🔎 Mercury 350 PRO VERADO (4-Stroke)(6 CYL.) Reference Library — Exploded parts diagrams (42 diagrams), specifications, common issues, and maintenance checklist.
The Mercury 350 PRO VERADO (4-Stroke)(6 CYL.) is a 4-Stroke, V10 64-degree, Naturally Aspirated outboard motor. Designed for large center-consoles, offshore sport-fishing boats, and multi-engine configurations.
Quick Reference Specifications
| Specification |
Value |
| Engine Type |
4-Stroke, V10 64-degree, Naturally Aspirated |
| Horsepower |
350 HP |
| Displacement |
5700 cc (5.7L / 349 CID) |
| Bore x Stroke |
92 mm x 86 mm (3.6 in. x 3.4 in.) |
| Spark Plug (Type & Gap) |
NGK ILFR6G-E |
| Engine Oil Capacity |
7.0 L (7.4 US qt) with filter |
| Recommended Engine Oil |
Mercury SAE 25W-40 Marine Engine Oil |
| Gear Case Oil Capacity |
970 mL (32.8 oz) |
| Idle Speed (in gear) |
650–700 RPM (in gear) |
| Full Throttle RPM Range |
5800-6400 |
| Fuel |
Unleaded Gasoline, 87 Octane min. |
Always verify specifications against your owner's manual for your specific serial number range.
Common Issues & Recommended Parts
Below are common maintenance scenarios for the Mercury 350 PRO VERADO (4-Stroke)(6 CYL.):
-
Water Pump / Overheating: If the tell-tale stream is weak or absent, the water pump impeller likely needs replacement. Inspect annually or every 100 hours. → Recommended: Water Pump Impeller Kit
-
Engine Oil / Maintenance Light: 4-stroke engines require regular oil and filter changes. Use marine-grade oil rated for your engine. Change every 100 hours or annually. → Recommended: Oil Filter, Engine Oil
-
Fuel Injector Issues (EFI models): Rough idle or misfires may indicate clogged fuel injectors. Use fuel stabilizer and clean injectors periodically. → Recommended: Fuel Injector, Fuel Filter
-
Gear Case Oil Leak: Check lower unit seals if gear oil appears milky (water contamination). Replace seals and gaskets during lower unit service. → Recommended: Lower Unit Seal Kit, Drain Plug Gaskets
-
Anode Corrosion: Inspect sacrificial anodes regularly, especially in saltwater. Replace when 50% depleted to protect against galvanic corrosion. → Recommended: Zinc/Aluminum Anode Kit
Parts Diagrams & OEM Part Numbers
Expand the sections below to view detailed exploded parts diagrams and find the exact OEM replacement components for your Mercury 350 PRO VERADO (4-Stroke)(6 CYL.).
▶Accessories (1 parts)
| Ref |
OEM Part # |
Part Name |
| - |
8M0079968 |
PUMP DRAIN KIT, Upgrade kit |
▶Adaptor Plate Hose Routings (30 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-896966A06 |
LONG BLOCK ASSEMBLY |
| 1 |
17-884474001 |
PIN, Dowel (12 mm) |
| 2 |
888819002 |
DRAIN, Cowl |
| 3 |
22-888461A01 |
FITTING KIT |
| 4 |
25-892446 |
O-RING, (14 X 1.78 MM) |
| 5 |
10-8M0103804 |
SCREW, (M6 x 12 MM) Stainless Steel |
| 6 |
12-8M0214930 |
WASHER |
| 7 |
22-889792A01 |
FITTING KIT, Idle Exhaust |
| 8 |
25-889828 |
O-RING, (.924 x .103) |
| 9 |
22-889846 |
FITTING |
| 10 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 11 |
32-888981001 |
HOSE, Idle Exhaust |
| 12 |
892384T |
PLENUM, Exhaust |
| 13 |
10-4006731 |
SCREW, (M6 x 16) |
| 14 |
88238A21 |
CABLE ASSEMBLY |
| 15 |
10-40011126 |
SCREW, (M6 x 13) Stainless Steel |
| 16 |
32-8M0203773 |
HOSE, Manifold Reference , Lower |
| 17 |
25-884546 |
GROMMET |
| 18 |
888523001 |
CLIP |
| 19 |
32-8M0129144 |
HOSE, Water In, Lower |
| 20 |
32-8M0084660 |
HOSE, Fuel Out, Fuel Supply Module |
| 21 |
54-815504104 |
CLAMP, Worm Gear |
| 22 |
32-8M0108349 |
TUBING, (.312) (70 Inches Bulk), Cut to 21 Inches |
| 23 |
892562T01 |
HOUSING, Manifold |
| 24 |
892117 |
SEAL |
| 25 |
10-8M0103805 |
SCREW, (M6 x 16 MM) Stainless Steel |
| 26 |
32-887756 |
HOSE, Water In-Upper |
| 27 |
32-8M0203762 |
HOSE, Hi Pressure Filter |
| 28 |
35-879885Q |
FILTER, Fuel In-Line |
| 29 |
32-8M0203763 |
HOSE, Hi Pressure Filter to Fuel Rail |
▶Adaptor Plate-Lower (30 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-896966A06 |
LONG BLOCK ASSEMBLY |
| 1 |
887623T03 |
PICKUP ASSEMBLY, Oil |
| 2 |
25-8M0092943 |
O-RING |
| 3 |
10-8M0103807 |
SCREW, (M6 x 25 MM) Stainless Steel |
| 4 |
27-889618001 |
GASKET, Oil Sump |
| 5 |
8M0080961 |
TUBE ASSEMBLY, Exhaust |
| 6 |
10-8M0103814 |
SCREW, (M8 x 35 MM) |
| 7 |
26-880629 |
SEAL, Exhaust Tube |
| 8 |
880639T |
SUMP ASSEMBLY, Oil |
| 9 |
10-8M0103808 |
SCREW, (M6 x 30 MM) Stainless Steel |
| 10 |
8M0082193 |
TUBE ASSEMBLY, Oil Drain Comment: (X-Long/XX-Long) |
| 11 |
25-892446 |
O-RING, (14 X 1.78 MM) |
| 12 |
17-892228 |
PIN, Dowel |
| 13 |
888592005 |
PLUG ASSEMBLY, Oil Drain |
| 14 |
26-888593 |
SEAL, Drain Plug |
| 15 |
10-8M0103808 |
SCREW, (M6 x 30 MM) Stainless Steel |
| 16 |
32-885541A03 |
TUBE ASSEMBLY, Water (30.00 Inch) Comment: (XX-Long) |
| 17 |
25-892445 |
O-RING |
| 18 |
22-8M0214983 |
COUPLING |
| 19 |
25-8M0204673 |
O-RING, (.921 x .139) |
| 20 |
25-8M0204645 |
O-RING, (.796 x .139) |
| 21 |
8M0114707 |
POPPET ASSEMBLY |
| 22 |
24-64878 |
SPRING, (Black) |
| 23 |
893385001 |
RETAINER |
| 24 |
648771 |
DIAPHRAGM |
| 25 |
889706 |
WASHER |
| 26 |
10-69570 |
SCREW, (#10-16 x .750) |
| 27 |
893384001 |
COVER, Poppet |
| 28 |
27-889561 |
GASKET, Poppet |
| 29 |
10-88552535 |
SCREW, (M6 x 35 MM) Stainless Steel |
▶Alternator/Belt Tensioner Mounting (18 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
892940T02 |
ALTERNATOR |
| 2 |
8M0101707 |
BELT TENSIONER |
| 3 |
8M6003035 |
PULLEY |
| 4 |
10-885349501 |
SCREW |
| 5 |
23-855729 |
MOUNT |
| 6 |
12-845998 |
WASHER, (.406 x 1.250 x .089) |
| 7 |
10-8M0103823 |
SCREW, (M10 x 45) |
| 8 |
8M0219204 |
BRACKET |
| 9 |
17-888517 |
PIN |
| 10 |
57-8M0232583 |
BELT, Drive |
| 11 |
10-8M0103824 |
SCREW, (M10 x 85) |
| 12 |
12-4002319 |
WASHER |
| 13 |
11-401386 |
NUT, (M6) Stainless Steel |
| 14 |
84-856583A12 |
CABLE ASSEMBLY |
| 15 |
84-858414A04 |
CABLE ASSEMBLY, Brass, Braided |
| 16 |
10-8M0103805 |
SCREW, (M6 x 16 MM) Stainless Steel |
| 17 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 18 |
54-828991T |
CLIP |
▶Charge Cooler/Intake Manifold (39 parts)
| Ref |
OEM Part # |
Part Name |
| - |
8M0185616 |
MODULE ASSEMBLY, Integrated Air Fuel |
| 1 |
8M0132388 |
CAC ASSEMBLY |
| 2 |
19-8M0048079 |
PLUG , 8MM |
| 3 |
8M0046698 |
END CAP ASSEMBLY |
| 4 |
25-8M0039516 |
O-RING |
| 5 |
53-8M0039464 |
RING, Retaining |
| 6 |
25-8M0040116 |
O-RING |
| 7 |
22-8M0039993 |
FITTING |
| 8 |
8M0083678 |
MANIFOLD ASSEMBLY, Intake |
| 9 |
895019 |
SEAL, Manifold to CAC |
| 10 |
895020 |
SEAL, Manifold Head |
| 11 |
891663001 |
SENSOR ASSEMBLY, Temperature |
| 12 |
10-895054 |
SCREW |
| 13 |
25-892317001 |
O-RING |
| 14 |
10-88552514 |
SCREW, (M6 x 14 MM) Stainless Steel, CAC to Manifold |
| 15 |
10-8M0103807 |
SCREW, (M6 x 25 MM) Stainless Steel, Manifold to CAC |
| 16 |
8M6000639 |
SENSOR, Pressure |
| 17 |
54-8M0214911 |
CLAMP, (15.7) |
| 18 |
8M0041053 |
BOOT, MAP Sensor |
| 19 |
54-8M0204719 |
CLAMP, (36.1 mm) |
| 20 |
8M0185167 |
FUEL RAIL ASSEMBLY |
| 21 |
32-8M0047054 |
TUBE KIT, Fuel Inlet |
| 22 |
NSS |
NOT SOLD SEPARATE, O-ring Tube |
| 23 |
8M0041097 |
BRACKET, Retaining |
| 24 |
10-8M0041100 |
SCREW, (M5 x 10) |
| 25 |
21-8M0102769 |
VALVE KIT, Schrader |
| 26 |
NSS |
NOT SOLD SEPARATE, O-ring- Shrader Valve |
| 27 |
8M0041097 |
BRACKET, Retaining |
| 28 |
10-8M0041100 |
SCREW, (M5 x 10) |
| 29 |
NSS |
NOT SOLD SEPARATE, FUEL RAIL |
| 30 |
8M0041096 |
BRACKET, Fuel Injector Mounting |
| 31 |
8M0222155 |
INJECTOR ASSEMBLY, Fuel |
| 32 |
10-8M0041100 |
SCREW, (M5 x 10) |
| 33 |
8M0041101 |
DAMPER, Fuel Rail |
| 34 |
25-851889 |
O-RING, Damper |
| 35 |
8M0103315 |
PITOT SENSOR KIT |
| 36 |
22-8M0207782 |
FITTING |
| 37 |
54-883066 |
CLIP, (.865) |
| 38 |
22-8M0214970 |
FITTING, Adapter |
▶Charge Cooler/Intake Manifold Hose Routings (11 parts)
| Ref |
OEM Part # |
Part Name |
| - |
NSS |
NOT SOLD SEPARATE, Hose Assembly |
| 1 |
11-826292 |
NUT, (M10) Brass/Nickel Plated |
| 2 |
10-8M0048051 |
SCREW, (M6 x 30) Stainless Steel |
| 3 |
32-889593001 |
HOSE |
| 4 |
22-8M6003382 |
FITTING ASSEMBLY, Flushing |
| 5 |
32-889592001 |
HOSE |
| 6 |
54-8M0187145 |
CLAMP, (34.6 mm) |
| 7 |
32-892967 |
HOSE |
| 8 |
54-850181 |
TIE STRAP, (11.750 Inches) |
| 9 |
32-8M0203773 |
HOSE, Manifold Reference |
| 10 |
10-8M0103821 |
SCREW, (M10 x 30) |
▶Cowl Latching (13 parts)
| Ref |
OEM Part # |
Part Name |
| - |
8M0142168 |
LATCH ASSEMBLY, Front and Side |
| 1 |
888976T01 |
BRACKET |
| 2 |
888974A02 |
SIDE LATCH ASSEMBLY |
| 3 |
24-888996 |
SPRING |
| 4 |
23-896124 |
SLEEVE |
| 5 |
25-828249 |
GROMMET |
| 6 |
8M0153958 |
CABLE |
| 7 |
53-27290 |
RING, Retaining |
| 8 |
12-30164 |
WASHER, (.192 x .375 x .0312) Stainless Steel |
| 9 |
17-893380 |
PIN, Clevis |
| 10 |
53-61319 |
E RING |
| 11 |
10-4006731 |
SCREW, (M6 x 16) |
| 12 |
16-8M0099404 |
STUD |
▶Crankshaft, Pistons and Connecting Rods (18 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-896966A06 |
LONG BLOCK ASSEMBLY |
| 1 |
400-891644A04 |
CRANKSHAFT ASSEMBLY |
| 2 |
23-897498T08 |
BEARING, Main (Orange) |
| 3 |
23-8M0117004 |
BEARING, Thrust - Orange, Crankshaft-Lower |
| 4 |
26-8M0032912 |
SEAL, Top Main Bearing |
| 5 |
23-896883 |
SPACER |
| 6 |
53-896882 |
RING, Retaining |
| 7 |
28-91800 |
KEY, Woodruff |
| 8 |
8M0103398 |
CHAIN, Roller Cam Drive |
| 9 |
662-8M0103285 |
CONNECTING ROD ASSEMBLY |
| 10 |
10-884441 |
BOLT |
| 11 |
23-892005A03 |
BEARING, Connecting Rod - Orange |
| 12 |
700-8M0104286 |
PISTON ASSEMBLY |
| 13 |
39-881180A02 |
RING SET, Piston |
| 14 |
NSS |
NOT SOLD SEPARATE, Piston Ring-Oil |
| 15 |
NSS |
NOT SOLD SEPARATE, Piston Ring-2nd |
| 16 |
NSS |
NOT SOLD SEPARATE, Piston Pin |
| 17 |
40-896594 |
CIRCLIP |
▶Cylinder Block (31 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-896966A06 |
LONG BLOCK ASSEMBLY |
| 1 |
800-880506A12 |
CYLINDER BLOCK ASSEMBLY |
| 2 |
8M0111325 |
BRACKET, Mounting-Starter Motor |
| 3 |
10-8M0103815 |
SCREW, (M8 x 40) |
| 4 |
19-889767 |
PLUG, (12 mm) |
| 5 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) |
| 6 |
23-893392001 |
DAMPER |
| 7 |
19-896951 |
PLUG, (24 mm) |
| 8 |
17-880524 |
PIN, Dowel (14 MM) |
| 9 |
25-884409 |
O-RING |
| 10 |
17-884424 |
PIN, Dowel (11 mm) |
| 11 |
25-884423 |
O-RING |
| 12 |
10-8M4501000 |
SCREW, (M10 X 342) |
| 13 |
12-892573001 |
WASHER |
| 14 |
10-8M0103818 |
SCREW, (M8 x 75) |
| 15 |
8M0082988 |
CRANKSHAFT POSITION SENSOR |
| 16 |
10-40011107 |
SCREW, (M5 x 16) Stainless Steel |
| 17 |
8M0142542 |
SENSOR ASSEMBLY |
| 18 |
25-896699 |
O-RING, (1.78 mm x .08 mm) |
| 19 |
8M6000637 |
SENSOR, Pressure |
| 20 |
27-8M0033476 |
GASKET, Head |
| 21 |
17-888517 |
PIN |
| 22 |
10-8M0193831 |
SCREW, (M8 x 115) |
| 23 |
10-8M0193659 |
SCREW, (M8 x 50) |
| 24 |
27-880624003 |
GASKET, Block to Adaptor |
| 25 |
880559 |
GUIDE, Fixed |
| 26 |
880557 |
GUIDE, Moveable |
| 27 |
10-892456045 |
SCREW |
| 28 |
16-8M0022160 |
STUD, (M8 x 43) |
| 29 |
11-401388 |
NUT, (M8) Stainless Steel |
| 30 |
10-8M0103814 |
SCREW, (M8 x 35 MM) |
▶Cylinder Head and Camshaft (54 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-896966A06 |
LONG BLOCK ASSEMBLY |
| 1 |
900-8M0152336 |
CYLINDER HEAD ASSEMBLY, Basic |
| 2 |
19-8M0087448 |
PLUG, (12 MM) |
| 3 |
19-8M0087451 |
PLUG, (18 MM) |
| 4 |
19-8M0087453 |
PLUG, (24 MM) |
| 5 |
19-8M0087446 |
PLUG, (10 MM) |
| 6 |
17-880524 |
PIN, Dowel (14 MM) |
| 7 |
10-8M0163131 |
BOLT, (M6 x 36) |
| 8 |
880533 |
SEAT, Intake Valve |
| 9 |
8M0089477 |
SEAT, Exhaust Seat |
| 10 |
880537 |
GUIDE, Intake Exhaust Valve |
| 11 |
20-898907 |
VALVE, Intake |
| 12 |
20-8M0032471 |
VALVE, Exhaust |
| 13 |
26-8M0214986 |
SEAL, Valve |
| 14 |
24-8M0103092 |
SPRING VALVE KIT, Intake and Exhaust |
| 15 |
8M0908500 |
RETAINER ASSEMBLY, Valves |
| 16 |
28-880543 |
KEY |
| 17 |
NSS |
NOT SOLD SEPARATE, CAP |
| 18 |
400-8M0150209 |
CAMSHAFT, Intake |
| 19 |
400-8M0150210 |
CAMSHAFT, Exhaust |
| 20 |
899912035 |
TAPPET, (3.721) |
| 21 |
892596T04 |
COVER ASSEMBLY, Cam |
| 22 |
892584 |
SEAL |
| 23 |
8M6000959 |
SEAL |
| 24 |
10-8M0103807 |
SCREW, (M6 x 25 MM) Stainless Steel |
| 25 |
859578A1 |
PLUG ASSEMBLY, Oil |
| 26 |
25-8M0204673 |
O-RING, (.921 x .139) |
| 27 |
19-8M0087447 |
PLUG , (10MM) |
| 28 |
25-896699 |
O-RING, (1.78 mm x .08 mm) |
| 29 |
10-8M0103817 |
SCREW, (M8 x 60) |
| 30 |
898463A01 |
TENSIONER ASSEMBLY |
| 31 |
25-898836 |
O-RING, Brown |
| 32 |
1100-8M0064752 |
END CAP - CAM TENSIONER , Tensioner |
| 33 |
10-8M0103807 |
SCREW, (M6 x 25 MM) Stainless Steel |
| 34 |
10-8M0103809 |
SCREW, (M6 x 40 MM) Stainless Steel |
| 35 |
10-8M0103814 |
SCREW, (M8 x 35 MM) |
| 36 |
12-817274 |
WASHER, (.344 x 1.00 x .063) Stainless Steel |
| 37 |
25-833155 |
GROMMET |
| 38 |
23-8502341 |
BUSHING |
| 39 |
54-892833 |
CLIP |
| 40 |
32-889591A05 |
HOSE ASSEMBLY, Breather |
| 41 |
339-880615T01 |
COIL ASSEMBLY |
| 42 |
10-8M0103807 |
SCREW, (M6 x 25 MM) Stainless Steel |
| 43 |
33-889246Q39 |
SPARK PLUG, NGK-ILFR6GE |
| 44 |
54-858954 |
CLIP, (.625) |
| 45 |
54-850181 |
TIE STRAP, (11.750 Inches) |
| 46 |
43-880550 |
SPROCKET, Cam Drive |
| 47 |
10-8M0021532 |
SCREW, (M12 x 40 MM) Comment: (Left Hand) |
| 48 |
10-8M0103804 |
SCREW, (M6 x 12 MM) Stainless Steel |
| 49 |
54-889746001 |
CLIP |
| 50 |
54-888988019 |
CLAMP, (22.6 mm) |
| 51 |
8M0011987 |
SENSOR |
| 52 |
10-8M0103805 |
SCREW, (M6 x 16 MM) Stainless Steel |
| 53 |
25-8M0119617 |
GROMMET, Rubber |
▶Decals - Top Cowl (13 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
37-8M0102448 |
DECAL SET, Mercury |
| 2 |
37-8M0103041 |
DECAL SET, ME Verado Pro |
| 3 |
37-8M0103042 |
DECAL SET, ME Verado Racing, Black, Does not contain Carbon Decals |
| 4 |
37-8M0103043 |
DECAL SET, ME Verado Racing, White |
| 5 |
37-8M0097812 |
DECAL KIT, 400R Racing Carbon |
| 6 |
37-8M0043703 |
M-ICON, 66 mm, Black |
| 7 |
37-8M0080153 |
M-ICON, 66 MM Racing |
| 8 |
37-8M0085367 |
DECAL, 350 HP, Rear |
| 9 |
37-8M0075217 |
DECAL, Joystick Piloting |
| 10 |
37-8M0099017 |
DECAL, Joystick Piloting, Silver |
| 11 |
37-8M0090899 |
DECAL, 350 Pro, Top |
| 12 |
37-8M0090898 |
DECAL, 350 Pro, Rear |
| 13 |
37-8M0043699 |
DECAL M-ICON, Red, 66mm |
▶Driveshaft Housing (35 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
1500-8M0113287 |
HOUSING, Driveshaft X-Long, Black |
| 2 |
25-889568001 |
GROMMET |
| 3 |
889656T01 |
SHROUD |
| 4 |
10-8M0103818 |
SCREW, (M8 x 75) |
| 5 |
10-8M0103812 |
SCREW, (M8 x 120) |
| 6 |
10-8M0103816 |
SCREW, (M8 x 50) |
| 7 |
10-8M0103815 |
SCREW, (M8 x 40) |
| 8 |
10-8M0103814 |
SCREW, (M8 x 35 MM) |
| 9 |
12-817274 |
WASHER, (.344 x 1.00 x .063) Stainless Steel |
| 10 |
897784A01 |
BRACKET KIT, Upper Chap |
| 11 |
10-8M0103806 |
SCREW, (M6 x 20 MM) Stainless Steel |
| 12 |
10-8M0103813 |
SCREW, (M8 x 30) |
| 13 |
32-85944975 |
TUBING, (72.00 Inches Bulk), Cut to 44 Inches) |
| 14 |
889831001 |
RETAINER |
| 15 |
NSS |
NOT SOLD SEPARATE, Decal-Oil Drain |
| 16 |
16-8M0008031 |
STUD, (M12 x 1.75 x 52) Comment: (Long/X-Long) |
| 17 |
12-856982 |
WASHER, (.500 x .810 x .090) Stainless Steel |
| 18 |
11-896895 |
NUT, (M12) |
| 19 |
10-8M0102995 |
SCREW, (M12) Comment: (Long/X-Long) |
| 20 |
19-824928001 |
PLUG, Rubber |
| 21 |
12-8M0214963 |
WASHER, (.406 x .750 x .105) Stainless Steel |
| 22 |
11-884412 |
NUT |
| 23 |
10-8M0103825 |
SCREW, (M12 x 45) |
| 24 |
8M0146468 |
SPACER, Driveshaft Housing X-Long, Silver Comment: (XX-Long) |
| 25 |
10-857137 |
SCREW, (M12 x 160) Comment: (XX-Long) |
| 26 |
16-8M0008047 |
STUD, (M12 x 179) Comment: (XX-Long) |
| 27 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) Comment: (XX-Long) |
| 28 |
891966006 |
BRACKET, Cowl Comment: (X-Long/XX-Long) |
| 29 |
8M0103333 |
PLATES ASSEMBLY, Thrust, X-Long |
| 30 |
NSS |
NOT SOLD SEPARATE, Thrust Plate - X-Long |
| 31 |
10-8M0090182 |
SCREW, (M8 X 120) |
| 32 |
11-8M0088686 |
NUT, (M8 X 1.25) |
| 33 |
17-8M0095755 |
PIN, Dowel |
| 34 |
8M0080471 |
BUMPER, Trim |
| 35 |
10-8M0103816 |
SCREW, (M8 x 50) |
▶Electrical Box Components (45 parts)
| Ref |
OEM Part # |
Part Name |
| - |
NSS |
NOT SOLD SEPARATE, Relay Bracket Assembly |
| 1 |
885560T03 |
BASE, Electrical Box |
| 2 |
885561T |
COVER, Fuse Box |
| 3 |
88-8M0167280 |
COVER, Fuse |
| 4 |
25-885583 |
SEAL |
| 5 |
889531 |
STRAP |
| 6 |
885584 |
PIN, Hinge |
| 7 |
25-833155 |
GROMMET |
| 8 |
23-8502341 |
BUSHING |
| 9 |
88-832969T20 |
FUSE, Mini - Yellow - 20 Ampere |
| 10 |
11-400213 |
NUT, (M8) Stainless Steel |
| 11 |
895099 |
EXTRACTOR, Fuse |
| 12 |
32-828547753 |
CONDUIT, (.750 Inside Diameter x 3.00 Feet Bulk) |
| 13 |
10-40011146 |
SCREW, (M8 x 13) Stainless Steel |
| 14 |
12-843108 |
WASHER, (.330 x .560 x .060) Stainless Steel |
| 15 |
12-817274 |
WASHER, (.344 x 1.00 x .063) Stainless Steel |
| 16 |
892244 |
STRAP, Cover |
| 17 |
54-879962 |
CLIP |
| 18 |
8M0103435 |
PROPULSION CONTROL MODULE, 400 (2-Star) |
| 19 |
84-8M0102454 |
HARNESS ASSEMBLY, Engine |
| 20 |
882751A04 |
RELAY ASSEMBLY |
| 21 |
NSS |
NOT SOLD SEPARATE, Decal-Trim Relay |
| 22 |
889532 |
BRACKET |
| 23 |
10-40007103 |
SCREW, (M5 x 6) |
| 24 |
84-93388A17 |
CABLE ASSEMBLY, (8.50 Inches) |
| 25 |
84-879345T34 |
HARNESS ASSEMBLY, Trim |
| 26 |
84-8M0088927 |
HARNESS ASSEMBLY, Fuse |
| 27 |
830796A03 |
CONNECTOR ASSEMBLY, Weather Cap - 2 Pin Male |
| 28 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 29 |
10-82129114 |
SCREW, (M6 x 14) |
| 30 |
877613A02 |
CONNECTOR ASSEMBLY, Weather Cap 6 Pin |
| 31 |
54-879962 |
CLIP |
| 32 |
84-8M0113732 |
HARNESS ASSEMBLY |
| 33 |
862646 |
FUSE, Tan - 5 Ampere |
| 34 |
84-88439A25 |
CABLE ASSEMBLY, Battery - Positive Comment: (Long) |
| 35 |
11-401388 |
NUT, (M8) Stainless Steel |
| 36 |
11-8M0204671 |
NUT, (.375-16), Battery Cable-Positive |
| 37 |
10-8M0103814 |
SCREW, (M8 x 35 MM) |
| 38 |
12-817274 |
WASHER, (.344 x 1.00 x .063) Stainless Steel |
| 39 |
84-88439A26 |
CABLE ASSEMBLY, Battery - Negative Comment: (Long) |
| 40 |
11-8M0204668 |
NUT, (.312-18), Battery Cable-Negative |
| 41 |
54-891520001 |
CLIP |
| 42 |
37-8M0087378 |
DECAL , Maintenance Schedule |
| 43 |
893388A01 |
CAP, Resitor - 2 Pin, 120 Ohm (CAN 1, 2 and 3) |
| 44 |
8M0055652 |
TERMINATOR ASSEMBLY, 10 Pin (CAN 1P and H) |
▶Flywheel and Cover (7 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
8M0102451 |
COVER, Flywheel |
| 2 |
25-8M0153609 |
GROMMET |
| 3 |
200-888983T03 |
FLYWHEEL ASSEMBLY |
| 4 |
12-8M0090010 |
WASHER |
| 5 |
10-8M0147042 |
BOLT, (M20 x 68) |
| 6 |
37-8M0103480 |
DECAL SET, Flywheel Cover, 350 Pro |
| 7 |
37-8M0103479 |
DECAL SET, Flywheel Cover, 400R |
▶Fuel Filter Kits (18 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
98-8M0103686 |
FUEL FILTER KIT, Engine Mounted, Optional |
| 2 |
35-8M0062950 |
FILTER ASSEMBLY |
| 3 |
35-8M0122423 |
FILTER, Fuel |
| 4 |
8M0009261 |
BRACKET ASSEMBLY |
| 5 |
10-8M0103824 |
SCREW, (M10 x 85) |
| 6 |
84-8M0103724 |
HARNESS, WIF Extension |
| 7 |
32-8M0099411 |
HOSE ASSEMBLY, Fuel Inlet |
| 8 |
22-892356 |
CONNECTOR |
| 9 |
32-8M0087107 |
HOSE |
| 10 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 11 |
8M0157707 |
FUEL FILTER KIT, with o-ring, MPP, Remote Mounted |
| 12 |
8M0157616 |
FUEL FILTER ASSEMBLY, with o-ring, MPP |
| 13 |
8M0095674 |
BASE ASSEMBLY, Fuel Filter |
| 14 |
22-816133 |
FITTING |
| 15 |
22-8M0204657 |
PLUG, (.375-18) Hex - Steel |
| 16 |
22-8M0204732 |
CONNECTOR, Barb |
| 17 |
8M0214989 |
SENSOR ASSEMBLY, Fuel and Water |
| 18 |
84-8M0042697 |
HARNESS |
▶Fuel Supply Module (24 parts)
| Ref |
OEM Part # |
Part Name |
| - |
8M0057679 |
FSM SEAL KIT |
| 1 |
10-8M0053756 |
SCREW, Plastite W/ HX WSR HD |
| 2 |
8M0158344 |
FSM TOP HOUSING |
| 3 |
NSS |
NOT SOLD SEPARATE, O-ring |
| 4 |
8M0053749 |
REGULATOR ASSEMBLY |
| 5 |
NSS |
NOT SOLD SEPARATE, O-ring |
| 6 |
NSS |
NOT SOLD SEPARATE, O-ring |
| 7 |
NSS |
NOT SOLD SEPARATE |
| 8 |
NSS |
NOT SOLD SEPARATE |
| 9 |
8M0053727 |
FSM CAP |
| 10 |
NSS |
NOT SOLD SEPARATE |
| 11 |
8M0103289 |
PUMP ASSEMBLY, Low Pressure |
| 12 |
8M0103288 |
PUMP ASSEMBLY, High Pressure |
| 13 |
NSS |
NOT SOLD SEPARATE, O-ring |
| 14 |
32-8M0119250 |
TUBE |
| 15 |
32-8M0053755 |
TUBE |
| 16 |
NSS |
NOT SOLD SEPARATE, O-ring |
| 17 |
8M0120073 |
TUBE |
| 18 |
NSS |
NOT SOLD SEPARATE, Seal |
| 19 |
8M0053725 |
FSM BOTTOM HOUSING |
| 20 |
84-8M0103287 |
HARNESS ASSEMBLY, FSM |
| 21 |
NSS |
NOT SOLD SEPARATE, O-ring |
| 22 |
NSS |
NOT SOLD SEPARATE, O-ring |
| 23 |
NSS |
NOT SOLD SEPARATE, Spacer |
▶Gear Housing,, Driveshaft, 5.44 HD Sportmaster (43 parts)
| Ref |
OEM Part # |
Part Name |
| - |
25-8M0065072 |
WATER PUMP REPAIR KIT, Upper |
| 1 |
1600-8M0137075 |
GEAR HOUSING ASSEMBLY, Basic Comment: Counter Cambered Skeg |
| 2 |
847635001 |
ANODE |
| 3 |
12-841388 |
WASHER, (.410 x .810 x .050) Stainless Steel |
| 4 |
10-8M0036047 |
SCREW, (.375 x .62) |
| 5 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) |
| 6 |
817275A1 |
HOUSING KIT, Water Pump |
| 7 |
10-8M0204706 |
SCREW, (M6 x 20) |
| 8 |
26-8M0142851 |
SEAL, Face |
| 9 |
47-43026Q02 |
IMPELLER |
| 10 |
27-8172771 |
GASKET |
| 11 |
8M0204709 |
FACEPLATE |
| 12 |
27-8M0142616 |
GASKET |
| 13 |
28-8M0204723 |
KEY |
| 14 |
8M0046297 |
OIL SEAL ASSEMBLY |
| 15 |
NSS |
NOT SOLD SEPARATE, SEAL |
| 16 |
25-8M0142854 |
O-RING, (2.175 x .103) |
| 17 |
53-880719 |
RING, Retaining |
| 18 |
8245191 |
RETAINER |
| 19 |
15-8M0063267 |
SHIM SET |
| 20 |
31-8M0146566 |
BEARING ASSEMBLY, Roller/Cup |
| 21 |
31-8M0146553 |
BEARING, Tapered Roller |
| 22 |
15-8M0063268 |
SHIM SET |
| 23 |
45-8M0141338 |
SHAFT, Drive, Long |
| 24 |
31-8M0045676 |
BEARING, Roller |
| 25 |
43-8M0053120 |
GEAR SET, 12/21 (1.75:1), Forward and Pinion Comment: Counter Rotation |
| 26 |
12-8M0062703 |
WASHER, Pinon nut |
| 27 |
11-8M0046636 |
NUT, Pinion |
| 28 |
43585 |
COUPLING |
| 29 |
10-8M0204706 |
SCREW, (M6 x 20) |
| 30 |
8M0050809 |
GROMMET ASSEMBLY |
| 31 |
8M0047129 |
COVER ASSEMBLY |
| 32 |
25-896522 |
O-RING, (799 x .103) |
| 33 |
26-8M0204708 |
SEAL, Oil |
| 34 |
53-8M0046563 |
RETAINING RING |
| 35 |
22-881866 |
FITTING |
| 36 |
27-880729 |
GASKET |
| 37 |
53-29641 |
E RING |
| 38 |
8M0050602 |
MAGNET |
| 39 |
8M0046104 |
SHIFT SHAFT |
| 40 |
22-859732 |
PLUG Comment: 1.75:1 Ratio |
| 41 |
8M0094053 |
PLATE, Water Passage |
| 42 |
27-8M0094054 |
GASKET, Water Passage |
▶Gear Housing,, Driveshaft, 5.44 Torpedo (44 parts)
| Ref |
OEM Part # |
Part Name |
| - |
25-8M0065072 |
WATER PUMP REPAIR KIT, Upper |
| 1 |
1600-8M0228048 |
GEAR HOUSING ASSEMBLY, Basic, Silver |
| 2 |
97-826134Q |
ANODE |
| 3 |
10-4000333 |
SCREW, (M6 x 40) |
| 4 |
11-401386 |
NUT, (M6) Stainless Steel |
| 5 |
97-76214Q5 |
ANODE KIT |
| 6 |
10-8M0204686 |
SCREW, (.437-14 x 1.750) |
| 7 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) |
| 8 |
8M0010459 |
FILLER BLOCK |
| 9 |
817275A1 |
HOUSING KIT, Water Pump |
| 10 |
10-8M0204706 |
SCREW, (M6 x 20) |
| 11 |
26-8M0142851 |
SEAL, Face |
| 12 |
47-43026Q02 |
IMPELLER |
| 13 |
27-8172771 |
GASKET |
| 14 |
8M0204709 |
FACEPLATE |
| 15 |
27-8M0142616 |
GASKET |
| 16 |
28-8M0204723 |
KEY |
| 17 |
8M0046297 |
OIL SEAL ASSEMBLY |
| 18 |
NSS |
NOT SOLD SEPARATE, SEAL |
| 19 |
25-8M0142854 |
O-RING, (2.175 x .103) |
| 20 |
53-880719 |
RING, Retaining |
| 21 |
8245191 |
RETAINER |
| 22 |
15-8M0063267 |
SHIM SET |
| 23 |
31-8M0146566 |
BEARING ASSEMBLY, Roller/Cup |
| 24 |
31-8M0146553 |
BEARING, Tapered Roller |
| 25 |
15-8M0063268 |
SHIM SET |
| 26 |
45-8M0141338 |
SHAFT, Drive, Long |
| 27 |
31-8M0045676 |
BEARING, Roller |
| 28 |
43-8M0053120 |
GEAR SET, 12/21 (1.75:1), Forward and Pinion Comment: Counter Rotation |
| 29 |
12-8M0062703 |
WASHER, Pinon nut |
| 30 |
11-8M0046636 |
NUT, Pinion |
| 31 |
43585 |
COUPLING |
| 32 |
10-8M0204706 |
SCREW, (M6 x 20) |
| 33 |
8M0050809 |
GROMMET ASSEMBLY |
| 34 |
8M0047129 |
COVER ASSEMBLY |
| 35 |
25-896522 |
O-RING, (799 x .103) |
| 36 |
26-8M0204708 |
SEAL, Oil |
| 37 |
53-8M0046563 |
RETAINING RING |
| 38 |
22-881866 |
FITTING |
| 39 |
27-880729 |
GASKET |
| 40 |
53-29641 |
E RING |
| 41 |
8M0050602 |
MAGNET |
| 42 |
8M0046104 |
SHIFT SHAFT |
| 43 |
22-859732 |
PLUG Comment: 1.75:1 Ratio |
▶Gear Housing,, Prop Shaft-Counter Rot, 5.44 HD Sportmaster (36 parts)
| Ref |
OEM Part # |
Part Name |
| - |
1600-8M0137083 |
GEAR HOUSING ASSEMBLY, Complete (XX-Long) (1.75:1) Cambered Skeg |
| 1 |
1600-8M0137075 |
GEAR HOUSING ASSEMBLY, Basic, Counter Cambered Skeg |
| 2 |
8M0235941 |
SPOOL ASSEMBLY |
| 3 |
NSS |
NOT SOLD SEPARATE, SPOOL |
| 4 |
NSS |
NOT SOLD SEPARATE, SLEEVE |
| 5 |
18-469501 |
COTTER PIN |
| 6 |
8M0220880 |
CRANK, Shifter, 1/4 Pivot Pin |
| 7 |
15-8M0063270 |
SHIM SET |
| 8 |
43-8M0053121 |
GEAR KIT, Reverse Comment: 1.75:1 Ratio |
| 9 |
31-8M0142836 |
BEARING ASSEMBLY, Roller |
| 10 |
31-8M0142835 |
BEARING ASSEMBLY, Roller-Tappered |
| 11 |
12-8M0053823 |
THRUST WASHER |
| 12 |
53-8M0051043 |
RETAINING RING |
| 13 |
17-8M0045493 |
PIN |
| 14 |
52-8M0053113 |
CLUTCH |
| 15 |
24-8M0050575 |
SPRING |
| 16 |
44-8M0142764 |
PROPELLER SHAFT, 1.25 Inch Comment: 1.75:1 Ratio |
| 17 |
23-8M0064306 |
SPACER |
| 18 |
43-8M0053120 |
GEAR SET, 12/21 (1.75:1), Forward |
| 19 |
31-8M0050692 |
BEARING |
| 20 |
12-8M0050688 |
WASHER |
| 21 |
15-8M0053116 |
SHIM SET |
| 22 |
8M0053183 |
ADAPTOR |
| 23 |
8M0117237 |
CARRIER ASSEMBLY, Bearing |
| 24 |
25-8M0000190 |
O-RING, (4.475 x .210) |
| 25 |
26-8M0204700 |
SEAL, Oil |
| 26 |
31-8M0148319 |
BEARING ASSEMBLY, Tapered |
| 27 |
10-8M0071653 |
SCREW, Special |
| 28 |
26-8M0204693 |
SEAL |
| 29 |
53-8M0056639 |
RING, Retainer |
| 30 |
31-8M0050704 |
BEARING, Needle |
| 31 |
14-8M0108527 |
TAB WASHER |
| 32 |
8M0162798 |
NUT, Retainer |
| 33 |
8M0180306 |
COVER KIT, Flush, Standard |
| 35 |
10-8M0036819 |
SET SCREW, (10-32) |
| 36 |
12-8M0161546 |
RING, Thrust |
▶Gear Housing,, Prop Shaft-Counter Rot, 5.44 Torpedo (37 parts)
| Ref |
OEM Part # |
Part Name |
| - |
1600-8M0228055 |
GEAR HOUSING ASSEMBLY, Complete, Silver (XX-Long) (1.75:1) |
| 1 |
1600-8M0228048 |
GEAR HOUSING ASSEMBLY, Basic, Silver |
| 2 |
8M0235941 |
SPOOL ASSEMBLY |
| 3 |
NSS |
NOT SOLD SEPARATE, SPOOL |
| 4 |
NSS |
NOT SOLD SEPARATE, SLEEVE |
| 5 |
18-469501 |
COTTER PIN |
| 6 |
8M0220880 |
CRANK, Shifter, 1/4 Pivot Pin |
| 7 |
15-8M0063270 |
SHIM SET |
| 8 |
43-8M0053121 |
GEAR KIT, Reverse Comment: 1.75:1 Ratio |
| 9 |
31-8M0142836 |
BEARING ASSEMBLY, Roller |
| 10 |
31-8M0142835 |
BEARING ASSEMBLY, Roller-Tappered |
| 11 |
12-8M0053823 |
THRUST WASHER |
| 12 |
53-8M0051043 |
RETAINING RING |
| 13 |
17-8M0045493 |
PIN |
| 14 |
52-8M0053113 |
CLUTCH |
| 15 |
24-8M0050575 |
SPRING |
| 16 |
44-8M0142764 |
PROPELLER SHAFT, 1.25 Inch Comment: 1.75:1 Ratio |
| 17 |
23-8M0064306 |
SPACER |
| 18 |
43-8M0053120 |
GEAR SET, 12/21 (1.75:1), Forward |
| 19 |
31-8M0050692 |
BEARING |
| 20 |
12-8M0050688 |
WASHER |
| 21 |
15-8M0053116 |
SHIM SET |
| 22 |
8M0053183 |
ADAPTOR |
| 23 |
8M0117237 |
CARRIER ASSEMBLY, Bearing |
| 24 |
25-8M0000190 |
O-RING, (4.475 x .210) |
| 25 |
26-8M0204700 |
SEAL, Oil |
| 26 |
31-8M0148319 |
BEARING ASSEMBLY, Tapered |
| 27 |
10-8M0071653 |
SCREW, Special |
| 28 |
26-8M0204693 |
SEAL |
| 29 |
12-8M0050439 |
WASHER, .050 |
| 30 |
53-8M0056639 |
RING, Retainer |
| 31 |
31-8M0050704 |
BEARING, Needle |
| 32 |
14-8M0108527 |
TAB WASHER |
| 33 |
8M0162798 |
NUT, Retainer |
| 34 |
8M0180306 |
COVER KIT, Flush, Standard |
| 35 |
10-8M0036819 |
SET SCREW, (10-32) |
| 36 |
12-8M0161546 |
RING, Thrust |
▶Gear Housing,, Prop Shaft-Standard Rot, 5.44 HD Sportmaster (36 parts)
| Ref |
OEM Part # |
Part Name |
| - |
1600-8M0137080 |
GEAR HOUSING ASSEMBLY, Complete (XX-Long) (1.75:1) Cambered Skeg |
| 1 |
1600-8M0137073 |
GEAR HOUSING ASSEMBLY, Basic, Standard Cambered Skeg |
| 2 |
8M0235941 |
SPOOL ASSEMBLY |
| 3 |
NSS |
NOT SOLD SEPARATE, SPOOL |
| 4 |
NSS |
NOT SOLD SEPARATE, SLEEVE |
| 5 |
18-469501 |
COTTER PIN |
| 6 |
8M0220880 |
CRANK, Shifter, 1/4 Pivot Pin |
| 7 |
15-8M0063270 |
SHIM SET |
| 8 |
43-8M0078258 |
GEAR SET, 12/21(1.75:1), Forward |
| 9 |
31-8M0142836 |
BEARING ASSEMBLY, Roller |
| 10 |
31-8M0142835 |
BEARING ASSEMBLY, Roller-Tappered |
| 11 |
12-8M0053823 |
THRUST WASHER |
| 12 |
53-8M0051043 |
RETAINING RING |
| 13 |
17-8M0045493 |
PIN |
| 14 |
52-8M0053113 |
CLUTCH |
| 15 |
24-8M0050575 |
SPRING |
| 16 |
44-8M0142764 |
PROPELLER SHAFT, 1.25 Inch Comment: 1.75:1 Ratio |
| 17 |
23-8M0064306 |
SPACER |
| 18 |
43-8M0053124 |
GEAR KIT, Reverse Comment: 1.75:1 Ratio |
| 19 |
31-8M0050692 |
BEARING |
| 20 |
12-8M0050688 |
WASHER |
| 21 |
15-8M0053116 |
SHIM SET |
| 22 |
8M0053183 |
ADAPTOR |
| 23 |
8M0117238 |
CARRIER ASSEMBLY, Bearing |
| 24 |
25-8M0000190 |
O-RING, (4.475 x .210) |
| 25 |
26-8M0204700 |
SEAL, Oil |
| 26 |
31-8M0148319 |
BEARING ASSEMBLY, Tapered |
| 27 |
10-8M0071653 |
SCREW, Special |
| 28 |
26-8M0204693 |
SEAL |
| 29 |
53-8M0056639 |
RING, Retainer |
| 30 |
31-8M0050704 |
BEARING, Needle |
| 31 |
14-8M0108527 |
TAB WASHER |
| 32 |
8M0162798 |
NUT, Retainer |
| 33 |
8M0180308 |
COVER KIT |
| 34 |
10-8M0036819 |
SET SCREW, (10-32) |
| 35 |
12-8M0161546 |
RING, Thrust |
▶Gear Housing,, Prop Shaft-Standard Rot, 5.44 Torpedo (37 parts)
| Ref |
OEM Part # |
Part Name |
| - |
1600-8M0228067 |
GEAR HOUSING ASSEMBLY, Complete, Silver (XX-Long) (1.75:1) |
| 1 |
1600-8M0228048 |
GEAR HOUSING ASSEMBLY, Basic, Silver |
| 2 |
8M0235941 |
SPOOL ASSEMBLY |
| 3 |
NSS |
NOT SOLD SEPARATE, SPOOL |
| 4 |
NSS |
NOT SOLD SEPARATE, SLEEVE |
| 5 |
18-469501 |
COTTER PIN |
| 6 |
8M0220880 |
CRANK, Shifter, 1/4 Pivot Pin |
| 7 |
15-8M0063270 |
SHIM SET |
| 8 |
43-8M0078258 |
GEAR SET, 12/21(1.75:1), Forward |
| 9 |
31-8M0142836 |
BEARING ASSEMBLY, Roller |
| 10 |
31-8M0142835 |
BEARING ASSEMBLY, Roller-Tappered |
| 11 |
12-8M0053823 |
THRUST WASHER |
| 12 |
53-8M0051043 |
RETAINING RING |
| 13 |
17-8M0045493 |
PIN |
| 14 |
52-8M0053113 |
CLUTCH |
| 15 |
24-8M0050575 |
SPRING |
| 16 |
44-8M0142764 |
PROPELLER SHAFT, 1.25 Inch Comment: 1.75:1 Ratio |
| 17 |
23-8M0064306 |
SPACER |
| 18 |
43-8M0053124 |
GEAR KIT, Reverse Comment: 1.75:1 Ratio |
| 19 |
31-8M0050692 |
BEARING |
| 20 |
12-8M0050688 |
WASHER |
| 21 |
15-8M0053116 |
SHIM SET |
| 22 |
8M0053183 |
ADAPTOR |
| 23 |
8M0117238 |
CARRIER ASSEMBLY, Bearing |
| 24 |
25-8M0000190 |
O-RING, (4.475 x .210) |
| 25 |
26-8M0204700 |
SEAL, Oil |
| 26 |
31-8M0148319 |
BEARING ASSEMBLY, Tapered |
| 27 |
10-8M0071653 |
SCREW, Special |
| 28 |
26-8M0204693 |
SEAL |
| 29 |
12-8M0050439 |
WASHER, .050 |
| 30 |
53-8M0056639 |
RING, Retainer |
| 31 |
31-8M0050704 |
BEARING, Needle |
| 32 |
14-8M0108527 |
TAB WASHER |
| 33 |
8M0162798 |
NUT, Retainer |
| 34 |
8M0180306 |
COVER KIT, Flush, Standard |
| 35 |
10-8M0036819 |
SET SCREW, (10-32) |
| 36 |
12-8M0161546 |
RING, Thrust |
▶Ground Cable Kit(899712A01) (5 parts)
| Ref |
OEM Part # |
Part Name |
| - |
899712A01 |
CABLE KIT, Continuity |
| 1 |
88238T23 |
CABLE ASSEMBLY |
| 2 |
88238T24 |
CABLE ASSEMBLY |
| 3 |
12-8M0217559 |
WASHER |
| 4 |
25-12602002 |
GROMMET |
▶Induction Components (37 parts)
| Ref |
OEM Part # |
Part Name |
| - |
8M0103293 |
TUBE ASSEMBLY, Hot Air Duct |
| 1 |
8M0103295 |
INTAKE ASSEMLY, Duct |
| 2 |
8M0103362 |
SCREEN, Upper Intake |
| 3 |
10-8M6003202 |
SCREW |
| 4 |
8M0103291 |
INTAKE ASSEMBLY, Lower |
| 5 |
54-8M6003032 |
CLAMP, Inlet to Resonator |
| 6 |
25-8349851 |
GROMMET |
| 7 |
23-856954 |
BUSHING |
| 8 |
12-65567 |
WASHER, (.265 x .750 x .048) Stainless Steel |
| 9 |
10-8M0103807 |
SCREW, (M6 x 25 MM) Stainless Steel |
| 10 |
32-8M0095507 |
HOSE, CAC Tube |
| 11 |
8M0095505 |
TUBE, CAC |
| 12 |
8M0095506 |
HOSE, CAC Tube |
| 13 |
54-888988021 |
CLAMP, Oetiker |
| 14 |
54-8M6003214 |
CLAMP |
| 15 |
8M0089697 |
DUCT, Inlet |
| 16 |
54-888988016 |
CLAMP, (96.5 mm) |
| 17 |
8M0113515 |
CONTROL ASSEMBLY, Throttle - Electronic |
| 18 |
8M0113513 |
ISOLATOR |
| 19 |
54-815504256 |
CLAMP, Worm Gear |
| 20 |
10-88552550 |
SCREW, (M6 x 50 MM) Stainless Steel |
| 21 |
884353 |
BRACKET |
| 22 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 23 |
898022 |
DIPSTICK, Oil |
| 24 |
884408A08 |
VALVE KIT, Control - Electric Boost |
| 25 |
887939007 |
PLATE, Boost Valve Mounting |
| 26 |
25-892079 |
O-RING |
| 27 |
10-8M0103806 |
SCREW, (M6 x 20 MM) Stainless Steel |
| 28 |
25-833155 |
GROMMET |
| 29 |
23-8502341 |
BUSHING |
| 30 |
54-859376 |
CLIP |
| 31 |
10-8M0103814 |
SCREW, (M8 x 35 MM) |
| 32 |
12-817274 |
WASHER, (.344 x 1.00 x .063) Stainless Steel |
| 33 |
32-887937006 |
HOSE |
| 34 |
54-888988002 |
CLAMP, (57.5 mm) |
| 35 |
32-887938003 |
TUBE, Rear |
| 36 |
54-888988004 |
CLAMP, (62.0 mm) |
▶Lower Cowl (8 parts)
| Ref |
OEM Part # |
Part Name |
| - |
100-8M0100562 |
CHAPS ASSEMBLY, X-Long, Port and Starboard, Warm Fusion |
| 1 |
NSS |
NOT SOLD SEPARATE, Lower Port Chap (X-Long-XX-Long) |
| 2 |
NSS |
NOT SOLD SEPARATE, Lower Starboard Chap (X-Long-XX-Long) |
| 3 |
10-892073002 |
SHOULDER SCREW, (M6), X-Long- XX-Long Chaps |
| 4 |
54-898033 |
CLIP |
| 5 |
100-8M0100565 |
COVER, Chaps, Front, Warm Fusion |
| 6 |
10-8M0027847 |
SCREW, (M6 x 25) |
| 7 |
11-863149 |
NUT, Well (M6 x 10) |
▶Mercathode Kit (15 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
88334A2 |
MERCATHODE KIT |
| 2 |
42600A09 |
MERCATHODE ASSEMBLY |
| 3 |
10-22793 |
SCREW, (#9-14 x .875) |
| 4 |
12-30164 |
WASHER, (.192 x .375 x .0312) Stainless Steel |
| 5 |
10-32,11-45076 |
NUT, Brass |
| 6 |
72958A5 |
ELECTRODE ASSEMBLY |
| 7 |
25-8M0204645 |
O-RING, (.796 x .139) |
| 8 |
10-87698 |
SCREW, (#10-16 x 1.250) Stainless Steel |
| 9 |
97-72957A5 |
ANODE ASSEMBLY |
| 10 |
25-8M0204645 |
O-RING, (.796 x .139) |
| 11 |
10-87698 |
SCREW, (#10-16 x 1.250) Stainless Steel |
| 12 |
88-8M0207796 |
FUSE, 20 Ampere |
| 13 |
84-95084A10 |
CABLE ASSEMBLY, (5.00 Inches) Red |
| 14 |
84-95084A13 |
CABLE ASSEMBLY, (64.00 Inches) |
| 15 |
84-79138A8 |
CABLE ASSEMBLY, (72.00 Inches) Black |
▶Mount Cradle (23 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
8M0109275 |
SEAL |
| 2 |
884887T05 |
CRADLE, Mount |
| 3 |
NSS |
NOT SOLD SEPARATE, Seal |
| 4 |
8M0102452 |
MOUNT, Rear |
| 5 |
8M0103375 |
MOUNT, Front |
| 6 |
10-889745030 |
SCREW, (M12 x 30) |
| 7 |
10-8M0103832 |
SCREW, (M16 x 90) |
| 8 |
25-12602002 |
GROMMET |
| 9 |
10-40011126 |
SCREW, (M6 x 13) Stainless Steel |
| 10 |
32-8M0108355 |
HOSE, (57.00 Inches Bulk), Cut to 35 Inches |
| 11 |
22-895797001 |
FITTING, Telltale |
| 12 |
54-895851 |
CLAMP, (8.00 Inches) |
| 13 |
17-73194 |
PIN, Roll (.125 x 1.12) |
| 14 |
880649002 |
LEVER, Tilt Lock |
| 15 |
24-47968 |
SPRING |
| 16 |
889540A03 |
CLUTCH KIT |
| 17 |
8M0109693 |
BRACKET, Tilt Lock |
| 18 |
8M0076907 |
PAD, Tilt Lock |
| 19 |
880650003 |
SHAFT, Tilt Lock |
| 20 |
10-889546 |
SCREW, (M5 x 10) |
| 21 |
31-8806641 |
BEARING, (.625 Inch) |
| 22 |
888590002 |
SENSOR, Trim Position |
| 23 |
10-889547 |
SCREW, (M5 x 30) |
▶Oil Pump/Adaptor Plate-Upper (29 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-896966A06 |
LONG BLOCK ASSEMBLY |
| 1 |
892126A03 |
ADAPTOR PLATE KIT |
| 2 |
17-892228 |
PIN, Dowel |
| 3 |
19-896951 |
PLUG, (24 mm) |
| 4 |
26-884462 |
SEAL, Water |
| 5 |
25-887930 |
O-RING |
| 6 |
26-8M0033928 |
SEAL, Oil |
| 7 |
21-8M0034048 |
VALVE ASSEMBLY, Oil Pump |
| 8 |
8M6002692 |
CHAIN, Oil Pump Drive, Oil Pump Drive |
| 9 |
12-892491 |
WASHER |
| 10 |
11-892165 |
NUT |
| 11 |
45-8M0217265 |
DRIVESHAFT, Oil Pump |
| 12 |
25-8M0034912 |
O-RING, 3.78 X 21.32 |
| 13 |
895063001 |
INSERT, Plastic |
| 14 |
884418A1 |
TENSIONER ASSEMBLY, Oil Pump Drive |
| 15 |
884446T04 |
PUMP ASSEMBLY, Oil |
| 16 |
10-892455065 |
SCREW |
| 17 |
892335001 |
DEFLECTOR, Oil |
| 18 |
10-8M0103805 |
SCREW, (M6 x 16 MM) Stainless Steel |
| 19 |
888819002 |
DRAIN, Cowl |
| 20 |
25-888163 |
GROMMET |
| 21 |
19-8M0027347 |
PLUG, (M18 x 1.5) |
| 22 |
22-8M0092321 |
FITTING, Dump |
| 23 |
25-8M0092943 |
O-RING |
| 24 |
10-8M0103804 |
SCREW, (M6 x 12 MM) Stainless Steel |
| 25 |
19-8M0088815 |
PLUG, Panel |
| 26 |
32-8M0084506 |
HOSE, Fuel Inlet , Fuel inlet to Fuel Supply Module |
| 27 |
27-889617001 |
GASKET |
| 28 |
884456 |
SPROCKET, Driven |
▶Port Cylinder Block Components (18 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-896966A06 |
LONG BLOCK ASSEMBLY |
| 1 |
16-8M0022158 |
STUD, (M10 x 205) |
| 2 |
16-8M0022162 |
STUD, (M10 x 60) |
| 3 |
8M6002872 |
SENSOR ASSEMBLY, Knock |
| 4 |
10-892086035 |
SCREW, (M10 x 35) |
| 5 |
12-4002319 |
WASHER |
| 6 |
11-826365 |
NUT, (M8) |
| 7 |
54-8M0187145 |
CLAMP, (34.6 mm) |
| 8 |
32-8M0043736 |
HOSE |
| 9 |
22-896094A01 |
FITTING ASSEMBLY |
| 10 |
25-896699 |
O-RING, (1.78 mm x .08 mm) |
| 11 |
32-85978571 |
TUBING, (52.00 Inches Bulk), To Water Pressure Sensor - Cut to 21.5 Inches |
| 12 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 13 |
881879T26 |
SENSOR, Pressure, Water |
| 14 |
16-8M0000274 |
STUD, (M8 x 44) |
| 15 |
22-885517A05 |
FITTING ASSEMBLY |
| 16 |
25-892077 |
O-RING |
| 17 |
893388A02 |
CAP, Resistor - 2 Pin, 20K Ohm |
▶Power Trim Components (19 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
8M0118298 |
TRIM CYLINDER KIT |
| 2 |
8M0118299 |
TRIM ROD KIT |
| 3 |
896158A01 |
O-RING KIT |
| 4 |
896159A01 |
PISTON KIT |
| 5 |
896166A01 |
MANIFOLD KIT, Trim |
| 6 |
896165A01 |
CHECK KIT, Trim PO |
| 7 |
896160A01 |
O-RING KIT |
| 8 |
97-8M0217563 |
ANODE |
| 9 |
8M0001735 |
PAD, Wear |
| 10 |
10-8M0199587 |
SCREW, (M6 x 20) |
| 11 |
896163A01 |
PUMP KIT, Trim |
| 12 |
35-896164A01 |
TRIM FILTER KIT |
| 13 |
896162A01 |
TRIM NECK KIT |
| 14 |
25-895854A01 |
O-RING KIT |
| 15 |
19-893419 |
CAP KIT |
| 16 |
8M0224397 |
MANUAL RELEASE KIT |
| 17 |
17-893408A01 |
PIN KIT, Trim |
| 18 |
896161A02 |
TRIM MOTOR KIT |
| 19 |
896167A01 |
RESERVOIR KIT |
▶Power Trim/Transom Assembly (44 parts)
| Ref |
OEM Part # |
Part Name |
| - |
NSS |
NOT SOLD SEPARATE, Transom Assembly |
| 1 |
880652T02 |
PEDESTAL |
| 2 |
896500A01 |
STEERING CYLINDER KIT Comment: (Standard) |
| 3 |
8M0168425 |
RETAINER |
| 4 |
12-895853 |
WASHER |
| 5 |
10-88509530 |
SCREW, (M8 x 30) |
| 6 |
22-889552 |
ELBOW Comment: (Standard) |
| 7 |
889550 |
CAP, Bleeder - Vinyl Comment: (Standard) |
| 8 |
25-8M0155530 |
SEAL |
| 9 |
8M0045604 |
SEAL KIT, Steering Cylinder |
| 10 |
22-892524 |
CAP, Fitting Comment: (Standard) |
| 11 |
31-8M0217557 |
BEARING |
| 12 |
26-8M0217558 |
SEAL |
| 13 |
31-8M0217560 |
BEARING |
| 14 |
8M0103373 |
HEAD, Steering |
| 15 |
31-8M0001758 |
BEARING, With Shoulder |
| 16 |
10-885094105 |
SCREW, (M14 x 105) |
| 17 |
12-8M0217559 |
WASHER |
| 18 |
88238T23 |
CABLE ASSEMBLY |
| 19 |
8M0217564 |
COVER |
| 20 |
880665T01 |
ARM, Steering |
| 21 |
97-8M0217561 |
ANODE |
| 22 |
10-4010720 |
SCREW, (M8 x 20) |
| 23 |
8M0220571 |
TUBE, Steering |
| 24 |
17-885111 |
PIN, Dowel (.375 x .875) |
| 25 |
880658T02 |
POWER TRIM ASSEMBLY |
| 26 |
25-895854 |
O-RING |
| 27 |
97-893404 |
ANODE |
| 28 |
12-8M0161430 |
WASHER |
| 29 |
97-893404 |
ANODE |
| 30 |
10-8M0007798 |
SCREW, (M10 x 65) |
| 31 |
17-8M0146467 |
PIN, Rod Eye |
| 32 |
17-821539 |
PIN, Trilobe |
| 33 |
53-895304 |
RING, Retaining |
| 34 |
10-8M0038370 |
SCREW, (.500-20 x 5.50) |
| 35 |
12-8M0204704 |
WASHER |
| 36 |
12-8M0204648 |
WASHER, (1.5 x 3.05 x 0.13) Stainless Steel |
| 37 |
11-82671117 |
NUT, (.500-20) |
| 38 |
NSS |
NOT SOLD SEPARATE, Decal-Serial Overlaminate |
| 39 |
8M0001803 |
TILT PIN |
| 40 |
25-8M0032468 |
SPACER |
| 41 |
53-8M6000694 |
RETAINING RING |
| 42 |
19-95925 |
PLUG |
| 43 |
37-8M0043059 |
DECAL, Warning |
▶Powerhead Gasket Set Components (1 parts)
| Ref |
OEM Part # |
Part Name |
| - |
25-8M0034912 |
O-RING, 3.78 X 21.32 , Oil Pump Driveshaft |
▶Pump Kit-Power Steering(4 thru 24 Feet) (23 parts)
| Ref |
OEM Part # |
Part Name |
| - |
893365A03 |
COVER ASSEMBLY, Top/Bottom, Power Steering Pump Comment: (Includes both Top 893365T02 and Bottom 893364T02 Covers) |
| 1 |
NSS |
NOT SOLD SEPARATE, PUMP |
| 2 |
892485003 |
CAP, Pump |
| 3 |
NSS |
NOT SOLD SEPARATE, DECAL, Fluid Type |
| 4 |
893364A05 |
ENCLOSURE ASSEMBLY, Complete-Power Steering Pump Comment: (Complete Enclosure Assembly fits all versions) |
| 5 |
893365T02 |
ENCLOSURE ASSEMBLY, Top, Power Steering Pump |
| 6 |
8M0080707 |
ENCLOSURE ASSEMBLY, Bottom-Power Steering Pump |
| 7 |
889531 |
STRAP |
| 8 |
21-817519A2 |
CHECK VALVE ASSEMBLY, Drain |
| 9 |
25-893368001 |
GROMMET |
| 10 |
25-893369 |
GROMMET |
| 11 |
54-815504206 |
CLAMP, Worm Gear |
| 12 |
12-8M0214930 |
WASHER |
| 13 |
11-401366 |
NUT, (M6) Stainless Steel |
| 14 |
10-895378 |
SCREW, (M6) |
| 15 |
25-895319 |
GROMMET |
| 16 |
12-8M0214930 |
WASHER |
| 17 |
23-895320F1 |
BUSHING |
| 18 |
88-79023A94 |
FUSE ASSEMBLY, 50 Ampere |
| 19 |
879346T24 |
FUSE COVER AND O-RING |
| 20 |
8M0026568 |
HARNESS ASSEMBLY, Signal Driver |
| 21 |
32-897643A01 |
HOSE KIT, Dampening |
| 22 |
25-89879 |
O-RING, (.301 x .064) |
▶Rear Cowl (26 parts)
| Ref |
OEM Part # |
Part Name |
| - |
100-8M0100563 |
SEAL ASSEMBLY, Rear Cowl, Port and Starboard |
| 1 |
100-8M0100177 |
REAR COWL ASSEMBLY, Warm Fusion, Non-Decaled |
| 2 |
17-888961A01 |
PIN ASSEMBLY |
| 3 |
11-892233 |
NUT, (M6) Stainless Steel |
| 4 |
885360 |
IDLE RELIEF |
| 5 |
100-8M0100563 |
SEAL ASSEMBLY, Rear Cowl, Port and Starboard |
| 6 |
NSS |
NOT SOLD SEPARATE, Seal, Starboard |
| 7 |
NSS |
NOT SOLD SEPARATE, FRONT COWL, Port |
| 8 |
NSS |
NOT SOLD SEPARATE, FRONT COWL, Starboard |
| 9 |
27-892315 |
GASKET |
| 10 |
8M0043266 |
SEAL |
| 11 |
25-888957 |
O-RING |
| 12 |
8M0224266 |
TETHER |
| 13 |
87-8M0235191 |
SWITCH, Trim |
| 14 |
8M0215105 |
PLUG, Flush |
| 15 |
11-892233 |
NUT, (M6) Stainless Steel |
| 16 |
12-8M0214930 |
WASHER |
| 17 |
22-885361A01 |
FITTING ASSEMBLY, Flush |
| 18 |
10-4006731 |
SCREW, (M6 x 16) |
| 19 |
54-858951A01 |
CLAMP KIT |
| 20 |
12-8M0214930 |
WASHER |
| 21 |
10-4006731 |
SCREW, (M6 x 16) |
| 22 |
11-892233 |
NUT, (M6) Stainless Steel |
| 23 |
8M0214997 |
ADAPTOR |
| 24 |
25-8M0214987 |
GROMMET |
| 25 |
8M4501634 |
SOUND BLANKET KIT |
▶Service/Support Material (1 parts)
| Ref |
OEM Part # |
Part Name |
| - |
NSS |
NOT SOLD SEPARATE, DECAL, EPA (2009 & Up) Comment: (Contact Mercury Marine Warranty Administration for Replacement-Service Bulletin 2009-18) |
▶Starboard Cylinder Block/Oil Cooler (39 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-896966A06 |
LONG BLOCK ASSEMBLY |
| 1 |
892404A05 |
DEFLECTOR ASSEMBLY, Water |
| 2 |
22-885518A02 |
FITTING ASSEMBLY |
| 3 |
25-62701 |
O-RING |
| 4 |
10-8M0103805 |
SCREW, (M6 x 16 MM) Stainless Steel |
| 5 |
54-888988011 |
CLAMP, (38.1 mm) |
| 6 |
32-888930003 |
HOSE, Cyl Block to IOM |
| 7 |
54-8M0187145 |
CLAMP, (34.6 mm) |
| 8 |
8M0174561 |
THERMOSTAT ASSEMBLY |
| 9 |
25-8M0005958 |
O-RING |
| 10 |
54-8M0204719 |
CLAMP, (36.1 mm) |
| 11 |
32-892865 |
HOSE, Thermostat |
| 12 |
54-888988007 |
CLAMP, (42.5 mm) |
| 13 |
54-78945 |
J CLAMP |
| 14 |
10-8M0103824 |
SCREW, (M10 x 85) |
| 15 |
10-8M0103820 |
SCREW, (M10 x 105) |
| 16 |
8M0132390 |
MODULE, Integrated Oil |
| 17 |
NSS |
NOT SOLD SEPARATE, Oil Cooler Housing |
| 18 |
19-891953 |
PLUG, (18 mm) |
| 19 |
8M0046698 |
END CAP ASSEMBLY |
| 20 |
53-8M0039464 |
RING, Retaining |
| 21 |
25-8M0039516 |
O-RING |
| 22 |
35-877769K01 |
FILTER, Oil (Mercury Branded) |
| 23 |
8M0046693 |
THERMOSTAT ASSEMBLY |
| 24 |
NSS |
NOT SOLD SEPARATE, Thermostat Stop |
| 25 |
NSS |
NOT SOLD SEPARATE, SPRING |
| 26 |
19-8M0046697 |
PLUG |
| 27 |
NSS |
NOT SOLD SEPARATE, O-RING |
| 28 |
8M0046696 |
ADAPTOR ASSEMBLY (Contains 2 Adaptors) |
| 29 |
NSS |
NOT SOLD SEPARATE, O-RING |
| 30 |
8M0046694 |
HOUSING ASSEMBLY |
| 31 |
27-8M0034568 |
GASKET |
| 32 |
10-8M0103805 |
SCREW, (M6 x 16 MM) Stainless Steel |
| 33 |
10-82129125 |
SCREW, (M6 x 25 MM) |
| 34 |
12-65567 |
WASHER, (.265 x .750 x .048) Stainless Steel |
| 35 |
10-8M0103807 |
SCREW, (M6 x 25 MM) Stainless Steel |
| 36 |
23-822003 |
BUSHING |
| 37 |
25-8M0190980 |
GROMMET |
| 38 |
8M0007908 |
BRACKET |
▶Starter Motor (15 parts)
| Ref |
OEM Part # |
Part Name |
| - |
NSS |
NOT SOLD SEPARATE, Starter Motor Assembly |
| 1 |
50-892339T01 |
STARTER MOTOR ASSEMBLY |
| 2 |
NSS |
NOT SOLD SEPARATE, Screws |
| 3 |
43-880805A1 |
GEAR KIT |
| 4 |
809463A1 |
SOLENOID KIT |
| 5 |
8M0065258 |
BRUSH SET |
| 6 |
23-8M0034918 |
COLLAR |
| 7 |
8M0043276 |
STOP |
| 8 |
NSS |
NOT SOLD SEPARATE, Decal-Waring-High Voltage |
| 9 |
84-93388A1 |
CABLE ASSEMBLY, (6.00 Inches) Black |
| 10 |
10-69035 |
SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel |
| 11 |
13-8M0204647 |
LOCKWASHER, (.312) |
| 12 |
11-400213 |
NUT, (M8) Stainless Steel |
| 13 |
13-400255 |
LOCKWASHER, (M5) |
| 14 |
11-400211 |
NUT, (M5) Stainless Steel |
▶Steering Helm Kit-Standard(892557A02, 892380A02, 892558A02) (11 parts)
| Ref |
OEM Part # |
Part Name |
| - |
8M0137449 |
STEERING HELM KIT, Standard (50 cc) |
| 1 |
8M0137448 |
HELM, Standard (50 cc) |
| 2 |
25-627021 |
O-RING, (.301 x .070) |
| 3 |
25-48171 |
O-RING, (.364. x .070) |
| 4 |
28-893394 |
KEY, With Lock Tab (6.35 mm) |
| 5 |
10-4008850 |
SCREW, (M6 x 50) |
| 6 |
11-826709121 |
NUT, (.625-18) Stainless Steel |
| 7 |
892328T |
COVER, Helm |
| 8 |
10-896842 |
SCREW, (M6 x 14) |
| 9 |
892327 |
PLATE, Helm Backing Comment: (892558A02) |
| 10 |
11-401196 |
NUT, (M6) |
▶SuperCharger (12 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
8M0102453 |
SUPERCHARGER |
| 2 |
8M0148668 |
SENSOR ASSEMBLY |
| 3 |
25-896699 |
O-RING, (1.78 mm x .08 mm) |
| 4 |
8M0104083 |
DUCT ASSEMBLY, Inlet |
| 5 |
27-888947501 |
GASKET |
| 6 |
22-8M0138655 |
FITTING, Water, Supercharger |
| 7 |
10-88552514 |
SCREW, (M6 x 14 MM) Stainless Steel |
| 8 |
10-888947502 |
BOLT |
| 9 |
22-8M6003432 |
FITTING, Water, Supercharger |
| 10 |
8M6003433 |
FITTING, Water, Supercharger |
| 11 |
56762 |
TIE STRAP, (4.00 Inches) |
| 12 |
10-8M0103820 |
SCREW, (M10 x 105) |
▶Tools (11 parts)
| Ref |
OEM Part # |
Part Name |
| - |
91-896661 |
TOOL, Fuel Filter |
| 1 |
91-805382T01 |
TOOL, Extension-Dial Indicator |
| 2 |
91-8M0046443 |
TOOL, Height Gageing, pinion |
| 3 |
91-8M0046348 |
TOOL, Bearing Driver, Pinion Removal |
| 4 |
91-8M0036288 |
TOOL, Holder, Pinion Nut |
| 5 |
91-8M0046632 |
TOOL, Socket, Carrier Retainer Nut |
| 6 |
91-8M0046360 |
TOOL, Bearing Driver, Pinion Install |
| 7 |
91-8M0050615 |
TOOL, Holder, Shift Shaft |
| 8 |
91-8M0053505 |
TOOL, Indicator, Backlash |
| 9 |
91-8M0035594 |
TOOL, Propeller Shaft Holder |
| 10 |
91-8M0052590 |
TOOL, Driver, Upper Driveshaft Bearing |
▶Top Cowl (20 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
100-8M0113903 |
TOP COWL ASSEMBLY, Cold Fusion, Non-Decaled |
| 2 |
8M0090475 |
CAP, Air Dam, Warm Fusion |
| 3 |
888971 |
FRONT LATCH RECEIVER |
| 4 |
8M0111178 |
SEAL |
| 5 |
8M0153959 |
CABLE, Latch |
| 6 |
17-888959 |
PIN, Hinge |
| 7 |
888956 |
LATCH, Hand Lever |
| 8 |
24-895373 |
SPRING |
| 9 |
888955 |
LINK, Latch Connecting |
| 10 |
18-26953 |
COTTER PIN |
| 11 |
12-89302 |
WASHER, (.203 x .406 x .040) |
| 12 |
888952 |
LINKAGE ARM |
| 13 |
24-888953 |
SPRING |
| 14 |
17-822417 |
PIN |
| 15 |
10-897678020 |
SCREW, (M4 x 20mm) (M4 x 1.75) |
| 16 |
8M0088808 |
APPLIQUE, Port, Warm Fusion |
| 17 |
8M0088810 |
APPLIQUE, Starboard, Warm Fusion |
| 18 |
10-8M0103804 |
SCREW, (M6 x 12 MM) Stainless Steel |
| 19 |
8M4501639 |
SOUND BLANKET KIT |
| 20 |
8M0096745 |
SOUND BLANKET, Air Cap |
▶Upper Shift Components (20 parts)
| Ref |
OEM Part # |
Part Name |
| - |
8M0103311 |
BRACKET ASSEMBLY, Front Mount |
| 1 |
NSS |
NOT SOLD SEPARATE, Bracket |
| 2 |
23-892417 |
BUSHING |
| 3 |
23-8M0047763 |
SPACER |
| 4 |
8M0047949 |
SHIFT SHAFT |
| 5 |
889727001 |
BELL CRANK |
| 6 |
17-25319 |
PIN, (.125 x 0.75 Inches) |
| 7 |
25-833155 |
GROMMET |
| 8 |
23-85999 |
BUSHING |
| 9 |
8M0124413 |
SHIFT ACTUATOR |
| 10 |
10-8855091 |
SCREW |
| 11 |
18-885512 |
COTTER PIN |
| 12 |
12-885511003 |
WASHER |
| 13 |
17-895770 |
Pin, Pivot |
| 14 |
10-8M0207826 |
SCREW, (M10 x 155) |
| 15 |
10-8M0103802 |
SCREW, (M14) |
| 16 |
11-8M0045046 |
NUT, (M6) Stainless Steel |
| 17 |
23-97896 |
BUSHING |
| 18 |
885505 |
LINK, Shift Shaft |
| 19 |
8M0180097 |
SHAFT, Shift, (XX-Long) |
100-Hour / Annual Service Checklist
Regular maintenance keeps your Mercury 350 PRO VERADO (4-Stroke)(6 CYL.) running reliably season after season. Most of these tasks can be performed with basic tools and the factory service manual.
- Replace water pump impeller and inspect wear plate
- Change engine oil and oil filter (check drain plug washer)
- Replace spark plugs and check ignition timing
- Drain and refill lower unit gear oil; inspect for water contamination
- Inspect fuel lines, primer bulb, and fuel filter for deterioration
- Check and replace sacrificial anodes (zinc or aluminum)
- Inspect propeller for damage; check shaft seal and cotter pin
- Check valve clearance (refer to service manual for specifications)
- Lubricate all grease points (steering, tilt tube, shift linkage)
- Inspect control cables and throttle/shift linkage for smooth operation
-
Pro Tip: Always flush the engine with fresh water after saltwater use — even a quick 10-minute flush significantly extends component life.
-
Pro Tip: Use fuel stabilizer in the tank before winter storage, and fog the cylinders to prevent internal corrosion during extended periods of non-use.