🔎 Mercury 250 PRO XS (3.0L DFI) Reference Library — Exploded parts diagrams (29 diagrams), specifications, common issues, and maintenance checklist.
The Mercury 250 PRO XS (3.0L DFI) is a 4-Stroke, V8 64-degree, DOHC, 32-valve outboard motor. Designed for large center-consoles, offshore sport-fishing boats, and multi-engine configurations.
Quick Reference Specifications
| Specification |
Value |
| Engine Type |
4-Stroke, V8 64-degree, DOHC, 32-valve |
| Horsepower |
250 HP |
| Displacement |
4600 cc (4.6L / 279 CID) |
| Bore x Stroke |
92 mm x 86 mm (3.62 in. x 3.38 in.) |
| Spark Plug (Type & Gap) |
NGK LKAR7C-9 |
| Engine Oil Capacity |
7.0 L (7.4 qt) |
| Recommended Engine Oil |
Mercury FourStroke Oil 25W-40 (NMMA FC-W SAE 10W-30) |
| Gear Case Oil Capacity |
802 mL (27.1 oz) |
| Idle Speed (in gear) |
600 RPM |
| Full Throttle RPM Range |
5200-6000 |
| Fuel |
Unleaded Gasoline, 87 Octane min. |
Always verify specifications against your owner's manual for your specific serial number range.
Common Issues & Recommended Parts
Below are common maintenance scenarios for the Mercury 250 PRO XS (3.0L DFI):
-
Water Pump / Overheating: If the tell-tale stream is weak or absent, the water pump impeller likely needs replacement. Inspect annually or every 100 hours. → Recommended: Water Pump Impeller Kit
-
Engine Oil / Maintenance Light: 4-stroke engines require regular oil and filter changes. Use marine-grade oil rated for your engine. Change every 100 hours or annually. → Recommended: Oil Filter, Engine Oil
-
Fuel Injector Issues (EFI models): Rough idle or misfires may indicate clogged fuel injectors. Use fuel stabilizer and clean injectors periodically. → Recommended: Fuel Injector, Fuel Filter
-
Gear Case Oil Leak: Check lower unit seals if gear oil appears milky (water contamination). Replace seals and gaskets during lower unit service. → Recommended: Lower Unit Seal Kit, Drain Plug Gaskets
-
Anode Corrosion: Inspect sacrificial anodes regularly, especially in saltwater. Replace when 50% depleted to protect against galvanic corrosion. → Recommended: Zinc/Aluminum Anode Kit
Parts Diagrams & OEM Part Numbers
Expand the sections below to view detailed exploded parts diagrams and find the exact OEM replacement components for your Mercury 250 PRO XS (3.0L DFI).
▶Air Compressor Components (31 parts)
| Ref |
OEM Part # |
Part Name |
| - |
25-832804A03 |
O-RING KIT |
| 1 |
8M0060051 |
COMPRESSOR ASSEMBLY, Air Comment: Unpainted |
| 2 |
1100-8M0050793 |
END CAP ASSEMBLY |
| 3 |
NSS |
NOT SOLD SEPARATE, Snap Ring |
| 4 |
10-85593920 |
SCREW, (M6 x 20) |
| 5 |
25-89224001 |
O-RING |
| 6 |
25-67206001 |
O-RING |
| 7 |
653-833146T06 |
CONNECTING ROD ASSEMBLY |
| 8 |
NSS |
NOT SOLD SEPARATE, Piston Assembly |
| 9 |
53-8348101 |
RING, Lock |
| 10 |
835088A10 |
REED PLATE ASSEMBLY |
| 11 |
25-67207 |
O-RING, (3.489 x .070) |
| 12 |
25-832804 |
O-RING, (2.739 x .070) |
| 13 |
26-828225 |
SEAL |
| 14 |
835087A3 |
HEAD ASSEMBLY, Compressor |
| 15 |
22-8307535 |
FITTING, Straight |
| 16 |
10-82127335 |
SCREW, (M8 x 35 MM) |
| 17 |
22-151331 |
FITTING |
| 18 |
22-996642 |
FITTING, Elbow 90 Degree (.125-27 x .250) Nylon |
| 19 |
21-428641 |
FITTING, Check Valve |
| 20 |
22-856744 |
FITTING |
| 21 |
22-16604 |
FITTING, Straight (.125-27) |
| 22 |
25-831985 |
O-RING, (.468 x .078) |
| 23 |
13536A14 |
SENSOR ASSEMBLY, Temperature |
| 24 |
137151 |
RETAINER |
| 25 |
10-81893414 |
SCREW, (M8 x 14) |
| 26 |
22-390721 |
PLUG, Pipe (.125-27) Brass |
| 27 |
10-85593920 |
SCREW, (M6 x 20) |
| 28 |
8M0138680 |
PULLEY |
| 29 |
10-8M0045380 |
SCREW, (M8 x 50) |
| 30 |
12-884594 |
WASHER |
▶Air Handler (53 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-841017A52 |
POWERHEAD ASSEMBLY |
| 1 |
858541T4 |
ADAPTOR PLATE |
| 2 |
27-841220 |
GASKET |
| 3 |
840418T04 |
REED BLOCK ASSEMBLY |
| 4 |
34-840445A04 |
REED PETAL ASSEMBLY |
| 5 |
10-849038 |
SCREW, (M3 x 5) |
| 6 |
840447 |
REED PLATE |
| 7 |
10-8555252 |
SCREW, (M6) |
| 8 |
23-855364 |
BUSHING |
| 9 |
25-855362001 |
GROMMET |
| 10 |
12-817274 |
WASHER, (.344 x 1.00 x .063) Stainless Steel |
| 11 |
10-81893435 |
SCREW, (M8 x 35) |
| 12 |
8M0001447 |
BRACKET |
| 13 |
858708T1 |
PLENUM KIT, Air |
| 14 |
27-804679004 |
GASKET |
| 15 |
10-883942 |
SCREW, (M4 x 16) |
| 16 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 17 |
54-804842 |
CLAMP |
| 18 |
8M0185614 |
PUMP ASSEMBLY, Oil |
| 19 |
854445 |
SENSOR, MAP |
| 20 |
884522 |
BRACKET, MAP Sensor |
| 21 |
10-1993716 |
SCREW, (M6 x 16) |
| 22 |
8M0148668 |
SENSOR ASSEMBLY |
| 23 |
25-896699 |
O-RING, (1.78 mm x .08 mm) |
| 24 |
841194T04 |
THROTTLE BODY ASSEMBLY |
| 25 |
23-891774 |
BUSHING |
| 26 |
853659A01 |
LEVER KIT, Throttle |
| 27 |
858851A03 |
LEVER ASSEMBLY, Throttle |
| 28 |
8M0072162 |
ROLLER |
| 29 |
12-8M0204666 |
WASHER, (.203 x .500 x .032) |
| 30 |
8-32,11-826709104 |
NUT, Stainless Steel |
| 31 |
10-889354 |
SCREW, Special |
| 32 |
12-881991 |
WASHER, Cupped |
| 33 |
12-881992 |
WASHER, Spool |
| 34 |
10,13-69432 |
LOCKWASHER, External |
| 35 |
10-82130040 |
SCREW, (M6 x 40) |
| 36 |
25-855426 |
O-RING |
| 37 |
8M0111168 |
COVER |
| 38 |
25-86361 |
GROMMET |
| 39 |
25-13467 |
GROMMET, (.88 Inside Diameter) |
| 40 |
25-8M0153609 |
GROMMET |
| 41 |
37-881865 |
DECAL, Caution-Start in Gear |
| 42 |
854343T11 |
ATTENUATOR, Air |
| 43 |
10-82130050 |
SCREW, (M6 x 50) |
| 44 |
12-69056 |
WASHER, (.255 x .620 x .030) Stainless Steel |
| 45 |
54-858902 |
CLAMP |
| 46 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 47 |
10-82130040 |
SCREW, (M6 x 40) |
| 48 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 49 |
881879T25 |
SENSOR ASSEMBLY, Pitot |
| 50 |
881879T11 |
SENSOR, Pressure (0 - 100 PSI) |
| 51 |
22-8M0207782 |
FITTING |
| 52 |
54-883066 |
CLIP, (.865) |
▶Air Hoses (11 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-841017A52 |
POWERHEAD ASSEMBLY |
| 1 |
22-856842 |
ELBOW |
| 2 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 3 |
32-8M0108349 |
TUBING, (.312) (70.00 Inches Bulk) (Cut to 8 Inches) |
| 4 |
54-8M0214964 |
CLAMP, Hose (15.3) |
| 5 |
32-8567631 |
HOSE ASSEMBLY |
| 6 |
32-889314 |
HOSE, Air By-Pass |
| 7 |
32-804829 |
HOSE ASSEMBLY, Air Balance |
| 8 |
32-8M0116380 |
HOSE/SLEEVE |
| 9 |
22-875271 |
FITTING, 90 Degree - Brass (.125-27) |
| 10 |
32-887630 |
HOSE, Molded |
▶Bottom Cowl (26 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
100-8M0107324 |
BOTTOM COWL, Port |
| 2 |
854367001 |
PLUG |
| 3 |
100-8M0107323 |
BOTTOM COWL, Starboard |
| 4 |
27-889246A97 |
GASKET KIT |
| 5 |
10-82130040 |
SCREW, (M6 x 40) |
| 6 |
10-824868 |
SCREW, (M6 x 75) |
| 7 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 8 |
8M0053903 |
FRONT HANDLE |
| 9 |
23-335891 |
BUSHING |
| 10 |
25-48462 |
O-RING, (.614 x .070) |
| 11 |
8219423 |
PAWL |
| 12 |
12-69057 |
WASHER, (.281 x .734 x .063) |
| 13 |
11-401366 |
NUT, (M6) Stainless Steel |
| 14 |
10-8214281 |
SCREW, (#10-16 x .625) |
| 15 |
54-822873 |
CLIP |
| 16 |
87-8M0235191 |
SWITCH, Trim |
| 17 |
32-842756T01 |
RIGGING KIT |
| 18 |
842744002 |
BRACKET |
| 19 |
10-82130012 |
SCREW, (M6 x 12) |
| 20 |
843185T02 |
COUPLER |
| 21 |
32-842756005 |
HOSE |
| 22 |
843174002 |
COUPLER |
| 23 |
10-47994 |
SCREW, (#10 x 1.50) |
| 24 |
852361T02 |
HANDLE Comment: SN# 1B447000 & Up |
| 25 |
13-29402 |
WAVE WASHER Comment: SN# 1B446999 & Below |
| 26 |
8M0109222 |
SEAL |
▶Coil Plate (25 parts)
| Ref |
OEM Part # |
Part Name |
| - |
NSS |
NOT SOLD SEPARATE, Coil Mounting Plate Assembly-Complete |
| 1 |
884272T |
PLATE, Coil Mounting |
| 2 |
300-8M0077471 |
COIL KIT |
| 3 |
10-82129130 |
SCREW, (M6 x 30) |
| 4 |
84-881908T |
CABLE SET |
| 5 |
84-858414A1 |
CABLE ASSEMBLY, Braided |
| 6 |
10-82129110 |
SCREW, (M6 x 10) |
| 7 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 8 |
25-833155 |
GROMMET |
| 9 |
23-8502341 |
BUSHING |
| 10 |
881879T26 |
SENSOR ASSEMBLY, Pressure |
| 11 |
22-8M0207782 |
FITTING |
| 12 |
54-883066 |
CLIP, (.865) |
| 13 |
32-85978571 |
TUBING, (52.00 Inches Bulk) (Cut to 18 Inches) |
| 14 |
84-892972T04 |
HARNESS ASSEMBLY, Coil |
| 15 |
54-879962 |
CLIP |
| 16 |
10-81893435 |
SCREW, (M8 x 35) |
| 17 |
12-4002318 |
WASHER |
| 18 |
22-881866 |
FITTING |
| 19 |
22-875207 |
TEE, Fitting |
| 20 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 21 |
54-8M0024808 |
J CLIP |
| 22 |
33-843220Q |
SPARK PLUG |
| 23 |
32-85978571 |
TUBING, (52.00 Inches Bulk) (Cut to 5 Inches) |
| 24 |
32-85944975 |
TUBING, (72.00 Inches Bulk) (Cut to 52 Inches) |
▶Crankshaft, Pistons and Connecting Rods (21 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-841017A52 |
POWERHEAD ASSEMBLY |
| 1 |
482-842753A02 |
CRANKSHAFT ASSEMBLY |
| 2 |
830882 |
WEAR SLEEVE |
| 3 |
30-67923T |
BEARING, Ball (Lower) |
| 4 |
53-67446 |
RING |
| 5 |
39-843198T01 |
RING, Seal |
| 6 |
28-91800 |
KEY, Woodruff |
| 7 |
25-35126 |
O-RING, (.859 x .139) |
| 8 |
31-88270A02 |
BEARING/RACE KIT |
| 9 |
31-88269T |
BEARING ASSEMBLY |
| 10 |
2720-842986T03 |
PISTON ASSEMBLY Comment: (Port) |
| 11 |
40-841202 |
RING |
| 12 |
39-858772A02 |
RING SET, Piston |
| 13 |
8M8023292 |
CYLINDER |
| 14 |
10-94320 |
SCREW, (.375-24 x 1.250) |
| 15 |
31-844338A01 |
BEARING ASSEMBLY |
| 16 |
12-88263 |
THRUST WASHER |
| 17 |
29-8M0204715 |
BEARING, Needle |
| 18 |
31-816773A2 |
BEARING ASSEMBLY (Upper) |
| 19 |
26-859093 |
SEAL |
| 20 |
25-823683 |
O-RING, (1.989 x .070) |
▶Cylinder Block and End Cap (47 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-841220A03 |
GASKET SET, Powerhead |
| 1 |
885-9811T72 |
CYLINDER BLOCK ASSEMBLY |
| 2 |
10-81893440 |
SCREW, (M8 x 40) |
| 3 |
8M0111325 |
BRACKET |
| 4 |
16-903509 |
STUD, (M10 x 1.5 x 64) |
| 5 |
16-8154431 |
STUD, (M10 x 1.5 x 155) |
| 6 |
17-63779 |
PIN, Dowel (.250 x .625) |
| 7 |
21-8781051 |
CHECK VALVE |
| 8 |
17-8M0036405 |
PIN |
| 9 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) |
| 10 |
22-8245021 |
CONNECTOR |
| 11 |
10-81893435 |
SCREW, (M8 x 35) |
| 12 |
10-82446180 |
SCREW, (M10 x 80) |
| 13 |
8248577 |
DEFLECTOR |
| 14 |
10-82494810 |
SCREW, (M6 x 10) |
| 15 |
12-8M0214963 |
WASHER, (.406 x .750 x .105) Stainless Steel |
| 16 |
11-4013610 |
NUT, (M10) Stainless Steel |
| 17 |
8M0082988 |
SENSOR |
| 18 |
10-40011107 |
SCREW, (M5 x 16) Stainless Steel |
| 19 |
1171-9787A4 |
END CAP ASSEMBLY |
| 20 |
25-62700 |
O-RING, (3.237 x .103) |
| 21 |
26-8308981 |
SEAL |
| 22 |
10-82130020 |
SCREW, (M6 x 20) |
| 23 |
10-82130012 |
SCREW, (M6 x 12) |
| 24 |
23-421581 |
BUSHING |
| 25 |
8215832 |
PIN, Special (1.5 Inches) |
| 26 |
900-841020A08 |
CYLINDER HEAD ASSEMBLY, Port |
| 27 |
818574 |
SEAL |
| 28 |
884391 |
SEAL |
| 29 |
10-8M0045380 |
SCREW, (M8 x 50) |
| 30 |
8M0057307 |
THERMOSTAT, 54 Degree C/130 Degree F |
| 31 |
27-8503181 |
GASKET |
| 32 |
887602002 |
COVER, Thermostat Comment: (Starboard) |
| 33 |
10-82130025 |
SCREW, (M6 x 25) |
| 34 |
22-328022 |
PLUG, Pipe (.125-27) Brass |
| 35 |
8M0148668 |
SENSOR ASSEMBLY |
| 36 |
25-896699 |
O-RING, (1.78 mm x .08 mm) |
| 37 |
857186T02 |
PLATE ASSEMBLY |
| 38 |
23-855729 |
MOUNT |
| 39 |
10-82130145 |
SCREW, (M10 x 45) |
| 40 |
25-19565002 |
GROMMET |
| 41 |
12-855725 |
WASHER |
| 42 |
54-8M0024808 |
J CLIP |
| 43 |
54-858424 |
CLAMP |
| 44 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 45 |
10-82130016 |
SCREW, (M6 x 16) |
| 46 |
54-858951 |
J CLIP |
▶Drivehshaft Housing and Exhaust Tube (28 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
3519-832938A06 |
HOUSING ASSEMBLY, Driveshaft Comment: (X-Long) |
| 2 |
16-8M0008031 |
STUD, (M12 x 52) |
| 3 |
10-892860 |
SCREW, (M12 x 35) |
| 4 |
25-8331231 |
GROMMET |
| 5 |
12-856982 |
WASHER, (.500 x .810 x .090) Stainless Steel |
| 6 |
11-896895 |
NUT, (M12) |
| 7 |
19-64649 |
PLUG |
| 8 |
10-898834 |
BOLT, (M14 x 178) |
| 9 |
88238A10 |
CABLE ASSEMBLY, Ground |
| 10 |
12-815432 |
WASHER, (.562 x 2.00 x .125) |
| 11 |
8M0050840 |
MOUNT (Lower) Comment: (X-Long) |
| 12 |
12-825190 |
WASHER |
| 13 |
11-896602 |
NUT, (M14) |
| 14 |
8186442 |
CLAMP |
| 15 |
10-8M0084475 |
SCREW, (M8 x 40) |
| 16 |
12-847541 |
WASHER |
| 17 |
8M0001136 |
COVER, Lower Mount |
| 18 |
10-69079 |
SCREW, (#10-16 x .440) |
| 19 |
8329321 |
SEAL |
| 20 |
833116A19 |
TUBE ASSEMBLY, Exhaust |
| 21 |
35-8M0026113 |
STRAINER |
| 22 |
10-81893435 |
SCREW, (M8 x 35) |
| 23 |
32-8M0042786 |
TUBE, Water Comment: (X-Long) |
| 24 |
832940001 |
SEAL |
| 25 |
8329391 |
CLAMP |
| 26 |
10-41508 |
SCREW, (.250-20 x .500) Stainless Steel |
| 27 |
10-81893435 |
SCREW, (M8 x 35) |
| 28 |
13-72521 |
LOCKWASHER, Internal Tooth |
▶Electrical Plate Components (28 parts)
| Ref |
OEM Part # |
Part Name |
| - |
879346A41 |
HARNESS ASSEMBLY, Throttle Position Sensor |
| 1 |
899071T01 |
PLATE |
| 2 |
54-899145 |
CLIP, Tie Strap |
| 3 |
10-82129114 |
SCREW, (M6 x 14) |
| 4 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 5 |
8M0207773 |
RELAY ASSEMBLY |
| 6 |
828102 |
BRACKET |
| 7 |
25-818967 |
GROMMET |
| 8 |
23-8M0214955 |
BUSHING |
| 9 |
10-82129125 |
SCREW, (M6 x 25 MM) |
| 10 |
84-892971T05 |
HARNESS ASSEMBLY, Engine |
| 11 |
85-875302A1 |
HOT STUD ASSEMBLY |
| 12 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 13 |
12-85172 |
WASHER |
| 14 |
84-93388T21 |
CABLE ASSEMBLY, Black |
| 15 |
84-93388A17 |
CABLE ASSEMBLY, (8.50 Inches) |
| 16 |
84-878231A6 |
HARNESS ASSEMBLY, Fuse - 100 Ampere |
| 17 |
13-53166 |
LOCKWASHER, (.312) |
| 18 |
11-400213 |
NUT, (M8) Stainless Steel |
| 19 |
84-88439A46 |
CABLE ASSEMBLY, Battery - Positive |
| 20 |
89-817109A2 |
SOLENOID ASSEMBLY, (#10-32 / .3125-18 Terminals) |
| 21 |
25-822179 |
GROMMET |
| 22 |
23-8M0214955 |
BUSHING |
| 23 |
84-88807A16 |
CABLE ASSEMBLY, (4.00 Inches) Black |
| 24 |
10-32,11-45076 |
NUT, Brass |
| 25 |
10-32,11-813938 |
CAP NUT, |
| 26 |
11-8M0204668 |
NUT, (.312-18) |
| 27 |
84-819514T26 |
HARNESS ASSEMBLY, Trim |
▶Exhaust Plate (38 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-841220A03 |
GASKET SET, Powerhead |
| 1 |
832935A17 |
PLATE ASSEMBLY, Exhaust |
| 2 |
27-832933006 |
GASKET |
| 3 |
27-832934006 |
GASKET (Lower) |
| 4 |
8M0043157 |
SEAL |
| 5 |
22-8320761 |
FITTING, Check Valve |
| 6 |
25-30641 |
O-RING, (.299 x .103) |
| 7 |
8219631 |
CHECK VALVE |
| 8 |
21-817519A1 |
CHECK VALVE ASSEMBLY, Drain |
| 9 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) |
| 10 |
22-887603 |
FITTING |
| 11 |
65663A2 |
COVER ASSEMBLY (Includes Reference #18) |
| 12 |
10-81893435 |
SCREW, (M8 x 35) |
| 13 |
814190 |
CARRIER |
| 14 |
25-814191 |
GROMMET |
| 15 |
814189 |
POPPET |
| 16 |
24-64878 |
SPRING, (Black) |
| 17 |
65664A1 |
PLATE ASSEMBLY |
| 18 |
27-88907003 |
GASKET |
| 19 |
648771 |
DIAPHRAGM |
| 20 |
12-76451 |
WASHER |
| 21 |
10-69570 |
SCREW, (#10-16 x .750) |
| 22 |
43585 |
COUPLING |
| 23 |
25-822002 |
GROMMET |
| 24 |
22-94848 |
FITTING |
| 25 |
10-81893435 |
SCREW, (M8 x 35) |
| 26 |
850306A04 |
BOOT KIT, Idle Exhaust |
| 27 |
888910 |
PLATE |
| 28 |
10-82239312 |
SCREW, (M5 x 12) |
| 29 |
19-821908 |
PLUG |
| 30 |
12-821915 |
WASHER |
| 31 |
32-859626A1 |
FLUSH HOSE KIT (Inlet) |
| 32 |
22-8596001 |
FITTING |
| 33 |
54-850896 |
CLAMP, (28.6) |
| 34 |
22-8M0077650 |
FITTING, Tell-Tale |
| 35 |
35-8348084 |
STRAINER |
| 36 |
23-48237 |
BUSHING |
| 37 |
25-12602002 |
GROMMET |
▶Flywheel/Alternator (19 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
8M6013461 |
ALTERNATOR |
| 2 |
24-8523742 |
SPRING |
| 3 |
11-400636 |
NUT |
| 4 |
856815T2 |
ARM TENSIONER ASSEMBLY |
| 5 |
12-4002320 |
WASHER |
| 6 |
16-8M0063255 |
STUD, M10x92 Comment: ProXS |
| 7 |
23-8568941 |
BUSHING |
| 8 |
8M6005030 |
PULLEY ASSEMBLY |
| 9 |
10-4010835 |
SCREW, (M10 x 35) Hex Flange - Stainless Steel |
| 10 |
57-828507Q5 |
BELT |
| 11 |
283-859619T1 |
FLYWHEEL |
| 12 |
11-42979 |
NUT, (M16) |
| 13 |
12-33001 |
WASHER, (.641 x 1.250 x .190) |
| 14 |
12-47533 |
WASHER, Thermostat |
| 15 |
11-401386 |
NUT, (M6) Stainless Steel |
| 16 |
84-856583A5 |
CABLE ASSEMBLY, To Block |
| 17 |
12-4002319 |
WASHER |
| 18 |
10-82130150 |
SCREW, (M10 x 50) |
| 19 |
19-45907 |
PLUG, Yellow |
▶Fuel Pump (23 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-841220A03 |
GASKET SET, Powerhead |
| 1 |
NSS |
NOT SOLD SEPARATE, Fuel Pump |
| 2 |
21-857005A1 |
DIAPHRAGM KIT |
| 3 |
NSS |
NOT SOLD SEPARATE, Diaphragm |
| 4 |
NSS |
NOT SOLD SEPARATE, Retainer |
| 5 |
NSS |
NOT SOLD SEPARATE, Spring |
| 6 |
NSS |
NOT SOLD SEPARATE, Cap |
| 7 |
NSS |
NOT SOLD SEPARATE, Spring |
| 8 |
NSS |
NOT SOLD SEPARATE, Cap |
| 9 |
NSS |
NOT SOLD SEPARATE, Diaphragm |
| 10 |
NSS |
NOT SOLD SEPARATE, Gasket-Boost |
| 11 |
NSS |
NOT SOLD SEPARATE, Gasket-Pulse |
| 12 |
25-8M0204683 |
O-RING, (.301 x .070) |
| 13 |
987752 |
PLATE |
| 14 |
22-996642 |
FITTING, Elbow 90 Degree (.125-27 x .250) Nylon |
| 15 |
10-82104540 |
SCREW, (M5 x 40), Fuel Pump |
| 16 |
10-82130050 |
SCREW, (M6 x 50), Pump to Crankcase |
| 17 |
144303 |
BASE |
| 18 |
22-782792 |
FITTING, Elbow 45 Degree (1.25) |
| 19 |
22-888493 |
ELBOW |
| 20 |
22-822769 |
CONNECTOR |
| 21 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 22 |
32-8M0043979 |
HOSE AND SLEEVE ASSEMBLY, (18.00 Inches) |
▶Fuel System (39 parts)
| Ref |
OEM Part # |
Part Name |
| - |
8M0185156 |
FUEL RAIL ASSEMBLY, Complete |
| NS |
25-804840 |
O-RING KIT |
| 1 |
NSS |
NOT SOLD SEPARATE, Fuel Rail (Port) |
| 2 |
NSS |
NOT SOLD SEPARATE, Fuel Rail (Starboard) |
| 3 |
54-804830 |
CLAMP |
| 4 |
10-804525001 |
SCREW PACKAGE, (2 Per)(M5 x 10) |
| 5 |
8M0047053 |
VALVE ASSEMBLY, (.375 Inch Diameter) |
| 6 |
25-804840 |
O-RING KIT |
| 7 |
22-805515 |
CAP, Shrader Valve - Brass |
| 8 |
19-804835 |
PLUG |
| 9 |
8M0041097 |
CLAMP |
| 10 |
54-8048311 |
CLAMP |
| 11 |
8M0222157 |
INJECTOR |
| 12 |
25-804530 |
O-RING KIT |
| 13 |
25-804529 |
O-RING KIT |
| 14 |
804522 |
CLAMP |
| 15 |
804532 |
O-RING KIT (16 per Kit |
| 16 |
54-804832 |
CLAMP |
| 17 |
804526 |
SCREW PACKAGE, (M5 x 16) (2 Per) |
| 18 |
804535001 |
COVER |
| 19 |
24-804534001 |
SPRING |
| 20 |
804533 |
DIAPHRAGM ASSEMBLY |
| 21 |
25-804536 |
O-RING |
| 22 |
22-804836 |
FITTING |
| 23 |
32-804827 |
HOSE |
| 24 |
32-889310 |
HOSE, Fuel Supply |
| 25 |
32-889311 |
HOSE, Fuel By Pass |
| 26 |
26-888852 |
SEAL, Fuel Director |
| 27 |
8M6001744 |
INJECTOR ASSEMBLY, Air |
| 28 |
26-804875 |
SEAL KIT |
| 29 |
12-859404002 |
WASHER, Injection |
| 30 |
828791 |
CLIP |
| 31 |
16-8M0063255 |
STUD, (M10 x 91) |
| 32 |
11-826292 |
NUT, (M10) Brass/Nickel Plated |
| 33 |
54-8M0214964 |
CLAMP, Hose (15.3) |
| 34 |
32-8M0043979 |
HOSE AND SLEEVE ASSEMBLY, (18.00 Inches) |
| 35 |
22-822769 |
CONNECTOR |
| 36 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 37 |
54-899145 |
CLIP, Tie Strap |
▶Gear Housing(Driveshaft - TorqueMaster) (47 parts)
| Ref |
OEM Part # |
Part Name |
| - |
26-816575A6 |
SEAL KIT, Gear Housing |
| 1 |
1689-842739T16 |
GEAR HOUSING ASSEMBLY, Basic (Black) Comment: SN# 1B465109 & Up |
| 2 |
17-379721 |
PIN |
| 3 |
821526001 |
FILLER BLOCK |
| 4 |
97-826134Q |
ANODE |
| 5 |
10-4000333 |
SCREW, (M6 x 40) |
| 6 |
11-401386 |
NUT, (M6) Stainless Steel |
| 7 |
31-42647A1 |
BEARING ASSEMBLY, Roller |
| 8 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) |
| 9 |
10-79953Q04 |
SCREW KIT, Drain |
| 10 |
26-8M0204693 |
SEAL |
| 11 |
859402 |
PITOT TUBE |
| 12 |
26-8M0204708 |
SEAL, Oil |
| 13 |
22-881866 |
FITTING |
| 14 |
858934 |
COVER |
| 15 |
27-858935 |
GASKET |
| 16 |
25-896522 |
O-RING, (799 x .103) Comment: SN# 1B465109 & Up |
| 17 |
10-1993716 |
SCREW, (M6 x 16) Comment: SN# 1B465109 & Up |
| 18 |
10-1993716 |
SCREW, (M6 x 16) Comment: SN# 1B465109 & Up |
| 19 |
NSS |
NOT SOLD SEPARATE, Pinion Gear Comment: (Part of Forward Gear Kit) |
| 20 |
12-92721 |
WASHER |
| 21 |
11-35921 |
NUT, (.625-18) |
| 22 |
12-77674 |
WASHER |
| 23 |
824145 |
SHIFT SHAFT |
| 24 |
28-8M0204723 |
KEY |
| 25 |
45-881942 |
DRIVESHAFT Comment: (X-Long) |
| 26 |
15-8M0063268 |
SHIM ASSEMBLY |
| 27 |
31-8M0146553 |
BEARING, Tapered Roller |
| 28 |
NSS |
NOT SOLD SEPARATE, Cup |
| 29 |
15-42637A1 |
SHIM SET |
| 30 |
31-8M0146566 |
BEARING ASSEMBLY, Roller/Cup |
| 31 |
NSS |
NOT SOLD SEPARATE, Cup |
| 32 |
8245191 |
RETAINER |
| 33 |
8M0192207 |
CARRIER ASSEMBLY |
| 34 |
25-8M0142854 |
O-RING, (2.175 x .175) |
| 35 |
26-8M0214939 |
SEAL, Oil |
| 36 |
26-8M0214939 |
SEAL, Oil |
| 37 |
10-1993716 |
SCREW, (M6 x 16) Comment: SN# 1B465109 & Up |
| 38 |
817275A1 |
HOUSING KIT, Water Pump |
| 39 |
26-816575A2 |
SEAL KIT |
| 40 |
27-430331 |
GASKET |
| 41 |
27-8172771 |
GASKET |
| 42 |
8M0204709 |
FACEPLATE |
| 43 |
47-43026T2 |
IMPELLER |
| 44 |
832942A1 |
COUPLING ASSEMBLY |
| 45 |
25-8M0204645 |
O-RING, (.796 x .139) |
| 46 |
25-8M0204654 |
O-RING, (1.046) |
▶Gear Housing, Propeller Shaft - TorqueMaster (35 parts)
| Ref |
OEM Part # |
Part Name |
| - |
26-816575A6 |
SEAL KIT, Gear Housing |
| 1 |
1689-842739T16 |
GEAR HOUSING ASSEMBLY, Basic (Black) Comment: SN# 1B465109 & Up |
| 2 |
22-859403 |
PLUG |
| 3 |
8M0226861 |
SHIFT CRANK |
| 4 |
8M0235940 |
SPOOL ASSEMBLY |
| 5 |
NSS |
NOT SOLD SEPARATE, Spool |
| 6 |
NSS |
NOT SOLD SEPARATE, Sleeve |
| 7 |
NSS |
NOT SOLD SEPARATE, Cotter Pin |
| 8 |
15-47397A1 |
SHIM SET |
| 9 |
43-859321T04 |
GEAR SET, Forward/Pinion |
| 10 |
31-828437A2 |
BEARING ASSEMBLY |
| 11 |
NSS |
NOT SOLD SEPARATE, Cup |
| 12 |
31-30895T |
BEARING, Needle |
| 13 |
53-856823 |
RING, Retaining |
| 14 |
52-848878T |
CLUTCH |
| 15 |
17-78909 |
PIN, Detent |
| 16 |
17-848838 |
PIN, Cross |
| 17 |
24-78962 |
SPRING |
| 18 |
44-841978 |
PROPELLER SHAFT |
| 19 |
43-8M0192235 |
GEAR, Reverse |
| 20 |
23-8241081 |
THRUST SPACER |
| 21 |
30-88957T |
BEARING, Ball |
| 22 |
681001 |
RING, Thrust |
| 23 |
25-8M0142840 |
O-RING, (3.850 x .210) Comment: SN# 1B465109 & Up |
| 24 |
848840A1 |
CARRIER ASSEMBLY, Bearing |
| 25 |
31-817072 |
BEARING, Roller |
| 26 |
53-817071 |
RING, Snap |
| 27 |
26-815565 |
SEAL, Oil |
| 28 |
28-30281 |
KEY |
| 29 |
10-79953Q04 |
SCREW KIT, Drain Comment: SN# 1B465109 & Up |
| 30 |
26-8M0204693 |
SEAL |
| 31 |
14-79447 |
TAB WASHER |
| 32 |
8M2011027 |
RETAINER |
| 33 |
97-76214Q5 |
ANODE |
| 34 |
10-66024 |
SCREW, (.437-14 x 1.75) |
▶Oiling System (37 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 11.50 Inches) |
| 2 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 5 Inches) |
| 3 |
35-8M0207786 |
FILTER, Fuel |
| 4 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 9 Inches) |
| 5 |
1200-8M0064075 |
TANK, Oil |
| 6 |
NSS |
NOT SOLD SEPARATE, Decal-Reservoir |
| 7 |
25-855362001 |
GROMMET |
| 8 |
23-855364 |
BUSHING |
| 9 |
23-883050 |
SPACER |
| 10 |
10-58376 |
SCREW, (.164-18 x .375) |
| 11 |
12-72761 |
WASHER, (.203 x .562 x .060) Stainless Steel |
| 12 |
87-856156T04 |
SWITCH |
| 13 |
32-885553 |
HOSE |
| 14 |
22-8M0207780 |
FITTING |
| 15 |
19-887609 |
PLUG |
| 16 |
12-4002318 |
WASHER |
| 17 |
10-81893435 |
SCREW, (M8 x 35) |
| 18 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 19 |
32-8752891 |
HOSE |
| 20 |
22-858955 |
CONNECTOR |
| 21 |
32-875283 |
HOSE, (2.00 Inches) |
| 22 |
35-875284T01 |
FILTER, Oil - In Line |
| 23 |
NSS |
NOT SOLD SEPARATE, Plug |
| 24 |
32-892830053 |
HOSE, (24.00 Inches Braided) (Cut to 22 Inches) |
| 25 |
10-81893460 |
SCREW, (M8 x 60) |
| 26 |
21-858870 |
CHECK VALVE |
| 27 |
859230T |
RETAINER |
| 28 |
32-8M0054213 |
HOSE, (40.00 Inches Bulk) (Cut to 34 Inches) |
| 29 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 19.50 Inches) |
| 30 |
56762 |
TIE STRAP, (4.00 Inches) |
| 31 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 11 Inches) |
| 32 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 6 Inches) |
| 33 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 4 Inches) |
| 34 |
22-883988 |
ELBOW |
| 35 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 22 Inches) |
| 36 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 16.50 Inches) |
| 37 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 7 Inches) |
▶PCM Mounting (15 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
89790649T |
PCM, Propulsion Control Module |
| 2 |
10-82130025 |
SCREW, (M6 x 25) |
| 3 |
12-65567 |
WASHER, (.265 x .750 x .048) Stainless Steel |
| 4 |
25-8M0190980 |
GROMMET |
| 5 |
23-856954 |
BUSHING |
| 6 |
54-891520001 |
CLIP |
| 7 |
10-82129114 |
SCREW, (M6 x 14) |
| 8 |
10-82130012 |
SCREW, (M6 x 12) |
| 9 |
13541 |
PLUG, Male |
| 10 |
84-88439A26 |
CABLE ASSEMBLY, Battery - Negative |
| 11 |
10-81893420 |
SCREW, (M8 x 20) |
| 12 |
830796A04 |
CONNECTOR ASSEMBLY, Weather Cap - Male |
| 13 |
877613A02 |
CONNECTOR ASSEMBLY, Weather Cap 6 Pin |
| 14 |
881176A1 |
CAP ASSEMBLY, 3 Position-Male Connector |
| 15 |
54-816311T |
TIE STRAP, (8.00 Inches) |
▶Port Center Main Oiling System (13 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-841017A52 |
POWERHEAD ASSEMBLY |
| 1 |
22-887801 |
FITTING, Elbow 90 Degree (.0625-27) |
| 2 |
22-887801 |
FITTING, Elbow 90 Degree (.0625-27) |
| 3 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 20.50 Inches) |
| 4 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 5 Inches) |
| 5 |
21-8592352 |
CHECK VALVE, 90 Degree (.0625-27) |
| 6 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 13 Inches) |
| 7 |
21-8282182 |
CHECK VALVE |
| 8 |
21-8582362 |
CHECK VALVE |
| 9 |
54-23567 |
CLIP |
| 10 |
10-878608 |
SCREW, (#10-16 x .500) |
| 11 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 11 Inches) |
| 12 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 9.50 Inches) |
▶Power Trim Components (38 parts)
| Ref |
OEM Part # |
Part Name |
| - |
25-878285 |
O-RING |
| 1 |
878265A4 |
TRIM MOTOR |
| 2 |
NSS |
NOT SOLD SEPARATE, Armature |
| 3 |
NSS |
NOT SOLD SEPARATE, End Frame |
| 4 |
10-82494830 |
SCREW, (M6 x 30) |
| 5 |
13-400256 |
LOCKWASHER, (M6) |
| 6 |
8782451 |
DRIVESHAFT |
| 7 |
878410A1 |
PO CHECK KIT |
| 8 |
893929A01 |
MANUAL RELEASE ASSEMBLY (Includes Reference #26) |
| 9 |
8M0142997 |
SHAFT KIT |
| 10 |
17-878267 |
PIN |
| 11 |
878235A03 |
TILT CYLINDER ASSEMBLY |
| 12 |
878239A02 |
GUIDE KIT (Includes Reference #26) |
| 13 |
8M0142999 |
O-RING KIT (Includes Reference #26) |
| 14 |
8M0168219 |
SHOCK ROD KIT (Includes Reference #26) |
| 15 |
8M0143000 |
PISTON ASSEMBLY, Memory |
| 16 |
878406A02 |
REPAIR KIT, Check Valve (Includes Reference #26) |
| 17 |
878414T01 |
PISTON ASSEMBLY |
| 18 |
878413A1 |
PISTON ASSEMBLY |
| 19 |
1100-8M0021648 |
GUIDE ASSEMBLY |
| 20 |
878264A1 |
RESERVOIR KIT |
| 21 |
19-811613 |
PLUG ASSEMBLY |
| 22 |
10-4000327 |
SCREW, (M6 x 14) |
| 23 |
12-4002315 |
WASHER |
| 24 |
892251A01 |
PUMP KIT |
| 25 |
878408A1 |
REPAIR KIT, Power Trim |
| 26 |
17-821539 |
PIN, Trilobe |
| 27 |
10-858771 |
SCREW, (M10 x 30) |
| 28 |
12-4002319 |
WASHER |
| 29 |
97-818298Q1 |
ANODE KIT |
| 30 |
10-8M0204707 |
SCREW, (M6 x 25) |
| 31 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 32 |
99625002 |
SHAFT |
| 33 |
8M0084613 |
C WASHER |
| 34 |
54-26550 |
CLAMP |
| 35 |
10-878609 |
SCREW, (#10-16 x .600) |
| 36 |
32-828547353 |
CONDUIT, (.350 Inside Diameter x 3.00 Feet Bulk) (Cut to 12 Inches) |
| 37 |
54-816311T |
TIE STRAP, (8.00 Inches) |
▶Powerhead Gasket Set Components (1 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-88907003 |
GASKET, Relief Valve Cover and Plate |
▶Service/Support Material (1 parts)
| Ref |
OEM Part # |
Part Name |
| - |
37-898246A08 |
DECAL, EPA Label Information Comment: (2008) |
▶Starboard Center Main Oiling System (8 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-841017A52 |
POWERHEAD ASSEMBLY |
| 1 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 15.50 Inches) |
| 2 |
21-8592352 |
CHECK VALVE, 90 Degree (.0625-27) |
| 3 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 16.50 Inches) |
| 4 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 15 Inches) |
| 5 |
54-23567 |
CLIP |
| 6 |
10-878608 |
SCREW, (#10-16 x .500) |
| 7 |
22-887801 |
FITTING, Elbow 90 Degree (.0625-27) |
▶Starter Motor (14 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
50-892339T01 |
STARTER MOTOR ASSEMBLY |
| 2 |
NSS |
NOT SOLD SEPARATE, Thru Bolt |
| 3 |
43-880805A1 |
GEAR KIT |
| 4 |
809463A1 |
SOLENOID KIT |
| 5 |
8M0065258 |
BRUSH SET |
| 6 |
10-69035 |
SCREW AND LOCKWASHER, (.250-20 x .625) Stainless Steel |
| 7 |
84-93388A1 |
CABLE ASSEMBLY, (6.00 Inches) Black |
| 8 |
37-8272822 |
DECAL, Warning |
| 9 |
13-400255 |
LOCKWASHER, (M5) |
| 10 |
11-400211 |
NUT, (M5) Stainless Steel |
| 11 |
13-8M0204647 |
LOCKWASHER, (.312) |
| 12 |
11-400213 |
NUT, (M8) Stainless Steel |
| 13 |
23-8M0034918 |
COLLAR |
| 14 |
8M0043276 |
STOP |
▶Swivel Bracket and Steering Arm (31 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
1499-8M0102865 |
SWIVEL BRACKET ASSEMBLY, Black |
| 2 |
25-8M0214926 |
O-RING |
| 3 |
23-818764 |
BUSHING |
| 4 |
23-816039 |
SPACER |
| 5 |
26-87735 |
SEAL, Oil (Lower) |
| 6 |
22-8M0169589 |
FITTING, Grease |
| 7 |
23-821207 |
BUSHING |
| 8 |
12-816432 |
THRUST WASHER |
| 9 |
826364T |
YOKE, Bottom |
| 10 |
53-67684 |
RING, Retaining |
| 11 |
8M0045383 |
STRIKER PLATE |
| 12 |
13-58643 |
LOCKWASHER, (.375) |
| 13 |
11-46335 |
NUT, (.375-24) |
| 14 |
10-64014 |
SCREW, (.250-28 x .500) |
| 15 |
NSS |
NOT SOLD SEPARATE, Decal-Serial Overlaminate |
| 16 |
8M0074846 |
SENDER ASSEMBLY, Trim |
| 17 |
10-852368 |
SCREW, (#10-24 x .750) |
| 18 |
10,13-26996 |
LOCKWASHER, Stainless Steel |
| 19 |
12-89302 |
WASHER, (.203 x .406 x .040) |
| 20 |
17-8M0132731 |
SWIVEL PIN ASSEMBLY, Steering Arm - Stainless Steel |
| 21 |
10-8M0141069 |
SCREW, (M12 x 190) |
| 22 |
824998001 |
BUMPER |
| 23 |
8M0051214 |
MOUNT, Upper - Blue Stripe Comment: (X-Long) |
| 25 |
12-4002321 |
WASHER, (12.80 mm x 24.0 mm x 2.4 mm) Stainless Steel |
| 26 |
11-896963 |
NUT, (M12) |
| 27 |
8M0036783 |
CLAMP |
| 28 |
10-81893435 |
SCREW, (M8 x 35) |
| 29 |
92876A12 |
LINK ROD ASSEMBLY |
| 30 |
10-849838 |
SCREW, (.375-24 x 1.250) |
| 31 |
11-8M0204726 |
NUT, (.375-24) Stainless Steel |
| 32 |
12-37828 |
WASHER, (.390 x .625 x .062) Stainless Steel |
▶Throttle Linkage (46 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
8M0040987 |
LEVER |
| 2 |
10-81893460 |
SCREW, (M8 x 60) |
| 3 |
23-887605 |
BUSHING |
| 4 |
23-821113 |
BUSHING |
| 5 |
10-40124 |
SCREW, (M6 x 55) |
| 6 |
11-400212 |
NUT, (M6) Stainless Steel |
| 7 |
42942 |
CAP |
| 8 |
42927 |
INSERT |
| 9 |
11-401386 |
NUT, (M6) Stainless Steel |
| 10 |
23-8M0215006 |
BUSHING |
| 11 |
884834 |
LINK |
| 12 |
824010T05 |
BRACKET, Anchor |
| 13 |
824016 |
LATCH |
| 14 |
10-42975 |
DRIVE SCREW |
| 15 |
824015 |
CUP, Barrel Retainer |
| 16 |
10-82155025 |
SCREW, (M8 x 25 MM) Stainless Steel |
| 17 |
12-43430 |
WASHER |
| 18 |
10-82155025 |
SCREW, (M8 x 25 MM) Stainless Steel |
| 19 |
8M0039052 |
BRACKET, Slide |
| 20 |
87-8M0207794 |
SWITCH |
| 21 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 22 |
10-82470620 |
SCREW, (M3.5 x 20) |
| 23 |
12-35459 |
WASHER |
| 24 |
883142A03 |
SHIFT LINK KIT |
| 25 |
8539683 |
SLIDE |
| 26 |
11-401386 |
NUT, (M6) Stainless Steel |
| 27 |
23-42994 |
BUSHING |
| 28 |
8M0187153 |
SHIFT SHAFT, Upper Comment: (X-Long) |
| 29 |
10-40011113 |
SCREW, (M5 x 45) Stainless Steel |
| 30 |
8582261 |
COVER |
| 31 |
8M0008111 |
LINK |
| 32 |
883081 |
LEVER |
| 33 |
8M6005165 |
INDICATOR, Throttle Position |
| 34 |
10-82130025 |
SCREW, (M6 x 25) |
| 35 |
12-65567 |
WASHER, (.265 x .750 x .048) Stainless Steel |
| 36 |
25-8M0190980 |
GROMMET |
| 37 |
23-856954 |
BUSHING |
| 38 |
8544862 |
BRACKET |
| 39 |
54-858932 |
CLIP |
| 40 |
858353T10 |
CAM ASSEMBLY |
| 41 |
8235694 |
BALL, Threaded |
| 42 |
23-8M0215006 |
BUSHING |
| 43 |
10-40011155 |
SCREW, (M8 x 55) Stainless Steel |
| 44 |
23-8807371 |
BUSHING |
| 45 |
12-56720 |
WASHER, (.330 x .750 x .060) Stainless Steel |
| 46 |
54-475451 |
CLIP |
▶Top Cowl (22 parts)
| Ref |
OEM Part # |
Part Name |
| - |
37-8M0061187 |
DECAL, Horsepower 250 |
| 1 |
100-881288T66 |
TOP COWL ASSEMBLY, (Black) (Includes all Decals except HorsePower) Comment: SN# 1B447000 & Up |
| 2 |
10-82130030 |
SCREW, (M6 x 30) |
| 3 |
884041A04 |
SOUND BLANKET KIT |
| 4 |
NSS |
NOT SOLD SEPARATE, Sound Blanket-Top |
| 5 |
NSS |
NOT SOLD SEPARATE, Sound Blanket-Port |
| 6 |
13-93702 |
WASHER, (.250 External Star) |
| 7 |
826639T |
COVER |
| 8 |
8M0010389 |
BRACKET ASSEMBLY, Cowl Comment: SN# 1B447000 & Up |
| 9 |
NSS |
NOT SOLD SEPARATE, Pin |
| 10 |
53-8237951 |
RING, Retaining |
| 11 |
8M0207770 |
ROLLER |
| 12 |
25-850685T02 |
GROMMET |
| 13 |
8M0036792 |
BRACKET, Front |
| 14 |
10-82130020 |
SCREW, (M6 x 20) |
| 15 |
815477 |
BUMPER, Latch |
| 16 |
8155381 |
PIN, Roll |
| 17 |
11-401366 |
NUT, (M6) Stainless Steel |
| 18 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 19 |
53-8237951 |
RING, Retaining |
| 20 |
8M0207770 |
ROLLER |
| 21 |
12-87161 |
WASHER |
▶Transom Brackets (21 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
3426-828334T03 |
BRACKET ASSEMBLY, Transom-Starboard |
| 2 |
3425-828333T08 |
BRACKET ASSEMBLY, Transom-Port |
| 3 |
22-8M0169588 |
FITTING, Grease Comment: (Port) |
| 4 |
826125A1 |
TILT TUBE |
| 5 |
11-826135 |
NUT, (1.00-14) Nylon Insert |
| 6 |
25-45711 |
O-RING, (.612 x .103) |
| 7 |
13-88750 |
WASHER |
| 8 |
11-826164 |
NUT, (.875-14) |
| 9 |
10-8M0149747 |
SCREW, (.500-20 x 4.500) |
| 10 |
12-8M0204665 |
WASHER, (.530 x .870 x .105) Stainless Steel |
| 11 |
12-8M0204648 |
WASHER, (1.5 x 3.05 x 0.13) Stainless Steel |
| 12 |
11-82671117 |
NUT, (.500-20) |
| 13 |
8M0115104 |
LEVER ASSEMBLY, Tilt Lock |
| 14 |
24-830899 |
SPRING, Tension |
| 15 |
23-65830 |
NYLINER |
| 16 |
24-830900 |
SPRING, Compression |
| 17 |
99633 |
KNOB |
| 18 |
17-99615 |
PIN, Groove |
| 19 |
17-893709 |
PIN |
| 20 |
10-96930A1 |
BOLT ASSEMBLY |
| 21 |
11-23161 |
NUT, (.375-24) |
▶Vapor Separator Components (42 parts)
| Ref |
OEM Part # |
Part Name |
| - |
25-889316A1 |
O-RING KIT, Vapor Seperator |
| 1 |
889317T1 |
COVER KIT |
| 2 |
NSS |
NOT SOLD SEPARATE, Seat |
| 3 |
889318001 |
PLATE, Baffle |
| 4 |
10-883223 |
SCREW, (M6 x 16) |
| 5 |
27-889319 |
GASKET |
| 6 |
22-883556 |
FITTING |
| 7 |
25-8M0062785 |
O-RING |
| 8 |
22-14868 |
FITTING |
| 9 |
19-883208 |
PLUG |
| 10 |
35-8M0122423 |
FILTER, Fuel |
| 11 |
889320A1 |
FLOAT KIT |
| 12 |
F10064 |
SHAFT |
| 13 |
888725T02 |
PUMP ASSEMBLY, Fuel - High Pressure |
| 14 |
8M6000589 |
SLEEVE |
| 15 |
25-8893162 |
O-RING |
| 16 |
26-889321 |
SEAL |
| 17 |
889328 |
RETAINER |
| 18 |
1395-9643 |
SCREW |
| 19 |
888733T02 |
PUMP ASSEMBLY, Boost |
| 20 |
25-889322 |
GROMMET |
| 21 |
25-889316 |
O-RING |
| 22 |
26-8M6001413 |
SEAL |
| 23 |
889324T03 |
BOWL KIT |
| 24 |
84-889325A02 |
WIRE |
| 25 |
NSS |
NOT SOLD SEPARATE, Check Valve |
| 26 |
22-855424011 |
FITTING |
| 27 |
889326A1 |
VALVE KIT, Inlet |
| 28 |
10-889327002 |
SCREW, Drain |
| 29 |
32-883545002 |
HOSE |
| 30 |
8M0214989 |
SENSOR, Water |
| 31 |
22-782792 |
FITTING, Elbow 45 Degree (1.25) |
| 32 |
25-627021 |
O-RING, (.301 x .070) |
| 33 |
889430 |
INSERT |
| 34 |
884820 |
SHRADER VALVE |
| 35 |
25-891778 |
O-RING |
| 36 |
54-884819 |
CLIP |
| 37 |
10-40011126 |
SCREW, (M6 x 13) Stainless Steel |
| 38 |
25-855362001 |
GROMMET |
| 39 |
23-883050 |
SPACER |
| 40 |
10-81893460 |
SCREW, (M8 x 60) |
| 41 |
12-4002318 |
WASHER |
▶Water Hoses (12 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-841017A52 |
POWERHEAD ASSEMBLY |
| 1 |
22-858855 |
FITTING, Straight |
| 2 |
54-855228 |
CLAMP, (25.6 mm) |
| 3 |
32-859090001 |
HOSE, Starboard Dump |
| 4 |
32-859089001 |
HOSE, Port Dump |
| 5 |
32-856839 |
TUBING |
| 6 |
54-815504104 |
CLAMP, Worm Gear |
| 7 |
32-774572 |
HOSE, (48.00 Inches Bulk) (Cut to 21 Inches) |
| 8 |
54-815504104 |
CLAMP, Worm Gear |
| 9 |
54-815504104 |
CLAMP, Worm Gear |
| 10 |
22-291112 |
FITTING |
| 11 |
22-996642 |
FITTING, Elbow 90 Degree (.125-27 x .250) Nylon |
100-Hour / Annual Service Checklist
Regular maintenance keeps your Mercury 250 PRO XS (3.0L DFI) running reliably season after season. Most of these tasks can be performed with basic tools and the factory service manual.
- Replace water pump impeller and inspect wear plate
- Change engine oil and oil filter (check drain plug washer)
- Replace spark plugs and check ignition timing
- Drain and refill lower unit gear oil; inspect for water contamination
- Inspect fuel lines, primer bulb, and fuel filter for deterioration
- Check and replace sacrificial anodes (zinc or aluminum)
- Inspect propeller for damage; check shaft seal and cotter pin
- Check valve clearance (refer to service manual for specifications)
- Lubricate all grease points (steering, tilt tube, shift linkage)
- Inspect control cables and throttle/shift linkage for smooth operation
-
Pro Tip: Always flush the engine with fresh water after saltwater use — even a quick 10-minute flush significantly extends component life.
-
Pro Tip: Use fuel stabilizer in the tank before winter storage, and fog the cylinders to prevent internal corrosion during extended periods of non-use.