8) Stainless Steel	11-400213
13	COLLAR	23-8M0034918	23-8M0001391, 56703
14	STOP	8M0043276	879845

Swivel Bracket and Steering Arm

Below is the parts list for Mercury 250 (3.0L EFI) Swivel Bracket and Steering Arm:

Position No.	Part Name	OEM Number	Supersedes
1	SWIVEL BRACKET ASSEMBLY, Black	1499-8M0102865	1499-8710T20
2	O-RING	25-8M0214926
3	BUSHING	23-818764	23-67669
4	SPACER	23-816039
5	SEAL, Oil (Lower)	26-87735
6	FITTING, Grease	22-8M0169589
7	BUSHING	23-821207	23-99608
8	THRUST WASHER	12-816432
9	YOKE, Bottom	826364T	826364F 1
10	RING, Retaining	53-67684
11	STRIKER PLATE	8M0045383	99630 1
12	LOCKWASHER, (.375)	13-58643
13	NUT, (.375-24)	11-46335
14	SCREW, (.250-28 x .500)	10-64014
15	NOT SOLD SEPARATE, Decal-Serial Overlaminate	NSS
16	SENDER ASSEMBLY, Trim	8M0074846	821180A 6
17	SCREW, (#10-24 x .750)	10-852368	10-56682
18	LOCKWASHER, Stainless Steel	10,13-26996
19	WASHER, (.203 x .406 x .040)	12-89302
20	SWIVEL PIN ASSEMBLY, Steering Arm - Stainless Steel	17-8M0132731
21	SCREW, (M12 x 190)	10-8M0141069
22	BUMPER	824998001	824998
23	MOUNT, Upper	8163851
24	WASHER	12-8154371
25	WASHER	12-815436
26	NUT, (M12)	11-896963	11-859129, 11-90099
27	CLAMP	8M0036783	813769
28	SCREW, (M8 x 35)	10-81893435
29	LINK ROD ASSEMBLY	92876A12
30	SCREW, (.375-24 x 1.250)	10-849838	10-14000
31	NUT, (.375-24) Stainless Steel	11-8M0204726
31	NUT, (.375-24) Brass	11-8M0204726
32	WASHER, (.390 x .625 x .062) Stainless Steel	12-37828

Throttle Linkage

Below is the parts list for Mercury 250 (3.0L EFI) Throttle Linkage:

Position No.	Part Name	OEM Number	Supersedes
1	LEVER	8M0040987	825268 2
2	SCREW, (M8 x 35)	10-81893435
3	WASHER	12-36042
4	BUSHING	23-821113
5	SCREW, (M6 x 55)	10-40124
6	NUT, (M6) Stainless Steel	11-400212
7	CAP	42942
8	INSERT	42927
9	NUT, (M6) Stainless Steel	11-401386
10	WASHER	12-35459
11	BUSHING	23-8M0215006
12	LINK, To Cam	8583541

Tools

Below is the parts list for Mercury 250 (3.0L EFI) Tools:

Part Name	OEM Number	Supersedes
DIAL INDICATOR TOOL	91-58222A1
HARNESS ASSEMBLY, DDT Adaptor (Electricl/Ignition)	84-822560A5
FLYWHEEL HOLDER TOOL, Teeth Type	91-52344
STAND TOOL, Powerhead	91-827001A1
CABLE ASSEMBLY, DDT (Electricl/Ignition)	84-825003A1
MULTI-METER KIT, DMT 2004 (Electricl/Ignition)	91-892647A01
CAP TOOL, Flywheel Puller	91-24161
SWITCH ASSEMBLY (Electricl/Ignition)	91-52024A1
TESTER, Eight Chamber (Electricl/Ignition)	91-850439T1
GAP TOOL, Single Chamber (Electricl/Ignition)	91-63998A1
TIMING LIGHT (Electricl/Ignition)	91-99379
GAUGE TOOL (Powerhead)	91-29287
SLEEVE (Powerhead)	91-55919
LIFTING EYE (Powerhead)	91-904551
INSTALLATION TOOL, Lock Ring (Powerhead)	91-93004A2
REMOVAL TOOL, Piston Pin Lock Ring (Powerhead)	91-52952T1
MANDREL TOOL, Piston Pin (Powerhead)	91-92973A1
EXPANDER TOOL, Piston Ring (Powerhead)	91-24697
STAND, Powerhead	91-812549T	91-812549
COMPRESSOR TOOL, Piston Ring (3.625) (Powerhead)	91-823237T	91-823237
TORQUE WRENCH, (0-150 lb-in)	91-66274
PULLER PLATE, Universal	91-37241
ALIGNMENT TOOL (Trim/Tilt System)	91-112301
SPANNER WRENCH (Trim/Tilt System)	91-74951
HEAT LAMP (Trim/Tilt System)	91-63209
ROD TOOL, Backlash Indicator Flag (Gear Housing)	91-53459
INDICATOR TOOL, Backlash (Gear Housing)	91-8M0053505	91-78473
DRIVER TOOL, Bearing (Gear Housing)	91-816244
REMOVAL TOOL, Bearing (Gear Housing)	91-816245
MANDREL, Bearing Driver Cup (Gear Housing)	91-31106T
DRIVER TOOL, Bearing Cup (Gear Housing)	91-87120T
TOOL, Preload (Gear Housing)	91-14311A04
PULLER KIT, Bearing (Gear Housing)	91-31229A7
MANDREL (Gear Housing)	91-15755T
DRIVE HEAD TOOL (Gear Housing)	91-36569T
DRIVER ROD TOOL, Needle Bearings (Gear Housing)	91-37323
WRENCH TOOL, Driveshaft Bearing (Gear Housing)	91-36571T
INSTALLER TOOL, Bearing (Gear Housing)	91-38628T
NUT, (.625-18) (Gear Housing)	11-24156
PLATE (Gear Housing)	91-29310
WASHER (Gear Housing)	12-34961
RETAINING TOOL, Bearing (Gear Housing)	91-43506T
WASHER (Gear Housing)	12-54048
INSTALLATION TOOL, Cross Pin (Gear Housing)	91-86642
ADAPTER KIT, Dial Indicator (Gear Housing)	91-83155
HOLDING TOOL, Dial Indicator (Gear Housing)	91-89897
DRIVER CUP (Gear Housing)	91-36577T
ADAPTOR TOOL, Driveshaft (Gear Housing)	91-61077T
HOLDING TOOL, Driveshaft (Gear Housing)	91-56775T
DRIVER CUP (Gear Housing)	91-36577T
ADAPTOR TOOL, Driveshaft (Gear Housing)	91-61077T
HOLDING TOOL, Driveshaft (Gear Housing)	91-56775T
FOWARD GEAR INSTALLATION TOOL (Gear Housing)	91-815850
INSTALLER TOOL, Needle Bearing - Forward Gear (Gear Housing)	91-86943T
NUT TOOL, Gear Housing Cover (Gear Housing)	91-61069T
GUIDE PLATE (Gear Housing)	91-816243
PULLER, Long, Slide Hammer (Gear Housing)	91-816242
MANDREL (Gear Housing)	91-92788T
DRIVER (Gear Housing)	91-33491
DRIVER, Oil Seal (Gear Housing)	91-31108T
DRIVER TOOL, Oil Seal (Gear Housing)	91-817569T	91-817569
TOOL, Pinion Locating (Gear Housing)	91-12349A05
TOOL, Shimming (Gear Housing)	91-56048001
WRENCH TOOL, Pinion Nut (Gear Housing)	91-61067A04
PROPELLER SHAFT (Gear Housing)	44-93003
PULLER BOLT TOOL, Bearing Carrier (Gear Housing)	91-85716
PULLER JAW ASSEMBLY (Gear Housing)	91-46086A1
INSTALLATION TOOL, Bearing Adaptor (Gear Housing)	91-18605A2
PULLER ASSEMBLY, Slide Hammer (Gear Housing)	91-34569A1
GUIDE TOOL, Water Pump Alignment Pins (Gear Housing)	91-821571A1
CLAMP TOOL KIT (Fuel System)	91-803146A04	91-803146A 2
GAUGE KIT, Air/Fuel Pressure (Fuel System)	91-881833A03	91-881833A 2
SEAL KIT, Wire Harness (Electricl)	91-881814A1

Top Cowl

Below is the parts list for Mercury 250 (3.0L EFI) Top Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	TOP COWL ASSEMBLY, Black	100-889246T86
1	TOP COWL ASSEMBLY, Silver	4001-880012T36	4001-880012T 2
2	SCREW, (M6 x 30)	10-82130030
3	SOUND BLANKET KIT	880014A02	880014A 1
4	NOT SOLD SEPARATE, Sound Blanket-Top	NSS
5	NOT SOLD SEPARATE, Sound Blanket-Port	NSS
6	WASHER, (.250 External Star)	13-93702
7	COVER	826639T
8	BRACKET ASSEMBLY, Cowl	8M0010389
9	NOT SOLD SEPARATE, Pin	NSS
10	RING, Retaining	53-8237951
11	ROLLER	8M0207770
12	GROMMET	25-850685T02	850685002, 25-850685 1
13	BRACKET, Front	8M0036792	821249M 2
14	SCREW, (M6 x 20)	10-82130020
15	BUMPER, Latch	815477
16	PIN, Roll	8155381
17	NUT, (M6) Stainless Steel	11-401366
18	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
19	RING, Retaining	53-8237951
20	ROLLER	8M0207770
21	WASHER	12-87161
22	NOT SOLD SEPARATE, Decal-Break-In	NSS
23	NOT SOLD SEPARATE, Decal-Counter Rotation	NSS
-	DECAL SET Comment: (Mercury 200)	37-891822A06
-	DECAL, (200)	37-897516002
-	DECAL, (3.0L)	37-859264017
-	DECAL SET Comment: (Mercury 225)	37-809693A06
-	DECAL, (225)	37-897517002
-	DECAL, (3.0L)	37-859264017
-	DECAL SET Comment: (Mercury 250)	37-891877A06
-	DECAL, (250)	37-897517003
-	DECAL, (3.0L)	37-859264017
-	DECAL SET Comment: (Mariner 225 Long)	37-827438A03	37-827438A02 (Mariner 225 Long)
-	DECAL SET Comment: (Mariner 225 X-Long)	37-883284A03	37-883284A02 (Mariner 225 X-Long)
-	DECAL SET Comment: (Mariner 250)	37-809168A03	37-809168A02 (Mariner 250)

Transom Brackets

Below is the parts list for Mercury 250 (3.0L EFI) Transom Brackets:

Position No.	Part Name	OEM Number	Supersedes
-	TRANSOM BRACKET KIT	3425-828333A09
1	NOT SOLD SEPARATE, Transom Bracket-Starboard	NSS
2	NOT SOLD SEPARATE, Transom Bracket-Port	NSS
3	FITTING, Grease, Port	22-8M0169588
4	TILT TUBE	826125A1
5	NUT, (1.00-14) Nylon Insert	11-826135
6	O-RING, (.612 x .103)	25-45711
7	WASHER	13-88750
8	NUT, (.875-14)	11-826164
9	SCREW, (.500-20 x 4.500)	10-8M0149747
9	SCREW, (.500-20 x 5 Inches)	10-8M0204730
10	WASHER, (.530 x .870 x .105) Stainless Steel	12-8M0204665
11	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
12	NUT, (.500-20)	11-82671117
13	LEVER ASSEMBLY, Tilt Lock	8M0115104	8M0115103, 99629T 2
14	SPRING, Tension	24-830899
15	NYLINER	23-65830
16	SPRING, Compression	24-830900
17	KNOB	99633
18	PIN, Groove	17-99615
19	PIN	17-893709	17-99617
20	DECAL, Warning	37-8M0043059

Vapor Separator Components

Below is the parts list for Mercury 250 (3.0L EFI) Vapor Separator Components:

Position No.	Part Name	OEM Number	Supersedes
1	COVER KIT, Vapor Separator	883245T04	883245T 2
2	FITTING, Straight	22-881740
3	FITTING	22-883249
4	NOT SOLD SEPARATE, Elbow	NSS
5	FITTING KIT	22-885186A1
6	O-RING, (.468 x .078)	25-831985	25-885187
7	FILTER	35-885188	35-823501
8	VALVE	883219
9	O-RING	25-8M0062785	25-883209
10	CAP	883220
11	PLUG	19-883208	19-881830
12	SEAL	26-883248
13	GASKET	27-883252
14	REGULATOR	883257T1
15	O-RING KIT	25-883593A1
16	WASHER	12-883258
17	SCREW, (M5 x .8)	10-883261
18	SCREW, (M5 x .8)	10-883261
19	WIRE ASSEMBLY	84-881831
20	SCREW AND WASHER, (#8-32 x .750)	1395-808612	1399-5132
21	FLOAT KIT	883253A1
22	SHAFT	F10064
23	VALVE/SEAT KIT, Inlet	883247A1
24	SCREW, (M6 x 16)	10-883223
25	FILTER, Fuel-Water Separating	35-18458Q4
26	PROBE	8M0204710
27	BAFFLE	889318002	883260
28	SCREW, (M6 x 16)	10-883223
29	PUMP KIT	881705T1
30	SLEEVE	8M6000589	23-855428
31	BOWL KIT	883256T1
32	SEAL	26-883248
33	PLUG KIT	19-855435A1
34	O-RING	25-8M0062785	25-883209
35	SCREW, (M6 x 8)	10-16955

Download this page as PDF: Click here

For Mercury Owners:

To assist you in maintaining and repairing your marine engines, we hope the following resources may be of use:

Mercury / Mercruiser / Mariner Parts from JLM Marine

About JLM Marine

Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.

As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.

We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.