Mercury 175 PROXS (2.5L) (1B516339 & Up) Outboard Motor Parts Diagram & Catalog – Free PDF Download

by JLM Marine 30 Apr 2025 0 Comments

Mercury 175 PROXS (2.5L) Outboard Motor Parts Diagram & Catalog – Free PDF Download

Accessories

Below is the parts list for Mercury 175 PROXS (2.5L) Accessories:

Position No.	Part Name	OEM Number	Supersedes
0	DECK FILL KIT, Oil	15969A3
0	DIODE ASSEMBLY, Dual Engine	812497A2
0	FLUSHING ATTACHMENT	44357Q2
0	FLUSH COUPLING	22-852400	56-820386A55
0	SWITCH/LANYARD KIT	87-19674Q2
0	MERCATHODE KIT	88334A2
0	HOSE EXTENSION KIT	41729A3
0	VISUAL WARNING SYSTEM, Low Oil/Overheat	17334A2
0	SMART TACH KIT Comment: 0-7000 RPM - Grey Face	79-859019A1
-	HARNESS ASSEMBLY	84-859314A1
0	SMART TACH KIT Comment: 0-7000 RPM - White Face	79-859067A1
-	HARNESS ASSEMBLY	84-859314A1
0	HARNESS ASSEMBLY	84-877561A2
0	ISOLATOR KIT, Battery	84-8M0094239	84-815366A 5

Air Compressor Components, SN 1B884476 and below

Below is the parts list for Mercury 175 PROXS (2.5L) Air Compressor Components, SN 1B884476 and below:

Position No.	Part Name	OEM Number	Supersedes
1	COMPRESSOR KIT, Air Comment: Unpainted	8M0060053	8M0057463, 8M0050656, 899113A03, 831998A21, 831998A16, 831998A22, 831998A13, 831998T 9, 831998A14 Unpainted
2	NOT SOLD SEPARATE, Body	NSS
3	END CAP ASSEMBLY	1100-8M0050792	1173-828131A12, 1173-828131A09, 1173-828131A 8
4	NOT SOLD SEPARATE, Retaining Ring	NSS
5	O-RING	25-67206001
6	O-RING	25-67206001
7	SCREW, (M6 x 20)	10-85593920
8	CONNECTING ROD ASSEMBLY	653-833146T06	653-833146T04, 653-833146T05, 653-833146T 3
9	NOT SOLD SEPARATE, Bearing	NSS
10	NOT SOLD SEPARATE, Bearing	NSS
11	NOT SOLD SEPARATE, Piston assembly (W/Rings and Pin)	NSS
12	NOT SOLD SEPARATE, Oil Scraper Ring	NSS
13	NOT SOLD SEPARATE, Top Ring	NSS
14	NOT SOLD SEPARATE, Oil Ring	NSS
15	NOT SOLD SEPARATE, Wrist Pin	NSS
16	NOT SOLD SEPARATE, Piston with Wrist Pin	NSS
17	RING, Lock, Lock	53-8348101
18	REED PLATE ASSEMBLY	835088A10	835088A 4
19	O-RING, (3.489 x .070)	25-67207
20	O-RING, (2.739 x .070)	25-832804
21	SEAL	26-828225
22	HEAD KIT, Compressor	835087A04
23	FITTING, (1.62 Inches)	22-8307534
23	FITTING, (1.87 Inches)	22-8M0042974
24	SCREW, (M8 x 35 MM)	10-82127335
25	SENSOR ASSEMBLY, Temperature	13536A14
26	RETAINER	137151
27	SCREW, (M8 x 14)	10-81893414
28	O-RING, (.468 x .078)	25-831985	25-885187
29	FITTING	22-151331
30	FITTING, Check Valve	21-428641
31	FITTING	22-856744	22-856744 1
32	FITTING	22-14868
33	NOT SOLD SEPARATE, Decal-Assy. Instructions	NSS
34	SCREW, (M6 x 20)	10-85593920
35	GROMMET	25-855349002	25-855349
36	FITTING, Elbow - 45 Degree - Brass (.125-27)	22-851975
37	SCREW, (M10 x 25) Hex Flange - Stainless Steel	10-4010825
38	STUD, (.312-18/.324-24 x 4.190)	16-858762001	16-8M0020427, 16-858762
39	WASHER, Special	12-854640
40	NUT, (.312-24)	11-46356
41	PULLEY	8M0138680
42	CLAMP	54-8M0024533
43	WASHER	12-884594
-	O-RING KIT	25-832804A03	25-832804A 1

Air Compressor Components, SN 1B884477 and up

Below is the parts list for Mercury 175 PROXS (2.5L) Air Compressor Components, SN 1B884477 and up:

Position No.	Part Name	OEM Number	Supersedes
1	COMPRESSOR ASSEMBLY, Air Comment: Black	8M0060053	8M0057463, 8M0050656, 899113A03, 831998A21, 831998A16, 831998A22, 831998A13, 831998T 9, 831998A14 Black
2	NOT SOLD SEPARATE, Body	NSS
3	END CAP ASSEMBLY	1100-8M0060381
4	SCREW, (M8 x 50)	10-8M0045380	10-891570050, 10-859096, 10-824460 50, 10-891570
5	O-RING	25-67206001
6	O-RING	25-67206001
7	SCREW, (M6 x 20)	10-85593920
8	CONNECTING ROD ASSEMBLY	653-833146T06	653-833146T04, 653-833146T05, 653-833146T 3
9	NOT SOLD SEPARATE, Bearing	NSS
10	NOT SOLD SEPARATE, Bearing	NSS
11	NOT SOLD SEPARATE, Piston assembly (W/Rings and Pin)	NSS
12	NOT SOLD SEPARATE, Oil Scraper Ring	NSS
13	NOT SOLD SEPARATE, Top Ring	NSS
14	NOT SOLD SEPARATE, Oil Ring	NSS
15	NOT SOLD SEPARATE, Wrist Pin	NSS
16	NOT SOLD SEPARATE, Piston with Wrist Pin	NSS
17	RING, Lock, Lock	53-8348101
18	REED PLATE ASSEMBLY	835088A10	835088A 4
19	O-RING, (3.489 x .070)	25-67207
20	O-RING, (2.739 x .070)	25-832804
21	SEAL	26-828225
22	HEAD KIT, Compressor	8M0073890
23	FITTING, (1.62 Inches)	22-8307534
23	FITTING, (1.87 Inches)	22-8M0042974
24	SCREW, (M8 x 35 MM)	10-82127335
25	SENSOR ASSEMBLY, Temperature	13536A14
26	RETAINER	137151
27	SCREW, (M8 x 14)	10-81893414
28	O-RING, (.468 x .078)	25-831985	25-885187
29	FITTING	22-151331
30	FITTING, Check Valve	21-428641
31	FITTING	22-856744	22-856744 1
32	FITTING	22-14868
33	NOT SOLD SEPARATE, Decal-Assy. Instructions	NSS
34	SCREW, (M6 x 20)	10-85593920
35	GROMMET	25-855349002	25-855349
36	FITTING, Elbow - 45 Degree - Brass (.125-27)	22-851975
37	SCREW, (M10 x 25) Hex Flange - Stainless Steel	10-4010825
38	STUD, (.312-18/.324-24 x 4.190)	16-858762001	16-8M0020427, 16-858762
39	WASHER, Special	12-854640
40	NUT, (.312-24)	11-46356
41	PULLEY	8M0138680
42	CLAMP	54-8M0024533
43	WASHER	12-884594
-	O-RING KIT	25-832804A03	25-832804A 1

Air Handler Components

Below is the parts list for Mercury 175 PROXS (2.5L) Air Handler Components:

Position No.	Part Name	OEM Number	Supersedes
-	AIR HANDLER ASSEMBLY	855633T34
1	ADAPTOR PLATE KIT	855420T03
2	GASKET	27-840484
3	GASKET	27-840485
4	REED BLOCK ASSEMBLY	840805T1
5	SCREW, (.250-20 x .880)	10-55715
6	PUMP ASSEMBLY, Oil	8M0185614
7	BUSHING	23-855364
8	GROMMET	25-855362001	25-855362
9	SCREW, (M8 x 35)	10-81893435
10	WASHER, (.344 x 1.00 x .063) Stainless Steel	12-817274	12-817274 1
11	PLENUM KIT, Air	850248T03
12	SCREW, (M8 x 30)	10-81893430
13	SENSOR ASSEMBLY	8M0148668
14	O-RING, (1.78 mm x .08 mm)	25-896699	25-888814
15	SCREW, (M4 x 16)	10-883942
16	THROTTLE BODY KIT	855422T03
17	O-RING	25-855423
18	SCREW, (M6 x 40)	10-82130040
19	SCREW, (M6 x 16)	10-1993716
20	SENSOR, MAP	854445
21	BRACKET, MAP Sensor	884522	804873, 841095
22	BRACKET	892296
-	LONG BLOCK ASSEMBLY	879809A08

Air Handler/Flywheel Cover

Below is the parts list for Mercury 175 PROXS (2.5L) Air Handler/Flywheel Cover:

Position No.	Part Name	OEM Number	Supersedes
1	COVER ASSEMBLY	827325T11
2	GROMMET	25-8M0153609
3	FILTER	35-853333T	35-853333
4	COVER	853352
5	GROMMET	25-857101
6	PLUG	19-89219001
7	GROMMET	25-855613
8	DECAL, Caution-Start in Gear	37-881865	37-825064
9	SENSOR	8M0082988	8M0030022, 828358 2
10	SCREW, (M5 x 16) Stainless Steel	10-40011107
11	PIN, Special (1.5 Inches)	8215832
11	PIN, Special (1.75 Inches)	17-8M0042972
12	J CLIP	54-883080
13	SCREW, (.250-20 x 1.500) Stainless Steel	10-817504
14	J CLIP	54-8M0024808
-	LONG BLOCK ASSEMBLY	879809A08

Air Hoses

Below is the parts list for Mercury 175 PROXS (2.5L) Air Hoses:

Position No.	Part Name	OEM Number	Supersedes
1	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
2	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
3	TUBING, (.312) (70.00 Inches Bulk) (Cut to 6 Inches)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
4	CLAMP, Hose (15.3)	54-8M0214964
5	HOSE	32-8502512
6	SLEEVE, (16.00 Inches)	23-85687631
7	HOSE, Air Balance (15.00 Inches)	32-804823005
8	HOSE/FITTING ASSEMBLY	32-804824
9	O-RING KIT	804532	25-803987
10	FITTING, Straight (.125-27)	22-16604
11	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
-	LONG BLOCK ASSEMBLY	879809A08

Bottom Cowl

Below is the parts list for Mercury 175 PROXS (2.5L) Bottom Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	BOTTOM COWL, Port	100-8M0107321
2	BOTTOM COWL, Starboard	103-834815A1
3	GASKET SET, Bottom Cowl	27-879147A11
4	RIGGING KIT	875266A2
5	INSERT, Bottom	859435T	859435
6	INSERT, Top	859434T	859434
7	FOAM	859343
8	SCREW, (#10-16 x 1.12)	10-92799
9	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
10	SCREW, (M6 x 40)	10-82130040
11	RETAINER	831209
12	PLUG	19-821908
13	WASHER	12-821915
14	CHECK VALVE	8219631
15	O-RING, (.299 x .103)	25-30641
16	FITTING	22-821952
17	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
18	HOSE	32-8M0039077	32-832078 2
19	CLAMP, (28.6)	54-850896
20	FITTING	22-8320763
21	FITTING, Tell-Tale	22-8M0077650	821904
22	BOOT, Idle Exhaust	889847	828216
23	CHECK VALVE ASSEMBLY, Drain	21-817519A1
24	SWITCH, Trim	87-8M0235191
25	HANDLE KIT	889740A02	821253F 1, 821253F 2, 821253F 4
26	SCREW, (M6 x 16 MM) Stainless Steel	10-8M0103805	10-885525 16
27	BUSHING	23-335891
28	O-RING, (.614 x .070)	25-48462
29	PAWL, Front Handle	8219423
30	WASHER, (.281 x .734 x .063)	12-69057
31	SEAL, Cowl (41.00 Inches)	8M0111278
32	SCREW, (#10-16 x .625)	10-8214281
33	CLIP	54-822873
34	NOT SOLD SEPARATE, Decal-Low Emission	NSS

Coil Plate Assembly

Below is the parts list for Mercury 175 PROXS (2.5L) Coil Plate Assembly:

Position No.	Part Name	OEM Number	Supersedes
-	NOT SOLD SEPARATE, Coil Plate Assembly-Complete	NSS
1	PLATE, Coil Mounting	884271
2	BUSHING	23-8502341
3	GROMMET	25-833155
4	SCREW, (M6 x 10)	10-82129110
5	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
6	CLIP, Tie Strap	54-899145
7	CABLE ASSEMBLY, Braided	84-858414A1
8	HARNESS ASSEMBLY, Coil	84-892910T03
9	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
10	CLIP, (.865)	54-883066
11	SENSOR	71-8M0157742
12	FITTING	22-8M0207782
13	TUBING, (52.00 Inches Bulk) (Cut to 4 Inches)	32-85978571
14	TEE, Fitting	22-875207
15	TUBING, (52.00 Inches Bulk) (Cut to 5 Inches)	32-85978571
16	SENSOR, Pressure (0 - 100 PSI) Comment: SN# 1B934545 & Below	881879T11	881879011, 881879A 6 SN# 1B934545 & Below
17	TUBING, (72.00 Inches Bulk) (Cut to 14-1/2 Inches)	32-85944975
18	COUPLER	22-8M0214971
19	TUBING, (72.00 Inches Bulk) (Cut to 52 Inches)	32-85944975
20	COIL KIT	300-8M0077471	300-879984T01, 339-879984A 1, 339-879984T00
21	SCREW, (M6 x 25 MM)	10-82129125
22	CABLE SET	84-881908T	84-821945T74, 84-821945T65
23	CONDUIT, (.350 Inside Diameter x 3.00 Feet Bulk)	32-828547353
24	SPARK PLUG, (NGK#IZFR6J-11)	33-843220Q	33-843220001, 33-8M0037136, 33-8M0048674, 33-8M0051514
25	SCREW, (.312-18 x 1.250)	10-60411
26	WASHER, (.323 x .563 x .063) Stainless Steel	12-8M0042642	12-70132
27	WASHER	12-49436

Crankshaft, Pistons and Connecting Rods

Below is the parts list for Mercury 175 PROXS (2.5L) Crankshaft, Pistons and Connecting Rods:

Position No.	Part Name	OEM Number	Supersedes
1	CRANKSHAFT ASSEMBLY	455-850690T7
2	WEAR SLEEVE	78662
3	BEARING, Ball (Lower)	30-67923T
4	RING	53-67446
5	CARRIER ASSEMBLY	54196A6
6	PACKING	65800
7	RING, Sealing	39-67377T
8	BEARING KIT	31-16756A6
9	NOT SOLD SEPARATE, Bearing-Race	NSS
10	PISTON Comment: (Starboard)	785-854687T5
10	PISTON Comment: (Port)	785-854686T5
11	RING SET, Piston (12 Rings per Set)	39-840684A12
12	LOCK RING	53-857196	40-52035
13	CONNECTING ROD ASSEMBLY	644-818141A13	644-818141A 2
14	SCREW, (.312-24 x .875)	10-763491
15	THRUST WASHER	12-8M0012298	12-812876
16	BEARING KIT	8M0234886
17	BEARING, Needle	29-8M0204691
-	GASKET SET, Engine	27-8M0046714	27-814754A00, 27-814754A98
-	LONG BLOCK ASSEMBLY	879809A08

Cylinder Block and End Caps

Below is the parts list for Mercury 175 PROXS (2.5L) Cylinder Block and End Caps:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER BLOCK ASSEMBLY	884-858961A35
2	STUD, (1.750 Inches)	16-8M0034455	16-818138 4
3	STUD, (.375-16/.375-24 x 5.620) Comment: (.375 x 5.62 Inches)	16-670654
3	STUD, (.375-16/.375-24 x 6.870)	16-8M0034454	16-78438 5
4	PIN, Dowel - Without Hole (.375 x .625)	17-43044
5	PIN (BEARING RACE)	17-8M0036405	17-67296
6	BRACKET	8M0111325
7	SCREW, (.312-18 x 1.500) Hex Flange	10-828213
8	COVER (Bottom)	76867
9	SCREW, (.312-18 x 2.00) Hex Flange	10-828214
10	SCREW, (.375-16 x 3.250)	10-66717
12	CAP, Nylon	26852
13	SCREW, (.250-20 x 1.750)	10-856832
14	NUT, (.250-20)	11-64015
15	END CAP ASSEMBLY	1159-832760T1
16	O-RING, (2.800 x .103)	25-54029
17	BEARING KIT	31-16756A4
18	NOT SOLD SEPARATE, Bearing Race	NSS
19	SEAL	26-41953
20	SCREW, (.312-18 x 1.00)	10-881190	10-855288
21	END CAP ASSEMBLY	1156-7809T1
22	O-RING, (3.237 x .103)	25-62700
23	SEAL	26-41953
24	SCREW, (.250-20 x .750)	10-28636
25	LOCKWASHER, (.250) Stainless Steel	13-26992
26	BRACKET, Throttle Position Indicator Mount	8538821
27	LEVER, Throttle Position Indicator	8519371
28	SCREW, (M6 x 25), Bracket to Crankcase	10-82130025
29	BUSHING	23-856954
30	WASHER, (.265 x .750 x .048) Stainless Steel	12-65567
31	GROMMET	25-8M0190980
32	INDICATOR, Throttle Position (Inside)	8M6005165
33	COVER, TPS	8582261
34	SCREW, (#10-32 x 2.00), TPS to Bracket	10-8508281
35	LINK ASSEMBLY	8M0084738
36	CABLE ASSEMBLY, Battery - Negative	84-88439A26
36	CABLE ASSEMBLY, Battery - Positive	84-88439A46
37	SCREW, (M8 x 14)	10-81893414
38	CABLE ASSEMBLY, (6.00 Inches) Black	84-93388A1
39	SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel	10-69035
40	HOSE, (57.00 Inches Bulk) (Cut to 1-1/4 Inches)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
41	HOSE, (57.00 Inches Bulk) (Cut to 1-1/2 Inches)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
42	PLUG, (.500-14)	22-883048
-	GASKET SET, Engine	27-8M0046714	27-814754A00, 27-814754A98
-	LONG BLOCK ASSEMBLY	879809A08

Cylinder Head

Below is the parts list for Mercury 175 PROXS (2.5L) Cylinder Head:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER HEAD ASSEMBLY Comment: (Port)	878109T1
1	CYLINDER HEAD ASSEMBLY Comment: (Starboard)	878110T1
2	SCREW, (.375-16 x 2.750)	10-8M0125882
3	PIN, Dowel (.250 x .625)	17-63779
4	GASKET	27-8M0204714
5	COVER	8M0039353	830737 2
6	THERMOSTAT, 62Â°C (143Â°F)	833072003	833072
7	SCREW, (M6 x 25)	10-82130025
8	SENSOR ASSEMBLY	8M0148668
9	O-RING, (1.78 mm x .08 mm)	25-896699	25-888814
10	SEAL	25-8M0149612
11	SEAL	8597721
-	GASKET SET, Engine	27-8M0046714	27-814754A00, 27-814754A98
-	LONG BLOCK ASSEMBLY	879809A08

Deck Oil Fill Kit, 15969A3 or 15969A5

Below is the parts list for Mercury 175 PROXS (2.5L) Deck Oil Fill Kit, 15969A3 or 15969A5:

Position No.	Part Name	OEM Number	Supersedes
1	DECK FILL KIT, Oil, With Hose	15969A3
2	DECK FILL KIT, Oil, With Out Hose	15969A13
3	PLATE	15966
4	DECK PLATE ASSEMBLY	15969A08
5	SCREW, (#8 x .625)	10-16324
6	CLAMP, Worm Gear	54-815504228	54-32781, 54-853232, 54-853432
7	ADAPTOR, Oil Filler	15967
8	O-RING, (2.225 x .210)	25-11332
9	HOSE, (100.00 Feet Bulk) , Oil Filler - Cut as Required	32-850719

Driveshaft Housing and Exhaust Tube

Below is the parts list for Mercury 175 PROXS (2.5L) Driveshaft Housing and Exhaust Tube:

Position No.	Part Name	OEM Number	Supersedes
1	HOUSING ASSEMBLY, Driveshaft - Black - Long Comment: (Long)	1590-8343T10
1	HOUSING, Driveshaft - Black - X-Long Comment: (X-Long)	3503-813563T1
2	STUD, (.437 x 2.69)	16-56295
3	SCREW, (.500-20 x 6.220)	10-898831	10-63474
4	CABLE ASSEMBLY, Ground	88238A10
5	MOUNT, Lower	77327
6	WASHER, (.8125)	12-49339
7	NUT, (.500-20)	11-898832	11-826708 17
8	SCREW, (.250-20 x .500) Stainless Steel	10-41508
9	WASHER, (.453 x .812 x .105) Stainless Steel	12-45176
10	NUT, (.437-20) Stainless Steel	11-8M0204653
11	CLAMP	54-8M0036782	54-67076
12	SCREW, (.312-18 x 1.250)	10-66727
13	COVER	100-8M4500752	8M0001130, 67077T
14	SCREW, (#12-24 x .620)	10-88417
15	NUT	11-35521
16	WASHER	12-48926
17	NUT, (.437-20) Stainless Steel	11-8M0204653
18	WASHER, (.406 x .734 x .063)	12-20553
19	NUT	11-69254
20	BOOT, Idle Exhaust	8M0039081	828212
21	PLUG	19-64649
22	GASKET	27-991734
23	SEAL (Lower)	66350001
24	TUBE, Exhaust	18276T
25	SEAL (Upper)	8M0039076	17726 1
26	EXTENSION ASSEMBLY, Exhaust	812834A2
27	STUD, (.250 x 1.38) Comment: Design-I	16-56766
27	SCREW, (0.25-20 x 1.50) Comment: Design-II	10-8M0047146
28	WASHER, (.281 x .625 x .065) Stainless Steel Comment: Design-I and Design-II	12-35044
29	NUT	11-888500
30	GASKET	27-183076
31	TUBE, Water Comment: (Long)	32-8M0042788	32-859097 1 (Long)
31	TUBE, Water Comment: (X-Long)	32-8M0042790	32-859097 2 (X-Long)
32	PLATE ASSEMBLY, Driveshaft Housing	18233A20
33	SEAL	8M0043165	814701 2
34	BRACKET	68011
35	SCREW, (#10-16 x .500)	10-878608	10-812832
36	PIN, Dowel - Without Hole (.375 x .625)	17-43044
37	SEAL	26-38970
-	GASKET SET, Engine	27-8M0046714	27-814754A00, 27-814754A98

Electrical Plate Assembly

Below is the parts list for Mercury 175 PROXS (2.5L) Electrical Plate Assembly:

Position No.	Part Name	OEM Number	Supersedes
-	NOT SOLD SEPARATE, Electrical Plate Assembly-Complete	NSS
1	PLATE	899071T01	899071T
2	CLIP, Tie Strap	54-899145
3	SCREW, (M6 x 14)	10-82129114
4	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
5	RELAY ASSEMBLY	8M0207773
6	BRACKET	828102
7	GROMMET	25-818967
8	BUSHING	23-8M0214955
9	SCREW, (M6 x 25 MM)	10-82129125
10	HARNESS ASSEMBLY, Engine	84-892926T03
-	FUSE, Mini - Yellow - 20 Ampere	88-832969T20	88-832969 20
-	FUSE, Mini - Blue - 15 Ampere	88-832969T15	88-832969 15
-	FUSE, Mini - Gray - 2 Ampere	88-8M0207797
-	FUSE, Mini - Tan - 5 Ampere	88-832969T05	88-832969 5
-	HARNESS ASSEMBLY (Direct Injector)	879346A49	84-858781A 2
-	HARNESS ASSEMBLY (Fuel Injector)	879346A50	84-858780A 2
-	HARNESS ASSEMBLY, Alternator, Alternator	84-881262A2
-	HARNESS ASSEMBLY (Throttle Position Sensor)	879346A41	84-878073A 2
11	HOT STUD ASSEMBLY	85-875302A1
12	NUT, (M8) Stainless Steel	11-400213
13	WASHER	12-85172
14	CABLE ASSEMBLY, Black	84-93388T21
15	CABLE ASSEMBLY, Starter	84-8M0006811
16	HARNESS ASSEMBLY, Fuse - 100 Ampere	84-878231A03
17	LOCKWASHER, (.312)	13-53166
18	NUT, (M8) Stainless Steel	11-400213
19	CABLE ASSEMBLY, Battery - Positive	84-88439A46
20	SOLENOID ASSEMBLY, (#10-32 / .3125-18 Terminals)	89-817109A2
21	GROMMET	25-822179
22	BUSHING	23-8M0214955
23	CABLE ASSEMBLY, (4.00 Inches) Black	84-88807A16
24	NUT, Brass	10-32,11-45076
25	CAP NUT,	10-32,11-813938
26	NUT, (.312-18)	11-8M0204668
27	HARNESS ASSEMBLY, Trim	84-819514T26
28	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275

Exhaust Manifold and Exhaust Plate

Below is the parts list for Mercury 175 PROXS (2.5L) Exhaust Manifold and Exhaust Plate:

Position No.	Part Name	OEM Number	Supersedes
1	GASKET	27-190506
2	PLATE ASSEMBLY, Exhaust Divider	828343A05	828343A 4
3	SEAL, (12.50 Inches)	26-814754	42838 1, 69668, 88726
4	SCREW AND WASHER, (.312-18 x 1.500)	10-8263561
5	SCREW, (.312-18 x 1.00)	10-881190	10-855288
6	COVER, Relief Valve	8M0039767	68729 1
7	SCREW, (.312-18 x 1.375)	10-31984
8	SCREW, (#10-16 x .750)	10-69570
9	WASHER	12-76451
10	DIAPHRAGM	144791
11	DEFLECTOR, Water	16496
12	PLATE	16497A1
13	GASKET	27-78690002
14	SPRING, (Stainless Steel)	24-42996
15	POPPET	14480
16	GROMMET	25-64872
17	CARRIER	65848
18	GASKET	27-991764
19	PLATE, Exhaust	850814T4
20	PIN, Dowel - Without Hole (.375 x .625)	17-43044
21	SEAL	8M0043164	814701 1
22	BRACKET	680101
23	SCREW, (#10-16 x .500)	10-878608	10-812832
24	GROMMET	25-19565002
25	WASHER, (.406 x .734 x .063)	12-20553
26	NUT	11-69254
27	BUSHING	23-27132
28	SCREW, (.312-18 x 1.250)	10-66727
29	SCREW, (.312-18 x 2.50)	10-68783
30	SCREW, (.375-16 x 3.500)	10-898833	10-66725
31	BRACKET, Front	812905T	812905A 5
32	SCREW, (.3125-18 x .50)	10-8055571
33	WASHER	12-187031
34	GROMMET	25-18778001
35	BRACKET ASSEMBLY, Rear	18578T09
36	GROMMET	25-12602002
37	SCREW, (.312-18 x 1.750)	10-881892	10-75206
38	PLUG, (.500-14)	22-883048
-	GASKET SET, Engine	27-8M0046714	27-814754A00, 27-814754A98
-	LONG BLOCK ASSEMBLY	879809A08

Flywheel/Alternator

Below is the parts list for Mercury 175 PROXS (2.5L) Flywheel/Alternator:

Position No.	Part Name	OEM Number	Supersedes
1	ALTERNATOR KIT	8M0064021	889955A03, 881248T, 875285T 1
2	SCREW, (M10 x 1.5)	10-8M0012503	10-40108100
3	SCREW, (M10 x 120) Hex Flange - Stainless Steel	10-40108120
4	WASHER, (.390 x 1.00 x .06)	12-8M0042641	12-29395
5	MOUNT	23-856975	849639
6	BRACKET	858391T01	858391T, 856972T
7	WASHER, (.406 x 1.250 x .089)	12-845998
8	BRACKET	858393T01	858393T, 856973T
9	NUT, (M10) Brass/Nickel Plated	11-826292
10	SCREW, (M10 x 55)	10-82446155
11	CABLE ASSEMBLY	84-856583T2
12	PIN, Special (1.5 Inches)	8215832
12	PIN, Special (1.75 Inches)	17-8M0042972
13	BRACKET	857142T	856974T
14	SCREW, (.312-18 x 1.00) Stainless Steel With Nylon Patch	10-812618	10-73169, 10-847568
15	SPRING	24-855798001	24-855798
16	ARM TENSIONER ASSEMBLY	856815T2
17	STUD, (M10 x 85)	16-8M0034457	16-856900
18	NUT, (M10) Brass/Nickel Plated	11-826292
19	BUSHING	23-8568941
20	WASHER	12-4002320
21	PULLEY ASSEMBLY	8M6005030
22	SCREW, (M10 x 35) Hex Flange - Stainless Steel	10-4010835
23	BELT	57-828507Q4
24	FLYWHEEL	281-859734T1
25	NUT, (.625-18)	11-52901
26	WASHER, (.641 x 1.250 x .190)	12-33001
27	PLUG, Yellow	19-45907
28	NUT, (M6) Stainless Steel	11-401386
29	WASHER	12-4002319

Fuel Hoses

Below is the parts list for Mercury 175 PROXS (2.5L) Fuel Hoses:

Position No.	Part Name	OEM Number	Supersedes
1	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
2	CLAMP, Hose (15.3)	54-8M0214964
3	CONNECTOR	22-858955
4	HOSE, (57.00 Inches Bulk) (Cut to 7-1/2 Inches)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
5	HOSE, To Fuel Pump	32-8M0064784	32-897972, 32-856822A 1
6	HOSE ASSEMBLY, (25.50 Inches)	32-8M0062344	32-858757A 1
7	HOSE, Fuel Return	32-804822
8	HOSE, Fuel Balance (16.00 Inches)	32-804821005
9	O-RING KIT	25-804840
10	HOSE	32-8M0064634	32-856778 70
11	HOSE	32-8M0064635	32-856778 87
12	SLEEVE, (27.00 Inches Bulk)	23-85686953
13	CLAMP, (15.7)	54-8M0214911
14	CHECK VALVE	21-8557611

Fuel Pump

Below is the parts list for Mercury 175 PROXS (2.5L) Fuel Pump:

Position No.	Part Name	OEM Number	Supersedes
-	PUMP ASSEMBLY, Fuel	14360T75
1	NOT SOLD SEPARATE, Body-Fuel Pump	NSS
2	DIAPHRAGM KIT	21-857005A1
3	NOT SOLD SEPARATE, Diaphragm	NSS
4	NOT SOLD SEPARATE, Retainer	NSS
5	NOT SOLD SEPARATE, Spring	NSS
6	NOT SOLD SEPARATE, Cap	NSS
7	NOT SOLD SEPARATE, Spring	NSS
8	NOT SOLD SEPARATE, Cap	NSS
9	NOT SOLD SEPARATE, Diaphragm	NSS
10	NOT SOLD SEPARATE, Gasket-Boost	NSS
11	NOT SOLD SEPARATE, Gasket-Pulse	NSS
12	GASKET	27-8M0204705
13	PLATE	987752
14	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
15	SCREW, (M5 x 40)	10-82104540
16	SCREW, (M6 x 50), Pump to Crankcase	10-82130050
17	BASE	144303
18	FITTING	22-291112
19	FITTING, Elbow 45 Degree (1.25)	22-782792
20	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
21	HOSE AND SLEEVE ASSEMBLY, (18.00 Inches)	32-8M0043979	32-856822A 2
22	CONNECTOR	22-822769
-	GASKET SET, Engine	27-8M0046714	27-814754A00, 27-814754A98
-	LONG BLOCK ASSEMBLY	879809A08

Fuel Rails

Below is the parts list for Mercury 175 PROXS (2.5L) Fuel Rails:

Position No.	Part Name	OEM Number	Supersedes
-	FUEL RAIL ASSEMBLY, Complete	8M0185153
1	NOT SOLD SEPARATE, Fuel Rail (Port)	NSS
2	NOT SOLD SEPARATE, Fuel Rail (Starboard)	NSS
3	CLAMP	54-804830
4	SCREW PACKAGE, (2 Per)(M5 x 10)	10-804525001	804525
5	VALVE ASSEMBLY, (.375 Inch Diameter)	8M0047053	883542, 804838A 1
6	O-RING KIT	25-804840
7	CAP, Shrader Valve - Brass	22-805515	19-804839001, 19-804839
8	PLUG (Port)	19-804835
9	CLAMP	8M0041097
10	CLAMP	54-8048311
11	INJECTOR	8M0222157
12	O-RING KIT	25-804530
13	O-RING KIT	25-804529
14	CLAMP	804522
15	CLAMP	54-880808
16	REGULATOR, Air	880807T04
17	O-RING KIT	25-880809
18	CLAMP	54-804832
19	SCREW PACKAGE, (M5 x 16) (2 Per)	804526
20	COVER	804535001	804535
21	SPRING	24-804534
22	DIAPHRAGM ASSEMBLY	804533
23	O-RING	25-804536
24	PLUG (Starboard)	19-804834
25	FITTING	22-804836
26	O-RING KIT	804532	25-803987
27	INJECTOR ASSEMBLY, Air	8M6001744	8M0065917, 884595A01, 884595A 1, 884595A02
28	SEAL KIT, Direct Injector	26-804875	26-835083
29	STUD, (M10 x 92)	16-8M0063255
30	NUT, (M10) Brass/Nickel Plated	11-826292
31	WASHER ASSEMBLY, Cupped	12-828694A1
32	CLIP, Tie Strap	54-899145

Gasket Set Components-Complete-Powerhead and Lower Unit

Below is the parts list for Mercury 175 PROXS (2.5L) Gasket Set Components-Complete-Powerhead and Lower Unit:

Position No.	Part Name	OEM Number	Supersedes
-	GASKET SET, Engine, Powerhead and Lower Unit	27-8M0046714	27-814754A00, 27-814754A98
-	DIAPHRAGM KIT, Fuel Pump	21-857005A1
-	NOT SOLD SEPARATE, Diaphragm	NSS
-	NOT SOLD SEPARATE, Retainer	NSS
-	NOT SOLD SEPARATE, Spring	NSS
-	NOT SOLD SEPARATE, Cap	NSS
-	NOT SOLD SEPARATE, Spring-Boost	NSS
-	NOT SOLD SEPARATE, Cap-pring End	NSS
-	NOT SOLD SEPARATE, Gasket-Boost	NSS
-	NOT SOLD SEPARATE, Gasket-Pulse	NSS
-	GASKET, Fuel Pump	27-8M0204705
-	O-RING, (2.800 x .103)	25-54029
-	O-RING, (3.237 x .103)	25-62700
-	GASKET, Thermostat Cover	27-8M0204714
-	PACKING, Crankshaft-Bottom	65800
-	GASKET, Divider Plate	27-190506
-	SEAL, (12.50 Inches), Divider Plate	26-814754	42838 1, 69668, 88726
-	GASKET, Relief Valve Cover and Plate	27-78690002
-	GASKET, Cylinder Block	27-991764
-	O-RING, (.612 x .103), Tilt Tube	25-45711
-	GASKET, Driveshaft Housing	27-991734
-	SEAL, Driveshaft Housing Plate	26-38970
-	GASKET, Driveshaft Housing Plate	27-183076
-	O-RING, (.862 x .103), Shift Shaft Bushing	25-25439
-	GASKET, Water Pump Base-Lower	27-8M0204678
-	O-RING, (2.175 x .175), Water Pump Base-Lower	25-8M0142854
-	GASKET, Water Pump Base-Lower	27-8M0090319	27-85608 1
-	GASKET, Water Pump Base-Upper	27-858524	27-85609 1, 27-85609B 1
-	SEAL, Water Pump Body	26-38970
-	O-RING, Bearing Carrier	25-8M0214920
-	GASKET, Cylinder Block Comment: Not used for this application	27-11338
-	GASKET, Divider Plate Comment: Not used for this application	27-190503
-	GASKET, Exhaust Diffuser Comment: Not used for this application	27-782461

Gear Housing(Driveshaft)

Below is the parts list for Mercury 175 PROXS (2.5L) Gear Housing(Driveshaft):

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Complete (4.75 Inch/120.65 mm Torpedo Diameter) Comment: (Standard - Long - 1.87:1)	1647-9148T84
-	GEAR HOUSING ASSEMBLY, Complete (4.75 Inch/120.65 mm Torpedo Diameter) Comment: (Standard - X-Long - 1.87:1)	1647-9148T85
1	GEAR HOUSING ASSEMBLY, Basic	1647-9148T93
2	PIN, Dowel - Without Hole (.375 x .625)	17-43044
3	STUD, (.437-14/.437-20 x 3.120) Comment: (Long)	16-786382
3	STUD, (.438 x 3.82 Inches) Comment: (X-Long)	16-8M0034464	16-18978 3 (X-Long)
4	STUD, (.437-14/.437-20 x 2.060)	16-8M0133358
5	STUD, (.312-18/.324-24 x 3.380)	16-8M0034463	16-56297 2
6	STUD, (.250-20/.250-28 x 3.125)	16-306671
7	FILLER BLOCK	8M0039169	67891
8	BEARING ASSEMBLY, Roller	31-42647A1
9	ANODE	97-826134Q	826134, 826134A 1
10	SCREW, (M6 x 40)	10-4000333
11	NUT, (M6) Stainless Steel	11-401386
12	FITTING	22-881866	22-859432
13	SLEEVE	23-29804T
14	NOT SOLD SEPARATE, Pinion Gear	NSS
15	WASHER	12-92721
16	NUT, (.625-18)	11-35921
17	SHIM SET	15-42637A1
18	SCREW KIT, Drain	10-79953Q04
19	SEAL	26-8M0204693
20	SHIFT SHAFT	789022
21	O-RING, (.862 x .103)	25-25439
22	BUSHING ASSEMBLY	23-77631A2
23	SEAL, Oil	26-8M0204708
24	WASHER	12-77674
25	DRIVESHAFT, Long	45-897624T	45-44000 1
25	DRIVESHAFT, X-Long	45-897625T	45-44209 1
26	BEARING ASSEMBLY, Roller/Cup	31-8M0146566
27	NOT SOLD SEPARATE, Cup	NSS
28	RETAINER	8245191
29	BASE ASSEMBLY, Water Pump	46-8M0077147	46-42579A 3
30	NOT SOLD SEPARATE, Retainer	NSS
31	GASKET	27-8M0204678
32	O-RING, (2.175 x .175)	25-8M0142854
33	SEAL, Oil	26-89238
34	SEAL, Oil	26-16977
35	GASKET, Lower	27-8M0090319	27-85608 1
36	GASKET	27-858524	27-85609 1, 27-85609B 1
37	FACE PLATE	8M0204677
38	BODY ASSEMBLY, Water Pump	46-96148T1
39	INSERT	48752T
40	SEAL	26-38970
41	IMPELLER	47-89984T3
42	KEY	28-8M0214992
43	SCREW, (#14-8 x 2.25)	10-8M0215009
44	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
45	NUT, (.250-28)	11-8267119
46	WASHER	12-36001
47	NUT	11-13436
-	BODY ASSEMBLY, Water Pump	46-96148A8
-	SEAL KIT	26-89238A2
-	BEARING AND SEAL KIT (Without Forward Bearing)	31-803033T1
-	GASKET SET, Engine	27-8M0046714	27-814754A00, 27-814754A98
-	GEAR ASSEMBLY, Pinion/Forward	43-803615T2

Gear Housing, Propeller Shaft

Below is the parts list for Mercury 175 PROXS (2.5L) Gear Housing, Propeller Shaft:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY, Complete (4.75 Inch/120.65 mm Torpedo Diameter) Comment: (Long- 1.87:1)	1647-9148T84
-	GEAR HOUSING ASSEMBLY, Complete (4.75 Inch/120.65 mm Torpedo Diameter) Comment: (X-Long - 1.87:1)	1647-9148T85
1	GEAR HOUSING ASSEMBLY, Basic	1647-9148T93
2	FOLLOWER ASSEMBLY	89594A1
3	SHIFT CAM	789562
4	ROD	828287
5	GEAR ASSEMBLY, Pinion/Forward	43-803615T2
6	SHIM SET	15-44491A1
7	BEARING SET, Cup And Cone	31-30894A1
8	NOT SOLD SEPARATE, Cup	NSS
9	BEARING, Needle	31-30895T
10	RING, Retaining	53-856823
11	CLUTCH	52-859340T	52-854735T, 52-828288
12	PIN, Cross	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
13	PIN, Detent	17-828356
14	SPRING	24-30893
15	PROPELLER SHAFT	44-94148
16	GEAR ASSEMBLY, Reverse - 15/28	43-828175A1
17	SPACER	23-824108
18	RING, Thrust	681001
19	BEARING, Ball	30-88957T
20	O-RING	25-8M0214920
21	CARRIER ASSEMBLY, Bearing	43567T1
22	BEARING, Needle	31-30956T
23	SEAL, Oil (Inside)	26-14077
24	SEAL (Outside)	26-8M0204670
25	KEY	28-30281
26	TAB WASHER	14-79447
27	RETAINER	8M2011027	79448
28	ANODE Comment: (Aluminum)	97-76214Q5
28	ANODE KIT Comment: (Aluminum-Quicksilver Branded)	97-76214Q5
28	ANODE KIT Comment: (Aluminum- Mercury Branded)	97-76214T5
28	ANODE KIT Comment: (Magneseum)	97-76214A6
29	SCREW, (.437-14 x 1.750)	10-8M0204686
30	SCREW, (.375-16 x 1.00)	10-65210
31	WASHER, (.453 x .812 x .105) Stainless Steel	12-45176
32	NUT, (.437-20) Stainless Steel	11-8M0204653
-	NOT SHOWN, See Accessory Guide-Propellers-For Appropriate Hardware. (Thrust Washers/Nuts)	NS
-	SEAL KIT	26-89238A2
-	FOLLOWER ASSEMBLY, Clutch/Cam	52-803491T1
-	BEARING AND SEAL KIT (W/O Foward Bearing)	31-803033T1
-	GEAR ASSEMBLY, Pinion/Forward	43-803615T2
-	GASKET SET, Engine	27-8M0046714	27-814754A00, 27-814754A98

Mercathode Kit

Below is the parts list for Mercury 175 PROXS (2.5L) Mercathode Kit:

Position No.	Part Name	OEM Number
1	MERCATHODE KIT	88334A2
2	MERCATHODE ASSEMBLY	88334A4
3	SCREW, (#9-14 x .875)	10-22793
4	WASHER, (.192 x .375 x .0312) Stainless Steel	12-30164
5	NUT, Brass	10-32,11-45076
6	ELECTRODE ASSEMBLY	72958A5
7	O-RING, (.796 x .139)	25-8M0204645
8	SCREW, (#10-16 x 1.250) Stainless Steel	10-87698
9	ANODE ASSEMBLY	97-72957A5
10	O-RING, (.796 x .139)	25-8M0204645
11	SCREW, (#10-16 x 1.250) Stainless Steel	10-87698
12	FUSE, 20 Ampere	88-8M0207796
13	CABLE ASSEMBLY, (5.00 Inches) Red	84-95084A10
14	CABLE ASSEMBLY, (64.00 Inches)	84-95084A13
15	CABLE ASSEMBLY, (72.00 Inches) Black	84-79138A8

Oil Injection Components

Below is the parts list for Mercury 175 PROXS (2.5L) Oil Injection Components:

Position No.	Part Name	OEM Number	Supersedes
1	TUBING, (38.00 Inches Bulk) (Cut to 24 Inches)	32-8M0054152	32-856060 65
2	TUBING, (38.00 Inches Bulk) (Cut to 18-1/2 Inches)	32-8M0054152	32-856060 65
3	TUBING, (38.00 Inches Bulk) (Cut to 16-1/2 Inches)	32-8M0054152	32-856060 65
4	TUBING, (38.00 Inches Bulk) (Cut to 24-1/2 Inches)	32-8M0054152	32-856060 65
5	TUBING, (38.00 Inches Bulk) (Cut to 27 Inches)	32-8M0054152	32-856060 65
6	CHECK VALVE	21-858805
7	TIE STRAP, (5.50 Inches)	8M0214940
8	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
8	TIE STRAP, (4.00 Inches)	56762
9	HOSE, (24.00 Inches Braided)	32-892830053
10	HOSE, (40.00 Inches Bulk) (Cut to 32 Inches)	32-8M0054213	32-855834 66
11	CHECK VALVE, To Block	21-8781051
12	FITTING	22-8M0207780
13	HOSE, (57.00 Inches Bulk) (Cut to 6 Inches)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
14	NOT SOLD SEPARATE, Cap	NSS
15	HOSE	32-875289
16	CONNECTOR	22-858955
17	FILTER, Oil - In Line	35-875284T01	35-875284001, 35-875284
18	HOSE, (2.00 Inches)	32-875283
19	RESERVOIR ASSEMBLY	1200-8M0063190	833069T 9
20	NOT SOLD SEPARATE, Decal-Reservoir	NSS
21	GROMMET	25-855362001	25-855362
22	WASHER	12-49436
23	SCREW, (.312-18 x 1.250)	10-60411
24	BUSHING	23-855364
25	SWITCH ASSEMBLY	87-856156T02	87-856156A 2
26	SCREW, (.164-18 x .375)	10-58376
27	WASHER, (.203 x .562 x .060) Stainless Steel	12-72761
28	CLAMP	54-814634
29	HOSE, (57.00 Inches Bulk) (Cut to 4-3/4 Inches)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
30	CONNECTOR	22-858955
-	LONG BLOCK ASSEMBLY	879809A08

Oil Lines

Below is the parts list for Mercury 175 PROXS (2.5L) Oil Lines:

Position No.	Part Name	OEM Number	Supersedes
1	TUBING, (38.00 Inches Bulk) (Cut to 30 Inches)	32-8M0054152	32-856060 65
2	TUBING, (38.00 Inches Bulk) (Cut to 25 Inches)	32-8M0054152	32-856060 65
3	FITTING, Elbow 90 Degree (.0625-27)	22-887801
4	CHECK VALVE, 90 Degree (.0625-27)	21-8592352
5	TUBING, (38.00 Inches Bulk) (Cut to 16-1/2 Inches)	32-8M0054152	32-856060 65
6	FITTING	22-151333
7	TIE STRAP, (5.50 Inches)	8M0214940
8	TUBING, (38.00 Inches Bulk) (Cut to 22 Inches)	32-8M0054152	32-856060 65
9	FITTING, Tee	22-59169003
10	TUBING, (38.00 Inches Bulk) (Cut to 1-1/2 Inches)	32-8M0054152	32-856060 65
11	TUBING, (38.00 Inches Bulk) (Cut to 4 -3/4 Inches)	32-8M0054152	32-856060 65
12	TUBING, (38.00 Inches Bulk) (Cut to 3-1/2 Inches)	32-8M0054152	32-856060 65
13	CHECK VALVE	21-426233
14	CHECK VALVE	21-426982
-	LONG BLOCK ASSEMBLY	879809A08

PCM Mounting

Below is the parts list for Mercury 175 PROXS (2.5L) PCM Mounting:

Position No.	Part Name	OEM Number
1	PCM, Propulsion Control Module Comment: SN# 1B934544 & Below	89790639T
1	PCM, Propulsion Control Module Comment: SN# 1B934545 & Up	8M0073376
2	SCREW, (M6 x 25)	10-82130025
3	WASHER, (.265 x .750 x .048) Stainless Steel	12-65567
4	GROMMET	25-8M0190980
5	BUSHING	23-856954
6	BRACKET	858953
7	SCREW, (M6 x 14)	10-82129114
8	SCREW, (M6 x 12)	10-82130012
9	CONNECTOR ASSEMBLY, Weather Cap - Male	830796A04
10	CONNECTOR ASSEMBLY, Weather Cap 6 Pin	877613A02
11	J CLIP	54-8M0024808

Power Trim Components

Below is the parts list for Mercury 175 PROXS (2.5L) Power Trim Components:

Position No.	Part Name	OEM Number	Supersedes
-	POWER TRIM ASSEMBLY, Complete	855998A11	855998A08, 855998A07, 855998A10, 855998A09, 855998A05, 855998A 3
1	TRIM MOTOR	878265A4
2	NOT SOLD SEPARATE, Armature	NSS
3	NOT SOLD SEPARATE, End Frame	NSS
4	SCREW, (M6 x 30)	10-82494830
5	LOCKWASHER, (M6)	13-400256
6	DRIVESHAFT	8782451
7	PO CHECK KIT	878410A1
8	MANUAL RELEASE ASSEMBLY, Includes Reference #26	893929A01	813442A 2
9	SHAFT KIT	8M0142997
10	PIN	17-878267	17-44431
11	TILT CYLINDER ASSEMBLY	878235A03	878235A02, 878235A 1
12	GUIDE KIT, Includes Reference #26	878239A02	878239A 1
13	O-RING KIT, Includes Reference #26	8M0142999
14	SHOCK ROD KIT, Includes Reference #26	8M0168219
15	PISTON ASSEMBLY, Memory	8M0143000
16	REPAIR KIT, Check Valve, Includes Reference #26	878406A02	878406A 1
17	PISTON ASSEMBLY	878414T01	878414A 1
18	PISTON ASSEMBLY	878413A1
19	GUIDE ASSEMBLY	1100-8M0021648	878243A 1
20	RESERVOIR KIT	878264A1
21	PLUG ASSEMBLY	19-811613
22	SCREW, (M6 x 14)	10-4000327
23	WASHER	12-4002315
24	PUMP KIT	892251A01	878411A 1
25	REPAIR KIT, Power Trim	878408A1
26	PIN, Trilobe	17-821539	17-13794, 17-19603
27	SCREW, (M10 x 30)	10-858771
28	WASHER	12-4002319
29	ANODE KIT	97-818298Q1
30	SCREW, (M6 x 25)	10-8M0204707
31	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
32	SHAFT	99625002
33	C WASHER	8M0084613	69205
34	CLAMP	54-26550
35	SCREW, (#10-16 x .600)	10-878609	10-812832 1
36	CONDUIT, (.350 Inside Diameter x 3.00 Feet Bulk), Cut to 12 Inches	32-828547353
37	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275

Service/Support Material

Below is the parts list for Mercury 175 PROXS (2.5L) Service/Support Material:

Position No.	Part Name	OEM Number	Supersedes
-	PARTS MANUAL, 175 PROXS (2.5L)	90-898101926
-	OPERATION MANUAL, 135/150/175, English Comment: SN# 1B785122 & Below	90-10299082
-	OPERATION MANUAL, 135-175 ProXS Optimax Comment: SN# 1B785123 THRU 1B935209	90-8M0055670	90-10299091 SN# 1B785123 THRU 1B935209
-	OPERATION MANUAL, 2.5L Opti Comment: SN# 1B935210 THRU 2B011451	90-8M0077319
-	OPERATION MANUAL, 2.5L Opti Comment: SN# 2B011452 & Up	90-8M0080077
-	SERVICE MANUAL	90-8M0057453	90-859494R02, 90-859494R 1
-	DECAL, EPA Label Information Comment: (2007)	37-879147A21
-	DECAL, EPA Label Information Comment: (2008)	37-804657A08
-	NOT SOLD SEPARATE, DECAL, EPA (2009 & Up) Comment: Contact Mercury Marine Warranty Administration for Replacement (Service Bulletin 2009-18)	NSS

Starter Motor

Below is the parts list for Mercury 175 PROXS (2.5L) Starter Motor:

Position No.	Part Name	OEM Number	Supersedes
1	STARTER MOTOR ASSEMBLY	50-892339T01	50-892339T, 50-853329T
2	NOT SOLD SEPARATE, Thru Bolt	NSS
3	GEAR KIT	43-880805A1
4	SOLENOID KIT	809463A1
5	BRUSH SET	8M0065258
6	SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel	10-69035
7	CABLE ASSEMBLY, (6.00 Inches) Black	84-93388A1
8	DECAL, Warning	37-8272822
9	LOCKWASHER, (M5)	13-400255
10	NUT, (M5) Stainless Steel	11-400211
11	LOCKWASHER, (.312)	13-8M0204647
12	NUT, (M8) Stainless Steel	11-400213
13	COLLAR	23-8M0034918	23-8M0001391, 56703
14	STOP	8M0043276	879845

Switch/Lanyard Assembly

Below is the parts list for Mercury 175 PROXS (2.5L) Switch/Lanyard Assembly:

Position No.	Part Name	OEM Number	Supersedes
-	SWITCH/LANYARD KIT Comment: Quicksilver Branded	87-19674Q2
-	SWITCH/LANYARD KIT	87-19674Q2
1	SWITCH ASSEMBLY, Lanyard	87-19674A1
2	SCREW, (.190-16 x 1.750) Stainless Steel	10-18303
3	ADAPTER	813679	12051
4	LANYARD ASSEMBLY	15920Q54
5	SCREW, (#10-32 x 2.00) Stainless Steel	10-32866
6	CLAMP, Mounting	18321
7	WASHER, (.200 x .440 x .032)	12-24676
8	NUT, Stainless Steel	10-32,11-68219
9	RETAINER	79146
10	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
11	CABLE ASSEMBLY	84-11149A3
12	INSULATOR, (2.00 Inch)	85-623594
NS	NEOPRENE, (8 Ounce)	92-257113

Swivel Bracket and Steering Arm

Below is the parts list for Mercury 175 PROXS (2.5L) Swivel Bracket and Steering Arm:

Position No.	Part Name	OEM Number	Supersedes
1	SWIVEL BRACKET ASSEMBLY, Black	1499-8M0102865	1499-8710T20
2	O-RING	25-8M0214926
3	BUSHING	23-818764	23-67669
4	SPACER	23-816039
5	SEAL, Oil (Lower)	26-87735
6	FITTING, Grease	22-8M0169589
7	BUSHING	23-821207	23-99608
8	THRUST WASHER	12-816432
9	YOKE, Bottom	878182T01	878182T
10	RING, Retaining	53-67684
11	STRIKER PLATE	8M0045383	99630 1
12	LOCKWASHER, (.375)	13-58643
13	NUT, (.375-24)	11-46335
14	SCREW, (.250-28 x .500)	10-64014
15	NOT SOLD SEPARATE, Decal-Serial Overlaminate	NSS
16	SENDER ASSEMBLY, Trim	8M0074846	821180A 6
17	SCREW, (#10-24 x .750)	10-852368	10-56682
18	LOCKWASHER, Stainless Steel	10,13-26996
19	WASHER, (.203 x .406 x .040)	12-89302
20	SWIVEL PIN ASSEMBLY, Steering Arm - Stainless Steel	17-8M0132731
21	SCREW, (.437-20 x 7.500)	10-8M0176309
22	BUMPER, Top Yoke	8M0000516	88882 1
23	MOUNT	77326
24	WASHER	12-66921
25	WASHER	12-78688
26	NUT, (.437-20) Stainless Steel	11-8M0204653
27	LINK ROD ASSEMBLY	92876A12
28	SCREW, (.375-24 x 1.250)	10-849838	10-14000
29	NUT, (.375-24) Stainless Steel	11-8M0204726
29	NUT, (.375-24) Brass	11-8M0204726
30	WASHER, (.390 x .625 x .062) Stainless Steel	12-37828
31	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275

Throttle Lever and Shift Shaft

Below is the parts list for Mercury 175 PROXS (2.5L) Throttle Lever and Shift Shaft:

Position No.	Part Name	OEM Number	Supersedes
1	LEVER, Throttle Control	8M0040990	850389 1
2	SCREW, (.375-16 x 1.75)	10-818165	10-55337
3	BUSHING	23-55164
4	SPACER	23-858959
5	SCREW, (.250-20 x 2.125)	10-64022
6	NUT, (.250-20)	11-64015
7	CAP, Nylon	26852
8	INSERT	42927
9	WASHER	12-35459
10	NUT, (M6) Stainless Steel	11-401386
11	BRACKET ASSEMBLY, Anchor	814283T6
12	LATCH	98889
13	DRIVE SCREW	10-42975
14	CUP	39519
15	WEAR PLATE	52100
16	LATCH	8M0036768	38279
17	WASHER, (.2656 x .625 x .0625) Stainless Steel	12-35462
18	NUT, (.250-28) Stainless Steel	11-826709109	11-33825, 11-35045
19	SCREW, (.312-18 x .880) Stainless Steel	10-28782
20	GUIDE BLOCK	814284
21	SPRING	24-20099
22	LINK ROD ASSEMBLY	67073A1
23	SHIFT SHAFT ASSEMBLY Comment: (LONG)	79932A16
23	SHIFT SHAFT ASSEMBLY Comment: (X-LONG)	79932A17
24	NOT SOLD SEPARATE, Roll Pin	NSS
25	NOT SOLD SEPARATE, Shift Shaft Lever-Upper	NSS
26	BUSHING	23-26856
27	WAVE WASHER	13-29720
28	WASHER, (.2656 x .625 x .0625) Stainless Steel	12-35462
29	NUT, (.250-28) Stainless Steel	11-826709109	11-33825, 11-35045
30	SWITCH	87-8M0207794
31	SCREW, (#6-32 x .875)	10-77478
32	WASHER	12-27882
33	BUSHING	23-8M0215006
34	ROD	8508152
35	CAM	8562211
36	BUSHING	23-856895	23-883392
37	BEARING	30-856896	30-856896 1
38	SCREW, (M8 x 40)	10-81893440
39	LEVER/ROLLER KIT, Throttle	850286A03
40	ROLLER	8M0072162	889610, 840968
41	WASHER, (.203 x .500 x .032)	12-8M0204666
42	NUT, Stainless Steel	8-32,11-826709104	11-846115
43	SCREW, (M5 x 18)	10-8M0027821
44	WASHER, Spool	12-8M0027820
45	LOCKWASHER, External	10,13-69432
46	WASHER, Cupped	12-8M0027819

Tools

Below is the parts list for Mercury 175 PROXS (2.5L) Tools:

Position No.	Part Name	OEM Number	Supersedes
-	HARNESS ASSEMBLY, DDT Adaptor, Electrical/Ignition	84-822560A5
-	HOLDER TOOL	91-52344
-	PULLER ASSEMBLY	91-849154T1
-	CABLE ASSEMBLY, DDT, Ignition	84-825003A1
-	MULTI METER, Electrical/Ignition	91-99750A1
-	SWITCH ASSEMBLY, Electrical/Ignition	91-52024A1
-	SERVICE TACHOMETER, Electrical/Ignition	91-59339
-	TESTER, Eight Chamber, Electrical/Ignition	91-850439T1
-	GAP TOOL, Single Chamber, Electrical/Ignition	91-63998A1
-	TACH INTERFACE MODULE, Electrical/Ignition	91-825824A2
-	TIMING LIGHT, Electrical/Ignition	91-99379
-	ALIGNMENT TOOL, Trim/Tilt System	91-112301
-	MULTI METER, Trim/Tilt System	91-99750A1
-	TEST GAUGE KIT	91-52915A6
-	SPANNER WRENCH, Trim/Tilt System	91-74951
-	HEAT LAMP, Trim/Tilt System	91-63209
-	REMOVER TOOL, Trim Rod Guide, Trim/Tilt System	91-44487T1
-	REMOVAL TOOL, Trim Rod, Trim/Tilt System	91-44486A1
-	SLEEVE, Powerhead	91-55919
-	LIFTING EYE (Powerhead)	91-904551
-	INSTALLER KIT, Powerhead	91-77109A3
-	REMOVAL TOOL, Piston Pin Lock Ring, Powerhead	91-52952T1
-	EXPANDER TOOL, Piston Ring, Powerhead	91-24697
-	MANDREL TOOL, Piston Pin, Powerhead	91-92973A1
-	STAND TOOL, Powerhead	91-30591T1
-	CAP TOOL, Flywheel Puller, Powerhead	91-24161
-	COMPRESSOR TOOL, Piston Ring (3.50), Powerhead	91-818773T	91-818773
-	TORQUE WRENCH, (0-150 lb-in), Powerhead	91-66274
-	PULLER PLATE, Powerhead	91-37241
-	GAUGE, DFI	91-881834A1
-	SIZING TOOL, DFI	91-8519802
-	CAP, Installation, DFI	91-8519803
-	GAUGE KIT, Air/Fuel Pressure, DFI	91-881833A03	91-881833A 2
-	INDICATOR TOOL, Backlash, Gear Housing	91-8M0053505	91-78473
-	INDICATOR TOOL, Backlash, Gear Housing	91-196601
-	MANDREL, Bearing Driver Cup, Gear Housing	91-31106T
-	DRIVER TOOL, Bearing Cup, Gear Housing	91-87120T
-	INSTALLATION TOOL, Bearing, Gear Housing	91-18601
-	TOOL, Preload, Gear Housing	91-14311A04
-	PULLER KIT, Bearing, Gear Housing	91-31229A7
-	MANDREL, Gear Housing	91-15755T
-	DRIVE HEAD TOOL, Gear Housing	91-36569T
-	DRIVER ROD TOOL, Needle Bearings, Gear Housing	91-37323
-	WRENCH TOOL, Driveshaft Bearing, Gear Housing	91-36571T
-	INSTALLER TOOL, Bearing, Gear Housing	91-38628T
-	NUT, (.625-18), Gear Housing	11-24156
-	PLATE, Gear Housing	91-29310
-	WASHER, Gear Housing	12-34961
-	RETAINING TOOL, Bearing, Gear Housing	91-43506T
-	HOLDING TOOL, Dial Indicator, Gear Housing	91-89897
-	TOOL, Cover Nut, Gear Housing	91-73688
-	INSTALL TOOL, Cross Pin, Gear Housing	91-86642
-	DIAL INDICATOR TOOL, Gear Housing	91-58222A1
-	FOWARD GEAR INSTALLATION TOOL, Gear Housing	91-815850
-	INSTALLER TOOL, Needle Bearing - Forward Gear, Gear Housing	91-86943T
-	NUT TOOL, Gear Housing Cover, Gear Housing	91-61069T
-	GUIDE PLATE, Gear Housing	91-816243
-	PULLER JAWS, Gear Housing	91-816242
-	WASHER, Gear Housing	12-37429
-	MANDREL, Gear Housing	91-92788T
-	DRIVER, Oil Seal, Gear Housing	91-31108T
-	TOOL, Pinion Locating, Gear Housing	91-12349A05
-	LOCATION TOOL, Pinion Gear, Gear Housing	91-74776T
-	PROPELLER SHAFT, Gear Housing	44-93003
-	INSTALLER TOOL, Bearing, Gear Housing	91-816292
-	PULLER TOOL, Gear Housing	91-85716
-	PULLER JAW ASSEMBLY, Gear Housing	91-46086A1
-	PULLER PLATE, Gear Housing	91-37241
-	INSTALLATION TOOL, Bearing Adaptor, Gear Housing	91-18605A2
-	PULLER ASSEMBLY, Slide Hammer, Gear Housing	91-34569A1
-	REMOVAL/INSTALL TOOL, Shift Shaft Bushing, Gear Housing	91-31107T
-	TORQUE WRENCH, (0-150 lb-in), Gear Housing	91-66274
-	TEST TOOL, Direct Injector	91-899883A08
-	PARTS MANUAL, 150 Pro XS (2.5L)	90-8M0047641

Top Cowl

Below is the parts list for Mercury 175 PROXS (2.5L) Top Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	TOP COWL ASSEMBLY (Includes all Decals except Horsepower) Comment: SN# 1B934544 & Below	100-883013T03
1	TOP COWL ASSEMBLY (Includes all Decals except Horsepower) Comment: SN# 1B934545 & Up	100-8M0083588	100-8M0070603 SN# 1B934545 & Up
2	SCREW, (M6 x 20)	10-82130020
3	SOUND BLANKET KIT	883019A02	883019A 1
4	NOT SOLD SEPARATE, Sound Blanket-Port	NSS
5	NOT SOLD SEPARATE, Sound Blanket-Starboard	NSS
6	NOT SOLD SEPARATE, Sound Blanket-Rear	NSS
7	HANDLE KIT, Cowl Latch	831207A16	831207A14, 831207T 3, 831207T10
8	BUSHING	23-812707	23-71984, 23-F286818, 23-F286828, F480818
9	SPACER	23-8312141
10	WASHER, (.520 x .850 x .060) Nylon - Black	12-8M0042643	12-19605
11	WASHER, Wave	13-12134
12	CAM	8M0001081	889566, F481777, F48177
13	WASHER	12-8M0214930
14	SCREW, (M6 x 16 MM) Stainless Steel	10-8M0103805	10-885525 16
15	BRACKET, Front	8M0036792	821249M 2
16	BUMPER, Latch	815477
17	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
18	NUT, (M6) Stainless Steel	11-401366
19	RING, Retaining	53-8237951
20	ROLLER	8M0207770
21	PIN, Roll	8155381
22	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
23	NOT SOLD SEPARATE, Decal-Counter Rotation	NSS
24	NOT SOLD SEPARATE, Decal-Break-In	NSS
-	DECAL SET, ProXS, HP decal not included Comment: SN# 1B934544 & Below	37-897136A07
-	DECAL SET, ProXS, HP Decal not included Comment: SN# 1B934545 & Up	37-8M0083587	37-8M0073124 SN# 1B934545 & Up
-	DECAL, Horsepower (175) Comment: SN# 1B934544 & Below	37-8M0061184	37-892565004 SN# 1B934544 & Below
-	DECAL, Horsepower (175) Comment: SN# 1B934545 & Up	37-8M0065745

Transom Brackets

Below is the parts list for Mercury 175 PROXS (2.5L) Transom Brackets:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET ASSEMBLY, Transom-Starboard	3426-828334T03
2	BRACKET ASSEMBLY, Transom-Port	3425-828333T08
3	FITTING, Grease, Port	22-8M0169588
4	TILT TUBE	826125A1
5	NUT, (1.00-14) Nylon Insert	11-826135
6	O-RING, (.612 x .103)	25-45711
7	WASHER	13-88750
8	NUT, (.875-14)	11-826164
9	SCREW, (.500-20 x 4.500)	10-8M0149747
9	SCREW, (.500-20 x 5 Inches)	10-8M0204730
10	WASHER, (.530 x .870 x .105) Stainless Steel	12-8M0204665
11	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
12	NUT, (.500-20)	11-82671117
13	LEVER ASSEMBLY, Tilt Lock	8M0115104	8M0115103, 99629T 2
14	SPRING, Tension	24-830899
15	NYLINER	23-65830
16	SPRING, Compression	24-830900
17	KNOB	99633
18	PIN, Groove	17-99615
19	PIN	17-893709	17-99617
20	DECAL, Warning	37-8M0043059

Vapor Separator Components

Below is the parts list for Mercury 175 PROXS (2.5L) Vapor Separator Components:

Position No.	Part Name	OEM Number	Supersedes
-	VAPOR SEPARATOR ASSEMBLY, Complete	859174T06
1	COVER KIT	8M6004919
2	FITTING	22-8554246
3	FITTING, Straight	22-881740
4	PLUG	19-883208	19-881830
5	GASKET	27-883252
6	SEAL, Pump	26-803878
7	SCREW AND WASHER, (#8-32 x .750)	1395-808612	1399-5132
8	FITTING KIT	22-885186A1
9	O-RING, (.468 x .078)	25-831985	25-885187
10	WIRE ASSEMBLY	84-881831
11	PUMP KIT	855427A1
12	SLEEVE	8M6000589	23-855428
13	FLOAT KIT	8M6004920
14	SHAFT	F10064
15	VALVE, Needle	8M6004917
16	SCREW, (M6 x 16)	10-883223
17	SEAT/VALVE	8M6004918
18	BAFFLE, Fuel	889318002	883260
19	SCREW, (M6 x 16)	10-883223
20	FILTER KIT	35-18458T4
21	PROBE	8M0204710
22	BOWL KIT	855434T04
23	FITTING KIT	22-880862A1
24	O-RING	25-880863
25	PLUG KIT	19-855435A1
26	O-RING	25-8M0062785	25-883209
27	SEAL, Pump	26-8554331
28	ELBOW	22-8554245
29	PUMP ASSEMBLY	8M0047624	855843 2
30	ELBOW	22-855802A1
31	O-RING	25-883551
32	BRACKET KIT	855756A1
33	SCREW, (M6 x 16)	10-1993716
34	TIE STRAP, (11.750 Inches)	54-850181
35	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
36	GROMMET	25-856928
37	FITTING KIT	22-880862A1
38	O-RING	25-880863
39	SCREW, (M6 x 10)	10-82130010

Visual Warning Kit, 17334A2

Below is the parts list for Mercury 175 PROXS (2.5L) Visual Warning Kit, 17334A2:

Position No.	Part Name	OEM Number
1	VISUAL WARNING SYSTEM	17334A2
2	LAMP	88-17429
3	BRACKET, Switch Mounting	76424
4	STUD, (#10-32 x 2.00)	16-55422
5	WASHER, (.200 x .440 x .032)	12-24676
6	NUT, Stainless Steel	10-32,11-68219
NS	SCREW, (#10-32 x .250)	10-24231
NS	NUT AND LOCKWASHER,	10-32,11-27164

Water Hoses

Below is the parts list for Mercury 175 PROXS (2.5L) Water Hoses:

Position No.	Part Name	OEM Number	Supersedes
1	PLUG, (.500-14)	22-883048
2	FITTING, (.250-18 x .62) Brass	22-36382
3	FITTING	22-883089
4	FITTING, (.250-18) 90 Degree - Brass	22-687271
5	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
6	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
7	HOSE, (48.00 Inches Bulk) (Cut to 21 Inches)	32-774572
8	STRAINER	35-8348084
9	HOSE, Water - Molded - Starboard	32-8M0022492
10	HOSE, Water - Molded - Port	32-8M0022447
11	FITTING	22-291112
12	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
13	TUBING, (32.00 Inches Bulk) (Cut to 18-1/2 Inches)	32-83476463
14	FITTING	22-881866	22-859432
15	TUBING, (52.00 Inches Bulk) (Cut to 15 Inches)	32-85978571
16	FITTING	22-8M0207782
17	SENSOR KIT, (0-50 PSI) (TAN)	71-8M0157742
18	CLIP, (.865)	54-883066
19	TEE, Fitting	22-875207
20	TUBING, (52.00 Inches Bulk) (Cut to 44 Inches)	32-85978571
21	COUPLER	22-8M0214971
22	PLUG	22-859732
23	FITTING, Adapter	22-8M0214970
24	TUBING, (52.00 Inches Bulk) (Cut to 5 Inches)	32-85978571
-	LONG BLOCK ASSEMBLY	879809A08

Download this page as PDF: Click here

For Mercury Owners:

To assist you in maintaining and repairing your marine engines, we hope the following resources may be of use:

Mercury / Mercruiser / Mariner Parts from JLM Marine

About JLM Marine

Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.

As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.

We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.