Mercury 115 EFI (4-STROKE) (0T801000 THRU 1B226999) Outboard Motor Parts Diagram & Catalog – Free PDF Download

by JLM Marine 30 Apr 2025 0 Comments

Mercury 115 EFI (4-STROKE) Outboard Motor Parts Diagram & Catalog – Free PDF Download

Accessories

Below is the parts list for Mercury 115 EFI (4-STROKE) Accessories:

Part Name	OEM Number	Supersedes
FLUSH KIT, Coastal	858566A02
SENSOR KIT, Pitot	881879A22	881879A12
HOSE ASSEMBLY, Water Pressure	32-892156A01
SENDER KIT, Trim Comment: (DIGITAL)	891777A01
SENDER KIT, Power Trim Comment: (ANALOG)	821400A2
TANK ASSEMBLY, Oil	1257-8742A25
HARNESS ASSEMBLY, Digital Adaptor	84-859244T1
SWITCH KIT, Tilt Limit	87-887979A2
STEERING HANDLE KIT, Tiller	896648A07	896648A04, 896648A01
ADAPTOR	22-86306A01
SENDER KIT, Power Trim	821400A2
ATTACHING KIT, Steering Comment: (SINGLE)	92876A8
EXTENSION KIT, Dual Engine Comment: (DUAL)	92876A9
TACH MODULE KIT	56-883040A1

Air Compressor

Below is the parts list for Mercury 115 EFI (4-STROKE) Air Compressor:

Position No.	Part Name	OEM Number	Supersedes
1	COMPRESSOR ASSEMBLY, Air	8M0050654	8M0048123, 854333T11, 854333T07
2	END CAP	8M0114192
3	O-RING	25-86391
4	CONNECTING ROD ASSEMBLY	657-853658T02
5	NOT SOLD SEPARATE, Piston Assy. (With Rings)	NSS
6	LOCK RING	53-854638
7	REED PLATE ASSEMBLY	853584A10
8	GASKET	27-854442
9	GASKET	27-854443
10	HEAD, Compressor	854334T02
11	FITTING, (.375-18)	22-38565
12	SCREW, (M8 x 35)	10-82446035
13	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
14	FITTING	22-856744	22-856744 1
15	O-RING, (.468 x .078)	25-831985	25-885187
16	SENSOR ASSEMBLY	8M0148668
17	O-RING, (.351 x .072)	25-896699	25-888814
18	CHECK VALVE	21-888421
19	PIN, Special	8215832
20	FITTING	22-15133
21	TIE STRAP, (5.50 Inches)	8M0214940
22	HOSE, (.125 x 25.00 Inches)	32-88306955
23	CONNECTOR	21-889851
24	SCREW, (M6 x 25)	10-82130025
25	PULLEY	853944T03	853944T01
26	SCREW, (M6 x 12)	10-85593912
27	TENSIONER ARM	8M0047394	854799001
28	PULLEY	8547971
29	SCREW, (M10 x 25) Hex Flange - Stainless Steel	10-4010825
30	BEARING, Flanged	30-8570111
31	BUSHING	23-856549001
32	TUBING, (18.00 Inches Bulk), Cut to 8 Inches	32-88104441
33	SPRING	24-8547953
34	SCREW, (M10 x 60)	10-4000382
35	TUBING, (18.00 Inches Bulk), Cut to 13 Inches	32-88104441
36	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
37	SCREW, (M8 x 90)	10-82446090

Air Hoses

Below is the parts list for Mercury 115 EFI (4-STROKE) Air Hoses:

Position No.	Part Name	OEM Number	Supersedes
1	HOSE, (32.00 Inches) (Cut to 8 Inches	32-85525884
2	CLAMP, Hose (15.3)	54-8M0214964
3	HOSE, Air	32-885376
4	HOSE ASSEMBLY, Air By-Pass	32-881041A1
5	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
6	MUFFLER, Air	881197
7	HOSE, (17.00 Inches Bulk) (Cut to 4-1/2 Inches	32-85833939

Bleed System

Below is the parts list for Mercury 115 EFI (4-STROKE) Bleed System:

Position No.	Part Name	OEM Number	Supersedes
1	FITTING, Tee	22-59169003
2	TUBING, (38.00 Inches Bulk) (Cut to 3-1/4 Inches)	32-8M0054152	32-856060 65
3	TUBING, (38.00 Inches Bulk) (Cut to 3-1/4 Inches)	32-8M0054152	32-856060 65
4	TUBING, (38.00 Inches Bulk) (Cut to 19 Inches)	32-8M0054152	32-856060 65
0	POWERHEAD ASSEMBLY Comment: 75	895233A07	895233A05 75
0	POWERHEAD ASSEMBLY Comment: 90/115	891767A07	891767A04 90/115

Bottom Cowl

Below is the parts list for Mercury 115 EFI (4-STROKE) Bottom Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	BOTTOM COWL, Starboard Comment: SN# 0T979999 & Below	100-880775A03	100-880775A00 SN# 0T979999 & Below
1	BOTTOM COWL, Starboard Comment: SN# 0T980000 & Up	100-880775A03	100-880775A00 SN# 0T980000 & Up
2	SEAL, Cowl (41.00 Inches)	8M0109217	8M0043272, 825318 1
3	NOT SOLD SEPARATE, Sound Blanket (Part of 889720A00)	NSS
4	BOTTOM COWL, Port Comment: SN# 0T979999 & Below	100-880774A03	100-880774A02 SN# 0T979999 & Below
4	BOTTOM COWL, Port Comment: SN# 0T980000 & Up	100-880774A03	100-880774A02 SN# 0T980000 & Up
5	SEAL, Cowl (41.00 Inches)	8M0109217	8M0043272, 825318 1
6	SOUND BLANKET KIT Comment: (PORT)	889720A00
7	PIN	17-885116
8	LEVER, Cowl Latch	880783T
9	BUSHING	23-335891
10	FITTING, Vent Comment: SN# 0T979999 & Below	22-889684002	22-889684001 SN# 0T979999 & Below
10	FITTING, Vent Comment: SN# 0T980000 & Up	22-889684002	22-889684001 SN# 0T980000 & Up
11	CAM, Latch	884468
12	WASHER, (.265 x .750 x .048) Stainless Steel	12-65567
13	SCREW, (M6 x 16)	10-1993716
14	RETAINER	822363T1
15	SCREW, (M6 x 16)	10-82130016
16	CHECK VALVE ASSEMBLY, Drain	21-817519A2
17	SPRING Comment: SN# 0T979999 & Below	24-892166001	24-892166 SN# 0T979999 & Below
17	SPRING Comment: SN# 0T980000 & Up	24-892166001	24-892166 SN# 0T980000 & Up
18	SCREW, (M6 x 40)	10-82130040
19	BRACKET, Cable Retainer	19812T03
20	LATCH	98889
21	DRIVE SCREW	10-42975
22	CUP	39519
23	SCREW, (M8 x 50) Stainless Steel	10-40011154
24	NUT, (M8)	11-401388
25	WASHER	12-817274	12-817274 1
26	STUD	16-8M0034456	16-42917 2
27	GROMMET Comment: SN# 0T979999 & Below	25-855362001	25-855362 SN# 0T979999 & Below
27	GROMMET Comment: SN# 0T980000 & Up	25-855362001	25-855362 SN# 0T980000 & Up
28	BUSHING	23-855364
29	SEAL, Lower Cowl (44.75 Inches)	8M0043167	8M0036668, 884256 4
30	SWITCH, Trim	87-8M0235191
31	FITTING	22-94848
32	RETAINER, Cable	888508
33	BOOT, Idle Relief	884464
34	CLAMP, Upper	8M0000504	884465001, 884465
35	CLAMP, Lower	8M0000484	884466, 896637
36	SCREW, (M6 x 16)	10-82130016
37	FOAM	859343
38	TIE STRAP, (11.750 Inches)	54-850181
39	SPACER	23-892427
1	BOTTOM COWL ASSEMBLY Comment: (PORT)	100-878587A1
2	BOTTOM COWL ASSEMBLY Comment: (STARBOARD)	100-8M0113913
3	SEAL, Cowl (41.00 Inches)	8M0109217	8M0043272, 825318 1
4	INSERT	878547T
5	SCREW, (M6 x 40)	10-82130040
6	RETAINER	831209
7	BOOT, Idle Exhaust	858742
8	GROMMET	8M0039078	859251
9	FITTING	22-827948
10	WASHER	12-855576
11	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
12	HOSE, (32.00 Inches)	32-881535
13	HOSE, (57.00 Inches Bulk) (Cut to 5 IN.)	32-8M0108355	32-8M0047428, 32-830756109, 32-99127109, 32-877821
14	TUBING, (36.00 Inches Bulk) (Cut to 26 IN.)	32-9912688
15	TEE	22-817518
16	SCREW, (M6 x 20)	10-82130020
17	GROMMET	25-889724	858741 1, 858741 2
18	SWITCH ASSEMBLY	87-8M0042301	87-896620, 87-856990, 87-850691, 87-18286A40
19	FRONT HANDLE, Black Comment: CAST HANDLE	889740A02	821253F 1, 821253F 2, 821253F 4 CAST HANDLE
19	HANDLE KIT Comment: PLASTIC HANDLE	889740A02	821253F 1, 821253F 2, 821253F 4 PLASTIC HANDLE
20	SCREW, (M6 x 16) Comment: USE W/PLASTIC HANDLE	10-1993716
20	SCREW, (M6 x 75) Comment: USE W/CAST HANDLE	10-824868
21	BUSHING	23-33589
22	O-RING, (.614 x .070)	25-48462
23	PAWL	8219423
24	WASHER, (.281 x .734 x .063)	12-69057
25	NUT, (M6) Stainless Steel	11-401366
26	PLUG, Male	13541

Crankshaft, PISTONS AND CONNECTING RODS

Below is the parts list for Mercury 115 EFI (4-STROKE) Crankshaft, PISTONS AND CONNECTING RODS:

Position No.	Part Name	OEM Number	Supersedes
1	CRANKSHAFT	2406-880894T
2	SEAL, Oil	26-8040992
3	SEAL, Oil	26-8041002
4	BEARING Comment: (GREEN)	31-804101T
4	BEARING Comment: (BLUE)	31-804101T10
4	BEARING Comment: (RED)	31-804101T20
5	BEARING Comment: (YELLOW)	31-804102T
5	BEARING Comment: (GREEN)	31-804102T10
5	BEARING Comment: (BLUE)	31-804102T20
5	BEARING Comment: (RED)	31-804102T30
6	BEARING Comment: (GREEN)	31-804103T
6	BEARING Comment: (BLUE)	31-804103T10
6	BEARING Comment: (RED)	31-804103T20
7	PISTON ASSEMBLY Comment: (STANDARD)	2715-880895A14	2715-880895A05, 2715-880895T 1 (STANDARD)
7	PISTON ASSEMBLY Comment: (.25MM O/S)	2715-880895A16	2715-880895A12, 2715-880895T10 (.25MM O/S)
8	BOLT, (M8 x 38)	10-880896
9	RING SET, Piston Comment: (STANDARD)	39-880897T02	39-880897T 1 (STANDARD)
9	RING SET, Piston Comment: (.25 MM O/S)	39-880898T02	39-880898T 1 (.25 MM O/S)
10	BEARING Comment: (YELLOW)	31-880899T
10	BEARING Comment: (GREEN)	31-880899T10
10	BEARING Comment: (BLUE)	31-880899T20
10	BEARING Comment: (RED)	31-880899T30
-	POWERHEAD ASSEMBLY	881421T04	881421T02, 881421T01
-	GASKET SET, Powerhead	27-858732T02	27-858732T01

Crankshaft, Pistons and Connecting Rods

Below is the parts list for Mercury 115 EFI (4-STROKE) Crankshaft, Pistons and Connecting Rods:

Position No.	Part Name	OEM Number	Supersedes
1	CRANKSHAFT ASSEMBLY	400-879633T01
2	RING, Retaining	53-880119
3	BEARING, Ball (LOWER)	30-43011T
4	KEY, Woodruff	28-91800
5	WEAR SLEEVE	786611
6	O-RING, (.859 x .139)	25-35126
7	RING, Seal	39-8M0071643	39-879850
8	BEARING	31-879848A02	879848A01
9	NOT SOLD SEPARATE, Needle Bearing	NSS
10	PISTON ASSEMBLY Comment: (Standard)	700-879858T08	700-879858T03 (Standard)
10	PISTON ASSEMBLY Comment: (.015 Oversize)	700-896961A02
10	PISTON ASSEMBLY Comment: (.030 Oversize)	700-896962A02
11	NOT SOLD SEPARATE, Piston Pin	NSS
12	RING	40-841202
13	RING SET, Piston Comment: (Standard)	39-827179A12	39-815958A12 (Standard)
13	RING SET, Piston Comment: (.015 Oversize)	39-875252A12	39-856939A12, 39-826293A12 (.015 Oversize)
13	RING SET, Piston Comment: (.030 Oversize)	39-875257A12	39-826297A12, 39-856940A12 (.030 Oversize)
14	CONNECTING ROD ASSEMBLY Comment: SN# 0T845718 & Below	600-888470T05
14	CONNECTING ROD ASSEMBLY Comment: SN# 0T845719 THRU 1B189548	600-888470T08
14	CONNECTING ROD ASSEMBLY Comment: SN# 1B189549 & Up	600-888470T06
15	THRUST WASHER	12-88263
16	BEARING, Needle	29-8M0204715
17	SCREW, (.375-24 x 1.250)	10-94320
18	BEARING ASSEMBLY Comment: SN# 1B189548 & Below	31-892287A01
18	BEARING/CAGE KIT Comment: SN# 1B189549 & Up	31-844338A01	31-43012A04 SN# 1B189549 & Up
19	NOT SOLD SEPARATE, Roller Bearing	NSS
20	BEARING ASSEMBLY, Roller (UPPER)	31-879853A01
21	SEAL, Oil	26-879635
0	GASKET SET, Powerhead	27-879855A04
0	POWERHEAD ASSEMBLY Comment: (75)	895233A07	895233A05 (75)
0	POWERHEAD ASSEMBLY Comment: (90/115)	891767A07	891767A04 (90/115)

Cylinder Block

Below is the parts list for Mercury 115 EFI (4-STROKE) Cylinder Block:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER BLOCK	892-881422T05	892-881422T 1
2	PIN, Dowel	17-82364M
3	GASKET	27-858732002	27-858732 1
4	BOLT, (M8 x 55) Comment: SN# 0T979999 & Below	10-8M0101617
4	BOLT, (M8 x 55) Comment: SN# 0T980000 & Up	10-8M0101617
5	BOLT, (M10 x 135)	10-804072
6	GROMMET	25-855690
7	LIFTING EYE	804073
8	BOLT, (M6 x 20)	10-8257021
9	PLUG, (M14 x 12)	19-825953
10	GASKET	27-81990M
11	FILTER, Oil	35-8M0162830
12	BOLT	10-804097
13	COVER, Outer Exhaust	881424T02	881424T, 881424T01
14	GASKET	27-804076003	27-804076, 27-804076001
15	BOLT, (M6 x 30)	10-881427
16	SCREW	10-881425
17	GASKET	27-881426
18	NOT SOLD SEPARATE, Anode Comment: Order Cover	NSS
19	GROMMET	25-804086
20	COVER	804085
21	BOLT, (M6 x 20)	10-8524741
22	BOLT, (M8 x 25)	10-827207
23	GROMMET	25-804082
24	VALVE, Pressure Control	804080001	804080
25	SPRING	24-804081
26	GASKET	27-804084
27	COVER	804083001	804083
28	BOLT, (M6 x 16)	10-881428
29	CLIP	54-804089
30	HOSE	32-804088
31	TIE STRAP, (4.00 Inches)	56762
32	STUD	16-8587331
33	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963
34	NUT, (M10)	11-40140
35	SCREW, (M8 x 35)	10-81893435
36	CAP, Rubber	881600
-	GASKET SET, Powerhead	27-858732T02	27-858732T01
-	POWERHEAD ASSEMBLY	881421T04	881421T02, 881421T01

Cylinder Block and Crankcase

Below is the parts list for Mercury 115 EFI (4-STROKE) Cylinder Block and Crankcase:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER BLOCK Comment: (75)	800-878581A20
1	CYLINDER BLOCK Comment: (90/115)	800-878581A09
2	PIN, Dowel - Without Hole (.375 x .625)	17-43044
3	PIN, Center Main	17-8M0036405	17-67296
4	SCREW, (M10 x 80)	10-4009680
5	BRACKET	8M0111325
6	SCREW, (M8 x 40)	10-81742740
7	FITTING, (.250-18 x .62) Brass	22-36382
8	PLUG, Pipe (.375-18)	22-185981
9	SCREW, (M8 x 35)	10-82127335
10	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
11	CHECK VALVE	21-883139001
12	CHECK VALVE	21-889830
13	FITTING, Elbow 45 Degree (1.25)	22-782792
14	CHECK VALVE	21-8282182
15	DEFLECTOR, Water	8248576
16	PLUG, Pipe (.375-18)	22-185981
17	FITTING	22-881866	22-859432
18	STUD, (M10 x 136)	16-892561001	16-889607
19	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963
20	NUT, (M10)	11-40140
21	CHECK VALVE, 90 Degree (.0625-27)	21-8592352
22	SEAL	891956
23	PLUG, Pipe (.375-18) Brass	22-8M0180565
24	SCREW, (M8 x 20)	10-81742720
25	SENSOR, Crank Position	8M0082988	8M0030022, 828358 2
26	SCREW, (M5 x 16) Stainless Steel	10-40011107
27	COVER, Flywheel	880198T
28	GROMMET Comment: SN# 0T931540 & Below	25-8M0153609
28	GROMMET Comment: SN# 0T931541 & Up	25-8M0153609
29	COUPLING INSERT	22-857175	22-861405
30	COUPLING BODY	22-857176
31	CAP	19-858240	861427
32	TUBING, (.312) (70.00 Inches Bulk) (Cut to 43 Inches)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
33	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
34	FITTING	22-835454001
35	BRACKET, Oil Reservoir	880731002
0	GASKET SET, Powerhead	27-879855A04
0	POWERHEAD ASSEMBLY Comment: 75	895233A07	895233A05 75
0	POWERHEAD ASSEMBLY Comment: 90/115	891767A07	891767A04 90/115

Cylinder Head

Below is the parts list for Mercury 115 EFI (4-STROKE) Cylinder Head:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER HEAD ASSEMBLY	881310T08
2	PIN, Guide	17-804110
3	PLUG	19-804111
4	BOLT, (M7 x 48)	10-804112
5	PIN, Dowel	17-804113
6	BOLT, (M7 x 37)	10-804114
7	BOLT, (M10 x 145)	10-881311	10-804117
8	COLLAR	23-8M0070515	23-804116
9	GASKET	27-8041151
10	BOLT	10-83124714
11	WASHER, Sealing	12-831246
12	BOLT, (M8 x 55)	10-881312
13	NOT SOLD SEPARATE, Anode Comment: Order Cover	NSS
14	GROMMET	25-804086
15	COVER	804085
16	BOLT, (M6 x 20)	10-8524741
17	BOLT, (M8 x 25)	10-827207
18	SPARK PLUG	33-881284Q	33-881284
19	THERMOSTAT	881429
20	THERMOSTAT COVER	8041271
21	SCREW, (M6 x 25 MM)	10-8248326
22	COVER KIT	881313T1
23	COVER, Breather	804119
24	SCREW, (M4 x 8)	10-804120
25	GASKET	27-804123
26	GROMMET	25-855690
27	BOLT, (M6 x 30)	10-858530	10-879194068
28	PLUG ASSEMBLY, Oil	859578A1
29	NOT SOLD SEPARATE, O Ring	NSS
30	COVER	858752001	858752
31	SCREW, (M6 x 16)	10-1993716
-	GASKET SET, Powerhead	27-858732T02	27-858732T01
-	CYLINDER HEAD ASSEMBLY	881310T09	881310T05, 881310T 1
-	POWERHEAD ASSEMBLY	881421T04	881421T02, 881421T01

Driveshaft Housing

Below is the parts list for Mercury 115 EFI (4-STROKE) Driveshaft Housing:

Position No.	Part Name	OEM Number	Supersedes
1	HOUSING ASSEMBLY, Driveshaft	1598-881913T01
2	STUD, (M10 x 100) Comment: (LONG)	16-903501
2	STUD, (M10 x 227) Comment: (X-LONG)	16-9035015
3	STUD, (M10 x 63) Comment: (LONG)	16-9035012
3	STUD, (M10 x 190) Comment: (X-LONG)	16-8M0034462	16-90350 16 (X-LONG)
4	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963
5	NUT, (M10)	11-40140
6	PICKUP ASSEMBLY, Speedometer	22-85822A4
7	CONNECTOR, 90 Degree (.125-27) Nylon	22-433351
8	CONNECTOR, Straight	22-85822T
9	MOUNT	881916
10	BOLT, (M12 x 154)	10-898835001	10-42973
11	WASHER, (.875 Inch Outside Diameter)	12-30119
12	NUT, (M12)	11-8M0204662
13	CABLE ASSEMBLY, Ground, To Swivel Bracket	88238A10
14	SCREW, (.250-20 x .500) Stainless Steel	10-41508
15	CLAMP	8M0036786	881917
16	NUT	11-35521
17	SCREW, (M8 x 25)	10-889833025
18	COVER	100-8M4500754	8M0000852, 882752
19	SCREW, (#12-24 x .620)	10-88417
20	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
21	WASHER, Neoprene	12-881976
22	SPACER KIT Comment: (X-LONG)	12092A3
23	PIN, Dowel - With Hole (.375 x .625) Comment: (FRONT)(W/HOLE)(X-LONG)	17-8M0084244	17-43043 (FRONT)(W/HOLE)(X-LONG)
23	PIN, Dowel - Without Hole (.375 x .625) Comment: REAR)(X-LONG)	17-43044
24	PLATE WASHER	892214
1	HOUSING ASSEMBLY, Driveshaft	1507-858576T2
2	STUD, (M10 x 100) Comment: (LONG)	16-903501
2	STUD, (M10 x 227) Comment: (X-LONG)	16-9035015
3	STUD, (M10 x 63) Comment: (LONG)	16-9035012
3	STUD, (M10 x 190) Comment: (X-LONG)	16-8M0034462	16-90350 16 (X-LONG)
4	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963
5	NUT, (M10)	11-40140
6	PICKUP ASSEMBLY, Speedometer	22-85822A15
7	CONNECTOR, 90 Degree (.125-27) Nylon	22-433351
8	CONNECTOR, Straight	22-85822T
9	MOUNT	44343T1
10	BOLT, (M12 x 154)	10-898835001	10-42973
11	WASHER, (.875 Inch Outside Diameter)	12-30119
12	NUT, (M12)	11-8M0204662
13	CABLE ASSEMBLY, Ground	88238A10
14	SCREW, (.250-20 x .500) Stainless Steel	10-41508
15	CLAMP	858916T
16	SCREW, (M8 x 25)	10-4010725
17	CAP	8M0142713
18	BUSHING	23-859550
19	PIN, Alignment	17-24873
20	FITTING	22-855622
21	SPACER KIT Comment: (X-LONG)	12092A3
22	PIN, Dowel - With Hole (.375 x .625) Comment: (W/HOLE)(X-LONG)	17-8M0084244	17-43043 (W/HOLE)(X-LONG)
22	PIN, Dowel - Without Hole (.375 x .625) Comment: (X-LONG)	17-43044
23	SPACER Comment: (X-LONG)	23-813745	23-43041 (X-LONG)
24	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275

Electrical Components

Below is the parts list for Mercury 115 EFI (4-STROKE) Electrical Components:

Position No.	Part Name	OEM Number	Supersedes
1	PLATE, Electrical	880190T03
2	COIL, Ignition	300-8M0077471	300-879984T01, 339-879984A 1, 339-879984T00
3	LEAD, Hi Tension	84-884442T03	84-884442 3
4	SPARK PLUG, NGK#IZFR5J	33-892567Q	33-892567001
5	SCREW, (M6 x 30)	10-82129130
6	CLIP	828791
7	SCREW, (M6 x 12)	10-82130012
8	SENSOR KIT, (0-50 PSI)	71-8M0157742
9	CLIP, (.865)	54-883066
10	FITTING Comment: SN# 0T979999 & Below	22-8M0207782
10	FITTING Comment: SN# 0T980000 & Up	22-8M0207782
11	TUBING, (52.00 Inches Bulk), Cut to 6 Inches	32-85978571
12	SCREW, (M6 x 14)	10-82129114
13	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
14	CABLE ASSEMBLY, Braided	84-858414A1
15	CLIP, (1.00)	54-858755
16	PCM, Propulsion Control Module Comment: (75)	89790640T	88555701S (75)
16	PCM, Propulsion Control Module Comment: (90) SN# 0T979999 & Below	89790641T	88555746S, 88555736S, 88555702S (90) SN# 0T979999 & Below
16	PCM, Propulsion Control Module Comment: (90) SN# 0T980000 & Up	89790641T	88555746S, 88555736S, 88555702S (90) SN# 0T980000 & Up
16	PCM, Propulsion Control Module Comment: (115) SN# 0T979999 & Below	89790642T	88555747S, 88555734S, 88555726S, 88555703S (115) SN# 0T979999 & Below
16	PCM, Propulsion Control Module Comment: (115) SN# 0T980000 & Up	89790642T	88555747S, 88555734S, 88555726S, 88555703S (115) SN# 0T980000 & Up
17	SCREW, (M6 x 25)	10-82129125
18	WASHER, (.265 x .750 x .048) Stainless Steel	12-65567
19	GROMMET	25-8M0190980
20	BUSHING	23-856954
21	RELAY ASSEMBLY	8M0207773
22	BRACKET	828102
23	GROMMET	25-818967
24	BUSHING	23-8M0214955
25	PIN, Special	8215832
26	SPACER Comment: SN# 0T979999 & Below	889600	889600F10 SN# 0T979999 & Below
26	SPACER Comment: SN# 0T980000 & Up	889600	889600F10 SN# 0T980000 & Up
27	NUT, (M6)	11-401376
28	CLIP, (.625)	54-858954
29	SOLENOID ASSEMBLY, (#10-32 / .3125-18 Terminals)	89-817109A2
30	GROMMET	25-822179
31	BUSHING	23-8M0214955
32	NUT, Brass	10-32,11-45076
33	CAP NUT,	10-32,11-813938
34	CABLE ASSEMBLY, Yellow/Red	84-883726A1
35	LOCKWASHER, (.312)	13-53166
36	NUT, (.312-18)	11-8M0204668
37	CABLE ASSEMBLY, (4.00 Inches) Black	84-88807A16
38	BOOT, Insulator - Yellow	85-8500673
39	HARNESS ASSEMBLY, Trim	84-819514T18
40	HARNESS ASSEMBLY, Fuse - 100 Ampere	84-878231A03
41	HARNESS ASSEMBLY, Starter	84-882829A03
42	BOOT, Insulator - Red	85-830233
43	HARNESS ASSEMBLY, Engine Wiring	84-880193T03
44	COVER, Fuse	858754
45	FUSE, Mini - Tan - 5 Ampere	88-832969T05	88-832969 5
46	FUSE, Mini - Yellow - 20 Ampere	88-832969T20	88-832969 20
47	CONNECTOR ASSEMBLY, 8 Pin	877613A1
48	CLIP	54-879962
49	CABLE ASSEMBLY, Battery - Positive	84-88439A25
50	BOOT, Insulator - Red	85-8500671
51	BUSHING	23-8502341
52	WASHER	12-4002318
53	SCREW, (M8 x 35)	10-82446035
54	GROMMET	25-833155
55	COVER	880192T01	880192T
56	GROMMET Comment: SN# 0T931540 & Below	25-8M0153609
56	GROMMET Comment: SN# 0T931541 & Up	25-8M0153609
57	CABLE ASSEMBLY, (12.00 Inches) Black	84-856583A07
58	SPACER	889992	889992F10
59	BRACKET	858953
60	TEE, Fitting	22-875207
61	TUBING, (52.00 Inches Bulk), Cut to 1-1/2 Inches	32-85978571
62	TUBING, (52.00 Inches Bulk), Cut to 52 Inches	32-85978571
63	COUPLER	22-8M0214971
64	PLUG	22-859732
1	COVER	881363T
2	BRACKET	881359T
3	HARNESS ASSEMBLY	84-881364T04	84-881364A04, 84-881364T 2
4	FUSE, 20 Ampere	88-832969T20	88-832969 20
5	FUSE, 30 Ampere	88-8M0057159	88-804291 10
6	COVER, Fuse Comment: (YELLOW)	891824010
6	COVER, Fuse Comment: (GREEN)	891824020
7	BRACKET	881362
8	SCREW	10-8813511
9	RELAY	881352T
10	WASHER	12-82214M
11	LOCKWASHER	13-82212M
12	SCREW	10-96671M
13	BOOT	85-804284001	85-804284
14	RELAY	881350T
15	SCREW	10-881351
16	CLAMP	54-881353
17	SCREW	10-8813511
18	CLAMP	54-881361
19	CLAMP	54-881360
20	BOLT, (M6 x 28)	10-804270
21	GROMMET	25-881304	25-93114M
22	BUSHING	23-804344003	23-82851M
23	BOLT, (M6 x 20)	10-804604
24	SCREW, (M6 x 16)	10-8248324
25	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
26	HARNESS ASSEMBLY, Adaptor Assy.-Remote	84-858740T4
27	TACH MODULE	8M0026570	17461A10
28	RETAINER	92753
29	CABLE ASSEMBLY, Positive - Battery	84-88439A33
30	CABLE ASSEMBLY, Negative - Battery	84-88439A10
31	NUT, (M8) Stainless Steel	11-401388
32	SCREW, (M6 x 20) Stainless Steel	10-8M0204741
33	HARNESS ASSEMBLY, Adaptor/Trim	84-858723T1
34	HARNESS ASSEMBLY, Trim Motor Adaptor	84-858914T1
35	CONNECTOR	859249T1
36	DECAL, Warning, High Voltage	37-8272822
37	DECAL, Caution-Start in Gear Comment: (Start In Gear)	37-881865	37-825064 (Start In Gear)
38	RELAY KIT, Trim	882751A3
39	HARNESS ASSEMBLY, Trim	84-826802A24
40	RELAY ASSEMBLY	8M0207773
41	GROMMET	25-818967
42	BUSHING	23-8M0214955
43	NOT SOLD SEPARATE, Decal	NSS
44	BRACKET	828102
45	SCREW, (M6 x 75)	10-824868
46	WASHER	12-8M0214930
47	BUSHING	23-823807	23-42806
48	PULLER, Fuse	804289

Engine Overhaul Gasket Set Components

Below is the parts list for Mercury 115 EFI (4-STROKE) Engine Overhaul Gasket Set Components:

Position No.	Part Name	OEM Number	Supersedes
-	GASKET SET, Powerhead	27-879855A04
0	DIAPHRAGM KIT, Fuel Pump	21-857005A1
0	NOT SOLD SEPARATE, Diaphragm	NSS
0	NOT SOLD SEPARATE, Retainer	NSS
0	NOT SOLD SEPARATE, Spring	NSS
0	NOT SOLD SEPARATE, Cap	NSS
0	NOT SOLD SEPARATE, Spring-Boost	NSS
0	NOT SOLD SEPARATE, Cap-Spring End	NSS
0	NOT SOLD SEPARATE, Gasket-Boost	NSS
0	NOT SOLD SEPARATE, Gasket-Pulse	NSS
0	GASKET, Fuel Pump	27-8M0204705
0	GASKET, Cylinder Block	27-430075
0	SEAL, Oil, Lower End Cap	26-419533
0	O-RING, Lower End Cap	25-89224
0	GASKET, Reed Adaptor Plate	27-879840
0	GASKET, Cover	27-879843
0	GASKET, Reed Block	27-880122
0	O-RING, (.351 x .072), Temperature Sensor	25-896699	25-888814
0	DIAPHRAGM, Poppet Comment: SN# 0T932790 & Below	812887002	812887 1 SN# 0T932790 & Below
0	DIAPHRAGM, Poppet Comment: SN# 0T932791 & Up	812887002	812887 1 SN# 0T932791 & Up
0	GASKET, Thermostat & Poppet Cover Comment: SN# 0T832040 & Below	27-879855001	27-879855 SN# 0T832040 & Below
0	GASKET, Thermostat & Poppet Cover Comment: SN# 0T832041 & Up	27-879855001	27-879855 SN# 0T832041 & Up
0	GASKET, Thermostat Comment: SN# 0T961336 & Below	27-8M0204714
0	GASKET, Thermostat Comment: SN# 0T961337 & Up	27-8M0204714
0	O-RING, (.859 x .139), Crankshaft-Lower	25-35126
0	SEAL, Oil, Crankshaft-Top	26-879635
0	SEAL, Cylinder Block	891956

Exhaust Plate

Below is the parts list for Mercury 115 EFI (4-STROKE) Exhaust Plate:

Position No.	Part Name	OEM Number	Supersedes
1	PLATE, Exhaust	881912T01
2	PIN, Dowel	17-23784
3	RETAINER	881973
4	MOUNT Comment: SN# 0T979999 & Below	881915002	881915001 SN# 0T979999 & Below
4	MOUNT Comment: SN# 0T980000 & Up	881915002	881915001 SN# 0T980000 & Up
5	SCREW, (M8 x 35)	10-881975
6	BOLT, (M12 x 175)	10-898487	10-42974
7	NUT, (M12)	11-896963	11-859129, 11-90099
8	SPACER Comment: (LONG)	23-813745	23-43041 (LONG)
8	SPACER Comment: (X-LONG)	23-11289
9	COUPLING	43585
10	GASKET	27-430086
11	TUBE, Exhaust	42966T07
12	SCREW, (M8 x 35) Stainless Steel	10-40011151
13	SEAL	8M0039075	42962
14	GROMMET Comment: SN# 0T928616 & Below	25-89417004
14	GROMMET Comment: SN# 0T928617 & Up	25-89417004
15	TUBE, Water - Long (13.21 Inches) Comment: (LONG)	32-8M0042791	32-881201 1 (LONG)
15	TUBE, Water - X Long (18.21 Inches) Comment: (X-LONG)	32-8M0042792	32-881201 2 (X-LONG)
16	CLAMP	824661
17	SEAL, Upper Comment: SN# 0T979999 & Below	814080001	814080 SN# 0T979999 & Below
17	SEAL, Upper Comment: SN# 0T980000 & Up	814080001	814080 SN# 0T980000 & Up
18	SCREW, (M8 x 45)	10-889833045
19	CLAMP	881918T03	881918T02, 881918T
20	GROMMET Comment: (.44 I.D.) SN# 0T979999 & Below	25-12602002
20	GROMMET Comment: (.44 I.D.) SN# 0T980000 & Up	25-12602002
20	GROMMET Comment: (.36 I.D.) SN# 0T979999 & Below	25-19565002
20	GROMMET Comment: (.36 I.D.) SN# 0T980000 & Up	25-19565002
21	BUSHING	23-48237
22	SHIFT SHAFT	892245T01
23	SHIFT LINK	892246A01
24	BUSHING	23-892263
25	WASHER, (.255 x .620 x .030) Stainless Steel	12-69056
26	NUT, (M6) Stainless Steel	11-401386
27	SCREW, (M8 x 35) Stainless Steel	10-40011151
28	SCREW, (M8 x 70) Stainless Steel	10-40011158
29	SWITCH	87-889514T02	87-889514A02
30	SCREW, (M3 x 20)	10-88075020
1	ADAPTOR PLATE ASSEMBLY	897580A05	888830T02
2	PIN, Dowel	17-23784
3	FITTING	22-880090
4	CHECK VALVE ASSEMBLY, Drain	21-817519A2
5	GROMMET Comment: SN# 0T943819 & Below	25-19565002
5	GROMMET Comment: SN# 0T943820 & Up	25-19565002
6	GASKET	27-8585831
7	SUMP, Oil	858572T01	858572T
8	TUBE ASSEMBLY, Exhaust	858584A1
9	O-RING	25-881295
10	GROMMET Comment: SN# 0T928616 & Below	25-89417004
10	GROMMET Comment: SN# 0T928617 & Up	25-89417004
11	TUBE, Water Comment: (LONG)	32-8M0026130	32-858575006, 32-858575 4 (LONG)
11	TUBE, Water Comment: (X-LONG)	32-8M0026129	32-858575005, 32-858575 3 (X-LONG)
12	SEAL (UPPER) Comment: SN# 0T979999 & Below	814080001	814080 SN# 0T979999 & Below
12	SEAL (Upper) Comment: SN# 0T980000 & Up	814080001	814080 SN# 0T980000 & Up
13	TUBE, Oil Pick Up	858571T
14	O-RING	25-859082
15	SCREW, (M6 x 20) Stainless Steel	10-8M0204741
16	SCREW, (M6 x 30)	10-8M0214957
17	SEAL	8M0039073	858573
18	PLUG, Drain	8288181
19	GASKET	27-8M0204692
20	SCREW, (M6 x 60)	10-82483213
21	DIPSTICK	8596021
22	SCREW, (M8 x 50)	10-4010750
23	PLUG	22-479452
24	PLUG, (.500-14)	22-889567
25	BUSHING	23-27132
26	SHIFT SHAFT	888835A1
27	SHIFT LINK	888840
28	ROLLER	888917
29	BUSHING	23-891658
30	SHIFT DETENT ASSEMBLY	888823001
31	PIN, Hair	18-82053M
32	WASHER	12-888832
33	WASHER, (.255 x .620 x .030) Stainless Steel	12-69056
34	COTTER PIN	18-26953

Flywheel

Below is the parts list for Mercury 115 EFI (4-STROKE) Flywheel:

Position No.	Part Name	OEM Number	Supersedes
1	FLYWHEEL COVER	881343T1
2	BOLT, (M6 x 20)	10-804348
3	COLLAR	825665
4	GROMMET	25-11416T
5	NUT/WASHER KIT, Hex (36 mm)	11-804265A1
6	WASHER, Plate	12-8042641
7	FLYWHEEL	280-881335T
-	STATOR KIT	398-881336T1
8	COIL, Pulser	881337T
9	STATOR	398-881336T2
10	SCREW, (M6 x 28)	10-881338
11	SCREW, (M4 x 8)	10-881339002	10-881339
12	CLAMP	54-881340
13	BOLT, (M6 x 30)	10-804603
14	PIN, Dowel	17-825010
15	ROTOR	881341
16	KEY	28-881342
17	TIMING PLATE	804266001	804266
18	SCREW	10-804267
19	NOT SOLD SEPARATE, Decal-Warning Neutral	NSS
20	NOT SOLD SEPARATE, Decal-Warning Spinning Flywheel	NSS
21	NOT SOLD SEPARATE, Decal-Servicing Referral	NSS
22	NOT SOLD SEPARATE, Decal-Engine Oil/Valve	NSS
23	NOT SOLD SEPARATE, Decal-Emergency Starting	NSS
24	DECAL, EPA Label Information Comment: 2004	37-881839A04
24	DECAL, EPA Label Information Comment: 2005	37-881839A05
-	POWERHEAD ASSEMBLY	881421T04	881421T02, 881421T01

Flywheel and Alternator

Below is the parts list for Mercury 115 EFI (4-STROKE) Flywheel and Alternator:

Position No.	Part Name	OEM Number	Supersedes
1	FLYWHEEL	200-878588T08	200-878588T03, 200-878588T04
2	DAMPER	888842T01	888842T
3	SCREW, (M8 x 20)	10-8M0143223
4	BELT	57-8M0026410	57-8M0012623, 57-892318
5	ALTERNATOR	8M6013461
6	SCREW, (M10 x 50)	10-82130150
7	WASHER	12-4002319
8	CABLE ASSEMBLY	84-856583A5
9	NUT, (M6) Stainless Steel	11-401386
10	BRACKET, Alternator	879856T02
11	PIN, Special	8215832
12	MOUNT	23-856975	849639
13	SCREW, (M10 x 45)	10-82130145
14	WASHER	12-855725
15	PLUG, Yellow	19-45907
16	WASHER, (.641 x 1.250 x .190)	12-33001
17	NUT, (M16)	11-42979

Fuel Injection Nozzle

Below is the parts list for Mercury 115 EFI (4-STROKE) Fuel Injection Nozzle:

Position No.	Part Name	OEM Number	Supersedes
1	REGULATOR, Fuel Pressure	880888T02	880888T
2	SCREW, (M6 x 12)	10-881524
3	LOCKWASHER	13-881525
4	CLIP	54-881531
5	HOSE	32-881528
6	SCREW, (M5 x 15)	10-881509
7	CLIP	54-881530
8	SCREW, (M6 x 10)	10-84088M
9	GASKET	27-827610
10	COLLAR	23-888260
11	COOLER	881527T01	881527T
12	BOLT, (M6 x 25)	10-881507
13	WASHER	12-881533
14	TIE STRAP, (5.50 Inches)	8M0214940
15	HOSE	32-881536
16	HOSE	32-881529
17	TIE STRAP, (4.00 Inches)	56762
18	DELIVERY PIPE	881518T
19	INJECTOR	880887T1
20	O-RING KIT	25-885183A1
21	CAP	881520
22	BOLT, (M6 x 10)	10-881534
23	BOLT, (M8 x 45)	10-881532
24	WASHER	12-881508
25	COLLAR	23-881526
26	NIPPLE	881521T
27	O-RING	25-881522
-	GASKET SET, Powerhead	27-858732T02	27-858732T01
-	INTAKE ASSEMBLY	881440T04	881440T 2

Fuel Injection Pump

Below is the parts list for Mercury 115 EFI (4-STROKE) Fuel Injection Pump:

Position No.	Part Name	OEM Number	Supersedes
-	VAPOR SEPERATOR	881315T05	881315T 2
1	COVER	881316T2
2	O-RING	25-881318
3	NEEDLE VALVE KIT	881329
4	NOT SOLD SEPARATE	NSS
5	FLOAT	881320
6	PIN, Float	17-881321
7	BODY	881319T
8	PLATE	881327
9	SCREW, (M3 x 8) (M3 x 8 MM)	10-8813261
10	SCREW, (M4 x 16) (M4 x 16 MM)	10-881326
11	GASKET	27-881325
12	DAMPER Comment: SN# 0T979999 & Below	25-881322
12	DAMPER Comment: SN# 0T980000 & Up	25-8M0070200	25-881322002 SN# 0T980000 & Up
13	PUMP, Fuel	8M0123823
14	FILTER	35-881323T
15	COVER	881324
16	SCREW, Drain	10-8813262
17	GASKET	27-881328
18	HOSE KIT	32-881330A02	32-881330A 1
19	CLIP	54-881331
20	CLIP	54-881559
21	FILTER KIT, Fuel Comment: (DESIGN II)	35-892758002	35-892758 (DESIGN II)
22	HOSE	32-881560
23	TEE	22-8815581
24	HOSE	32-881554	32-881551, 32-881552, 32-881553
25	HOSE	32-881554	32-881551, 32-881552, 32-881553
26	HOSE	32-881554	32-881551, 32-881552, 32-881553
27	HOSE	32-881554	32-881551, 32-881552, 32-881553
28	HOSE	32-881555
29	HOSE	32-881557
30	HOSE	32-881556
31	DAMPER	25-8813221
32	COLLAR	23-881332
33	CLAMP Comment: (DESIGN II)	54-881537
34	HOSE Comment: (DESIGN I)	32-881565
-	INTAKE ASSEMBLY	881440T04	881440T 2

Fuel Pump

Below is the parts list for Mercury 115 EFI (4-STROKE) Fuel Pump:

Position No.	Part Name	OEM Number	Supersedes
1	PUMP ASSEMBLY, Fuel	14360T74
2	DIAPHRAGM KIT	21-857005A1
3	NOT SOLD SEPARATE, Gasket-Boost	NSS
4	NOT SOLD SEPARATE, Diaphragm	NSS
5	NOT SOLD SEPARATE, Gasket-Pulse	NSS
6	NOT SOLD SEPARATE, Spring	NSS
7	NOT SOLD SEPARATE, Cap	NSS
8	NOT SOLD SEPARATE, Retainer	NSS
9	NOT SOLD SEPARATE, Spring	NSS
10	NOT SOLD SEPARATE, Cap	NSS
11	BASE	144303
12	PLATE	987752
13	FITTING, Elbow 45 Degree (1.25)	22-782792
14	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
15	SCREW, (M5 x 40)	10-82104540
16	SCREW, (M6 x 50)	10-82130050
17	ELBOW	22-888493
18	O-RING, (.301 x .070)	25-8M0204683
19	GASKET	27-8M0204705
-	GASKET SET, Powerhead	27-879855A04
1	PUMP, Fuel	880890T1
2	NOT SOLD SEPARATE, Body	NSS
3	SPRING	24-881544
4	PLUNGER	881545
5	SPRING	24-881546
6	DIAPHRAGM	881547
7	PIN	17-881548
8	NOT SOLD SEPARATE, Body	NSS
9	NOT SOLD SEPARATE, Diaphragm	NSS
10	NOT SOLD SEPARATE, Body	NSS
11	SCREW	10-881550
12	NUT	11-881333
13	O-RING	25-8M0050719	25-804255
14	CLAMP	56762
15	BOLT, (M6 x 30)	10-804256
16	HOSE	32-881543002	32-881543
17	BRACKET	881542
18	BOLT, (M6 x 16)	10-811188T	10-811188M, 10-852776 8
19	NUT Comment: SN# 0T979999 & Below	11-82382M
19	NUT Comment: SN# 0T980000 & Up	11-82382M
20	FILTER ASSEMBLY	35-881538T02	35-881538T 1
21	ELEMENT	35-8M0168897
22	O-RING	25-826966T	25-826966M
23	FLOAT	881541
24	CUP	881539
25	CLAMP	56762
26	BRACKET	804260
27	BOLT, (M7 x 48)	10-804112
28	PIN, Dowel	17-804113
29	WASHER	12-84292M
30	LEVER, Fuel Change	804257
31	SHAFT	881334
32	PIN	17-82738M
33	TUBING, (.312) (70.00 Inches Bulk) (Cut to 55 IN.)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
34	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
35	CONNECTOR	22-822769
36	NOT SOLD SEPARATE, Cap	NSS
37	CONDUIT, (.620 Inside Diameter x 3.00 Feet Bulk)	32-828547633
-	GASKET SET, Powerhead	27-858732T02	27-858732T01
-	CYLINDER HEAD ASSEMBLY	881310T09	881310T05, 881310T 1

Fuel Rail

Below is the parts list for Mercury 115 EFI (4-STROKE) Fuel Rail:

Position No.	Part Name	OEM Number	Supersedes
1	FUEL RAIL ASSEMBLY	880037T03
2	PLUG	19-804834
3	O-RING KIT	804532	25-803987
4	CLAMP	54-804830
5	SCREW PACKAGE, (M5 x 8) (2 Per) Comment: (M5 x 8)	10-804525001	804525 (M5 x 8)
5	SCREW PACKAGE, (2 Per)(M5 x 10) Comment: (M5 x 10)	10-804525001	804525 (M5 x 10)
6	O-RING KIT	25-804840
7	FITTING	22-291112
8	BRACKET	891820
9	INJECTOR	8M0222157
10	O-RING KIT	25-804530
11	O-RING KIT	25-804529
12	CLAMP	804522
13	VALVE ASSEMBLY, (.375 Inch Diameter), SCHRADER	8M0047053	883542, 804838A 1
14	CAP, Shrader Valve - Brass	22-805515	19-804839001, 19-804839
15	O-RING KIT	25-804840
16	CLAMP	8M0041097
17	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
18	PLUG	19-804835
19	O-RING KIT (16 per kit)	804532	25-803987
20	O-RING	25-804536
21	CLAMP	54-804832
22	O-RING KIT	25-804840
23	FITTING Comment: (Flange thickness is 8.65MM)	22-804836002
24	FITTING Comment: (Flange thickness is 2.65MM)	22-804836001

Fuel System

Below is the parts list for Mercury 115 EFI (4-STROKE) Fuel System:

Position No.	Part Name	OEM Number	Supersedes
1	HOSE, Vent, To Vent Fitting	32-889712001
2	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
3	HOSE ASSEMBLY, Fuel Supply	32-881040A1
4	HOSE ASSEMBLY, Fuel By-Pass	32-878506A1
5	SHRADER VALVE	884820
6	O-RING	25-891778
7	CLIP	54-884819
8	SCREW, (M6 x 12)	10-82130012
9	TUBING, (.312) (70.00 Inches Bulk) (Cut to 6-1/2 Inches) To Crankcase	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
10	CONNECTOR	22-822769
11	TUBING, (.312) (70.00 Inches Bulk) (Cut to 28 Inches)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
12	TUBING, (.312) (70.00 Inches Bulk) (Cut to 8-1/2 Inches	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
13	CLAMP, Hose (15.3)	54-8M0214964
14	HOSE	32-883545002
15	SEAL, Fuel Director	26-888852

Gear Housing(Driveshaft)(2.07:1 Gear Ratio)

Below is the parts list for Mercury 115 EFI (4-STROKE) Gear Housing(Driveshaft)(2.07:1 Gear Ratio):

Position No.	Part Name	OEM Number	Supersedes
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (LONG)	1667-9011J33
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG)	1667-9011J35
1	GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC)	1667-9011G59
2	PIN, Dowel - With Hole (.375 x .625) (FRONT)	17-8M0084244	17-43043
3	TUBE, Oiler	43046
4	SCREW KIT, (.375-16 x .250) Drain	10-79953Q04
5	SEAL	12-191833
6	PIN, Dowel - Without Hole (.375 x .625) (REAR)	17-43044
7	TRIM TAB	31640T07
8	SCREW, (.437-14 x 1.250) Stainless Steel	10-825427	10-15942
9	WASHER, (.453 x .812 x .105) Black Oxide	12-451761
10	CARRIER ASSEMBLY	43040T1
11	NOT SOLD SEPARATE, Needle Bearing	NSS
12	ANODE	97-826134Q	826134, 826134A 1
13	NUT, (M6) Stainless Steel	11-401386
14	SCREW, (M6 x 40)	10-4000333
15	GEAR, Pinion - 14 Teeth Comment: (Also Part of 43-881260A3)	43-881259T
16	NUT, (.625-18)	11-35921
17	CAM, Shift Control	850307
18	BEARING ASSEMBLY, Tapered Roller	31-883047A1
19	SHIM SET	15-44492A1
20	DRIVESHAFT ASSEMBLY Comment: (LONG)	45-888933A1
20	DRIVESHAFT ASSEMBLY Comment: (X-LONG)	45-888934A1
21	SLEEVE/RING KIT	42461A1
22	NOT SOLD SEPARATE, Seal Ring	NSS
23	COVER ASSEMBLY, Water Pump	43055A4
24	GASKET	27-430331
25	GASKET	27-8M0214931
26	SEAL, Oil (LOWER)	26-43036
27	SEAL, Oil (UPPER)	26-43035
28	GASKET	27-8172771
29	HOUSING KIT, Upper Water Pump	817275A2
30	FACEPLATE	8M0204709
31	SCREW, (M6 x 30)	10-82684430
32	SEAL	430232
33	KEY	28-8M0204723
34	IMPELLER	47-43026T2
35	SCREW, (M6 x 25)	10-82684425
36	SHIFT SHAFT ASSEMBLY Comment: (LONG -12 IN.)	853906A1
36	SHIFT SHAFT ASSEMBLY Comment: (X-LONG - 17 IN.)	853908A1
37	E RING	53-29641
38	BUSHING ASSEMBLY	23-43052A4
39	O-RING, (1.424 x .103)	25-8M0204681
40	SEAL, Oil	26-8M0204708
41	SCREW, (M6 x 25)	10-82684425
42	FACE SEAL	26-861415	26-816575
-	SEAL KIT, Gear Housing	26-43035A4
-	REPAIR KIT, Water Pump	46-8M0113799
-	REPAIR KIT, Water Pump Impeller	47-8M0100526	47-43026Q06
-	REPAIR KIT, Clutch/Cam	52-803489T1
-	BEARING/SEAL KIT (W/O Forward Bearing)	31-803496T2

Gear Housing(Driveshaft)(2.07:1Gear Ratio)

Below is the parts list for Mercury 115 EFI (4-STROKE) Gear Housing(Driveshaft)(2.07:1Gear Ratio):

Position No.	Part Name	OEM Number	Supersedes
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (LONG)	1600-888845T01
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG)	1600-888845T02
1	GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC)	1600-888845T
2	PIN, Dowel - With Hole (.375 x .625) (FRONT)	17-8M0084244	17-43043
3	TUBE, Oiler	43046
4	SCREW KIT, (.375-16 x .250) Drain	10-79953Q04
5	SEAL	12-191833
6	PIN, Dowel - Without Hole (.375 x .625) (REAR)	17-43044
7	TRIM TAB	31640T07
8	SCREW, (.437-14 x 1.250) Stainless Steel	10-825427	10-15942
9	WASHER, (.453 x .812 x .105) Black Oxide	12-451761
10	CARRIER ASSEMBLY	43040T1
11	NOT SOLD SEPARATE, Needle Bearing	NSS
12	ANODE	97-826134Q	826134, 826134A 1
13	NUT, (M6) Stainless Steel	11-401386
14	SCREW, (M6 x 40)	10-4000333
15	NOT SOLD SEPARATE, Pinion Gear (14 TEETH) Comment: (Part of 43-881260A3)	NSS
16	NUT, (.625-18)	11-35921
17	BEARING ASSEMBLY, Tapered Roller	31-883047A1
18	SHIM SET	15-44492A1
19	DRIVESHAFT ASSEMBLY Comment: (LONG)	45-858765T1
19	DRIVESHAFT ASSEMBLY Comment: (X-LONG)	45-878575T1
20	SLEEVE/RING KIT	42461A1
21	NOT SOLD SEPARATE, Seal Ring	NSS
22	COVER ASSEMBLY, Water Pump	43055A4
23	GASKET	27-430331
24	GASKET	27-8M0214931
25	SEAL, Oil (LOWER)	26-43036
26	SEAL, Oil (UPPER)	26-43035
27	GASKET	27-8172771
28	HOUSING KIT, Upper Water Pump	817275A2
29	FACEPLATE	8M0204709
30	SCREW, (M6 x 30)	10-82684430
31	SEAL	430232
32	KEY	28-8M0204723
33	IMPELLER	47-43026T2
34	SCREW, (M6 x 25)	10-82684425
35	FACE SEAL	26-861415	26-816575
36	SHIFT SHAFT ASSEMBLY Comment: (LONG)	884563A00
36	SHIFT SHAFT ASSEMBLY Comment: (X-LONG)	884565A00
37	E RING	53-29641
38	BUSHING ASSEMBLY	23-43052A4
39	O-RING, (1.424 x .103)	25-8M0204681
40	SEAL, Oil	26-8M0204708
41	SCREW, (M6 x 25)	10-82684425
42	BUSHING Comment: (NOT included with complete replacement Gear Housings)	23-891637
-	SEAL KIT, Gear Housing	26-43035A4
-	REPAIR KIT, Water Pump	46-8M0113799
-	BEARING/SEAL KIT Comment: (W/O FORWARD BRG.)	31-803496T2
-	REPAIR KIT, Clutch And Cam Follower	52-888805A00
-	REPAIR KIT, Water Pump Impeller	47-8M0100526	47-43026Q06

Gear Housing(Driveshaft)(2.33:1 Gear Ratio)

Below is the parts list for Mercury 115 EFI (4-STROKE) Gear Housing(Driveshaft)(2.33:1 Gear Ratio):

Position No.	Part Name	OEM Number	Supersedes
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (LONG)	1667-9011J37
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG)	1667-9011J39
1	GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC)	1667-9011G59
2	PIN, Dowel - With Hole (.375 x .625) (FRONT)	17-8M0084244	17-43043
3	TUBE, Oiler	43046
4	SCREW KIT, (.375-16 x .250) Drain	10-79953Q04
5	SEAL	12-191833
6	PIN, Dowel - Without Hole (.375 x .625) (REAR)	17-43044
7	TRIM TAB	31640T07
8	SCREW, (.437-14 x 1.250) Stainless Steel	10-825427	10-15942
9	WASHER, (.453 x .812 x .105) Black Oxide	12-451761
10	CARRIER ASSEMBLY	43040T1
11	NOT SOLD SEPARATE, Needle Bearing	NSS
12	ANODE	97-826134Q	826134, 826134A 1
13	NUT, (M6) Stainless Steel	11-401386
14	SCREW, (M6 x 40)	10-4000333
15	NOT SOLD SEPARATE, Pinion Gear (12 Teeth) Comment: (PART OF 43-882813A3)	NSS
16	NUT, (.625-18)	11-35921
17	CAM, Shift Control	850307
18	BEARING ASSEMBLY, Tapered Roller	31-883047A1
19	SHIM SET	15-44492A1
20	DRIVESHAFT ASSEMBLY Comment: (LONG)	45-888933A1
20	DRIVESHAFT ASSEMBLY Comment: (X-LONG)	45-888934A1
21	SLEEVE/RING KIT	42461A1
22	NOT SOLD SEPARATE, Seal Ring	NSS
23	COVER ASSEMBLY, Water Pump	43055A4
24	GASKET	27-430331
25	GASKET	27-8M0214931
26	SEAL, Oil (LOWER)	26-43036
27	SEAL, Oil (UPPER)	26-43035
28	GASKET	27-8172771
29	HOUSING KIT, Upper Water Pump	817275A2
30	FACEPLATE	8M0204709
31	SCREW, (M6 x 30)	10-82684430
32	SEAL	430232
33	KEY	28-8M0204723
34	IMPELLER	47-43026T2
35	SCREW, (M6 x 25)	10-82684425
36	SHIFT SHAFT ASSEMBLY Comment: (LONG)	853906A1
36	SHIFT SHAFT ASSEMBLY Comment: (X-LONG)	853908A1
37	E RING	53-29641
38	BUSHING ASSEMBLY	23-43052A4
39	O-RING, (1.424 x .103)	25-8M0204681
40	SEAL, Oil	26-8M0204708
41	SCREW, (M6 x 25)	10-82684425
42	FACE SEAL	26-861415	26-816575
-	SEAL KIT, Gear Housing	26-43035A4
-	REPAIR KIT, Water Pump	46-8M0113799
-	REPAIR KIT, Water Pump Impeller	47-8M0100526	47-43026Q06
-	REPAIR KIT, Clutch/Cam	52-803489T1
-	BEARING/SEAL KIT (W/O Forward Bearing)	31-803496T2

Gear Housing, Propeller Shaft - 2.07:1 Gear Ratio

Below is the parts list for Mercury 115 EFI (4-STROKE) Gear Housing, Propeller Shaft - 2.07:1 Gear Ratio:

Position No.	Part Name	OEM Number	Supersedes
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (LONG)	1667-9011J33
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG)	1667-9011J35
1	GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC)	1667-9011G59
2	BEARING SET, Cup And Cone	31-30894A1
3	NOT SOLD SEPARATE, Cup	NSS
4	GEAR, Forward - 29 Teeth	43-881260A3
5	BEARING, Needle	31-30895T
6	RING, Retaining	53-856823
7	FOLLOWER KIT, Cam	850315A1
8	BALL	30-44530
9	NOT SOLD SEPARATE, Slide	NSS
10	SPRING	24-850327
11	CLUTCH	52-850048T	52-850048
12	PIN, Cross	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
13	SPRING	24-30893
14	PROPELLER SHAFT	44-8M0140445
15	GEAR, Reverse - 29 Teeth	43-850036T	43-850036
16	CARRIER ASSEMBLY, Bearing	8M0168901
17	O-RING, (3.609 x .139)	25-8M0214974
18	BEARING, Needle	31-30956T
19	SEAL, Oil (INNER)	26-8M0205728
20	SEAL, Oil (OUTER)	26-8M0205729
21	BEARING, Roller	31-12578T
22	THRUST WASHER	12-12577
23	BEARING, Thrust	31-12576
24	STUD, (M8 x 48)	16-8M0034456	16-42917 2
25	WASHER	12-855941
26	NUT, (M8)	11-401378
27	SHIM SET	15-44491A1
28	NOT SOLD SEPARATE, Insert	NSS
29	NOT SOLD SEPARATE, Decal-G/H Pinion Ident.	NSS
30	FLO TORQUE III KIT	8M0150151
31	NOT SOLD SEPARATE, Adaptor	NSS
32	NOT SOLD SEPARATE, Lock Nut	NSS
-	SEAL KIT, Gear Housing	26-43035A4
-	REPAIR KIT, Clutch/Cam	52-803489T1
-	BEARING/SEAL KIT (W/O Forward Bearing)	31-803496T2
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (LONG)	1600-888845T01
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG)	1600-888845T02
1	GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC)	1600-888845T
2	INSERT, Threaded	8227731
3	FOLLOWER ASSEMBLY, Cam	888807
4	SHIFT CAM Comment: SN# 0T845781 & Below	8M4504018
4	SHIFT CAM Comment: SN# 0T845782 & Up	8M4504018
5	ROD, Clutch Actuator	888806
6	PIN, Cross	17-8M0084243	17-78905
7	PIN, Spring Locator	17-8M0084245	17-78906
8	SPRING	24-79910
9	WASHER	12-78910
10	SHIM SET	15-44491A1
11	BEARING SET, Cup And Cone	31-30894A1
12	NOT SOLD SEPARATE, Cup	NSS
13	GEAR, Forward - 29 Teeth (29 TEETH)	43-881260A3
14	BEARING, Needle	31-30895T
15	RING, Retaining	53-856823
16	CLUTCH	52-888805T
17	PROPELLER SHAFT	44-8M0140444
18	SPRING	24-30893
19	GEAR, Reverse (29 Teeth) (29 TEETH)	43-889991T
20	CARRIER ASSEMBLY, Bearing	8M0168901
21	O-RING, (3.609 x .139)	25-8M0214974
22	BEARING, Needle	31-30956T
23	SEAL, Oil (INNER)	26-8M0205728
24	SEAL, Oil (OUTER)	26-8M0205729
25	BEARING, Roller	31-12578T
26	THRUST WASHER	12-12577
27	BEARING, Thrust	31-12576
28	STUD, (M8 x 48)	16-8M0034456	16-42917 2
29	WASHER, (.323 x .590 x .112) Stainless Steel	12-855941
30	NUT, (M8)	11-401378
31	NOT SOLD SEPARATE, Decal-G/H Pinion Ident.	NSS
-	SEAL KIT, Gear Housing	26-43035A4
-	BEARING/SEAL KIT Comment: (W/O FORWARD BRG.)	31-803496T2
-	REPAIR KIT, Clutch And Cam Follower	52-888805A00

Gear Housing, Propeller Shaft - 2.33:1 Gear Ratio

Below is the parts list for Mercury 115 EFI (4-STROKE) Gear Housing, Propeller Shaft - 2.33:1 Gear Ratio:

Position No.	Part Name	OEM Number	Supersedes
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (LONG)	1667-9011J37
0	GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG)	1667-9011J39
1	GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC)	1667-9011G59
2	BEARING SET, Cup And Cone	31-30894A1
3	NOT SOLD SEPARATE, Cup	NSS
4	GEAR KIT, Forward And Pinion 28 Teeth (28 TEETH)	43-882813A3
5	BEARING, Needle	31-30895T
6	RING, Retaining	53-856823
7	FOLLOWER KIT, Cam	850315A1
8	BALL	30-44530
9	NOT SOLD SEPARATE, Slide	NSS
10	SPRING	24-850327
11	CLUTCH	52-850048T	52-850048
12	PIN, Cross	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
13	SPRING	24-30893
14	PROPELLER SHAFT	44-8M0140445
15	GEAR, Reverse - 28 Teeth (28 TEETH)	43-882814T
16	CARRIER ASSEMBLY, Bearing	8M0168901
17	O-RING, (3.609 x .139)	25-8M0214974
18	BEARING, Needle	31-30956T
19	SEAL, Oil (INNER)	26-8M0205728
20	SEAL, Oil (OUTER)	26-8M0205729
21	BEARING, Roller	31-12578T
22	THRUST WASHER	12-12577
23	BEARING, Thrust	31-12576
24	STUD, (M8 x 48) (M8 X 48 MM)	16-8M0034456	16-42917 2
25	WASHER	12-855941
26	NUT, (M8)	11-401378
27	SHIM SET	15-44491A1
28	NOT SOLD SEPARATE, Insert	NSS
29	NOT SOLD SEPARATE, Decal-G/H Pinion Ident.	NSS
30	FLO TORQUE III KIT	8M0150151
31	NOT SOLD SEPARATE, Adaptor	NSS
32	NOT SOLD SEPARATE, Lock Nut	NSS
-	SEAL KIT, Gear Housing	26-43035A4
-	REPAIR KIT, Clutch/Cam	52-803489T1
-	BEARING/SEAL KIT (W/O Forward Bearing)	31-803496T2

Ignition Components

Below is the parts list for Mercury 115 EFI (4-STROKE) Ignition Components:

Position No.	Part Name	OEM Number	Supersedes
1	ECU, Engine Control Unit	880891T14	880891T12, 880891T11, 880891T 1
2	BOLT, (M6 x 28)	10-804270
3	GROMMET	25-881304	25-93114M
4	BUSHING	23-804344003	23-82851M
5	RECTIFIER/REGULATOR ASSEMBLY	881346T
6	BOLT, (M6 x 25)	10-853536
7	BOLT, (M6 x 20)	10-804604
8	COIL, Ignition	300-8M0123821
9	COIL, Ignition	339-8M0121257
10	PLATE	881345
11	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
12	BOLT, (M6 x 25)	10-853536
13	CLAMP	54-804276
14	CLAMP	54-804277

Intake

Below is the parts list for Mercury 115 EFI (4-STROKE) Intake:

Position No.	Part Name	OEM Number	Supersedes
1	MANIFOLD	880886T
2	O-RING	25-881513
3	PIN, Dowel	17-881512
4	BOLT, (M6 x 25)	10-881507
5	THROTTLE BODY ASSEMBLY	881441T4
6	SPRING	24-881444
7	BOLT, (M8 x 70)	10-881510
8	WASHER	12-881508
9	THROTTLE BODY ASSEMBLY	881441T3
10	SCREW	10-881442
11	SPRING	24-881444
12	SCREW	10-881443
13	LINK JOINT	881514
14	LINK JOINT	881515
15	NUT	11-83763M
16	SENSOR, Throttle	880884T
17	O-RING	25-881504
18	SCREW	10-881502002	10-881502
19	WASHER	12-881450
20	BRACKET	881516
21	SCREW	10-881971A1
22	HOSE	881511
-	CONTROL VALVE ASSEMBLY	880883T1
23	BODY	881446T
24	CONTROL VALVE	881447T
25	O-RING	25-881448
26	SCREW, (M4 x 12)	10-881449002	10-881449
27	WASHER	12-881450
28	FILTER	35-881501T
29	SENSOR, Pressure	880885T
30	SCREW, (M5 x 15)	10-881509
31	BOLT, (M6 x 24)	10-881505
32	BOLT, (M6 x 60)	10-881506
33	HARNESS ASSEMBLY	84-881517T1
-	INTAKE ASSEMBLY	881440T04	881440T 2

Intake Silencer

Below is the parts list for Mercury 115 EFI (4-STROKE) Intake Silencer:

Position No.	Part Name	OEM Number	Supersedes
1	SILENCER, Intake	881436T
2	THERMOSENSOR	880882T
3	O-RING	25-881437
4	BOLT, (M6 x 16)	10-804165
5	BOLT, (M8 x 20)	10-881816
6	BRACKET	881439
7	BRACKET	8M0059034	881434
8	BOLT, (M6 x 20)	10-881435
9	INDUCTION SILENCER Comment: SN# 0T979999 & Below	892849	881010T SN# 0T979999 & Below
9	INDUCTION SILENCER Comment: SN# 0T980000 & Up	892849	881010T SN# 0T980000 & Up
10	BRACKET	881269
11	SCREW, (M6 x 20) Stainless Steel	10-8M0204741
12	PIN	17-804160
13	GASKET	27-881433
14	BREATHER PIPE	32-804162
15	CLAMP	54-804163
16	BOLT, (M6 x 12)	10-804602
17	CLIP	54-804089
18	CLAMP Comment: SN# 0T979999 & Below	56762
18	TIE STRAP, (4.00 Inches) Comment: SN# 0T980000 & Up	56762
19	BOLT, (M6 x 105)	10-881438
20	BOLT, (M8 x 40)	10-881431
21	SCREEN	881822
-	GASKET SET, Powerhead	27-858732T02	27-858732T01
-	POWERHEAD ASSEMBLY	881421T04	881421T02, 881421T01

Intake and Exhaust Valves

Below is the parts list for Mercury 115 EFI (4-STROKE) Intake and Exhaust Valves:

Position No.	Part Name	OEM Number	Supersedes
1	V BELT	57-804145
2	BOLT, (M10 x 35)	10-804143001	10-804143
3	GEAR, Driven	43-804142T
4	SEAL, Oil	26-804144001	26-804144
5	PIN, Dowel	17-804141
6	CAMSHAFT	2407-8M0057172	2407-804140T
7	CAMSHAFT	2407-804139T
8	VALVE, Intake	804128T
9	VALVE, Exhaust	804129T
10	SEAT	804130
11	SEAL	26-804136
12	SEAL	26-804137
13	SPRING, Valve	24-804131
14	RETAINER	804132
15	COTTER VALVE	28-804135
16	LIFTER, Valve	804138T
17	SHIM Comment: (2.350)	15-8046071
17	SHIM Comment: (2.375)	15-8046072
17	SHIM Comment: (2.400)	15-8046073
17	SHIM Comment: (2.425)	15-8046074
17	SHIM Comment: (2.450)	15-8046075
17	SHIM Comment: (2.475)	15-8046076
17	SHIM Comment: (2.500)	15-8046077
17	SHIM Comment: (2.525)	15-8046078
17	SHIM Comment: (2.550)	15-8046079
17	SHIM Comment: (2.575)	15-80460710
17	SHIM Comment: (2.600)	15-80460711
17	SHIM Comment: (2.625)	15-80460712
17	SHIM Comment: (2.650)	15-80460713
17	SHIM Comment: (2.675)	15-80460714
17	SHIM Comment: (2.700)	15-80460715
17	SHIM Comment: (2.725)	15-80460716
17	SHIM Comment: (2.750)	15-80460717
17	SHIM Comment: (2.775)	15-804608
17	SHIM Comment: (2.800)	15-80460810
17	SHIM Comment: (2.825)	15-80460820
17	SHIM Comment: (2.850)	15-80460830
17	PAD, Adjusting Comment: (2.875)	15-80460840
17	SHIM Comment: (2.900)	15-80460850
17	SHIM Comment: (2.925)	15-80460860
17	SHIM Comment: (2.950)	15-80460870
17	SHIM Comment: (2.975)	15-80460880
18	PLATE, Valve	804149
19	KEY	28-804153
20	TENSIONER	804146
21	BOLT, (M10 x 45)	10-804150
22	SPRING	24-804147
23	HOSE	32-804148
24	GEAR, Drive	43-804151T
25	NUT, (M40) (40MM)	11-881314003	11-881314
-	GASKET SET, Powerhead	27-858732T02	27-858732T01
-	CYLINDER HEAD ASSEMBLY	881310T09	881310T05, 881310T 1
-	POWERHEAD ASSEMBLY	881421T04	881421T02, 881421T01

Oil Pump

Below is the parts list for Mercury 115 EFI (4-STROKE) Oil Pump:

Position No.	Part Name	OEM Number	Supersedes
1	O-RING	25-62705001
2	PIN, Dowel	17-41275M
3	MOUNT	881900T03	881900T02, 881900T01, 881900T, 44344T 2
4	BOLT, (M12 x 175)	10-898487	10-42974
5	WASHER, Neoprene	12-32834
6	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
7	NUT, (M12)	11-896963	11-859129, 11-90099
8	SCREW, (M8 x 50)	10-4010750
9	PUMP, Oil	858579T3
10	BOLT, (M6 x 45)	10-8M0052670	10-858719
11	SEAL	26-804349
12	BRACKET ASSEMBLY, Shift Linkage	888834T01
13	DRIVE SCREW	10-42975
14	SCREW, (M6 x 20)	10-82130020
15	CUP, Barrel Retainer (LARGE)	889530
16	LATCH	98889
17	CUP, Barrel Retainer, Barrel Retainer (SMALL)	824015
18	LATCH	889529
19	SWITCH	87-879996A2
20	SCREW, (M3 x 20)	10-88075020
21	SEAL	8M0043168	884256 3
22	PIN, Dowel	17-23784

Oil Tank

Below is the parts list for Mercury 115 EFI (4-STROKE) Oil Tank:

Position No.	Part Name	OEM Number	Supersedes
1	TANK, Oil	1200-879844T08	879844T04
2	VENT ASSEMBLY	19299A1
3	VALVE	21-64871
4	SWITCH	87-856156T04	87-856156A 4
5	WASHER, (.203 x .562 x .060) Stainless Steel	12-72761
6	SCREW, (.164-18 x .375)	10-58376
7	BUSHING	23-883821
8	GROMMET Comment: SN# 0T979999 & Below	25-883820001	25-883820 SN# 0T979999 & Below
8	GROMMET Comment: SN# 0T980000 & Up	25-883820001	25-883820 SN# 0T980000 & Up
9	FILTER	35-883037T
10	COVER, To Air Compressor	883044001
11	SCREW, (#10-16 x 1.25)	10-883075
12	PLUG	19-854310	806899
13	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
14	BOOT	25-879857
15	CAP	36-8M0073266	8M0043969, 8M0030358, 828475A09, 828475A 8
16	O-RING	25-26318T
17	CHAIN	887776002	887776001
18	NUT	11-65110
19	SCREW, (M8 x 35)	10-82446035
20	WASHER	12-4002318
21	DECAL, Caution-Start in Gear Comment: (Start In Gear)	37-881865	37-825064 (Start In Gear)

Oiling System

Below is the parts list for Mercury 115 EFI (4-STROKE) Oiling System:

Position No.	Part Name	OEM Number	Supersedes
1	HOSE, (.125 x 25.00 Inches)	32-88306955
2	TUBING, (18.00 Inches Bulk) (Cut to 13 Inches	32-88104441
3	TUBING, (18.00 Inches Bulk) (Cut to 13-1/2 Inches)	32-88104441
4	TUBING, (18.00 Inches Bulk) (Cut to 18 Inches)	32-88104441
5	TUBING, (25.00 Inches Bulk) (Cut to 3-1/4 Inches	32-82381455
6	TUBING, (25.00 Inches Bulk) (Cut to 7 Inches	32-82381455
7	FILTER, Oil - In Line	35-875284T01	35-875284001, 35-875284
8	TIE STRAP, (4.00 Inches)	56762
9	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
10	CONDUIT, (10.00 Inches Bulk) (Cut to 6 Inches	32-828547412
11	TIE STRAP, (5.50 Inches)	8M0214940
12	PUMP ASSEMBLY, Oil	8M0185614
13	SCREW, (M8 x 20)	10-81893420
14	TUBING, (18.00 Inches Bulk) (Cut to 8 Inches	32-88104441

Poppet/Thermostat Mounting

Below is the parts list for Mercury 115 EFI (4-STROKE) Poppet/Thermostat Mounting:

Position No.	Part Name	OEM Number	Supersedes
1	POPPET	884389
2	DIAPHRAGM Comment: SN# 0T932790 & Below	812887002	812887 1 SN# 0T932790 & Below
2	DIAPHRAGM Comment: SN# 0T932791 & Up	812887002	812887 1 SN# 0T932791 & Up
3	WASHER	12-94182
4	SCREW, (#10-16 x .750) (10-16 x 3/4)	10-69570
5	SPRING	24-892321
6	COVER	8M0036780	879854
7	SCREW, (M8 x 35)	10-82127335
8	GASKET Comment: SN# 0T832040 & Below	27-879855001	27-879855 SN# 0T832040 & Below
8	GASKET Comment: SN# 0T832041 & Up	27-879855001	27-879855 SN# 0T832041 & Up
9	GASKET Comment: SN# 0T961336 & Below	27-8M0204714
9	GASKET Comment: SN# 0T961337 & Up	27-8M0204714
10	THERMOSTAT, 62Â°C (143Â°F) Comment: SN# 0T979999 & Below	833072004	833072002 SN# 0T979999 & Below
10	THERMOSTAT, 62Â°C (143Â°F) Comment: SN# 0T980000 & Up	833072004	833072002 SN# 0T980000 & Up
11	CLAMP	54-814634
12	SCREW, (M6 x 12)	10-82130012
13	SENSOR ASSEMBLY	8M0148668
14	O-RING, (.351 x .072)	25-896699	25-888814
15	SPACER	23-892265
0	GASKET SET, Powerhead	27-879855A04
0	POWERHEAD ASSEMBLY Comment: (75)	895233A07	895233A05 (75)
0	POWERHEAD ASSEMBLY Comment: 90/115	891767A07	891767A04 90/115

Power Trim Components

Below is the parts list for Mercury 115 EFI (4-STROKE) Power Trim Components:

Position No.	Part Name	OEM Number	Supersedes
-	PUMP ASSEMBLY, Power Trim	8M0171818
1	SHOCK ROD KIT	8M0171821
2	O-RING KIT, Rebuild	25-8M0171819
3	PISTON ASSEMBLY, Memory	8M0171822
4	CYLINDER ASSEMBLY	893916A01	811669A 1
5	VALVE KIT, Trim Limit	893905A02	809873A 1
6	PUMP ASSEMBLY	893906A02	809874A 1
7	MOTOR KIT	893907A02	809885A 2
8	PLUG	22-8134351
9	MANUAL RELEASE ASSEMBLY	893929A01	813442A 2
10	MANIFOLD KIT	893909A02	809875A 1
11	SCREW KIT (MOTOR)	10-809876A1
12	CABLE ASSEMBLY	88238A18
13	DRIVESHAFT/SEAL KIT	809877A1
14	FILTER KIT	35-893912A02	809878A 1
15	POPPET KIT	893913A02	809879A 1
-	O-RING KIT (COMPLETE TRIM)	25-893914A02	25-809880A 1
16	PIN, Trilobe	17-821539	17-13794, 17-19603
17	PIN, Anchor	17-818898
18	SHAFT Comment: SN# 0T979999 & Below	99625002
18	SHAFT Comment: SN# 0T980000 & Up	99625002
-	PUMP ASSEMBLY, Power Trim	8M0171818
1	SHOCK ROD KIT	8M0171821
2	O-RING KIT, Rebuild	25-8M0171819
3	PISTON ASSEMBLY, Memory	8M0171822
4	CYLINDER ASSEMBLY	893916A01	811669A 1
5	VALVE KIT, Trim Limit	893905A02	809873A 1
6	PUMP ASSEMBLY	893906A02	809874A 1
7	MOTOR KIT	893907A02	809885A 2
8	PLUG	22-8134351
9	MANUAL RELEASE ASSEMBLY	893929A01	813442A 2
10	MANIFOLD KIT	893909A02	809875A 1
11	SCREW KIT (MOTOR)	10-809876A1
12	CABLE ASSEMBLY	88238A18
13	DRIVESHAFT/SEAL KIT	809877A1
14	FILTER KIT	35-893912A02	809878A 1
15	POPPET KIT	893913A02	809879A 1
-	O-RING KIT (COMPLETE TRIM)	25-893914A02	25-809880A 1
16	PIN, Trilobe	17-821539	17-13794, 17-19603
17	PIN, Anchor	17-818898
18	SHAFT Comment: SN# 0T928909 & Below	99625002
18	SHAFT Comment: SN# 0T928910 & Up	99625002

Powerhead Gasket Set Components

Below is the parts list for Mercury 115 EFI (4-STROKE) Powerhead Gasket Set Components:

Position No.	Part Name	OEM Number	Supersedes
-	GASKET SET, Powerhead	27-858732T02	27-858732T01
0	GASKET, Thermosensor	27-8042971
0	O-RING, Fuel Pump	25-8M0050719	25-804255
0	GASKET, Intake Manifold	27-827610
0	SEAL, Oil, Camshaft	26-804144001	26-804144
0	O-RING, Intake Silencer	25-881437
0	GASKET, Intake Manifold	27-881433
0	GASKET, Cylinder Block	27-858732002	27-858732 1
0	GASKET, Cylinder Block	27-81990M
0	GASKET, Exhaust Cover	27-804076003	27-804076, 27-804076001
0	GASKET, Screw Plug	27-881426
0	GASKET, Pressure Control Valve Cover	27-804084
0	GASKET, Cylinder Head	27-8041151
0	GASKET, Cylinder Head Cover	27-804123
0	SEAL, Oil, Crankshaft-Top	26-8040992
0	SEAL, Oil, Crankshaft-Bottom	26-8041002
0	O-RING, Intake Manifold	25-881513
0	WASHER, Sealing, Cylinder Head	12-831246
0	O-RING, Fuel Pump Comment: (Not used for this application)	25-8M0052669	25-825492 (Not used for this application)

Reed Block

Below is the parts list for Mercury 115 EFI (4-STROKE) Reed Block:

Position No.	Part Name	OEM Number	Supersedes
1	SHIFT RAIL ASSEMBLY	42881A1
2	TAB WASHER	14-42981
3	SCREW, (M8 x 25)	10-40001134
4	SLIDE	988851
5	NUT, (M6) Stainless Steel	11-401386
6	WASHER	12-35459
7	NUT, (M6) Stainless Steel	11-401386
8	GASKET	27-430075
9	CAP ASSEMBLY, Lower End	1169-858552T2
10	CHECK VALVE	21-426585
11	SEAL, Oil	26-419533
12	O-RING	25-89224
13	SCREW, (M10 x 25) Hex Flange - Stainless Steel	10-4010825
14	PLATE ASSEMBLY, Reed Adaptor	879839A00
15	GASKET	27-879840
16	FITTING	22-768431
17	COVER	879841A03
18	GASKET	27-879843
19	SCREW, (M8 x 45)	10-82127345
20	SCREW, (M8 x 35)	10-82127335
21	REED BLOCK	828623T4
22	GASKET	27-880122
23	SCREW, (M6 x 20)	10-4007420
24	SENSOR, MAP	854445
25	BRACKET, MAP Sensor	884522	804873, 841095
26	SCREW, (M6 x 16)	10-82130016
27	SENSOR ASSEMBLY	8M0148668
28	O-RING, (.351 x .072)	25-896699	25-888814
29	CABLE ASSEMBLY, Battery - Negative	84-88439A26
30	SCREW, (M8 x 14)	10-81893414
31	WASHER	12-36001
32	CLAMP	54-889559
33	WASHER, (.255 x .620 x .030) Stainless Steel	12-69056
0	GASKET SET, Powerhead	27-879855A04
0	POWERHEAD ASSEMBLY Comment: 75	895233A07	895233A05 75
0	POWERHEAD ASSEMBLY Comment: 90/115	891767A07	891767A04 90/115

Sensors

Below is the parts list for Mercury 115 EFI (4-STROKE) Sensors:

Position No.	Part Name	OEM Number	Supersedes
1	THERMOSENSOR	804295T
2	RETAINER	804296
3	BOLT, (M6 x 16)	10-811188T	10-811188M, 10-852776 8
4	GASKET	27-8042971
5	CLAMP	54-83577M
6	SCREW, (M6 x 10)	10-84088M
7	PLATE	881366
8	BOLT, (M6 x 12)	10-804602
9	PLATE	8042941
10	BOLT, (M6 x 16)	10-811188T	10-811188M, 10-852776 8
11	HARNESS ASSEMBLY	84-881364T05	84-881365T 1
12	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
13	TIE STRAP, (4.00 Inches)	56762
14	SWITCH, Oil Pressure	87-8043071
15	LEAD WIRE	84-881367A1
16	BOLT, (M6 x 20)	10-804604
-	GASKET SET, Powerhead	27-858732T02	27-858732T01
-	POWERHEAD ASSEMBLY	881421T04	881421T02, 881421T01

Service/Support Material

Below is the parts list for Mercury 115 EFI (4-STROKE) Service/Support Material:

Part Name	OEM Number	Supersedes
PARTS MANUAL, 75/90/115 DFI	90-891837004
SERVICE MANUAL	90-8M0047659	90-889785R01, 90-889785
OWNERS MANUAL Comment: 2004	90-10208040
OWNERS MANUAL Comment: 2004-1/2	90-10208051
OWNERS MANUAL Comment: 2005	90-10208051
OPERATION MANUAL	90-10229021
DECAL, California Ultra Low Emissions	37-88343312
DECAL, EPA Label Information Comment: 2004	37-891765A04
DECAL, EPA Label Information Comment: 2005	37-891765A05
PARTS MANUAL, 115 EFI (4-Stroke)	90-881838004
SERVICE MANUAL	90-881980R03	90-881980R02, 90-881980R 1
OWNERS MANUAL Comment: 2004	90-10215040
OWNERS MANUAL Comment: 2005	90-10215050
HOSE ASSEMBLY, Fuel	32-858610A31	32-858610A10, 32-16789A18
SCRENCH TOOL, (10 mm)	91-880177
STARBIT TOOL KIT	91-881828
OIL-10W30	92-8M0078625	92-858045K01, 92-802833A 1

Starter Motor

Below is the parts list for Mercury 115 EFI (4-STROKE) Starter Motor:

Position No.	Part Name	OEM Number	Supersedes
1	STARTER MOTOR ASSEMBLY Comment: SN# 0T842988 & Up	50-892339T01	50-892339T, 50-853329T SN# 0T842988 & Up
1	STARTER MOTOR ASSEMBLY Comment: SN# 0T842987 & Below	50-892339T01	50-892339T, 50-853329T SN# 0T842987 & Below
2	THRU BOLT	10-803005
3	GEAR KIT	43-880805A1
4	SOLENOID KIT	809463A1
5	SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel	10-69035
6	CABLE ASSEMBLY, (6.00 Inches) Black	84-93388A1
7	DECAL, Warning, High Voltage	37-8272822
8	LOCKWASHER, (M5)	13-400255
9	NUT, (M5) Stainless Steel	11-400211
10	LOCKWASHER, (.312)	13-8M0204647
11	NUT, (M8) Stainless Steel	11-400213
12	COLLAR	23-8M0034918	23-8M0001391, 56703
13	STOP	8M0043276	879845
-	STARTER MOTOR ASSEMBLY	50-881368T2
1	STATOR	804314T
2	ARMATURE	804313T
3	HOLDER ASSEMBLY, Brush	881369T1
4	BRUSH SET	804316
5	SPRING	24-804317
6	BRACKET	881370T	888336T
7	SCREW, (M4 x 16)	10-804337
8	THRU BOLT, (M6 x 120)	10-804335
9	GEAR KIT	804321T1
10	CLUTCH	804322
11	WASHER KIT	12-804330
12	BRACKET	804324
13	RING GEAR	804326
14	GASKET	27-804327
15	BEARING	31-804325
16	SHAFT, Pinion	804323
17	IDLER GEAR	43-804329001	43-804329
18	BRACKET	804328
19	COVER	804331T
20	BOLT, (M6 x 52)	10-804336
21	PINION	804319
22	STOP SET, Pinion	804320
23	LEVER KIT	804332
24	COVER	804334
25	RELAY, Starter	881371T1
26	BOLT, (M8 x 45)	10-804605
27	TERMINAL	881373
28	LOCKWASHER	13-881377
29	NUT	11-82382M
30	NUT	11-881372
31	COVER	881374

Steering Handle Kit

Below is the parts list for Mercury 115 EFI (4-STROKE) Steering Handle Kit:

Position No.	Part Name	OEM Number	Supersedes
-	STEERING HANDLE KIT	816366A32
1	HANDLE ASSEMBLY, Steering Arm	12020A3
NS	FITTING, Grease	22-8M0169589
2	BUSHING	23-42992T02
3	HOUSING	48414
4	PLATE	48519
5	GASKET	27-48518
6	SCREW, (#10-16 x .600)	10-878609	10-812832 1
7	SCREW, (#10-16 x .500)	10-878608	10-812832
8	CLAMP	54-889729	54-12013
9	SCREW, (M5 x 40)	10-40007112
10	WING NUT,	10-32,11-816874	11-73651, 11-816873, 11-90052
11	SWITCH KIT, Stop - Throttle Handle	87-823609A15	87-15823A 6, 96495A 3, 87-15823A 5
12	SWITCH ASSEMBLY, Stop	87-8M0104612	87-823609A 5
13	NOT SOLD SEPARATE, Insulator	NSS
14	TUBE ASSEMBLY, Throttle	12018A4
15	NOT SOLD SEPARATE, Drive Wheel	NSS
16	NOT SOLD SEPARATE, Roll Pin	NSS
17	SCREW, (#10-16 x .375)	10-62568
18	GRIP	8M0221732
19	CLIP	54-648552
20	NUT, (M10)	11-40140
21	CONDUIT, (9.03 Inches)	8885241
22	GUIDE TUBE	895665
23	BARREL, Throttle Acutator	89578
24	SET SCREW,	10-32,10-824081	10-89601
25	CABLE ASSEMBLY	12019003
26	GUIDE, Cable	8M0204660
27	ANCHOR, Cable End	20007
28	SET SCREW,	8-32,10-8M0204644
29	SCREW, (M10 x 105) Hex Flange - Stainless Steel	10-823567105	10-817430105
30	CAP	48416
31	WASHER	12-4002319
32	WASHER, (.402 x .787 x .039 Bellevi)	12-12024
33	SPACER	23-146011
34	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
35	NOT SOLD SEPARATE, Decal-Throttle	NSS
36	GROMMET, Hose Cable	25-889724	858741 1, 858741 2

Steering Handle Kit Components

Below is the parts list for Mercury 115 EFI (4-STROKE) Steering Handle Kit Components:

Position No.	Part Name	OEM Number	Supersedes
-	STEERING HANDLE KIT	816366A32
1	HANDLE, Bracket	816366T10
2	SCREW, (.313-24 x 3.50)	10-881261
3	TAB WASHER	14-42981
4	SPACER	822263
5	HARNESS ASSEMBLY	84-12649A4
6	SWITCH KIT, Key Comment: (See Chart Below for Keys)	87-88107A5
7	NUT, Special - Black Nylon Comment: (Black Nylon)	11-879755	11-93543 (Black Nylon)
8	PLUG, Male	13541
9	GROMMET	121051
10	PLUG	19-889730	19-12014
11	RETAINER, Brass	8M0032846	12044 1
12	COVER	8158041
13	SCREW, (#10-16 x .500)	10-878608	10-812832
14	SWITCH ASSEMBLY, Stop	87-11083A4
15	LANYARD ASSEMBLY	15920Q54
16	CABLE ASSEMBLY	84-11149A3
17	HORN ASSEMBLY	889528T01
18	SWITCH KIT, Trim (25.00 Feet), Trim	87-18286A19
19	SWITCH	87-8M0052927	87-813960A 3
20	SCREW, (#6-32 x .750)	10-12110
21	CLAMP	54-648551
22	SCREW, (#10-16 x .500)	10-878608	10-812832
23	SCREW, (.375-24 x 1.250)	10-849838	10-14000
24	NUT, (.375-24) Stainless Steel	11-8M0204726
25	ROD END	48419T01
26	ROD, Shift	495637
27	BUSHING	23-26856
28	WASHER, (.273 x .437 x .031) Stainless Steel	12-35950
29	COTTER PIN	18-25191
30	LEVER, Shift	8163677
31	STUD, (.375-24 x 1.125)	16-8M0034452	16-58152
32	KNOB	98530
33	DETENT/SPRING KIT	12016A2
34	BUSHING	23-8159831
35	WASHER	12-823970
36	WASHER, Plastic	12-824610
37	WASHER	12-814803	12-93853
38	TAB WASHER	14-8158051
39	SCREW, (M8 x 45)	10-4000357
40	CO PILOT ASSEMBLY	56-52148A08
41	PILOT ROD, (15.00 Inches)	52148002
42	NUT ASSEMBLY	11-52155A1
43	SCREW, (.250-28 x 1.00)	10-36137
44	KNOB, Prong	821621
45	ROD	873491
46	BUSHING	23-26841
47	WASHER, (.323 x .563 x .063) Stainless Steel	12-8M0042642	12-70132
48	NUT, (.312-24) Stainless Steel	11-826709111	11-45592
49	NUT, (.250-20)	11-64015
0	KEY, Ignition (1A) Comment: (1A)	894911
0	KEY, Ignition (1B) Comment: (1B)	894912
0	KEY, Ignition (1C) Comment: (1C)	894913
0	KEY, Ignition (1D) Comment: (1D)	894914
0	KEY, Ignition (1E) Comment: (1E)	894915
0	KEY, Ignition (1F) Comment: (1F)	894916
0	KEY, Ignition (2A) Comment: (2A)	894917
0	KEY, Ignition (2B) Comment: (2B)	894918
0	KEY, Ignition (2C) Comment: (2C)	894919
0	KEY, Ignition (2D) Comment: (2D)	8949110
0	KEY, Ignition (2E) Comment: (2E)	8949111
0	KEY, Ignition (2F) Comment: (2F)	8949112

Swivel Bracket and Steering Arm

Below is the parts list for Mercury 115 EFI (4-STROKE) Swivel Bracket and Steering Arm:

Position No.	Part Name	OEM Number	Supersedes
1	SWIVEL BRACKET	1400-8M0220957
2	SEAL, Oil	26-87735
3	BUSHING	23-818764	23-67669
4	O-RING	25-8M0214926
5	SPACER	23-816039
6	FITTING, Grease	22-8M0169589
7	BUSHING	23-821207	23-99608
8	SCREW, (.250-28 x .500)	10-64014
9	SWIVEL PIN ASSEMBLY	99661A35
10	LINK ROD ASSEMBLY	92876A12
11	SCREW, (.375-24 x 1.250)	10-849838	10-14000
12	NUT, (.375-24) Stainless Steel	11-8M0204726
13	WASHER, (.390 x .625 x .062) Stainless Steel	12-37828
14	BUMPER	8M0000519	881974
15	YOKE, Bottom	881914T01
16	RING, Retaining	53-67684
17	THRUST WASHER	12-816432
18	NOT SOLD SEPARATE, Decal-Serial Overlaminate	NSS
19	NOT SOLD SEPARATE, Decal-Serial Number	NSS
20	SENDER KIT, Power Trim	821400A2
21	CABLE ASSEMBLY	84-11149A58
22	SCREW, (#10-24 x .750)	10-852368	10-56682
23	LOCKWASHER, Stainless Steel	10,13-26996
24	WASHER, (.203 x .406 x .040)	12-89302
1	SWIVEL BRACKET	1400-8M0220957
2	SEAL, Oil (LOWER)	26-87735
3	BUSHING	23-818764	23-67669
4	O-RING	25-8M0214926
5	SPACER	23-816039
6	FITTING, Grease	22-8M0169589
7	BUSHING	23-821207	23-99608
8	SCREW, (.250-28 x .500)	10-64014
9	SWIVEL PIN ASSEMBLY	99661A35
10	LINK ROD ASSEMBLY	92876A12
11	SCREW, (.375-24 x 1.250)	10-849838	10-14000
12	NUT, (.375-24) Stainless Steel	11-8M0204726
13	WASHER, (.390 x .625 x .062) Stainless Steel	12-37828
14	YOKE ASSEMBLY, Bottom	42961A06
15	RING, Retaining	53-67684
16	THRUST WASHER	12-816432
17	NOT SOLD SEPARATE, Decal-Serial Overlaminate	NSS
18	BUMPER, Bottom Yoke Comment: (SALTWATER) SN# 0T979999 & Below	11288001
18	BUMPER, Bottom Yoke Comment: (SALTWATER) SN# 0T980000 & Up	11288001

Throttle Body

Below is the parts list for Mercury 115 EFI (4-STROKE) Throttle Body:

Position No.	Part Name	OEM Number	Supersedes
1	THROTTLE BODY ASSEMBLY Comment: (75)	893370T01
1	THROTTLE BODY ASSEMBLY Comment: (90)	893301T01	892490T01 (90)
1	THROTTLE BODY ASSEMBLY Comment: (115)	880129T02
2	RETAINER	891770
3	SCREW	10-891771
4	SEAL	26-891772
5	SEAL Comment: (Use with 11-1/2 IN. Cable Tie)	26-891772002
5	SEAL Comment: (Use with Oetiker Clamp)	26-891772002
6	TIE STRAP, (11.750 Inches)	54-850181
6	CLAMP, Oetiker	54-804842001
7	SCREW	10-891771001
8	WASHER	12-891773
9	WASHER	12-891773001
10	BUSHING	23-891774
11	LEVER KIT, Throttle	853659A01
12	LEVER ASSEMBLY, Throttle	858851A03
13	LOCKWASHER, External	10,13-69432
14	WASHER, Spool	12-881992
15	WASHER, Cupped	12-881991
16	SCREW, Special	10-889354
17	ROLLER	677483
18	BRACKET	891775
19	SCREW, (M6 x 16)	10-1993716
20	CABLE	8819881
21	CAM	891776
22	BUSHING	23-421621
23	WASHER, (.2656 x .625 x .0625) Stainless Steel	12-35462
24	SCREW, (M6 x 40)	10-4000333
25	COUPLER	881967
26	INDICATOR, Throttle Position	8M6005165
27	SCREW	10-891771002
28	INSERT Comment: (75)	892623002
28	INSERT Comment: (90)	892623001	892623 (90)
29	CLAMP, Oetiker	54-889691
30	CONDUIT, (.250 Inside Diameter x 3.00 Feet Bulk), Cut to 13 Inches	32-828547253

Throttle Lever and Linkage

Below is the parts list for Mercury 115 EFI (4-STROKE) Throttle Lever and Linkage:

Position No.	Part Name	OEM Number
1	LEVER ASSEMBLY, Throttle	881969A1
2	BUMPER	822458
3	BUSHING	23-812930A1
4	NOT SOLD SEPARATE, Insert	NSS
5	SCREW, (M10 x 45)	10-4007180
6	ARM ASSEMBLY, Bracket Lever	881970A2
7	SCREW, (M6 x 35) Stainless Steel	10-40011131
8	NUT, (M6) Stainless Steel	11-400212
9	CAP	42942
10	SCREW, (M6 x 16)	10-4006731
11	WASHER	12-35459
12	NUT, (M6) Stainless Steel	11-401386
1	LEVER, Throttle	878550
2	WASHER	12-84974M
3	WAVE WASHER	13-81868M
4	NUT	11-8528162
5	COLLAR	23-881378
6	WASHER	12-94524M
7	SPRING	24-804343
8	LEVER, Throttle Control	878548
9	WASHER	12-84974M
10	WAVE WASHER	13-81868M
11	BOLT, (M6 x 30)	10-881375
12	WASHER	12-35459
13	PIN, Hair	18-82053M

Tools 1

Below is the parts list for Mercury 115 EFI (4-STROKE) Tools 1:

Position No.	Part Name	OEM Number	Supersedes
1	HOLDER TOOL, Flywheel	91-8M0161873
2	FLYWHEEL PULLER	91-83164M
3	TIMING LIGHT	91-99379
4	ADAPTOR TOOL, Direct Voltage	91-890451
5	TESTER, Eight Chamber	91-850439T1
6	TACH MULTI METER, DMT 2000 Digital Comment: SN# 0T979999 & Below	91-854009A3
6	MULTI-METER KIT, DMT 2004 Comment: SN# 0T980000 & Up	91-892647A01
7	HARNESS ASSEMBLY, Crank Position Sensor Test	91-881825
8	HOLDER TOOL, Brush	91-875216
9	HARNESS ASSEMBLY, Stator Coil Test	91-881824004	91-881824, 91-881824002
10	HARNESS ASSEMBLY, Throttle Position Test	91-881827
11	HARNESS ASSEMBLY, Ignition Coil Test	91-881826
12	VACUUMMATE TOOL, Carburetor Tuner	91-8098712
13	GAUGE, Air/Fuel Pressure Comment: SN# 0T979999 & Below	91-881833A03	91-881833A 2 SN# 0T979999 & Below
13	GAUGE KIT, Air/Fuel Pressure Comment: SN# 0T980000 & Up	91-881833A03	91-881833A 2 SN# 0T980000 & Up
14	GAUGE	91-881834A1
15	NOT SOLD SEPARATE, Might Vac Vacuum Gauge Comment: (OBTAIN LOCALLY)	NSS
16	MALFUNCTION INDICATOR LAMP	99056A1
17	STARBIT TOOL KIT	91-881828
18	REMOVER/INSTALLER TOOL, Valve Guide	91-804774001	91-804774
19	REAMER TOOL, Valve Guide	91-804775
20	COMPRESSOR TOOL, Valve Spring	91-809494A1
21	NOT SOLD SEPARATE, Valve Seat Cutter Kit Comment: (OBTAIN LOCALLY)	NSS
22	WRENCH, Oil Filter Comment: SN# 0T979999 & Below	91-802653Q02	91-802653Q 1 SN# 0T979999 & Below
22	WRENCH, Oil Filter Comment: SN# 0T980000 & Up	91-802653Q02	91-802653Q 1 SN# 0T980000 & Up
23	COMPRESSOR TOOL, Piston Ring	FT2997	FJ7081, FJ8785, FJ8786, FJ8787, FJ8788, FJ8789
24	EXPANDER TOOL, Piston Ring	91-24697
25	HOLDER TOOL, Crankshaft	91-804770A1
26	INSTALLER TOOL, Driveshaft Bushing	91-875215A1
27	SOCKET, (76 mm Deep)	91-881847T	91-881847A 1

Tools 2

Below is the parts list for Mercury 115 EFI (4-STROKE) Tools 2:

Position No.	Part Name	OEM Number	Supersedes
28	SPANNER WRENCH	91-74951
29	NOT SOLD SEPARATE, Lock-Ring Pliers Comment: (SNAP-ON SRP-4)	NSS
30	NOT SOLD SEPARATE, Expanding Rod Comment: (SNAP-ON CG41-11)	NSS
31	NOT SOLD SEPARATE, Collet Comment: (SNAP-ONG CG41-12)	NSS
32	HEAT LAMP	91-63209
33	LOCATION TOOL, Pinion Comment: SN# 0T979999 & Below	91-12349A05
33	TOOL, Pinion Locating Comment: SN# 0T980000 & Up	91-12349A05
34	INSTALLATION TOOL, Bearing	91-13945
35	DRIVER TOOL, Oil Seal	91-13949
36	TOOL KIT, Bearing Race	91-14308T02
37	INSTALLATION TOOL, Bearing	91-14309T02
38	WEAR SLEEVE INSTALLATION TOOL	91-14310T1
39	PRE LOAD TOOL, Bearing Comment: SN# 0T979999 & Below	91-14311A04
39	TOOL, Preload Comment: SN# 0T980000 & Up	91-14311A04
40	MANDREL	91-15755T
41	INDICATOR TOOL, Backlash	91-196601
42	MANDREL, Bearing Driver Cup	91-31106T
43	DRIVER, Oil Seal	91-31108T
44	DRIVE HEAD TOOL	91-36569T
45	HOLDING TOOL, Driveshaft	91-804776A1
46	SHAFT	91-31229
47	NUT, (.625-18)	11-24156
48	PULLER ASSEMBLY, Slide Hammer	91-34569A1
49	DRIVER ROD TOOL, Needle Bearings	91-37323
50	PULLER PLATE	91-37241
51	MANDREL	91-37350T
52	PULLER JAW ASSEMBLY	91-46086A1
53	DIAL INDICATOR TOOL	91-58222A1
54	INDICATOR TOOL, Backlash	91-8M0053505	91-78473
55	PULLER TOOL	91-85716
56	ADAPTER KIT, Dial Indicator	91-83155
57	PULLER ASSEMBLY	91-83165T
58	INSTALLATION TOOL, Bearing	91-856875A1
59	INSTALLATION TOOL, Bearing	91-877321A1
-	SCRENCH TOOL, (10 mm), 10 MM	91-880177
-	STARBIT TOOL KIT	91-881828

Top Cowl

Below is the parts list for Mercury 115 EFI (4-STROKE) Top Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	TOP COWL ASSEMBLY Comment: (MERCURY)	100-898436T01	100-880778A15, 100-880778T03 (MERCURY)
1	TOP COWL ASSEMBLY Comment: (MARINER)	100-8M0075375
2	MOUNT Comment: SN# 0T979999 & Below	813546003	813546 2 SN# 0T979999 & Below
2	MOUNT Comment: SN# 0T980000 & Up	813546003	813546 2 SN# 0T980000 & Up
3	CAP	828716A2
4	SEAL	828352
5	SEAL	8283511
6	REAR HOOK Comment: STAINLESS STEEL	8844441
6	HOOK KIT, Rear Comment: BRONZE	892208A01
7	SCREW, (M6 x 16)	10-82130016
8	SOUND BLANKET KIT	880781A02	880781A01
9	NOT SOLD SEPARATE, Sound Blanket-Starboard	NSS
10	NOT SOLD SEPARATE, Sound Blanket-Top	NSS
11	NOT SOLD SEPARATE, Decal-Clean Cowl Cling-On	NSS
12	NOT SOLD SEPARATE, Decal-Break-In	NSS
0	DECAL SET Comment: MERCURY 75	37-895231A05
0	DECAL SET Comment: MARINER 75	37-895232A05
0	DECAL SET Comment: (MERCURY 115)(RED)	37-891814A04
0	DECAL SET Comment: (MERCURY 90)(RED)	37-891815A04
0	DECAL SET Comment: (MERCURY 115 SALTWATER)(BLUE)	37-891816A04
0	DECAL SET Comment: (MERCURY 90 SALTWATER)(BLUE)	37-891817A04
0	DECAL SET Comment: (MARINER 115)	37-891818A04
0	DECAL SET Comment: (MARINER 90)	37-891819A04
1	TOP COWL ASSEMBLY Comment: (Black)	4021-827328T9
1	TOP COWL ASSEMBLY Comment: (Silver)	4021-827328T10
2	INLET, Air - Black Comment: (Black)	821256T03	821256T 1 (Black)
2	INLET, Air - Silver Comment: (Silver)	821256T2
3	SCREW, (M6 x 16)	10-82130016
4	SOUND BLANKET KIT	859356A02	859356A 1
5	NOT SOLD SEPARATE, Sound Blanket-Port	NSS
6	NOT SOLD SEPARATE, Sound Blanket-Starboard	NSS
7	NOT SOLD SEPARATE, Sound Blanket-Back	NSS
8	CAP PLUG	19-823865
9	HANDLE	831207A16	831207A14, 831207T 3, 831207T10
10	BUSHING	23-812707	23-71984, 23-F286818, 23-F286828, F480818
11	SPACER	23-831214
12	WASHER, Wave	13-12134
13	CAM, Latch Shaft Comment: SN# 0T979999 & Below	8M0001081	889566, F481777, F48177 SN# 0T979999 & Below
13	CAM Comment: SN# 0T980000 & Up	8M0001081	889566, F481777, F48177 SN# 0T980000 & Up
14	WASHER	12-8M0214930
15	SCREW, (M6 x 16)	10-1993716
16	BRACKET, Front	8M0036792	821249M 2
17	BUMPER, Latch	815477
18	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
19	NUT, (M6) Stainless Steel	11-401366
20	RING, Retaining	53-8237951
21	ROLLER	8M0207770
22	PIN, Roll	8155381
23	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
24	NUT, (M6) Stainless Steel	11-401366
25	ROPE AND HANDLE KIT, Manual Starting	47341A11
26	ROPE	50-12066Q10
0	DECAL SET Comment: (Black-Long)(Tracker)(2004)	37-881649A01
0	DECAL SET Comment: (Black-Long)(Tracker)(2005)	37-881649A05
0	DECAL SET Comment: (Black-X-Long)(Saltwater-Red)	37-881649A05
0	DECAL SET Comment: (Black-X-Long)(Saltwater-Blue)(2004)	37-881840A03	37-881840A01 (Black-X-Long)(Saltwater-Blue)(2004)
0	DECAL SET Comment: (Black-X-Long)(Saltwater-Blue)(2005)	37-881840A05
0	DECAL SET Comment: (Gray)	37-881650A03	37-881650A01 (Gray)

Transom Bracket

Below is the parts list for Mercury 115 EFI (4-STROKE) Transom Bracket:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET, Transom (Starboard)	3426-828334T02	3426-828334F 1
2	BRACKET ASSEMBLY, Transom (Port)	3425-828333T07	3425-828333A 3
3	FITTING, Grease (Port)	22-8M0169588
4	TUBE KIT, Tilt Comment: (Carbon Steel)	99170A2
4	TILT TUBE Comment: (Stainless Steel)	826125A1
5	NUT, (1.00-14) Comment: (Use with Carbon Steel Tilt Tube)	11-859133	11-34862, 11-90068F 3, 11-90068F 4 (Use with Carbon Steel Tilt Tube)
5	NUT, (1.00-14) Brass/Nickel Plate Comment: (Use with Stainless Steel Tilt Tube)	11-826135
6	O-RING, (.612 x .103)	25-45711
7	WASHER	13-88750
8	NUT, (.875-14) Comment: (Use with Carbon Steel Tilt Tube)	11-858869	11-30499 (Use with Carbon Steel Tilt Tube)
8	NUT, (.875-14) Comment: (Use with Stainless Steel Tilt Tube)	11-826164
9	SCREW, (.500-20 x 4.500)	10-8M0149747
10	WASHER, (.530 x .870 x .105) Stainless Steel	12-8M0204665
11	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
12	NUT, (.500-20)	11-82671117
13	SPRING, Tension	24-830899
14	LEVER ASSEMBLY, Tilt Lock	8M0109798	821176T02, 821176T 1
15	NYLINER	23-65830
16	SPRING, Compression	24-830900
17	KNOB	99633
18	PIN, Groove	17-99615
19	PIN	17-893709	17-99617
20	BRACKET, Anchor	8M0086406	818771T 1
21	SCREW, (M10 x 30)	10-858771
22	WASHER	12-4002319
23	NUT, (M10)	11-40114
24	ANODE KIT	97-818298T1
25	SCREW, (M6 x 25)	10-8M0204707
26	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
27	CLIP	54-22740
28	C WASHER	8M0084613	69205
29	SCREW, (#10-16 x .600)	10-878609	10-812832 1
1	BRACKET, Transom Comment: (STARBOARD)	3426-828334T02	3426-828334F 1 (STARBOARD)
2	BRACKET ASSEMBLY, Transom Comment: (PORT)	3425-828333T07	3425-828333A 3 (PORT)
3	FITTING, Grease Comment: (PORT)	22-8M0169588
4	TUBE KIT, Tilt	99170A2
4	TILT TUBE Comment: (STAINLESS STEEL)	826125A1
5	NUT, (1.00-14)	11-859133	11-34862, 11-90068F 3, 11-90068F 4
5	NUT, (1.00-14) Nylon Insert Comment: (Use With Stainless Steel Tilt Tube)	11-826135
6	O-RING, (.612 x .103)	25-45711
7	WASHER	13-88750
8	NUT, (.875-14)	11-858869	11-30499
8	NUT, (.875-14) Comment: (Use With Stainless Steel Tilt Tube)	11-826164
9	SCREW, (.500-20 x 4.500)	10-8M0149747
10	WASHER, (.530 x .870 x .105) Stainless Steel	12-8M0204665
11	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
12	NUT, (.500-20)	11-82671117
13	SPRING, Tension	24-830899
14	LEVER ASSEMBLY, Tilt Lock	8M0109798	821176T02, 821176T 1
15	NYLINER	23-65830
16	SPRING, Compression	24-830900
17	KNOB	99633
18	PIN, Groove	17-99615
19	PIN	17-893709	17-99617
20	BRACKET, Anchor	8M0086406	818771T 1
21	SCREW, (M10 x 30)	10-858771
22	WASHER	12-4002319
23	NUT, (M10 x 1.5)	11-40114
24	ANODE KIT	97-818298Q1
25	SCREW, (M6 x 25)	10-8M0204707
26	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
27	CLIP	54-22740
28	C WASHER	8M0084613	69205
29	SCREW, (#10-16 x .600)	10-878609	10-812832 1

Vapor Separator

Below is the parts list for Mercury 115 EFI (4-STROKE) Vapor Separator:

Position No.	Part Name	OEM Number	Supersedes
-	VAPOR SEPARATOR ASSEMBLY	880133T12	880133T07, 880133T06, 880133T11
1	COVER KIT	889317T1
2	NOT SOLD SEPARATE, Seat	NSS
3	PLATE, Baffle	889318001	889318
4	SCREW, (M6 x 16)	10-883223
5	GASKET	27-889319	27-889319001
6	FITTING	22-883556
7	O-RING	25-8M0062785	25-883209
8	FITTING	22-889329
9	PLUG	19-883208	19-881830
10	FILTER, Fuel	35-8M0122423
11	FLOAT KIT	889320A1
12	SHAFT	F10064
13	PUMP ASSEMBLY, Fuel - High Pressure	888725T02
14	SLEEVE	8M6000589	23-855428
15	O-RING	25-8893162
16	SEAL	26-889321
17	RETAINER	889328
18	SCREW	1395-9643
19	PUMP ASSEMBLY, Boost	888733T02	888733T 1
20	GROMMET	25-889322
21	O-RING	25-889316
22	SEAL	26-8M6001413	26-889323
23	BOWL KIT	889324T03	889324T02
24	WIRE	84-889325A02	84-889325A 1
25	NOT SOLD SEPARATE, Check Valve	NSS
26	FITTING	22-855424011
27	VALVE KIT, Inlet	889326A1
28	SCREW, Drian	10-889327A1
29	O-RING	25-8893161
30	SENSOR, Water	8M0214989
31	FITTING, Elbow 45 Degree (1.25)	22-782792
32	O-RING, (.301 x .070)	25-627021
33	INSERT	889430
34	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275

Vapor Separator/Fuel Rail Mounting

Below is the parts list for Mercury 115 EFI (4-STROKE) Vapor Separator/Fuel Rail Mounting:

Position No.	Part Name	OEM Number	Supersedes
1	STUD, (M10 x 91)	16-8M0063255
2	NUT, (M10) Brass/Nickel Plated	11-826292
3	INJECTOR ASSEMBLY, Air Comment: SN# 0T979999 & Below	8M6001744	8M0065917, 884595A01, 884595A 1, 884595A02 SN# 0T979999 & Below
3	INJECTOR ASSEMBLY, Air Comment: SN# 0T980000 & Up	8M6001744	8M0065917, 884595A01, 884595A 1, 884595A02 SN# 0T980000 & Up
4	WASHER ASSEMBLY, Cupped	12-828694A1
5	SPACER	23-883050
6	GROMMET Comment: SN# 0T979999 & Below	25-855362001	25-855362 SN# 0T979999 & Below
6	GROMMET Comment: SN# 0T980000 & Up	25-855362001	25-855362 SN# 0T980000 & Up
7	WASHER	12-4002318
8	SCREW, (M8 x 60)	10-82446060
9	SCREW, (M8 x 35)	10-82446035
10	BUSHING	23-855364

Water Hoses

Below is the parts list for Mercury 115 EFI (4-STROKE) Water Hoses:

Position No.	Part Name	OEM Number	Supersedes
1	STRAINER	35-8348084
2	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
3	HOSE Comment: SN# 0T979999 & Below	32-883060001	32-883060 SN# 0T979999 & Below
3	HOSE Comment: SN# 0T980000 & Up	32-883060001	32-883060 SN# 0T980000 & Up
4	HOSE, (17.00 Inches Bulk) (Cut to 10-1/2 Inches)	32-85833939
5	HOSE, (17.00 Inches Bulk) (Cut to 6-1/2 Inches) To Telltale	32-85833939

Download this page as PDF: Click here

For Mercury Owners:

To assist you in maintaining and repairing your marine engines, we hope the following resources may be of use:

Mercury / Mercruiser / Mariner Parts from JLM Marine

About JLM Marine

Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.

As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.

We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.