Mercury 125 (4 CYL.) (0T980000 THRU 0T999999) Outboard Motor Parts Diagram & Catalog – Free PDF Download

by JLM Marine 30 Apr 2025 0 Comments

Mercury 125 (4 CYL.) Outboard Motor Parts Diagram & Catalog – Free PDF Download

Accessories

Below is the parts list for Mercury 125 (4 CYL.) Accessories:

Position No.	Part Name	OEM Number	Supersedes
-	ANTI-ICING KIT, Carburetor	828155A5
-	EXTENSION KIT (5 Inch) Comment: (Not for use on Jet Model Outboards)	12092A13
-	FLUSHING ATTACHMENT Comment: (Not for use on Jet Model Outboards)	44357Q2
-	HOSE ASSEMBLY, Fuel (8 Feet) Comment: (With Quck Disconnect)	32-877680Q8
-	HOSE ASSEMBLY, Fuel (12 Feet) Comment: (With Quck Disconnect)	32-877680Q12	32-858620Q12, 32-858620A12, 32-827927A12 (With Quck Disconnect)
-	HOSE ASSEMBLY, Fuel (8 Feet) Comment: (With Quck Disconnect Engine End Only)	32-877681Q8
-	HOSE ASSEMBLY, Fuel (12 Feet) Comment: (With Quck Disconnect Engine End Only)	32-877681Q12	32-804792Q12, 32-804792Q, 32-858621Q12, 32-858621A12, 32-17146A12 (With Quck Disconnect Engine End Only)
-	HOSE ASSEMBLY, Fuel (12 Feet) Comment: (No Fittings)	32-877683Q12	32-858623Q12, 32-858623A12, 32-822379A12, 32-819380A12, FA599752, FS409752, 32-819380A 3, F216752, FA409752, F289752, FA178752, FA216752, FA284752, FA289752, FS409952 (No Fittings)
-	MERCATHODE KIT	88334A2
-	TILLER HANDLE ADAPTOR KIT Comment: (Jet 80)	850000A3
-	TILLER HANDLE KIT	12022A41
-	VISUAL WARNING SYSTEM (Low Oil/Overheat)	17334A2
-	REGULATOR KIT, Voltage	88825A6
-	FLUSH KIT, Coastal	858566A1

Attenuator Plate

Below is the parts list for Mercury 125 (4 CYL.) Attenuator Plate:

Position No.	Part Name	OEM Number	Supersedes
1	GASKET	27-151724
2	COVER	44342A1
3	CAP	19-815784	22-14685
4	NOT SOLD SEPARATE, Timing	NSS
5	NOT SOLD SEPARATE, Decal-Caution-Airbox	NSS
6	GASKET	27-828479
7	SCREW, (#10-16 x .600)	10-878609	10-812832 1
8	PLATE ASSEMBLY, Attenuator	44340A2
9	WASHER	12-4002217
10	NUT	11-826365
11	CUP	39519
12	LATCH	98889
13	HOSE, (.187) (26.00 Inches Bulk) (Cut to 1.50 Inch Length)	32-9912878
14	HOSE, (.187) (26.00 Inches Bulk) (Cut to 3.25 Inch Length)	32-9912878
15	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
15	TIE STRAP, (5.50 Inches)	8M0214940
16	FITTING TEE	22-830285
17	HOSE, (.187) (26.00 Inches Bulk) (Cut to 5.25 Inch Length)	32-9912878
18	LINK, Throttle (Main)	825203T	825203
19	LINK ROD	193859
20	ARM ASSEMBLY	11399A1
21	SCREW, (M5 x 6)	10-40056103
22	WASHER, (.203 x .500 x .032)	12-8M0204666
23	ROLLER	67748
-	GASKET SET	27-13461A99

Bleed System

Below is the parts list for Mercury 125 (4 CYL.) Bleed System:

Position No.	Part Name	OEM Number	Supersedes
1	TUBING, (240.00 Inches Bulk) Comment: (Cut to 9.00 Inch Length)	32-892024122	32-99130122 (Cut to 9.00 Inch Length)
2	FITTING, Tee	22-59169003
3	TUBING, (240.00 Inches Bulk) Comment: (Cut to 9.00 Inch Length)	32-892024122	32-99130122 (Cut to 9.00 Inch Length)
4	TUBING, (240.00 Inches Bulk) Comment: (Cut to 4.50 Inch Length)	32-892024122	32-99130122 (Cut to 4.50 Inch Length)
5	TUBING, (240.00 Inches Bulk) Comment: (Cut to 2.50 Inch Length)	32-892024122	32-99130122 (Cut to 2.50 Inch Length)
6	CHECK VALVE	21-149126
7	TUBING, (240.00 Inches Bulk) Comment: (Cut to 2.50 Inch Length)	32-892024122	32-99130122 (Cut to 2.50 Inch Length)
8	TUBING, (240.00 Inches Bulk) Comment: (Cut to 2.50 Inch Length)	32-892024122	32-99130122 (Cut to 2.50 Inch Length)
9	TUBING, (240.00 Inches Bulk) Comment: (Cut to 4.50 Inch Length)	32-892024122	32-99130122 (Cut to 4.50 Inch Length)
10	TUBING, (240.00 Inches Bulk) Comment: (Cut to 2.50 Inch Length)	32-892024122	32-99130122 (Cut to 2.50 Inch Length)
11	TUBING, (240.00 Inches Bulk) Comment: (Cut to 2.50 Inch Length)	32-892024122	32-99130122 (Cut to 2.50 Inch Length)
12	TUBING, (240.00 Inches Bulk) Comment: (Cut to 2.50 Inch Length)	32-892024122	32-99130122 (Cut to 2.50 Inch Length)
13	TUBING, (240.00 Inches Bulk) Comment: (Cut to 6.00 Inch Length)	32-892024122	32-99130122 (Cut to 6.00 Inch Length)
14	TUBING, (240.00 Inches Bulk) Comment: (Cut to 1.50 Inch Length)	32-892024122	32-99130122 (Cut to 1.50 Inch Length)
15	FITTING	22-15133
-	POWERHEAD ASSEMBLY	17791T97

Bottom Cowl

Below is the parts list for Mercury 125 (4 CYL.) Bottom Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	BOTTOM COWL ASSEMBLY, Starboard	100-8M0107327
2	GROMMET	25-822556003	25-822556 2
3	SEAL, (36.00 Inches)	8M0109216
4	BOTTOM COWL ASSEMBLY, Port	100-8M0107328	2188-821874A 1
5	GROMMET	25-822555001	25-822555
6	SEAL, (36.00 Inches)	8M0109216
7	SEAL	8560552
8	SWITCH ASSEMBLY	87-8M0042301	87-896620, 87-856990, 87-850691, 87-18286A40
9	FITTING	22-813613
10	TUBING, (.312) (70.00 Inches Bulk) (Cut to 28.00 Inch Length)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
11	CHECK VALVE ASSEMBLY, Drain	21-817519A2
12	SCREW, (M6 x 40)	10-82130040
13	HANDLE	8M0041366	820000A 2
14	BUSHING	23-812707	23-71984, 23-F286818, 23-F286828, F480818
15	WASHER, Wave	13-F2047
16	CAM	8M0001081	889566, F481777, F48177
17	WASHER	12-8M0214930
18	LOCKWASHER, (.250) Stainless Steel	13-26992
19	SCREW, (.250-20 x .620) Stainless Steel	10-28635
20	RETAINER	822363T1
21	NUT, (M6) Stainless Steel	11-401386
22	WASHER	12-8M0214930

Carburetor

Below is the parts list for Mercury 125 (4 CYL.) Carburetor:

Position No.	Part Name	OEM Number	Supersedes
1	CARBURETOR, (WME 111-1) (115)	3301-884586T07	3301-884586T 1
1	CARBURETOR, (WME 111-2) (115)	3301-884586T08	3301-884586T 2
1	CARBURETOR, (WME 111-3) (115)	3301-884586T09	3301-884586T 3
1	CARBURETOR, (WME 111-4) (115)	3301-884586T10	3301-884586T 4
1	CARBURETOR, (125-WME 112-1)	3301-884587T07	3301-884587T 1
1	CARBURETOR, (125-WME 112-2)	3301-884587T08	3301-884587T 2
1	CARBURETOR, (125-WME 112-3)	3301-884587T09	3301-884587T 3
1	CARBURETOR, (125-WME 112-4)	3301-884587T10	3301-884587T 4
2	NOT SOLD SEPARATE, Gasket-Fuel Bowl	NSS
3	NOT SOLD SEPARATE, Retaining Ring	NSS
4	BOWL, Fuel	1395-811693	1395-9590
5	SHAFT, Throttle (WME-111-1/3/4 and WME 112-1/3/4)	1395-823632
6	SHAFT, Throttle (WME-111-2 and WME 112-2)	1395-8236321
7	LEVER, Throttle	1395-8087461
8	VALVE, Throttle	1395-97241
9	FLOAT	1395-9594
10	SHAFT	F10064
11	VALVE, Inlet Needle	10-95951
12	PLUG KIT	1395-811694	1395-9596 1
13	SEAL (Consists of 4 Seals)	1395-802731
14	NOT SOLD SEPARATE, Gasket-Cover Plate	NSS
15	GASKET	27-151724
16	SCREW, Throttle Valve	10-F10155
17	SCREW, Cover Plate	1395-811220
18	SCREW AND WASHER, (#8-32 x .750)	1395-808612	1399-5132
19	COVER PLATE	1395-811221
20	JET, Main (.060) (WME-111-1/3/4)(115)	1395-6487
20	JET, Main (.062) (WME-111-2)(115)	1399-4217
20	JET, (.070) (WME-112-1)(125)	1395-6030
20	JET, (.078) (WME-112-2)(125)	1395-6680
20	JET, (.076) (WME-112-3/4)(125)	1399-3796
21	GASKET	1395-808738
22	NOT SOLD SEPARATE, Spring-Idle Needle	NSS
23	NOT SOLD SEPARATE, Spring-Throttle Return	NSS
24	NOT SOLD SEPARATE, Idle Needle	NSS
25	SCREW	1395-823634
-	REPAIR KIT, Carburetor Comment: (1 Per Carburetor)	1395-8236354
-	GASKET SET, Carburetor Comment: (1 Per Carburetor)	1395-8112231
-	GASKET SET	27-13461A99

Co-Pilot

Below is the parts list for Mercury 125 (4 CYL.) Co-Pilot:

Position No.	Part Name	OEM Number	Supersedes
-	CO-PILOT ASSEMBLY	56-52148A7
1	PILOT ROD	521481
2	NUT ASSEMBLY	11-8M0103848
3	SCREW, (.250-28 x 1.250)	10-56500
4	WASHER	12-77674
5	KNOB, Prong	821621
6	ROD	873491
7	BUSHING	23-521512
8	WASHER, (.323 x .563 x .063) Stainless Steel	12-8M0042642	12-70132
9	NUT, (.312-24) Stainless Steel	11-826709111	11-45592

Crankshaft, Pistons and Connecting Rods

Below is the parts list for Mercury 125 (4 CYL.) Crankshaft, Pistons and Connecting Rods:

Position No.	Part Name	OEM Number	Supersedes
1	CRANKSHAFT ASSEMBLY	473-9193T5
2	GEAR ASSEMBLY	43-43019A1
3	BEARING, Ball, Lower	30-43011T
4	KEY, Woodruff	28-91800
5	WEAR SLEEVE	786611
6	O-RING, (.859 x .139)	25-35126
7	RING ASSEMBLY	39-818412A4
8	BEARING ASSEMBLY, Roller	42943A1
9	NOT SOLD SEPARATE, Roller Bearing	NSS
10	PISTON ASSEMBLY Comment: (Standard)	2704-826191T4
10	PISTON ASSEMBLY Comment: (.015 Oversize)	2704-821896A3
10	PISTON ASSEMBLY Comment: (.030 Oversize)	2704-821896A4
11	NOT SOLD SEPARATE, Piston Pin	NSS
12	LOCK RING	53-857196	40-52035
13	RING KIT, Piston - Standard Comment: (Standard)	39-822321A12	39-822321A 8, 39-824905A12 (Standard)
13	RING KIT, Piston - .015 Oversize Comment: (.015 Oversize)	39-822321A1
13	RING SET, Piston Comment: (.030 Oversize)	39-822321A2
14	CONNECTING ROD ASSEMBLY	646-818846T6
15	WASHER	12-8M0012298	12-812876
16	BEARING, Needle	29-8M0214954
17	SCREW, (.375-24 x 1.250)	10-94320
18	BEARING ASSEMBLY	31-844338A01	31-43012A04
19	NOT SOLD SEPARATE, Roller Bearing	NSS
20	BEARING ASSEMBLY, Roller, Upper	31-43013T3
21	SEAL, Oil	26-8M0214932
22	O-RING Comment: (2.112 x .103 Square)	25-858225
22	O-RING, (1.989 x .070) Comment: (1.989 x .070 Round)	25-823683	25-64067 (1.989 x .070 Round)
-	GASKET SET	27-13461A99
-	POWERHEAD ASSEMBLY	17791T97

Cylinder Block and Crankcase

Below is the parts list for Mercury 125 (4 CYL.) Cylinder Block and Crankcase:

Position No.	Part Name	OEM Number	Supersedes
1	CYLINDER BLOCK	877-9191T24
2	SCREW, (M10 x 80)	10-4009680
3	PIN (Bearing Race)	17-8M0036405	17-67296
4	PIN, Dowel	17-43044
5	COVER (Top)	428842
6	COVER (Bottom)	76867
7	SCREW, (M8 x 50)	10-81742750
8	CARRIER	65848
9	GROMMET	25-64872
10	CARRIER ASSEMBLY	813801A1
11	CHECK VALVE	21-42657A3
12	CHECK VALVE	21-891664	21-14653 3
13	STUD, (M10 x 136)	16-892561001	16-889607
14	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963
15	NUT, (M10)	11-40140
16	CHECK VALVE	21-426233
17	NOT SOLD SEPARATE, Plug	NSS
18	NOT SOLD SEPARATE, Plug	NSS
19	WASHER, (.203 x .500 x .032)	12-8M0204666
20	SCREW, (M8 x 35 MM)	10-82127335
21	BOOT	99162001
22	COVER	1035-9196A2
23	GASKET	27-443284
24	SCREW, (M8 x 35 MM)	10-82127335
25	CLAMP	54-814634
26	SENDER, Temperature	787992
27	RETAINER	889733	44552
28	SCREW, (#10-16 x .600)	10-878609	10-812832 1
29	POPPET VALVE	86596T
30	DIAPHRAGM	648771
31	WASHER	12-94182
32	SCREW, (#10-16 x .750)	10-69570
33	SPRING, (Stainless Steel)	24-42996
34	THERMOSTAT	14586
35	GASKET	27-8M0204714
36	GASKET	27-430068
37	COVER	8M0047619	884297, 42885 3
38	SCREW, (M8 x 35 MM)	10-82127335
38	SCREW, (M8 x 55)	10-81742755
39	PLUG, Pipe (.125-27) Brass	22-328022
40	STUD, (M6 x 44)	16-8161949
41	WASHER, (.187 x .500 x .062) Neoprene	12-8M0204663
42	WING NUT	11-816872
43	REV LIMITER	821889A51	821889A40, 821889A29, 821889A19
44	SCREW, (M6 x 30)	10-82130030
45	HARNESS ASSEMBLY, Adaptor	84-855212A1
46	COUPLING INSERT	22-857175	22-861405
47	COUPLING BODY	22-857176
48	CAP	19-858240	861427
49	TUBING, (.312) (70.00 Inches Bulk)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
50	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
51	FITTING	22-857219
52	FITTING	22-286241
53	TIE STRAP, (11.750 Inches)	54-850181
54	NOT SOLD SEPARATE, Decal-Serialization	NSS
55	NOT SOLD SEPARATE, Decal-Serial Overlaminate	NSS
-	GASKET SET	27-13461A99
-	POWERHEAD ASSEMBLY	17791T97

Driveshaft Housing

Below is the parts list for Mercury 125 (4 CYL.) Driveshaft Housing:

Position No.	Part Name	OEM Number	Supersedes
1	HOUSING ASSEMBLY, Driveshaft	1598-881913T01
1	HOUSING ASSEMBLY, Driveshaft Comment: Jet	1598-881913T02
2	STUD, (M10 x 100) (Long) Comment: Model Version Length Designation: Long =20 In.	16-903501
2	STUD, (M10 x 227) (X-Long) Comment: Model Version Length Designation: X-Long=25 In.	16-9035015
3	STUD, (M10 x 63) (Long) Comment: Model Version Length Designation: Long =20 In.	16-9035012
3	STUD, (M10 x 190) (X-Long) Comment: Model Version Length Designation: X-Long=25 In.	16-8M0034462	16-90350 16 Model Version Length Designation: X-Long=25 In.
4	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963
5	NUT, (M10)	11-40140
6	PICKUP ASSEMBLY, Speedometer	22-85822A4
7	CONNECTOR, 90 Degree - With Vibraseal	22-433351
8	CONNECTOR, Straight	22-85822T
9	MOUNT	881916
10	BOLT, (M12 x 154)	10-898835001	10-42973
11	WASHER, (.875 Inch Outside Diameter)	12-30119
12	NUT, (M12)	11-8M0204662
13	CABLE ASSEMBLY, Ground	88238A10
14	SCREW, (.250-20 x .500) Stainless Steel	10-41508
15	CLAMP	8M0036786	881917
16	NUT	11-35521
17	SCREW, (M8 x 25 MM)	10-889833025
18	COVER	100-8M4500754	8M0000852, 882752
19	SCREW, (#12-24 x .620)	10-88417
20	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
21	WASHER, Neoprene	12-881976
22	SPACER KIT (X-Long) Comment: Model Version Length Designation: X-Long=25 In.	12092A3
23	PIN, Dowel - Without Hole (.375 x .625) (X-Long) (Rear) Comment: Model Version Length Designation: X-Long=25 In.	17-43044
23	PIN, Dowel - With Hole (.375 x .625) (X-Long)(Front) Comment: Model Version Length Designation: X-Long=25 In.	17-8M0084244	17-43043 Model Version Length Designation: X-Long=25 In.
24	PLATE WASHER	892214
25	PLUG, Driveshaft Housing	19-8M0026580	19-889557

Electrical Components

Below is the parts list for Mercury 125 (4 CYL.) Electrical Components:

Position No.	Part Name	OEM Number	Supersedes
1	PLATE, Electrical	8327531
2	SCREW, (M8 x 30) Stainless Steel	10-40011150
3	WASHER	12-49436
4	BUSHING	23-8502341
5	GROMMET	25-833155
6	SCREW, (M5 x 12)	10-82239312
7	WASHER, (.203 x .406 x .040)	12-89302
8	CLAMP, Connector	8261151
9	CABLE ASSEMBLY (10.00 Inches)	84-88807A44
10	HARNESS ASSEMBLY, Engine	84-850043A2
11	FUSE, Yellow - 20 Ampere	88-812619	88-860608
12	HARNESS ASSEMBLY, Ignition	84-850045A2
13	CABLE ASSEMBLY, Positive - Battery	84-88439A3
14	BOOT, Insulator - Red	85-830233
15	CDM MODULE ASSEMBLY	827509A10	827509A 4
16	CABLE ASSEMBLY, Hi Tension	84-821945A61
17	BOOT/TERMINAL KIT	85-63709A1
18	SPARK PLUG Comment: (NGK #BP8H-N-10)	33-816737Q	33-816737 2 (NGK #BP8H-N-10)
18	SPARK PLUG Comment: (NGK #BPZ8H-N-10)	33-938
19	SCREW, (M6 x 16)	10-82129116
20	SOLENOID ASSEMBLY, (#10-32 / .3125-18 Terminals)	89-817109A2
21	BUSHING	23-8M0214955
22	GROMMET	25-822179
23	NUT, Brass	10-32,11-45076
24	LOCKWASHER, (.312)	13-8M0204647
25	NUT, (.312-18)	11-8M0204668
26	SCREW, (M6 x 25 MM)	10-82129125
27	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
28	REGULATOR, Voltage	8M0084173	883072T, 854515T 1
29	SCREW, (M6 x 35)	10-82129135
30	J CLIP	54-54457
31	CABLE ASSEMBLY, Battery - Negative	84-88439A4
32	CLAMP	54-834813
33	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
33	TIE STRAP, (4.00 Inches)	56762
34	WASHER	12-36001
35	CABLE ASSEMBLY, (4.00 Inches) Black	84-88807A16
36	PLUG, Male	13541

Exhaust Plate

Below is the parts list for Mercury 125 (4 CYL.) Exhaust Plate:

Position No.	Part Name	OEM Number	Supersedes
1	PLATE, Exhaust	881912T01
2	PIN, Dowel	17-23784
3	RETAINER	881973
4	MOUNT	881915002	881915001
5	SCREW, (M8 x 35 MM)	10-881975
6	BOLT, (M12 x 175)	10-898487	10-42974
7	NUT, (M12)	11-896963	11-859129, 11-90099
8	SPACER (Long) Comment: Model Length Designation Long=20 In.	23-813745	23-43041 Model Length Designation Long=20 In.
8	SPACER (X-Long) Comment: Model Length Designation X Long=25 In.	23-11289
9	COUPLING	43585
10	GASKET	27-430086
11	TUBE, Exhaust	42966T07
12	SCREW, (M8 x 35) Stainless Steel	10-40011151
13	SEAL	8M0039075	42962
14	GROMMET	25-89417004
15	TUBE, Water - Long (13.21 Inches)	32-8M0042791	32-881201 1
15	TUBE, Water - X Long (18.21 Inches)	32-8M0042792	32-881201 2
16	CLAMP	824661
17	SEAL (Upper)	814080001	814080
18	SCREW, (M8 x 45)	10-889833045
19	CLAMP	881918T03	881918T02, 881918T
20	GROMMET	25-19565002
21	BUSHING	23-48237
22	SHIFT SHAFT ASSEMBLY	79932A20
23	SHIFT LINK	42912A3
24	BUSHING	23-48475
25	NUT, (M6) Stainless Steel	11-401386
26	SCREW, (M8 x 35) Stainless Steel	10-40011151
27	SCREW, (M8 x 70) Stainless Steel	10-40011158

Extension Kit

Below is the parts list for Mercury 125 (4 CYL.) Extension Kit:

Position No.	Part Name	OEM Number	Supersedes
-	EXTENSION KIT, Black	12092A13
1	SPACER KIT, Black	12092A3
2	PIN, Dowel - Without Hole (.375 x .625)	17-43044
2	PIN, Dowel - With Hole (.375 x .625)	17-8M0084244	17-43043
3	SHIFT SHAFT ASSEMBLY	853908A1
4	BUMPER, Bottom Yoke	11288001
5	SPACER	23-11289
6	TUBE ASSEMBLY, Water - Extension	17243A1
7	O-RING, (.796 x .139)	25-8M0204645
8	SEAL	26-38970
9	STUD, (M10 x 190)	16-903503
10	STUD, (M10 x 227)	16-903502
11	WASHER, (.453 x .812 x .105) Stainless Steel	12-45176
12	NUT, (M10)	11-40140
13	DRIVESHAFT ASSEMBLY	45-43032A4
14	GASKET, Aluminum Cover	27-430341
15	O-RING, (3.609 x .139)	25-8M0214974
16	O-RING, (1.424 x .103)	25-8M0204681
17	BUMPER, Top Yoke	88882
18	TUBE, Water	32-8M4501430	32-828937 1
19	SEAL	430232

Flywheel and Starter Motor

Below is the parts list for Mercury 125 (4 CYL.) Flywheel and Starter Motor:

Position No.	Part Name	OEM Number	Supersedes
1	PLUG, Yellow	19-45907
2	COVER ASSEMBLY	812777T1
3	NUT, (M16)	11-42979
4	WASHER	12-33001
5	FLYWHEEL ASSEMBLY	261-878227T2
6	STATOR ASSEMBLY	398-832075A21	398-832075A 4
-	CABLE ASSEMBLY	84-11149A27
7	SCREW, (M5 x 30)	10-4013930
8	TRIGGER ASSEMBLY	854513T	834821T
9	STARTER MOTOR ASSEMBLY	50-893892T	50-66015 3
9	STARTER MOTOR ASSEMBLY	50-893892T	50-66015 3
10	COLLAR	23-8M0034918	23-8M0001391, 56703
11	STOP, Rubber	8M0043376	68042
12	CABLE ASSEMBLY, (6.00 Inches) Black	84-93388A1
13	SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel	10-69035
14	CABLE ASSEMBLY, (12.5 Inchs) Black	84-93388A8
15	LOCKWASHER, (.250) Stainless Steel	13-26992
16	NUT, (.250-20)	11-64015
17	TIE STRAP, (4.00 Inches)	56762
17	TIE STRAP, (5.50 Inches)	8M0214940
17	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
18	SWIVEL BASE	93254
19	SWIVEL BALL	93421
20	NOT SOLD SEPARATE, Decal-Warning High Voltage	NSS
21	DECAL, Caution-Start in Gear (Start In Gear)	37-881865	37-825064

Fuel Pump

Below is the parts list for Mercury 125 (4 CYL.) Fuel Pump:

Position No.	Part Name	OEM Number	Supersedes
1	PUMP KIT, Fuel	14360A78
2	DIAPHRAGM KIT	21-857005A1
3	NOT SOLD SEPARATE, Gasket-Boost	NSS
4	NOT SOLD SEPARATE, Diaphragm	NSS
5	NOT SOLD SEPARATE, Gasket-Pulse	NSS
6	NOT SOLD SEPARATE, Spring	NSS
7	NOT SOLD SEPARATE, Cap	NSS
8	NOT SOLD SEPARATE, Check Valve	NSS
9	NOT SOLD SEPARATE, Retainer	NSS
10	NOT SOLD SEPARATE, Spring	NSS
11	NOT SOLD SEPARATE, Cap	NSS
12	GASKET	27-8M0204705
13	BASE	144303
14	PLATE	987752
15	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
16	SCREW, (M5 x 40)	10-82104540
17	SCREW, (M6 x 50), Pump To Block	10-82130050
18	NOT SOLD SEPARATE, Decal-Assembled in Mexico	NSS
19	TUBING, (.312) (70.00 Inches Bulk) (Cut to 4.00 Inch Length)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
20	TUBING, (.312) (70.00 Inches Bulk) (Cut to 8.50 Inch Length)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
21	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon (To Crankcase)	22-996642
22	TUBING, (.312) (70.00 Inches Bulk) (Cut to 2.00 Inch Length)	32-8M0108349	32-8M0047448, 32-830757130, 32-830757 80
23	FILTER, Fuel	35-816296Q2
24	CLAMP	54-188871
25	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
25	TIE STRAP, (5.50 Inches)	8M0214940
26	CHECK VALVE (To Oil Pump)	22-8189941
27	MOLDED HOSE	32-822554
28	CONNECTOR	22-822771
29	CONNECTOR	22-822769
30	TUBING, (26.00 Inches Bulk) (Cut to 4.00 Inch Length)	32-85682257
31	GROMMET	25-145093
32	TUBING, (38.00 Inches Bulk) (Cut to 15.00 Inch Length)	32-1430165
33	FLOW RESTRICTOR	19-17608
34	FITTING, Tee	22-830570	22-17768
35	TUBING, (240.00 Inches Bulk) (Cut to 4.50 Inch Length)	32-892024122	32-99130122
36	TUBING, (240.00 Inches Bulk) (Cut to 2.50 Inch Length)	32-892024122	32-99130122
37	TUBING, (38.00 Inches Bulk) (Cut to 1.25 Inch Length)	32-1430165
38	FILTER	35-8M0207786
39	TUBING, (38.00 Inches Bulk) (Cut to 13.00 Inch Length)	32-1430165
40	PUMP ASSEMBLY, Accelerator	14687A4
41	TUBING, (36.00 Inches Bulk) (Cut to 5.25 Inch Length) (To Lower Tee)	32-9912688
42	SCREW, (M6 x 16)	10-4009416
43	WASHER, (.255 x .620 x .030) Stainless Steel	12-69056
44	SOLENOID ASSEMBLY, Enrichner Valve	89-819503A1
45	TUBING, (38.00 Inches Bulk) (Cut to 15.00 Inch Length)	32-1430165
46	TUBING, (36.00 Inches Bulk) (Cut to 11.50 Inch Length) (To Upper Tee)	32-9912688
-	GASKET SET	27-13461A99
-	POWERHEAD ASSEMBLY	17791T97

Gasket Set Components(Engine Overhaul)

Below is the parts list for Mercury 125 (4 CYL.) Gasket Set Components(Engine Overhaul):

Position No.	Part Name	OEM Number	Supersedes
-	GASKET SET	27-13461A99
-	GASKET, Exhaust Plate to Cylinder Block	27-812775007
-	GASKET, Exhaust Baffle to Exhaust Cover	27-812775006
-	O-RING (2.862 I.D.)	25-89224
-	O-RING, (1.989 x .070) (1.989 I.D.)	25-823683	25-64067
-	GASKET, Cover Cylinder Block	27-443284
-	GASKET	27-8M0204714
-	GASKET, Cover, Thermostat	27-430068
-	NOT SOLD SEPARATE, Boost	NSS
-	NOT SOLD SEPARATE, Boost Chamber	NSS
-	NOT SOLD SEPARATE, Fuel Pump	NSS
-	NOT SOLD SEPARATE, Pluse Chamber	NSS
-	GASKET, Fuel Pump	27-8M0204705
-	GASKET, Reed Block/Crank	27-139376
-	O-RING (.739 I.D.)	25-8M0204667
-	O-RING (1.362 I.D.)	25-33466
-	GASKET, Exhaust Plate/Exhaust Tube	27-430086
-	SEAL, Water Tube	42941001
-	GROMMET	25-93221002
-	GASKET, Cylinder Block to Exhaust Plate	27-430075
-	O-RING, (1.424 x .103) (1.424 I.D.)	25-8M0204681
-	NOT SOLD SEPARATE, Seal	NSS
-	O-RING, (3.609 x .139) (3.609 I.D.)	25-8M0214974
-	GASKET, Aluminum Cover, Water Pump, Upper	27-430341
-	GASKET, Cover to Gearcase	27-8M0214931
-	GASKET, Water Pump, Upper	27-8172771
-	GASKET, Face Plate to Cover	27-430331
-	SEAL	12-191833
-	SEAL	19643
-	GASKET, Carburetor	27-151724
-	SPRING, Compression, Main	24-42998
-	NOT SOLD SEPARATE, Spring End	NSS
-	NOT SOLD SEPARATE, Spring End	NSS
-	NOT SOLD SEPARATE, Check Valve	NSS
-	RETAINER, Check Valve	21-17311
-	NOT SOLD SEPARATE, Compression, Boost	NSS
-	NOT SOLD SEPARATE, Spring End	NSS
-	GASKET, Manifold Cover	27-134612
-	GASKET, Use With 44324C1 And 44325C1, Exhaust Baffle Plate and Cover	27-139581
-	O-RING (2.112 I.D.)	25-858225

Gear Housing(Driveshaft)(2.07:1 Gear Ratio)

Below is the parts list for Mercury 125 (4 CYL.) Gear Housing(Driveshaft)(2.07:1 Gear Ratio):

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY (Long)	1667-9011J6
-	GEAR HOUSING ASSEMBLY (X-Long)	1667-9011J9
-	GEAR HOUSING ASSEMBLY Comment: (High Altitude-2.33:1)	1667-9011J15
1	GEAR HOUSING ASSEMBLY, Basic	1667-9011G59
2	PIN, Dowel - With Hole (.375 x .625) (Front)	17-8M0084244	17-43043
3	TUBE, Oiler	43046
4	SCREW KIT, (.375-16 x .250) Drain	10-79953Q04
4	PLUG KIT, Drain (Magnetic)	22-8M0058389	22-67892A06
5	SEAL	12-191833
6	PIN, Dowel - Without Hole (.375 x .625) (Rear)	17-43044
7	TRIM TAB	31640T07
8	SCREW, (.437-14 x 1.250) Stainless Steel	10-825427	10-15942
9	WASHER, (.453 x .812 x .105) Black Oxide	12-451761
10	CARRIER ASSEMBLY	43040T1
11	NOT SOLD SEPARATE, Needle Bearing	NSS
12	ANODE	97-826134Q	826134, 826134A 1
13	NUT, (M6) Stainless Steel	11-401386
14	SCREW, (M6 x 40)	10-4000333
15	NOT SOLD SEPARATE, Pinion Gear (14 Teeth) Comment: (Component of 43-881260A 3)	NSS
15	NOT SOLD SEPARATE, Pinion Gear (12 Teeth) Comment: (High Altitude-2.33:1)(Component of 43-882813A 3	NSS
16	NUT, (.625-18)	11-35921
17	CAM, Shift Control	850307
18	BEARING ASSEMBLY, Tapered Roller	31-883047A1
19	SHIM SET (006 Thru 048)	15-44492A1
20	DRIVESHAFT ASSEMBLY Comment: (Long-32 Inch)	45-43031A1
20	DRIVESHAFT ASSEMBLY Comment: (X-Long-37 Inch)	45-43032A4
21	SLEEVE/RING KIT	42461A1
22	NOT SOLD SEPARATE, Seal Ring	NSS
23	COVER ASSEMBLY, Water Pump	43055A4
24	GASKET	27-430331
25	GASKET	27-8M0214931
26	SEAL, Oil (Lower)	26-43036
27	SEAL, Oil (Upper)	26-43035
28	GASKET	27-8172771
29	HOUSING KIT, Upper Water Pump	817275A2
30	FACEPLATE	8M0204709
31	SCREW, (M6 x 30)	10-82684430
32	SEAL	430232
33	KEY	28-8M0204723
34	IMPELLER	47-43026T2
35	SCREW, (M6 x 25)	10-82684425
36	SHIFT SHAFT ASSEMBLY Comment: (Long-12 Inch)	853906A1
36	SHIFT SHAFT ASSEMBLY Comment: (X-Long-17 Inch)	853908A1
37	E RING	53-29641
38	BUSHING ASSEMBLY	23-43052A4
39	O-RING, (1.424 x .103)	25-8M0204681
40	SEAL, Oil	26-8M0204708
41	SCREW, (M6 x 25)	10-82684425
42	FACE SEAL	26-861415	26-816575
-	SEAL KIT, Gear Housing	26-43035A4
-	REPAIR KIT, Water Pump	46-8M0113799
-	GASKET SET	27-13461A99

Gear Housing, Propeller Shaft - 2.07:1 Gear Ratio

Below is the parts list for Mercury 125 (4 CYL.) Gear Housing, Propeller Shaft - 2.07:1 Gear Ratio:

Position No.	Part Name	OEM Number	Supersedes
-	GEAR HOUSING ASSEMBLY (Complete)(Long-20 Inch Model) Torpedo Diameter - 4.25 Inch / 107.95 mm Comment: NOTE: See Accessory Guide - Propeller Section- For Appropriate Hardware. (Thrust Washers/Nuts)	1667-9011J6
-	GEAR HOUSING ASSEMBLY (Complete)(X-Long-25 Inch Model) Torpedo Diameter - 4.25 Inch / 107.95 mm Comment: NOTE: See Accessory Guide - Propeller Section- For Appropriate Hardware. (Thrust Washers/Nuts)	1667-9011J9
-	GEAR HOUSING ASSEMBLY (Complete) Torpedo Diameter - 4.25 Inch / 107.95 mm Comment: (High Altitude-2.33:1 Ratio)	1667-9011J15
1	GEAR HOUSING ASSEMBLY, Basic	1667-9011G59
2	BEARING SET, Cup And Cone	31-30894A1
3	NOT SOLD SEPARATE, Cup	NSS
4	GEAR, Forward - 29 Teeth	43-881260A3
4	GEAR KIT, Forward And Pinion 28 Teeth Comment: (High Altitude-2.33:1 Ratio)	43-882813A3
5	BEARING, Needle	31-30895T
6	RING, Retaining	53-856823
7	FOLLOWER KIT, Cam	850315A1
8	BALL	30-44530
9	NOT SOLD SEPARATE, Slide	NSS
10	SPRING	24-850327
11	PIN, Cross	17-8M0100263	17-8M0084681, 17-8M0020941, 17-30632
12	SPRING	24-30893
13	CLUTCH	52-850048T	52-850048
14	PROPELLER SHAFT	44-8M0140445
15	GEAR, Reverse - 29 Teeth	43-850036T	43-850036
15	GEAR, Reverse - 28 Teeth Comment: (High Altitude-2.33:1 Ratio)	43-882814T
16	CARRIER ASSEMBLY, Bearing	8M0168901
17	O-RING, (3.609 x .139)	25-8M0214974
18	BEARING, Needle	31-30956T
19	SEAL, Oil (Inner)	26-8M0205728
20	SEAL, Oil (Outer)	26-8M0205729
21	BEARING, Roller	31-12578T
22	THRUST WASHER	12-12577
23	BEARING, Thrust	31-12576
24	STUD, (M8 x 48)	16-8M0034456	16-42917 2
25	WASHER, (.323 x .590 x .112) Stainless Steel	12-855941
26	NUT, (M8)	11-401378
27	SHIM SET (006 Thru 038)	15-44491A1
28	INSERT, Threaded	8227731
29	NOT SOLD SEPARATE, Decal-G/H Pinion Indent	NSS
-	COVER ASSEMBLY, Water Pump	43055A4
-	GASKET SET	27-13461A99

Induction Manifold and Reed Block

Below is the parts list for Mercury 125 (4 CYL.) Induction Manifold and Reed Block:

Position No.	Part Name	OEM Number	Supersedes
1	COVER/PLATE KIT, Exhaust	44325A1
2	NOT SOLD SEPARATE, Exhaust Plate	NSS
3	GASKET, Baffle Plate to Cylinder Block	27-812775007
4	GASKET, Exhaust Baffle to Exhaust Cover	27-812775006
5	SCREW, (M8 x 35 MM)	10-82127335
6	FITTING, Elbow 90 Degree (.125-27 x .250) Nylon	22-996642
7	SHIFT RAIL ASSEMBLY	42881A1
8	TAB WASHER	14-42981
9	SCREW, (M8 x 25)	10-40001134
10	SLIDE	988851
11	NUT, (M6) Stainless Steel	11-401386
12	WASHER	12-35459
13	NUT, (M6) Stainless Steel	11-401386
14	GASKET	27-430075
15	CAP ASSEMBLY, Lower End	1169-858552T2
16	CHECK VALVE	21-426585
17	SEAL, Oil	26-419533
18	O-RING	25-89224
19	SCREW, (M10 x 25) Hex Flange - Stainless Steel	10-4010825
20	TEE FITTING	22-13033
21	TUBING, (38.00 Inches Bulk) (Cut to 5.50 Inch Length)	32-1430165
22	FITTING (Straight)	22-130351
23	MANIFOLD ASSEMBLY, Induction	13545A1
24	BRACKET	827514
25	SCREW, (M8 x 35 MM)	10-82127335
26	SCREW, (M8 x 40)	10-81742740
27	STUD, (M6 x 44)	16-8161949
28	WASHER, (.187 x .500 x .062) Neoprene	12-8M0204663
29	WING NUT	11-816872
30	SCREW, (M8 x 110) (#4 Cylinder)	10-40001167
31	STUD, (M8 x 1.25) (#1, 2, 3 Cylinder)	16-824470	16-42985, 16-42985 1
32	GASKET	27-134612
33	COVER	13460
34	SCREW, (M8 x 55)	10-81742755
35	REED BLOCK ASSEMBLY	8M0219198
36	NOT SOLD SEPARATE, Dowel Pin	NSS
37	GASKET	27-139376
38	REED SET	34-43018A1
39	TAB WASHER	14-429821
40	RETAINER	42924
41	SCREW, (M6 x 16)	10-88421471
42	DECAL, EPA Label Information (2006)	37-804667A06
42	DECAL, EPA Label Information (2005)	37-804667A05
-	GASKET SET	27-13461A99
-	POWERHEAD ASSEMBLY	17791T97

Jet Pump Assembly

Below is the parts list for Mercury 125 (4 CYL.) Jet Pump Assembly:

Position No.	Part Name	OEM Number	Supersedes
-	JET PUMP ASSEMBLY	856143A1
1	HOUSING, Pump	855767T90	855767 90
2	SHIFT LINKAGE KIT	878377
3	CAM	878382
4	GATE, Reverse - With Bumper	878380
5	HOSE, Lube	32-827490
6	SCREW, (.312-18 x 1.00)	10-848497
7	STUD, (.312-18 x 1.81)	16-855840
8	NUT, (.312-18) Stainless Steel	11-82670910
9	HOUSING, Intake	85576890
10	LINER	855771
11	DRIVESHAFT	45-85576990
12	THRUST WASHER	12-8796522
13	BEARING, Ball	30-8796531
14	SLEEVE	23-8271891
15	NUT	11-8271901
16	ADAPTOR, Pump	808747
17	IMPELLER	47-855708115	47-801414 90, 47-801414115
18	WASHER	12-36001
19	KEY	28-801405875
20	SHIM, Impeller	15-801404875
21	TAB WASHER	14-801403875
22	PIN, Dowel	17-801407
23	SCREW, (.250-20 x .625)	10-19923062
24	SCREW, (.312-18 x 1.250)	10-60411
25	BRACKET, Cable Support	801410
26	NUT, (.312-18) Stainless Steel	11-82670910
27	SCREW, (M10 x 60) Hex Flange - Stainless Steel	10-4010860
28	SCREW, (M10 x 90) Hex Flange - Stainless Steel	10-4010890
29	SCREW, (M10 x 70) Hex Flange - Stainless Steel	10-4010870
30	SCREW, (.375-16 x 4.00) Stainless Steel	10-843575
31	WASHER, (.406 x .750 x .105) Stainless Steel	12-8M0214963

Jet Pump Components

Below is the parts list for Mercury 125 (4 CYL.) Jet Pump Components:

Position No.	Part Name	OEM Number
1	HOUSING KIT, Upper Water Pump Comment: (Lubricate/Sealant Application Points)	817275A2
2	GASKET	27-8172771
3	FACEPLATE	8M0204709
4	SCREW, (M6 x 30)	10-82684430
5	SEAL	430232
6	KEY	28-8M0204723
7	IMPELLER	47-43026T2
-	SEAL KIT, Gear Housing	26-43035A4
-	REPAIR KIT, Water Pump	46-8M0113799
-	GASKET SET	27-13461A99

Key Chart

Below is the parts list for Mercury 125 (4 CYL.) Key Chart:

Position No.	Part Name	OEM Number
-	KEY, Ignition (1A)	894911
-	KEY, Ignition (1B)	894912
-	KEY, Ignition (1C)	894913
-	KEY, Ignition (1D)	894914
-	KEY, Ignition (1E)	894915
-	KEY, Ignition (1F)	894916
-	KEY, Ignition (2A)	894917
-	KEY, Ignition (2B)	894918
-	KEY, Ignition (2C)	894919
-	KEY, Ignition (2D)	8949110
-	KEY, Ignition (2E)	8949111
-	KEY, Ignition (2F)	8949112

Lube Chart

Below is the parts list for Mercury 125 (4 CYL.) Lube Chart:

Position No.	Part Name	OEM Number	Supersedes
	NO PARTS LIST	NOPART

Oil Injection Components

Below is the parts list for Mercury 125 (4 CYL.) Oil Injection Components:

Position No.	Part Name	OEM Number	Supersedes
1	TANK ASSEMBLY, Oil	1278-8M0219217
1	TANK ASSEMBLY, Oil	1278-8M0219217
2	CAP	828475A1
3	O-RING	25-26318T
4	DIPSTICK	828793
5	NUT	11-65110
6	VENT ASSEMBLY	19299A1
7	VALVE	21-64871
8	BRACKET	8287201
9	BOOT	99160001
10	SCREW, (M6 x 20) Stainless Steel	10-4010620
11	GROMMET	25-825380001	25-825380
12	BUSHING	23-828350
13	WASHER	12-4002318
14	SCREW, (M8 x 35)	10-81893435
15	SWITCH ASSEMBLY	87-12886A6
16	SCREW, (.164-18 x .375)	10-58376
17	WASHER, (.203 x .562 x .060) Stainless Steel	12-72761
18	GEAR, Driven	43-430204
19	O-RING	25-8M0204667
20	ADAPTOR ASSEMBLY	17335A3
21	BUSHING	23-17597
22	BUSHING	23-17596
23	PUMP, Oil	44345T3
24	SCREW, (M5 x 40)	10-82104540
25	TUBING, (15.00 Inches Bulk) (Cut to 6.00 Inch Length)	32-82381335
26	TUBING, (25.00 Inches Bulk) (Cut to 11.00 Inch Length)	32-82381455
27	TIE STRAP, (5.50 Inches)	8M0214940
27	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
-	GASKET SET	27-13461A99

Power Trim Components

Below is the parts list for Mercury 125 (4 CYL.) Power Trim Components:

Position No.	Part Name	OEM Number	Supersedes
-	PUMP ASSEMBLY, Power Trim	8M0171818
-	PUMP ASSEMBLY, Power Trim	8M0171818
1	SHOCK ROD KIT	8M0171821
2	O-RING KIT, Rebuild	25-8M0171819
3	PISTON ASSEMBLY, Memory	8M0171822
4	CYLINDER ASSEMBLY	893916A01	811669A 1
5	VALVE KIT, Trim Limit	893905A02	809873A 1
6	PUMP ASSEMBLY	893906A02	809874A 1
7	MOTOR KIT	893907A02	809885A 2
8	PLUG	22-8134351
9	MANUAL RELEASE ASSEMBLY	893929A01	813442A 2
10	MANIFOLD KIT	893909A02	809875A 1
11	SCREW KIT (Motor)	10-809876A1
12	CABLE ASSEMBLY	88238A18
13	DRIVESHAFT/SEAL KIT	809877A1
14	FILTER KIT	35-893912A02	809878A 1
15	POPPET KIT	893913A02	809879A 1
-	O-RING KIT (Complete Trim)	25-893914A02	25-809880A 1
16	RELAY ASSEMBLY	8M0207773
17	BUSHING	23-8M0214955
18	GROMMET	25-818967
19	BRACKET	828102
20	NOT SOLD SEPARATE, Decal-Trim Relay	NSS
21	HARNESS ASSEMBLY, Trim	84-8M0092077
22	SCREW, (M6 x 25 MM)	10-82129125
23	CLIP	54-22740
24	SCREW, (#10-16 x .600)	10-878609	10-812832 1
25	C WASHER	8M0084613	69205

Service/Support Material

Below is the parts list for Mercury 125 (4 CYL.) Service/Support Material:

Position No.	Part Name	OEM Number	Supersedes
-	PARTS MANUAL, 115/125 Hp 80 Jet (4 Cylinder)	90-803168001
-	SERVICE MANUAL	90-8M0127990
-	OWNERS MANUAL, (2005) Comment: English	90-10180050
-	OWNERS MANUAL, (2005) Comment: (2005) French	90-10180D50
-	OWNERS MANUAL, (2005) Comment: (2005) Spanish	90-10180J50
-	OWNERS MANUAL, (75/90/115/125)(2-Stroke) Comment: (2006) English	90-10180080
-	OWNERS MANUAL, (75/90/115/125)(2-Stroke) Comment: (2006) French	90-10180D60
-	OWNERS MANUAL, (75/90/115/125)(2-Stroke) Comment: (2006) Spanish	90-10180J60
-	OWNERS MANUAL, Jet 65/80 (2005)	90-10138050
-	HOSE ASSEMBLY, Fuel	32-858610A31	32-858610A10, 32-16789A18
-	DECAL SET, (Black 80 Jet) (2005)	37-826321A00	37-826321A96, 37-826321A95
-	DECAL SET, (Black 115 - Red) (2005)	37-823407A00	37-823407A96, 37-823407A94
-	DECAL SET, (Black 125 - Red) (2005)	37-823410A00	37-823410A96, 37-823410A94
-	DECAL SET, (Black 115 - Blue) (2005)	37-803165A00	37-803164A99, 37-803165A99
-	DECAL SET, (Black 125 - Blue) (2005)	37-803166A00	37-803166A99
-	DECAL SET, (Gray 115) (2005 and Up)	37-823412A03	37-823412A01, 37-803167A99, 37-823412A97, 37-823412A94, 37-850445A97, 37-803167A00
-	DECAL SET, (Gray 125) (2005 and Up)	37-823413A03	37-823413A01, 37-823413A97, 37-823413A94, 37-850446A97
-	DECAL SET (Tracker 115) Comment: (2005)	37-824735A96
-	DECAL SET (Tracker 125) Comment: (2005)	37-808623A96
-	DECAL SET, (Black 115) (2006 and Up)	37-897515A01
-	DECAL SET, (Black 125) (2006 and Up)	37-897515A02
-	DECAL, EPA Label Information (2005)	37-804667A05
-	DECAL, EPA Label Information (2006)	37-804667A06

Starter Motor

Below is the parts list for Mercury 125 (4 CYL.) Starter Motor:

Position No.	Part Name	OEM Number	Supersedes
-	STARTER MOTOR ASSEMBLY	50-893892T	50-66015 3
1	DRIVE KIT	15383
2	PINION ASSEMBLY	13310T1
3	PLATE	75660
4	THRU BOLT	15384
5	ARMATURE	15385
6	BRUSH/SPRING KIT	898265016	75384, 75384 1
7	END CAP	15386001

Steering Handle

Below is the parts list for Mercury 125 (4 CYL.) Steering Handle:

Position No.	Part Name	OEM Number	Supersedes
1	HANDLE ASSEMBLY, Steering Arm	12020A3
NS	FITTING, Grease	22-8M0169589
2	BUSHING	23-42992T02
3	HOUSING	48414
4	PLATE	48519
5	GASKET	27-48518
6	SCREW, (#10-16 x .600)	10-878609	10-812832 1
7	SCREW, (#10-16 x .500)	10-878608	10-812832
8	CLAMP	54-889729	54-12013
9	SCREW, (M5 x 40)	10-40007112
10	WING NUT,	10-32,11-816874	11-73651, 11-816873, 11-90052
11	HANDLE, Throttle (#96495 6)
12	SWITCH KIT, Stop - Throttle Handle	87-823609A15	87-15823A 6, 96495A 3, 87-15823A 5
13	SWITCH ASSEMBLY, Stop	87-8M0104612	87-823609A 5
14	TUBE ASSEMBLY, Throttle	12018A4
15	NOT SOLD SEPARATE, Drive Wheel	NSS
16	NOT SOLD SEPARATE, Roll Pin	NSS
17	SCREW, (#10-16 x .375)	10-62568
18	GRIP	8M0221732
19	CLAMP	54-648551
20	NUT, (M10)	11-40140
21	CONDUIT	8885242
22	GUIDE TUBE	895663
23	BARREL	89578
24	SET SCREW,	10-32,10-824081	10-89601
25	CABLE ASSEMBLY	120191
26	GUIDE	434332
27	ANCHOR	20007
28	SET SCREW,	8-32,10-8M0204644
29	SCREW, (M10 x 105) Hex Flange - Stainless Steel	10-823567105	10-817430105
30	CAP	48416
31	WASHER	12-4002319
32	WASHER, (.402 x .787 x .039 Bellevi)	12-12024
33	SPACER	23-146011
34	WASHER, (.406 x .750 x .105) Stainless Steel (Use Where Applicable)	12-8M0214963
35	TIE STRAP, (8.00 Inches)	54-816311T	54-816311, 54-90077, 54-826785, F1877, F717046-1, F717046, MAF03001, 833188E, 54-F9301, 54-816311100, 54-898101111, 54-898101275
36	NOT SOLD SEPARATE, Decal-Throttle	NSS
-	TILLER HANDLE KIT	12022A41

Steering Handle Components

Below is the parts list for Mercury 125 (4 CYL.) Steering Handle Components:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET ASSEMBLY	12022A22
2	SCREW, (.375-24 x 1.250)	10-849838	10-14000
3	NUT, (.375-24) Stainless Steel	11-8M0204726
4	STUD, (.3125 x 2.50)	16-8M0034421	16-822320
5	SPACER	822263
6	WASHER, (.344 x .688 x .065) Stainless Steel	12-8M0204690
7	NUT, (.312-24) Stainless Steel	11-82670911
8	GROMMET	121051
9	HARNESS ASSEMBLY	84-12649A5
10	SWITCH KIT, Key Comment: (See Key Chart for Keys)	87-88107A5
11	NUT, Special - Black Nylon Comment: (Black Nylon)	11-879755	11-93543 (Black Nylon)
12	COVER	12015A1
13	SCREW, (#10-16 x .500)	10-878608	10-812832
14	SWITCH ASSEMBLY, Stop	87-11083A4
15	LANYARD ASSEMBLY	15920Q54
16	RETAINER, Brass	8M0032846	12044 1
17	SCREW, (M8 x 50)	10-4000358
18	TAB WASHER	14-42981
19	BUSHING	23-889732	23-42992 1
20	LEVER ASSEMBLY, Shift	12021A1
21	WASHER	12-815351
22	NOT SOLD SEPARATE, Decal-Shift	NSS
23	STUD, (.375-24 x 1.125)	16-8M0034452	16-58152
24	KNOB	98530
25	SHIFT ROD	495636
26	ROD END	48419T
27	BUSHING	23-26856
28	WASHER, (.273 x .437 x .031) Stainless Steel	12-35950
29	COTTER PIN	18-25191
30	DETENT/SPRING KIT	12016A2
31	NOT SOLD SEPARATE, Spring	NSS
32	TRIM SWITCH (Power Trim)	87-14645A4
33	NUT, (.468-32) (Power Trim)	49440
34	NOT SOLD SEPARATE, Decal-Trim Comment: (Component of 14645A 4 Trim Switch)	NSS
35	HORN ASSEMBLY	816051A2
36	CABLE ASSEMBLY	84-11149A3
37	CABLE ASSEMBLY	84-86324A2
38	BRACKET Comment: (X-Long)	824930T3
39	SWITCH Comment: (X-Long)	87-8M0052927	87-813960A 3 (X-Long)
40	SCREW, (M3 x 20) Comment: (X-Long)	10-88075020
41	PLATE Comment: (X-Long)	824923
42	HARNESS ASSEMBLY Comment: (X-Long)	84-824934A3
-	TILLER HANDLE KIT	12022A41

Swivel Bracket and Steering Arm

Below is the parts list for Mercury 125 (4 CYL.) Swivel Bracket and Steering Arm:

Position No.	Part Name	OEM Number	Supersedes
1	SWIVEL BRACKET	1400-8M0220957
2	SEAL, Oil, Lower	26-87735
3	BUSHING	23-818764	23-67669
4	O-RING	25-8M0214926
5	SPACER	23-816039
6	FITTING, Grease	22-8M0169589
7	BUSHING	23-821207	23-99608
8	SCREW, (.250-28 x .500)	10-64014
9	THRUST WASHER	12-816432
10	SWIVEL PIN ASSEMBLY	99661A35
11	LINK ROD ASSEMBLY	92876A12
12	SCREW, (.375-24 x 1.250)	10-849838	10-14000
13	NUT, (.375-24) Stainless Steel	11-8M0204726
14	WASHER, (.390 x .625 x .062) Stainless Steel	12-37828
15	NUT, (.375-24) Stainless Steel	11-8M0204726
16	BUMPER	8M0000519	881974
17	YOKE, Bottom	881914T01
18	RING, Retaining	53-67684
19	BUMPER, Bottom Yoke Comment: (X-Long)	11288001

Throttle Lever and Linkage

Below is the parts list for Mercury 125 (4 CYL.) Throttle Lever and Linkage:

Position No.	Part Name	OEM Number	Supersedes
1	LEVER, Throttle	884309T	884309, 44333
2	SCREW, (M5 x 40)	10-827009
3	CAP	826264
4	SPRING	24-826382
5	CAP	48039
6	LEVER, Spark Advance	884307T	884307, 44335
7	SCREW, Adjusting (M6 x 55)	10-814776	10-42978
8	NUT, (M6) Stainless Steel	11-400212
9	CAP	42942
10	SCREW, (M10 x 45)	10-4007180
11	BUSHING	23-55171
12	SPRING	24-73375
13	BUSHING	23-812930A1
14	NOT SOLD SEPARATE, Insert	NSS
15	WASHER	12-42980
16	INSERT	42927
17	WASHER	12-35459
18	NUT, (M6) Stainless Steel	11-401386
19	ROD, Spark Advance	878170	44338
20	SWIVEL BALL	93421
21	SWIVEL BASE	93254
22	BUSHING	23-8M0215006
23	NUT, (M6) Stainless Steel	11-401386
24	WASHER, (.255 x .620 x .030) Stainless Steel	12-69056
25	LINK	878173	44337
26	BUSHING	23-8M0215006
27	CAM ASSEMBLY, Throttle	14518A2
28	STUD, (M6 x 44)	16-8161949
29	NOT SOLD SEPARATE, Decal-Idle Screw (Arrow-Down)	NSS

Tiller Handle Adapter Kit(Jet 80)

Below is the parts list for Mercury 125 (4 CYL.) Tiller Handle Adapter Kit(Jet 80):

Position No.	Part Name	OEM Number	Supersedes
-	TILLER HANDLE ADAPTOR KIT	850000A3
1	CABLE ASSEMBLY, Shift	832001A6
2	NUT, (M6) Stainless Steel	11-401386
3	SLIDE	988851
4	BRACKET	828095
5	BRACKET	824930T3
6	CLIP	54-8054441
7	SCREW, (M6 x 13) Stainless Steel	10-40011126
8	BLOCK, Shift Cable-Retaining	828096
9	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
10	SCREW, (.250-28 x 1.75)	10-71958
11	LOCKWASHER, (.250) Stainless Steel	13-26992
12	BLOCK, Shift Cable-Retaining	828094
13	SET SCREW, (#10-32 x .310)	10-72734
14	WASHER	12-35459
15	NUT, (.250-28) Stainless Steel	11-35888
16	SWITCH	87-8M0052927	87-813960A 3
17	SCREW, (M3 x 20)	10-88075020
18	PLATE	824923
19	CABLE ASSEMBLY	84-824934A1

Tools(Special)

Below is the parts list for Mercury 125 (4 CYL.) Tools(Special):

Position No.	Part Name	OEM Number	Supersedes
-	PULLER ASSEMBLY	91-849154T1
-	FLYWHEEL HOLDER TOOL, Teeth Type	91-52344
-	TORQUE WRENCH, (0-150 lb-in)	91-66274
-	MULTI METER	91-99750A1
-	SWITCH ASSEMBLY Comment: (Electrical/Ignition)	91-52024A1
-	SERVICE TACHOMETER Comment: (Electrical/Ignition)	91-59339
-	TESTER, Eight Chamber Comment: (Electrical/Ignition)	91-850439T1
-	GAP TOOL, Single Chamber Comment: (Electrical/Ignition)	91-63998A1
-	TESTER, Eight Chamber Comment: (Electrical/Ignition)	91-850439T1
-	TIMING LIGHT Comment: (ELECTRICAL/IGNITION)	91-99379
-	HARNESS ASSEMBLY Comment: (Electrical/Ignition)	84-825207A2
-	ALIGNMENT TOOL Comment: (Trim/Tilt System)	91-112301
-	NOT SOLD SEPARATE (SNAP ON - CG41-14) Comment: (Trim/Tilt System)	NSS
-	NOT SOLD SEPARATE (SNAP ON - CG41-11) Comment: (Trim/Tilt System)	NSS
-	DOWN PRESSURE KIT Comment: (Trim/Tilt System)	91-822778A3
-	SPANNER WRENCH Comment: (Trim/Tilt System)	91-74951
-	HEAT LAMP Comment: (Trim/Tilt System)	91-63209
-	GAUGE TOOL Comment: (Powerhead)	91-29287
-	LIFTING EYE Comment: (Powerhead)	91-904551
-	INSTALLER KIT Comment: (Powerhead)	91-77109A3
-	INSTALLER KIT, Piston Pin Comment: (Powerhead)	91-74607A3
-	EXPANDER TOOL, Piston Ring Comment: (Powerhead)	91-24697
-	STAND, Powerhead Comment: (Powerhead)	91-812549T	91-812549 (Powerhead)
-	CAP TOOL, Flywheel Puller Comment: (Powerhead)	91-24161
-	INDICATOR TOOL, Backlash Comment: (Gear Housing)	91-8M0053505	91-78473 (Gear Housing)
-	INDICATOR TOOL, Backlash Comment: (Gear Housing)	91-196601
-	MANDREL, Bearing Driver Cup Comment: (Gear Housing)	91-31106T
-	INSTALLATION TOOL, Bearing Comment: (Gear Housing)	91-13945
-	INSTALLATION TOOL, Bearing Comment: (Gear Housing)	91-14309T02
-	TOOL, Preload Comment: (Gear Housing)	91-14311A04
-	PULLER ASSEMBLY Comment: (Gear Housing)	91-83165T
-	TOOL KIT, Bearing Race Comment: (Gear Housing)	91-14308T02
-	PULLER KIT, Bearing Comment: (Gear Housing)	91-31229A7
-	NUT, (.625-18) Comment: (Gear Housing)	11-24156
-	MANDREL Comment: (Gear Housing)	91-15755T
-	DRIVE HEAD TOOL Comment: (Gear Housing)	91-36569T
-	DRIVER ROD TOOL, Needle Bearings Comment: (Gear Housing)	91-37323
-	MANDREL Comment: (Gear Housing)	91-37350T
-	RETAINING TOOL, Bearing Comment: (Gear Housing)	91-43506T
-	ADAPTER KIT, Dial Indicator Comment: (Gear Housing)	91-83155
-	DIAL INDICATOR TOOL Comment: (Gear Housing)	91-58222A1
-	HOLDING TOOL, Driveshaft Comment: (Gear Housing)	91-56775T
-	INSTALLER TOOL, Bearing Comment: (Gear Housing)	91-826872
-	DRIVER TOOL, Oil Seal Comment: (Gear Housing)	91-13949
-	DRIVER, Oil Seal Comment: (Gear Housing)	91-31108T
-	LOCATION TOOL, Pinion Comment: (Gear Housing)	91-12349A05
-	PULLER JAW ASSEMBLY Comment: (Gear Housing)	91-46086A1
-	PULLER PLATE, Universal Comment: (Gear Housing)	91-37241
-	PULLER ASSEMBLY, Slide Hammer Comment: (Gear Housing)	91-34569A1
-	BEARING, Thrust Comment: (Gear Housing)	31-85560
-	WEAR SLEEVE INSTALLATION TOOL Comment: (Gear Housing)	91-14310T1

Top Cowl

Below is the parts list for Mercury 125 (4 CYL.) Top Cowl:

Position No.	Part Name	OEM Number	Supersedes
1	TOP COWL ASSEMBLY, Black	4026-828354T8
1	TOP COWL ASSEMBLY, Silver	4026-828354T9
1	TOP COWL ASSEMBLY, Silver Cowl And Black Cap Comment: (Tracker)	4026-828354A10
2	CAP	828716A2
3	SEAL	828352
4	SEAL	8283511
5	CAP, Upper Comment: (Black)	8218751
5	CAP, Upper Comment: (Silver)	821875F2
6	BRACKET, Cover Latch	819813T1
7	BRACKET ASSEMBLY, Latch Roller	893763	18173
8	LOCKWASHER, (.312)	13-53166
9	SCREW, (.312-18 x .625)	10-90285
10	GUIDE, Cowl Latch Bracket	F481434
11	PUSH NUT	11-91925
12	SCREW, (.250-20 x 1.00)	10-822512
13	CAP PLUG	19-823865
14	SCREW, (M6 x 16)	10-82130016
15	SUPPORT	823830
16	SCREW, (M4 x 14.5)	10-8231871
17	LOCKWASHER, Stainless Steel	8,13-26995
18	BRACKET	8233941
19	NUT, (M4)	11-8237515
20	SOUND BLANKET KIT Comment: (Hot Glue Adhesive)	823583A02	823583A 1 (Hot Glue Adhesive)
20	SOUND BLANKET KIT, (Pre-Applied Pressure Sensitive Adhesive)	823583A02	823583A 1
21	NOT SOLD SEPARATE, Sound Blanket	NSS
22	ROPE AND HANDLE KIT, Manual Starting	47341A11

Transom Bracket

Below is the parts list for Mercury 125 (4 CYL.) Transom Bracket:

Position No.	Part Name	OEM Number	Supersedes
1	BRACKET, Transom (Starboard)	3426-828334T02	3426-828334F 1
2	BRACKET ASSEMBLY, Transom (Port)	3425-828333T07	3425-828333A 3
3	FITTING, Grease (Port)	22-8M0169588
4	TUBE KIT, Tilt Comment: (Carbon Steel)	99170A2
4	TILT TUBE (Stainless Steel)(Saltwater)	826125A1
5	NUT, (1.00-14)	11-859133	11-34862, 11-90068F 3, 11-90068F 4
5	NUT, (1.00-14) Nylon Insert (Stainless Steel)(Saltwater)	11-826135
6	O-RING, (.612 x .103)	25-45711
7	WASHER	13-88750
8	NUT, (.875-14)	11-858869	11-30499
8	NUT, (.875-14) (Brass)(Saltwater)	11-826164
9	SCREW, (.500-20 x 4.500)	10-8M0149747
10	WASHER, (.530 x .870 x .105) Stainless Steel	12-8M0204665
11	WASHER, (1.5 x 3.05 x 0.13) Stainless Steel	12-8M0204648
12	NUT, (.500-20)	11-82671117
13	SPRING, Tension	24-830899
14	LEVER ASSEMBLY, Tilt Lock	8M0109798	821176T02, 821176T 1
15	NYLINER	23-65830
16	SPRING, Compression	24-830900
17	KNOB	99633
18	PIN, Groove	17-99615
19	PIN	17-893709	17-99617
20	BRACKET, Anchor	8M0086406	818771T 1
21	SCREW, (M10 x 30)	10-858771
22	WASHER	12-4002319
23	NUT, (M10 x 1.5)	11-40114
24	ANODE	97-818298Q1
25	SCREW, (M6 x 25)	10-8M0204707
26	WASHER, (.281 x .500 x .060) Stainless Steel	12-8M0204649
27	CLIP	54-22740
28	C WASHER	8M0084613	69205
29	SCREW, (#10-16 x .600)	10-878609	10-812832 1
30	PUMP ASSEMBLY, Power Trim Comment: (See Power Trim Components section for parts breakdown)	8M0171818
31	SHAFT (Upper)	99625002
32	PIN, Anchor	17-818898
33	PIN, Trilobe	17-821539	17-13794, 17-19603

Download this page as PDF: Click here

For Mercury Owners:

To assist you in maintaining and repairing your marine engines, we hope the following resources may be of use:

Mercury / Mercruiser / Mariner Parts from JLM Marine

About JLM Marine

Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.

As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.

We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.