🔎 Mercury 115 EFI (4-STROKE) Reference Library — Exploded parts diagrams (52 diagrams), specifications, common issues, and maintenance checklist.
The Mercury 115 EFI (4-STROKE) is a 4-Stroke, Inline 4-Cylinder, SOHC, 8-valve outboard motor. Powers center-console boats, larger pontoons, and offshore-capable fishing craft.
Quick Reference Specifications
| Specification |
Value |
| Engine Type |
4-Stroke, Inline 4-Cylinder, SOHC, 8-valve |
| Horsepower |
115 HP |
| Displacement |
2100 cc (2.1L) |
| Bore x Stroke |
90 mm x 81 mm |
| Spark Plug (Type & Gap) |
NGK SILZKR7B11 |
| Engine Oil Capacity |
5.0 L (5.28 qt) |
| Recommended Engine Oil |
Mercury FourStroke Oil 10W-30 |
| Gear Case Oil Capacity |
24 fl oz (710 mL) |
| Idle Speed (in gear) |
650 ± 50 RPM (in gear) |
| Full Throttle RPM Range |
5000-6000 |
| Fuel |
Unleaded Gasoline, 87 Octane min. |
Always verify specifications against your owner's manual for your specific serial number range.
Common Issues & Recommended Parts
Below are common maintenance scenarios for the Mercury 115 EFI (4-STROKE):
-
Water Pump / Overheating: If the tell-tale stream is weak or absent, the water pump impeller likely needs replacement. Inspect annually or every 100 hours. → Recommended: Water Pump Impeller Kit
-
Engine Oil / Maintenance Light: 4-stroke engines require regular oil and filter changes. Use marine-grade oil rated for your engine. Change every 100 hours or annually. → Recommended: Oil Filter, Engine Oil
-
Fuel Injector Issues (EFI models): Rough idle or misfires may indicate clogged fuel injectors. Use fuel stabilizer and clean injectors periodically. → Recommended: Fuel Injector, Fuel Filter
-
Gear Case Oil Leak: Check lower unit seals if gear oil appears milky (water contamination). Replace seals and gaskets during lower unit service. → Recommended: Lower Unit Seal Kit, Drain Plug Gaskets
-
Anode Corrosion: Inspect sacrificial anodes regularly, especially in saltwater. Replace when 50% depleted to protect against galvanic corrosion. → Recommended: Zinc/Aluminum Anode Kit
Parts Diagrams & OEM Part Numbers
Expand the sections below to view detailed exploded parts diagrams and find the exact OEM replacement components for your Mercury 115 EFI (4-STROKE).
▶Accessories (1 parts)
| Ref |
OEM Part # |
Part Name |
| 0 |
56-883040A1 |
TACH MODULE KIT |
▶Air Compressor (37 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
8M0050654 |
COMPRESSOR ASSEMBLY, Air |
| 2 |
8M0114192 |
END CAP |
| 3 |
25-86391 |
O-RING |
| 4 |
657-853658T02 |
CONNECTING ROD ASSEMBLY |
| 5 |
NSS |
NOT SOLD SEPARATE, Piston Assy. (With Rings) |
| 6 |
53-854638 |
LOCK RING |
| 7 |
853584A10 |
REED PLATE ASSEMBLY |
| 8 |
27-854442 |
GASKET |
| 9 |
27-854443 |
GASKET |
| 10 |
854334T02 |
HEAD, Compressor |
| 11 |
22-38565 |
FITTING, (.375-18) |
| 12 |
10-82446035 |
SCREW, (M8 x 35) |
| 13 |
22-996642 |
FITTING, Elbow 90 Degree (.125-27 x .250) Nylon |
| 14 |
22-856744 |
FITTING |
| 15 |
25-831985 |
O-RING, (.468 x .078) |
| 16 |
8M0148668 |
SENSOR ASSEMBLY |
| 17 |
25-896699 |
O-RING, (.351 x .072) |
| 18 |
21-888421 |
CHECK VALVE |
| 19 |
8215832 |
PIN, Special |
| 20 |
22-15133 |
FITTING |
| 21 |
8M0214940 |
TIE STRAP, (5.50 Inches) |
| 22 |
32-88306955 |
HOSE, (.125 x 25.00 Inches) |
| 23 |
21-889851 |
CONNECTOR |
| 24 |
10-82130025 |
SCREW, (M6 x 25) |
| 25 |
853944T03 |
PULLEY |
| 26 |
10-85593912 |
SCREW, (M6 x 12) |
| 27 |
8M0047394 |
TENSIONER ARM |
| 28 |
8547971 |
PULLEY |
| 29 |
10-4010825 |
SCREW, (M10 x 25) Hex Flange - Stainless Steel |
| 30 |
30-8570111 |
BEARING, Flanged |
| 31 |
23-856549001 |
BUSHING |
| 32 |
32-88104441 |
TUBING, (18.00 Inches Bulk), Cut to 8 Inches |
| 33 |
24-8547953 |
SPRING |
| 34 |
10-4000382 |
SCREW, (M10 x 60) |
| 35 |
32-88104441 |
TUBING, (18.00 Inches Bulk), Cut to 13 Inches |
| 36 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 37 |
10-82446090 |
SCREW, (M8 x 90) |
▶Air Hoses (7 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
32-85525884 |
HOSE, (32.00 Inches) (Cut to 8 Inches |
| 2 |
54-8M0214964 |
CLAMP, Hose (15.3) |
| 3 |
32-885376 |
HOSE, Air |
| 4 |
32-881041A1 |
HOSE ASSEMBLY, Air By-Pass |
| 5 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 6 |
881197 |
MUFFLER, Air |
| 7 |
32-85833939 |
HOSE, (17.00 Inches Bulk) (Cut to 4-1/2 Inches |
▶Bleed System (5 parts)
| Ref |
OEM Part # |
Part Name |
| 0 |
891767A07 |
POWERHEAD ASSEMBLY Comment: 90/115 |
| 1 |
22-59169003 |
FITTING, Tee |
| 2 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 3-1/4 Inches) |
| 3 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 3-1/4 Inches) |
| 4 |
32-8M0054152 |
TUBING, (38.00 Inches Bulk) (Cut to 19 Inches) |
▶Bottom Cowl (39 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
100-878587A1 |
BOTTOM COWL ASSEMBLY Comment: (PORT) |
| 2 |
100-8M0113913 |
BOTTOM COWL ASSEMBLY Comment: (STARBOARD) |
| 3 |
8M0109217 |
SEAL, Cowl (41.00 Inches) |
| 4 |
878547T |
INSERT |
| 5 |
10-82130040 |
SCREW, (M6 x 40) |
| 6 |
831209 |
RETAINER |
| 7 |
858742 |
BOOT, Idle Exhaust |
| 8 |
8M0039078 |
GROMMET |
| 9 |
22-827948 |
FITTING |
| 10 |
12-855576 |
WASHER |
| 11 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 12 |
32-881535 |
HOSE, (32.00 Inches) |
| 13 |
32-8M0108355 |
HOSE, (57.00 Inches Bulk) (Cut to 5 IN.) |
| 14 |
32-9912688 |
TUBING, (36.00 Inches Bulk) (Cut to 26 IN.) |
| 15 |
22-817518 |
TEE |
| 16 |
10-82130020 |
SCREW, (M6 x 20) |
| 17 |
25-889724 |
GROMMET |
| 18 |
87-8M0042301 |
SWITCH ASSEMBLY |
| 19 |
889740A02 |
HANDLE KIT Comment: PLASTIC HANDLE |
| 20 |
10-824868 |
SCREW, (M6 x 75) Comment: USE W/CAST HANDLE |
| 21 |
23-33589 |
BUSHING |
| 22 |
25-48462 |
O-RING, (.614 x .070) |
| 23 |
8219423 |
PAWL |
| 24 |
12-69057 |
WASHER, (.281 x .734 x .063) |
| 25 |
11-401366 |
NUT, (M6) Stainless Steel |
| 26 |
13541 |
PLUG, Male |
| 27 |
25-855362001 |
GROMMET Comment: SN# 0T980000 & Up |
| 28 |
23-855364 |
BUSHING |
| 29 |
8M0043167 |
SEAL, Lower Cowl (44.75 Inches) |
| 30 |
87-8M0235191 |
SWITCH, Trim |
| 31 |
22-94848 |
FITTING |
| 32 |
888508 |
RETAINER, Cable |
| 33 |
884464 |
BOOT, Idle Relief |
| 34 |
8M0000504 |
CLAMP, Upper |
| 35 |
8M0000484 |
CLAMP, Lower |
| 36 |
10-82130016 |
SCREW, (M6 x 16) |
| 37 |
859343 |
FOAM |
| 38 |
54-850181 |
TIE STRAP, (11.750 Inches) |
| 39 |
23-892427 |
SPACER |
▶Crankshaft, PISTONS AND CONNECTING RODS (11 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-858732T02 |
GASKET SET, Powerhead |
| 1 |
2406-880894T |
CRANKSHAFT |
| 2 |
26-8040992 |
SEAL, Oil |
| 3 |
26-8041002 |
SEAL, Oil |
| 4 |
31-804101T20 |
BEARING Comment: (RED) |
| 5 |
31-804102T30 |
BEARING Comment: (RED) |
| 6 |
31-804103T20 |
BEARING Comment: (RED) |
| 7 |
2715-880895A16 |
PISTON ASSEMBLY Comment: (.25MM O/S) |
| 8 |
10-880896 |
BOLT, (M8 x 38) |
| 9 |
39-880898T02 |
RING SET, Piston Comment: (.25 MM O/S) |
| 10 |
31-880899T30 |
BEARING Comment: (RED) |
▶Crankshaft, Pistons and Connecting Rods (22 parts)
| Ref |
OEM Part # |
Part Name |
| 0 |
891767A07 |
POWERHEAD ASSEMBLY Comment: (90/115) |
| 1 |
400-879633T01 |
CRANKSHAFT ASSEMBLY |
| 2 |
53-880119 |
RING, Retaining |
| 3 |
30-43011T |
BEARING, Ball (LOWER) |
| 4 |
28-91800 |
KEY, Woodruff |
| 5 |
786611 |
WEAR SLEEVE |
| 6 |
25-35126 |
O-RING, (.859 x .139) |
| 7 |
39-8M0071643 |
RING, Seal |
| 8 |
31-879848A02 |
BEARING |
| 9 |
NSS |
NOT SOLD SEPARATE, Needle Bearing |
| 10 |
700-896962A02 |
PISTON ASSEMBLY Comment: (.030 Oversize) |
| 11 |
NSS |
NOT SOLD SEPARATE, Piston Pin |
| 12 |
40-841202 |
RING |
| 13 |
39-875257A12 |
RING SET, Piston Comment: (.030 Oversize) |
| 14 |
600-888470T06 |
CONNECTING ROD ASSEMBLY Comment: SN# 1B189549 & Up |
| 15 |
12-88263 |
THRUST WASHER |
| 16 |
29-8M0204715 |
BEARING, Needle |
| 17 |
10-94320 |
SCREW, (.375-24 x 1.250) |
| 18 |
31-844338A01 |
BEARING/CAGE KIT Comment: SN# 1B189549 & Up |
| 19 |
NSS |
NOT SOLD SEPARATE, Roller Bearing |
| 20 |
31-879853A01 |
BEARING ASSEMBLY, Roller (UPPER) |
| 21 |
26-879635 |
SEAL, Oil |
▶Cylinder Block (37 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881421T04 |
POWERHEAD ASSEMBLY |
| 1 |
892-881422T05 |
CYLINDER BLOCK |
| 2 |
17-82364M |
PIN, Dowel |
| 3 |
27-858732002 |
GASKET |
| 4 |
10-8M0101617 |
BOLT, (M8 x 55) Comment: SN# 0T980000 & Up |
| 5 |
10-804072 |
BOLT, (M10 x 135) |
| 6 |
25-855690 |
GROMMET |
| 7 |
804073 |
LIFTING EYE |
| 8 |
10-8257021 |
BOLT, (M6 x 20) |
| 9 |
19-825953 |
PLUG, (M14 x 12) |
| 10 |
27-81990M |
GASKET |
| 11 |
35-8M0162830 |
FILTER, Oil |
| 12 |
10-804097 |
BOLT |
| 13 |
881424T02 |
COVER, Outer Exhaust |
| 14 |
27-804076003 |
GASKET |
| 15 |
10-881427 |
BOLT, (M6 x 30) |
| 16 |
10-881425 |
SCREW |
| 17 |
27-881426 |
GASKET |
| 18 |
NSS |
NOT SOLD SEPARATE, Anode Comment: Order Cover |
| 19 |
25-804086 |
GROMMET |
| 20 |
804085 |
COVER |
| 21 |
10-8524741 |
BOLT, (M6 x 20) |
| 22 |
10-827207 |
BOLT, (M8 x 25) |
| 23 |
25-804082 |
GROMMET |
| 24 |
804080001 |
VALVE, Pressure Control |
| 25 |
24-804081 |
SPRING |
| 26 |
27-804084 |
GASKET |
| 27 |
804083001 |
COVER |
| 28 |
10-881428 |
BOLT, (M6 x 16) |
| 29 |
54-804089 |
CLIP |
| 30 |
32-804088 |
HOSE |
| 31 |
56762 |
TIE STRAP, (4.00 Inches) |
| 32 |
16-8587331 |
STUD |
| 33 |
12-8M0214963 |
WASHER, (.406 x .750 x .105) Stainless Steel |
| 34 |
11-40140 |
NUT, (M10) |
| 35 |
10-81893435 |
SCREW, (M8 x 35) |
| 36 |
881600 |
CAP, Rubber |
▶Cylinder Block and Crankcase (36 parts)
| Ref |
OEM Part # |
Part Name |
| 0 |
891767A07 |
POWERHEAD ASSEMBLY Comment: 90/115 |
| 1 |
800-878581A09 |
CYLINDER BLOCK Comment: (90/115) |
| 2 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) |
| 3 |
17-8M0036405 |
PIN, Center Main |
| 4 |
10-4009680 |
SCREW, (M10 x 80) |
| 5 |
8M0111325 |
BRACKET |
| 6 |
10-81742740 |
SCREW, (M8 x 40) |
| 7 |
22-36382 |
FITTING, (.250-18 x .62) Brass |
| 8 |
22-185981 |
PLUG, Pipe (.375-18) |
| 9 |
10-82127335 |
SCREW, (M8 x 35) |
| 10 |
22-996642 |
FITTING, Elbow 90 Degree (.125-27 x .250) Nylon |
| 11 |
21-883139001 |
CHECK VALVE |
| 12 |
21-889830 |
CHECK VALVE |
| 13 |
22-782792 |
FITTING, Elbow 45 Degree (1.25) |
| 14 |
21-8282182 |
CHECK VALVE |
| 15 |
8248576 |
DEFLECTOR, Water |
| 16 |
22-185981 |
PLUG, Pipe (.375-18) |
| 17 |
22-881866 |
FITTING |
| 18 |
16-892561001 |
STUD, (M10 x 136) |
| 19 |
12-8M0214963 |
WASHER, (.406 x .750 x .105) Stainless Steel |
| 20 |
11-40140 |
NUT, (M10) |
| 21 |
21-8592352 |
CHECK VALVE, 90 Degree (.0625-27) |
| 22 |
891956 |
SEAL |
| 23 |
22-8M0180565 |
PLUG, Pipe (.375-18) Brass |
| 24 |
10-81742720 |
SCREW, (M8 x 20) |
| 25 |
8M0082988 |
SENSOR, Crank Position |
| 26 |
10-40011107 |
SCREW, (M5 x 16) Stainless Steel |
| 27 |
880198T |
COVER, Flywheel |
| 28 |
25-8M0153609 |
GROMMET Comment: SN# 0T931541 & Up |
| 29 |
22-857175 |
COUPLING INSERT |
| 30 |
22-857176 |
COUPLING BODY |
| 31 |
19-858240 |
CAP |
| 32 |
32-8M0108349 |
TUBING, (.312) (70.00 Inches Bulk) (Cut to 43 Inches) |
| 33 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 34 |
22-835454001 |
FITTING |
| 35 |
880731002 |
BRACKET, Oil Reservoir |
▶Cylinder Head (32 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881421T04 |
POWERHEAD ASSEMBLY |
| 1 |
881310T08 |
CYLINDER HEAD ASSEMBLY |
| 2 |
17-804110 |
PIN, Guide |
| 3 |
19-804111 |
PLUG |
| 4 |
10-804112 |
BOLT, (M7 x 48) |
| 5 |
17-804113 |
PIN, Dowel |
| 6 |
10-804114 |
BOLT, (M7 x 37) |
| 7 |
10-881311 |
BOLT, (M10 x 145) |
| 8 |
23-8M0070515 |
COLLAR |
| 9 |
27-8041151 |
GASKET |
| 10 |
10-83124714 |
BOLT |
| 11 |
12-831246 |
WASHER, Sealing |
| 12 |
10-881312 |
BOLT, (M8 x 55) |
| 13 |
NSS |
NOT SOLD SEPARATE, Anode Comment: Order Cover |
| 14 |
25-804086 |
GROMMET |
| 15 |
804085 |
COVER |
| 16 |
10-8524741 |
BOLT, (M6 x 20) |
| 17 |
10-827207 |
BOLT, (M8 x 25) |
| 18 |
33-881284Q |
SPARK PLUG |
| 19 |
881429 |
THERMOSTAT |
| 20 |
8041271 |
THERMOSTAT COVER |
| 21 |
10-8248326 |
SCREW, (M6 x 25 MM) |
| 22 |
881313T1 |
COVER KIT |
| 23 |
804119 |
COVER, Breather |
| 24 |
10-804120 |
SCREW, (M4 x 8) |
| 25 |
27-804123 |
GASKET |
| 26 |
25-855690 |
GROMMET |
| 27 |
10-858530 |
BOLT, (M6 x 30) |
| 28 |
859578A1 |
PLUG ASSEMBLY, Oil |
| 29 |
NSS |
NOT SOLD SEPARATE, O Ring |
| 30 |
858752001 |
COVER |
| 31 |
10-1993716 |
SCREW, (M6 x 16) |
▶Driveshaft Housing (24 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
1507-858576T2 |
HOUSING ASSEMBLY, Driveshaft |
| 2 |
16-9035015 |
STUD, (M10 x 227) Comment: (X-LONG) |
| 3 |
16-8M0034462 |
STUD, (M10 x 190) Comment: (X-LONG) |
| 4 |
12-8M0214963 |
WASHER, (.406 x .750 x .105) Stainless Steel |
| 5 |
11-40140 |
NUT, (M10) |
| 6 |
22-85822A15 |
PICKUP ASSEMBLY, Speedometer |
| 7 |
22-433351 |
CONNECTOR, 90 Degree (.125-27) Nylon |
| 8 |
22-85822T |
CONNECTOR, Straight |
| 9 |
44343T1 |
MOUNT |
| 10 |
10-898835001 |
BOLT, (M12 x 154) |
| 11 |
12-30119 |
WASHER, (.875 Inch Outside Diameter) |
| 12 |
11-8M0204662 |
NUT, (M12) |
| 13 |
88238A10 |
CABLE ASSEMBLY, Ground |
| 14 |
10-41508 |
SCREW, (.250-20 x .500) Stainless Steel |
| 15 |
858916T |
CLAMP |
| 16 |
10-4010725 |
SCREW, (M8 x 25) |
| 17 |
8M0142713 |
CAP |
| 18 |
23-859550 |
BUSHING |
| 19 |
17-24873 |
PIN, Alignment |
| 20 |
22-855622 |
FITTING |
| 21 |
12092A3 |
SPACER KIT Comment: (X-LONG) |
| 22 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) Comment: (X-LONG) |
| 23 |
23-813745 |
SPACER Comment: (X-LONG) |
| 24 |
54-816311T |
TIE STRAP, (8.00 Inches) |
▶Electrical Components (64 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
881363T |
COVER |
| 2 |
881359T |
BRACKET |
| 3 |
84-881364T04 |
HARNESS ASSEMBLY |
| 4 |
88-832969T20 |
FUSE, 20 Ampere |
| 5 |
88-8M0057159 |
FUSE, 30 Ampere |
| 6 |
891824020 |
COVER, Fuse Comment: (GREEN) |
| 7 |
881362 |
BRACKET |
| 8 |
10-8813511 |
SCREW |
| 9 |
881352T |
RELAY |
| 10 |
12-82214M |
WASHER |
| 11 |
13-82212M |
LOCKWASHER |
| 12 |
10-96671M |
SCREW |
| 13 |
85-804284001 |
BOOT |
| 14 |
881350T |
RELAY |
| 15 |
10-881351 |
SCREW |
| 16 |
54-881353 |
CLAMP |
| 17 |
10-8813511 |
SCREW |
| 18 |
54-881361 |
CLAMP |
| 19 |
54-881360 |
CLAMP |
| 20 |
10-804270 |
BOLT, (M6 x 28) |
| 21 |
25-881304 |
GROMMET |
| 22 |
23-804344003 |
BUSHING |
| 23 |
10-804604 |
BOLT, (M6 x 20) |
| 24 |
10-8248324 |
SCREW, (M6 x 16) |
| 25 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 26 |
84-858740T4 |
HARNESS ASSEMBLY, Adaptor Assy.-Remote |
| 27 |
8M0026570 |
TACH MODULE |
| 28 |
92753 |
RETAINER |
| 29 |
84-88439A33 |
CABLE ASSEMBLY, Positive - Battery |
| 30 |
84-88439A10 |
CABLE ASSEMBLY, Negative - Battery |
| 31 |
11-401388 |
NUT, (M8) Stainless Steel |
| 32 |
10-8M0204741 |
SCREW, (M6 x 20) Stainless Steel |
| 33 |
84-858723T1 |
HARNESS ASSEMBLY, Adaptor/Trim |
| 34 |
84-858914T1 |
HARNESS ASSEMBLY, Trim Motor Adaptor |
| 35 |
859249T1 |
CONNECTOR |
| 36 |
37-8272822 |
DECAL, Warning, High Voltage |
| 37 |
37-881865 |
DECAL, Caution-Start in Gear Comment: (Start In Gear) |
| 38 |
882751A3 |
RELAY KIT, Trim |
| 39 |
84-826802A24 |
HARNESS ASSEMBLY, Trim |
| 40 |
8M0207773 |
RELAY ASSEMBLY |
| 41 |
25-818967 |
GROMMET |
| 42 |
23-8M0214955 |
BUSHING |
| 43 |
NSS |
NOT SOLD SEPARATE, Decal |
| 44 |
828102 |
BRACKET |
| 45 |
10-824868 |
SCREW, (M6 x 75) |
| 46 |
12-8M0214930 |
WASHER |
| 47 |
23-823807 |
BUSHING |
| 48 |
804289 |
PULLER, Fuse |
| 49 |
84-88439A25 |
CABLE ASSEMBLY, Battery - Positive |
| 50 |
85-8500671 |
BOOT, Insulator - Red |
| 51 |
23-8502341 |
BUSHING |
| 52 |
12-4002318 |
WASHER |
| 53 |
10-82446035 |
SCREW, (M8 x 35) |
| 54 |
25-833155 |
GROMMET |
| 55 |
880192T01 |
COVER |
| 56 |
25-8M0153609 |
GROMMET Comment: SN# 0T931541 & Up |
| 57 |
84-856583A07 |
CABLE ASSEMBLY, (12.00 Inches) Black |
| 58 |
889992 |
SPACER |
| 59 |
858953 |
BRACKET |
| 60 |
22-875207 |
TEE, Fitting |
| 61 |
32-85978571 |
TUBING, (52.00 Inches Bulk), Cut to 1-1/2 Inches |
| 62 |
32-85978571 |
TUBING, (52.00 Inches Bulk), Cut to 52 Inches |
| 63 |
22-8M0214971 |
COUPLER |
| 64 |
22-859732 |
PLUG |
▶Engine Overhaul Gasket Set Components (2 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-879855A04 |
GASKET SET, Powerhead |
| 0 |
891956 |
SEAL, Cylinder Block |
▶Exhaust Plate (34 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
897580A05 |
ADAPTOR PLATE ASSEMBLY |
| 2 |
17-23784 |
PIN, Dowel |
| 3 |
22-880090 |
FITTING |
| 4 |
21-817519A2 |
CHECK VALVE ASSEMBLY, Drain |
| 5 |
25-19565002 |
GROMMET Comment: SN# 0T943820 & Up |
| 6 |
27-8585831 |
GASKET |
| 7 |
858572T01 |
SUMP, Oil |
| 8 |
858584A1 |
TUBE ASSEMBLY, Exhaust |
| 9 |
25-881295 |
O-RING |
| 10 |
25-89417004 |
GROMMET Comment: SN# 0T928617 & Up |
| 11 |
32-8M0026129 |
TUBE, Water Comment: (X-LONG) |
| 12 |
814080001 |
SEAL (Upper) Comment: SN# 0T980000 & Up |
| 13 |
858571T |
TUBE, Oil Pick Up |
| 14 |
25-859082 |
O-RING |
| 15 |
10-8M0204741 |
SCREW, (M6 x 20) Stainless Steel |
| 16 |
10-8M0214957 |
SCREW, (M6 x 30) |
| 17 |
8M0039073 |
SEAL |
| 18 |
8288181 |
PLUG, Drain |
| 19 |
27-8M0204692 |
GASKET |
| 20 |
10-82483213 |
SCREW, (M6 x 60) |
| 21 |
8596021 |
DIPSTICK |
| 22 |
10-4010750 |
SCREW, (M8 x 50) |
| 23 |
22-479452 |
PLUG |
| 24 |
22-889567 |
PLUG, (.500-14) |
| 25 |
23-27132 |
BUSHING |
| 26 |
888835A1 |
SHIFT SHAFT |
| 27 |
888840 |
SHIFT LINK |
| 28 |
888917 |
ROLLER |
| 29 |
23-891658 |
BUSHING |
| 30 |
888823001 |
SHIFT DETENT ASSEMBLY |
| 31 |
18-82053M |
PIN, Hair |
| 32 |
12-888832 |
WASHER |
| 33 |
12-69056 |
WASHER, (.255 x .620 x .030) Stainless Steel |
| 34 |
18-26953 |
COTTER PIN |
▶Flywheel (25 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881421T04 |
POWERHEAD ASSEMBLY |
| 1 |
881343T1 |
FLYWHEEL COVER |
| 2 |
10-804348 |
BOLT, (M6 x 20) |
| 3 |
825665 |
COLLAR |
| 4 |
25-11416T |
GROMMET |
| 5 |
11-804265A1 |
NUT/WASHER KIT, Hex (36 mm) |
| 6 |
12-8042641 |
WASHER, Plate |
| 7 |
280-881335T |
FLYWHEEL |
| 8 |
881337T |
COIL, Pulser |
| 9 |
398-881336T2 |
STATOR |
| 10 |
10-881338 |
SCREW, (M6 x 28) |
| 11 |
10-881339002 |
SCREW, (M4 x 8) |
| 12 |
54-881340 |
CLAMP |
| 13 |
10-804603 |
BOLT, (M6 x 30) |
| 14 |
17-825010 |
PIN, Dowel |
| 15 |
881341 |
ROTOR |
| 16 |
28-881342 |
KEY |
| 17 |
804266001 |
TIMING PLATE |
| 18 |
10-804267 |
SCREW |
| 19 |
NSS |
NOT SOLD SEPARATE, Decal-Warning Neutral |
| 20 |
NSS |
NOT SOLD SEPARATE, Decal-Warning Spinning Flywheel |
| 21 |
NSS |
NOT SOLD SEPARATE, Decal-Servicing Referral |
| 22 |
NSS |
NOT SOLD SEPARATE, Decal-Engine Oil/Valve |
| 23 |
NSS |
NOT SOLD SEPARATE, Decal-Emergency Starting |
| 24 |
37-881839A05 |
DECAL, EPA Label Information Comment: 2005 |
▶Flywheel and Alternator (17 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
200-878588T08 |
FLYWHEEL |
| 2 |
888842T01 |
DAMPER |
| 3 |
10-8M0143223 |
SCREW, (M8 x 20) |
| 4 |
57-8M0026410 |
BELT |
| 5 |
8M6013461 |
ALTERNATOR |
| 6 |
10-82130150 |
SCREW, (M10 x 50) |
| 7 |
12-4002319 |
WASHER |
| 8 |
84-856583A5 |
CABLE ASSEMBLY |
| 9 |
11-401386 |
NUT, (M6) Stainless Steel |
| 10 |
879856T02 |
BRACKET, Alternator |
| 11 |
8215832 |
PIN, Special |
| 12 |
23-856975 |
MOUNT |
| 13 |
10-82130145 |
SCREW, (M10 x 45) |
| 14 |
12-855725 |
WASHER |
| 15 |
19-45907 |
PLUG, Yellow |
| 16 |
12-33001 |
WASHER, (.641 x 1.250 x .190) |
| 17 |
11-42979 |
NUT, (M16) |
▶Fuel Injection Nozzle (28 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881440T04 |
INTAKE ASSEMBLY |
| 1 |
880888T02 |
REGULATOR, Fuel Pressure |
| 2 |
10-881524 |
SCREW, (M6 x 12) |
| 3 |
13-881525 |
LOCKWASHER |
| 4 |
54-881531 |
CLIP |
| 5 |
32-881528 |
HOSE |
| 6 |
10-881509 |
SCREW, (M5 x 15) |
| 7 |
54-881530 |
CLIP |
| 8 |
10-84088M |
SCREW, (M6 x 10) |
| 9 |
27-827610 |
GASKET |
| 10 |
23-888260 |
COLLAR |
| 11 |
881527T01 |
COOLER |
| 12 |
10-881507 |
BOLT, (M6 x 25) |
| 13 |
12-881533 |
WASHER |
| 14 |
8M0214940 |
TIE STRAP, (5.50 Inches) |
| 15 |
32-881536 |
HOSE |
| 16 |
32-881529 |
HOSE |
| 17 |
56762 |
TIE STRAP, (4.00 Inches) |
| 18 |
881518T |
DELIVERY PIPE |
| 19 |
880887T1 |
INJECTOR |
| 20 |
25-885183A1 |
O-RING KIT |
| 21 |
881520 |
CAP |
| 22 |
10-881534 |
BOLT, (M6 x 10) |
| 23 |
10-881532 |
BOLT, (M8 x 45) |
| 24 |
12-881508 |
WASHER |
| 25 |
23-881526 |
COLLAR |
| 26 |
881521T |
NIPPLE |
| 27 |
25-881522 |
O-RING |
▶Fuel Injection Pump (35 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881440T04 |
INTAKE ASSEMBLY |
| 1 |
881316T2 |
COVER |
| 2 |
25-881318 |
O-RING |
| 3 |
881329 |
NEEDLE VALVE KIT |
| 4 |
NSS |
NOT SOLD SEPARATE |
| 5 |
881320 |
FLOAT |
| 6 |
17-881321 |
PIN, Float |
| 7 |
881319T |
BODY |
| 8 |
881327 |
PLATE |
| 9 |
10-8813261 |
SCREW, (M3 x 8) (M3 x 8 MM) |
| 10 |
10-881326 |
SCREW, (M4 x 16) (M4 x 16 MM) |
| 11 |
27-881325 |
GASKET |
| 12 |
25-8M0070200 |
DAMPER Comment: SN# 0T980000 & Up |
| 13 |
8M0123823 |
PUMP, Fuel |
| 14 |
35-881323T |
FILTER |
| 15 |
881324 |
COVER |
| 16 |
10-8813262 |
SCREW, Drain |
| 17 |
27-881328 |
GASKET |
| 18 |
32-881330A02 |
HOSE KIT |
| 19 |
54-881331 |
CLIP |
| 20 |
54-881559 |
CLIP |
| 21 |
35-892758002 |
FILTER KIT, Fuel Comment: (DESIGN II) |
| 22 |
32-881560 |
HOSE |
| 23 |
22-8815581 |
TEE |
| 24 |
32-881554 |
HOSE |
| 25 |
32-881554 |
HOSE |
| 26 |
32-881554 |
HOSE |
| 27 |
32-881554 |
HOSE |
| 28 |
32-881555 |
HOSE |
| 29 |
32-881557 |
HOSE |
| 30 |
32-881556 |
HOSE |
| 31 |
25-8813221 |
DAMPER |
| 32 |
23-881332 |
COLLAR |
| 33 |
54-881537 |
CLAMP Comment: (DESIGN II) |
| 34 |
32-881565 |
HOSE Comment: (DESIGN I) |
▶Fuel Pump (38 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881310T09 |
CYLINDER HEAD ASSEMBLY |
| 1 |
880890T1 |
PUMP, Fuel |
| 2 |
NSS |
NOT SOLD SEPARATE, Body |
| 3 |
24-881544 |
SPRING |
| 4 |
881545 |
PLUNGER |
| 5 |
24-881546 |
SPRING |
| 6 |
881547 |
DIAPHRAGM |
| 7 |
17-881548 |
PIN |
| 8 |
NSS |
NOT SOLD SEPARATE, Body |
| 9 |
NSS |
NOT SOLD SEPARATE, Diaphragm |
| 10 |
NSS |
NOT SOLD SEPARATE, Body |
| 11 |
10-881550 |
SCREW |
| 12 |
11-881333 |
NUT |
| 13 |
25-8M0050719 |
O-RING |
| 14 |
56762 |
CLAMP |
| 15 |
10-804256 |
BOLT, (M6 x 30) |
| 16 |
32-881543002 |
HOSE |
| 17 |
881542 |
BRACKET |
| 18 |
10-811188T |
BOLT, (M6 x 16) |
| 19 |
11-82382M |
NUT Comment: SN# 0T980000 & Up |
| 20 |
35-881538T02 |
FILTER ASSEMBLY |
| 21 |
35-8M0168897 |
ELEMENT |
| 22 |
25-826966T |
O-RING |
| 23 |
881541 |
FLOAT |
| 24 |
881539 |
CUP |
| 25 |
56762 |
CLAMP |
| 26 |
804260 |
BRACKET |
| 27 |
10-804112 |
BOLT, (M7 x 48) |
| 28 |
17-804113 |
PIN, Dowel |
| 29 |
12-84292M |
WASHER |
| 30 |
804257 |
LEVER, Fuel Change |
| 31 |
881334 |
SHAFT |
| 32 |
17-82738M |
PIN |
| 33 |
32-8M0108349 |
TUBING, (.312) (70.00 Inches Bulk) (Cut to 55 IN.) |
| 34 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 35 |
22-822769 |
CONNECTOR |
| 36 |
NSS |
NOT SOLD SEPARATE, Cap |
| 37 |
32-828547633 |
CONDUIT, (.620 Inside Diameter x 3.00 Feet Bulk) |
▶Fuel Rail (24 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
880037T03 |
FUEL RAIL ASSEMBLY |
| 2 |
19-804834 |
PLUG |
| 3 |
804532 |
O-RING KIT |
| 4 |
54-804830 |
CLAMP |
| 5 |
10-804525001 |
SCREW PACKAGE, (2 Per)(M5 x 10) Comment: (M5 x 10) |
| 6 |
25-804840 |
O-RING KIT |
| 7 |
22-291112 |
FITTING |
| 8 |
891820 |
BRACKET |
| 9 |
8M0222157 |
INJECTOR |
| 10 |
25-804530 |
O-RING KIT |
| 11 |
25-804529 |
O-RING KIT |
| 12 |
804522 |
CLAMP |
| 13 |
8M0047053 |
VALVE ASSEMBLY, (.375 Inch Diameter), SCHRADER |
| 14 |
22-805515 |
CAP, Shrader Valve - Brass |
| 15 |
25-804840 |
O-RING KIT |
| 16 |
8M0041097 |
CLAMP |
| 17 |
22-996642 |
FITTING, Elbow 90 Degree (.125-27 x .250) Nylon |
| 18 |
19-804835 |
PLUG |
| 19 |
804532 |
O-RING KIT (16 per kit) |
| 20 |
25-804536 |
O-RING |
| 21 |
54-804832 |
CLAMP |
| 22 |
25-804840 |
O-RING KIT |
| 23 |
22-804836002 |
FITTING Comment: (Flange thickness is 8.65MM) |
| 24 |
22-804836001 |
FITTING Comment: (Flange thickness is 2.65MM) |
▶Fuel System (15 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
32-889712001 |
HOSE, Vent, To Vent Fitting |
| 2 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 3 |
32-881040A1 |
HOSE ASSEMBLY, Fuel Supply |
| 4 |
32-878506A1 |
HOSE ASSEMBLY, Fuel By-Pass |
| 5 |
884820 |
SHRADER VALVE |
| 6 |
25-891778 |
O-RING |
| 7 |
54-884819 |
CLIP |
| 8 |
10-82130012 |
SCREW, (M6 x 12) |
| 9 |
32-8M0108349 |
TUBING, (.312) (70.00 Inches Bulk) (Cut to 6-1/2 Inches) To Crankcase |
| 10 |
22-822769 |
CONNECTOR |
| 11 |
32-8M0108349 |
TUBING, (.312) (70.00 Inches Bulk) (Cut to 28 Inches) |
| 12 |
32-8M0108349 |
TUBING, (.312) (70.00 Inches Bulk) (Cut to 8-1/2 Inches |
| 13 |
54-8M0214964 |
CLAMP, Hose (15.3) |
| 14 |
32-883545002 |
HOSE |
| 15 |
26-888852 |
SEAL, Fuel Director |
▶Gear Housing(Driveshaft)(2.07:1 Gear Ratio) (44 parts)
| Ref |
OEM Part # |
Part Name |
| - |
31-803496T2 |
BEARING/SEAL KIT (W/O Forward Bearing) |
| 0 |
1667-9011J35 |
GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG) |
| 1 |
1667-9011G59 |
GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC) |
| 2 |
17-8M0084244 |
PIN, Dowel - With Hole (.375 x .625) (FRONT) |
| 3 |
43046 |
TUBE, Oiler |
| 4 |
10-79953Q04 |
SCREW KIT, (.375-16 x .250) Drain |
| 5 |
12-191833 |
SEAL |
| 6 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) (REAR) |
| 7 |
31640T07 |
TRIM TAB |
| 8 |
10-825427 |
SCREW, (.437-14 x 1.250) Stainless Steel |
| 9 |
12-451761 |
WASHER, (.453 x .812 x .105) Black Oxide |
| 10 |
43040T1 |
CARRIER ASSEMBLY |
| 11 |
NSS |
NOT SOLD SEPARATE, Needle Bearing |
| 12 |
97-826134Q |
ANODE |
| 13 |
11-401386 |
NUT, (M6) Stainless Steel |
| 14 |
10-4000333 |
SCREW, (M6 x 40) |
| 15 |
43-881259T |
GEAR, Pinion - 14 Teeth Comment: (Also Part of 43-881260A3) |
| 16 |
11-35921 |
NUT, (.625-18) |
| 17 |
850307 |
CAM, Shift Control |
| 18 |
31-883047A1 |
BEARING ASSEMBLY, Tapered Roller |
| 19 |
15-44492A1 |
SHIM SET |
| 20 |
45-888934A1 |
DRIVESHAFT ASSEMBLY Comment: (X-LONG) |
| 21 |
42461A1 |
SLEEVE/RING KIT |
| 22 |
NSS |
NOT SOLD SEPARATE, Seal Ring |
| 23 |
43055A4 |
COVER ASSEMBLY, Water Pump |
| 24 |
27-430331 |
GASKET |
| 25 |
27-8M0214931 |
GASKET |
| 26 |
26-43036 |
SEAL, Oil (LOWER) |
| 27 |
26-43035 |
SEAL, Oil (UPPER) |
| 28 |
27-8172771 |
GASKET |
| 29 |
817275A2 |
HOUSING KIT, Upper Water Pump |
| 30 |
8M0204709 |
FACEPLATE |
| 31 |
10-82684430 |
SCREW, (M6 x 30) |
| 32 |
430232 |
SEAL |
| 33 |
28-8M0204723 |
KEY |
| 34 |
47-43026T2 |
IMPELLER |
| 35 |
10-82684425 |
SCREW, (M6 x 25) |
| 36 |
853908A1 |
SHIFT SHAFT ASSEMBLY Comment: (X-LONG - 17 IN.) |
| 37 |
53-29641 |
E RING |
| 38 |
23-43052A4 |
BUSHING ASSEMBLY |
| 39 |
25-8M0204681 |
O-RING, (1.424 x .103) |
| 40 |
26-8M0204708 |
SEAL, Oil |
| 41 |
10-82684425 |
SCREW, (M6 x 25) |
| 42 |
26-861415 |
FACE SEAL |
▶Gear Housing(Driveshaft)(2.07:1Gear Ratio) (44 parts)
| Ref |
OEM Part # |
Part Name |
| - |
47-8M0100526 |
REPAIR KIT, Water Pump Impeller |
| 0 |
1600-888845T02 |
GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG) |
| 1 |
1600-888845T |
GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC) |
| 2 |
17-8M0084244 |
PIN, Dowel - With Hole (.375 x .625) (FRONT) |
| 3 |
43046 |
TUBE, Oiler |
| 4 |
10-79953Q04 |
SCREW KIT, (.375-16 x .250) Drain |
| 5 |
12-191833 |
SEAL |
| 6 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) (REAR) |
| 7 |
31640T07 |
TRIM TAB |
| 8 |
10-825427 |
SCREW, (.437-14 x 1.250) Stainless Steel |
| 9 |
12-451761 |
WASHER, (.453 x .812 x .105) Black Oxide |
| 10 |
43040T1 |
CARRIER ASSEMBLY |
| 11 |
NSS |
NOT SOLD SEPARATE, Needle Bearing |
| 12 |
97-826134Q |
ANODE |
| 13 |
11-401386 |
NUT, (M6) Stainless Steel |
| 14 |
10-4000333 |
SCREW, (M6 x 40) |
| 15 |
NSS |
NOT SOLD SEPARATE, Pinion Gear (14 TEETH) Comment: (Part of 43-881260A3) |
| 16 |
11-35921 |
NUT, (.625-18) |
| 17 |
31-883047A1 |
BEARING ASSEMBLY, Tapered Roller |
| 18 |
15-44492A1 |
SHIM SET |
| 19 |
45-878575T1 |
DRIVESHAFT ASSEMBLY Comment: (X-LONG) |
| 20 |
42461A1 |
SLEEVE/RING KIT |
| 21 |
NSS |
NOT SOLD SEPARATE, Seal Ring |
| 22 |
43055A4 |
COVER ASSEMBLY, Water Pump |
| 23 |
27-430331 |
GASKET |
| 24 |
27-8M0214931 |
GASKET |
| 25 |
26-43036 |
SEAL, Oil (LOWER) |
| 26 |
26-43035 |
SEAL, Oil (UPPER) |
| 27 |
27-8172771 |
GASKET |
| 28 |
817275A2 |
HOUSING KIT, Upper Water Pump |
| 29 |
8M0204709 |
FACEPLATE |
| 30 |
10-82684430 |
SCREW, (M6 x 30) |
| 31 |
430232 |
SEAL |
| 32 |
28-8M0204723 |
KEY |
| 33 |
47-43026T2 |
IMPELLER |
| 34 |
10-82684425 |
SCREW, (M6 x 25) |
| 35 |
26-861415 |
FACE SEAL |
| 36 |
884565A00 |
SHIFT SHAFT ASSEMBLY Comment: (X-LONG) |
| 37 |
53-29641 |
E RING |
| 38 |
23-43052A4 |
BUSHING ASSEMBLY |
| 39 |
25-8M0204681 |
O-RING, (1.424 x .103) |
| 40 |
26-8M0204708 |
SEAL, Oil |
| 41 |
10-82684425 |
SCREW, (M6 x 25) |
| 42 |
23-891637 |
BUSHING Comment: (NOT included with complete replacement Gear Housings) |
▶Gear Housing(Driveshaft)(2.33:1 Gear Ratio) (44 parts)
| Ref |
OEM Part # |
Part Name |
| - |
31-803496T2 |
BEARING/SEAL KIT (W/O Forward Bearing) |
| 0 |
1667-9011J39 |
GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG) |
| 1 |
1667-9011G59 |
GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC) |
| 2 |
17-8M0084244 |
PIN, Dowel - With Hole (.375 x .625) (FRONT) |
| 3 |
43046 |
TUBE, Oiler |
| 4 |
10-79953Q04 |
SCREW KIT, (.375-16 x .250) Drain |
| 5 |
12-191833 |
SEAL |
| 6 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) (REAR) |
| 7 |
31640T07 |
TRIM TAB |
| 8 |
10-825427 |
SCREW, (.437-14 x 1.250) Stainless Steel |
| 9 |
12-451761 |
WASHER, (.453 x .812 x .105) Black Oxide |
| 10 |
43040T1 |
CARRIER ASSEMBLY |
| 11 |
NSS |
NOT SOLD SEPARATE, Needle Bearing |
| 12 |
97-826134Q |
ANODE |
| 13 |
11-401386 |
NUT, (M6) Stainless Steel |
| 14 |
10-4000333 |
SCREW, (M6 x 40) |
| 15 |
NSS |
NOT SOLD SEPARATE, Pinion Gear (12 Teeth) Comment: (PART OF 43-882813A3) |
| 16 |
11-35921 |
NUT, (.625-18) |
| 17 |
850307 |
CAM, Shift Control |
| 18 |
31-883047A1 |
BEARING ASSEMBLY, Tapered Roller |
| 19 |
15-44492A1 |
SHIM SET |
| 20 |
45-888934A1 |
DRIVESHAFT ASSEMBLY Comment: (X-LONG) |
| 21 |
42461A1 |
SLEEVE/RING KIT |
| 22 |
NSS |
NOT SOLD SEPARATE, Seal Ring |
| 23 |
43055A4 |
COVER ASSEMBLY, Water Pump |
| 24 |
27-430331 |
GASKET |
| 25 |
27-8M0214931 |
GASKET |
| 26 |
26-43036 |
SEAL, Oil (LOWER) |
| 27 |
26-43035 |
SEAL, Oil (UPPER) |
| 28 |
27-8172771 |
GASKET |
| 29 |
817275A2 |
HOUSING KIT, Upper Water Pump |
| 30 |
8M0204709 |
FACEPLATE |
| 31 |
10-82684430 |
SCREW, (M6 x 30) |
| 32 |
430232 |
SEAL |
| 33 |
28-8M0204723 |
KEY |
| 34 |
47-43026T2 |
IMPELLER |
| 35 |
10-82684425 |
SCREW, (M6 x 25) |
| 36 |
853908A1 |
SHIFT SHAFT ASSEMBLY Comment: (X-LONG) |
| 37 |
53-29641 |
E RING |
| 38 |
23-43052A4 |
BUSHING ASSEMBLY |
| 39 |
25-8M0204681 |
O-RING, (1.424 x .103) |
| 40 |
26-8M0204708 |
SEAL, Oil |
| 41 |
10-82684425 |
SCREW, (M6 x 25) |
| 42 |
26-861415 |
FACE SEAL |
▶Gear Housing, Propeller Shaft - 2.07:1 Gear Ratio (34 parts)
| Ref |
OEM Part # |
Part Name |
| - |
52-888805A00 |
REPAIR KIT, Clutch And Cam Follower |
| 0 |
1600-888845T02 |
GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG) |
| 1 |
1600-888845T |
GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC) |
| 2 |
8227731 |
INSERT, Threaded |
| 3 |
888807 |
FOLLOWER ASSEMBLY, Cam |
| 4 |
8M4504018 |
SHIFT CAM Comment: SN# 0T845782 & Up |
| 5 |
888806 |
ROD, Clutch Actuator |
| 6 |
17-8M0084243 |
PIN, Cross |
| 7 |
17-8M0084245 |
PIN, Spring Locator |
| 8 |
24-79910 |
SPRING |
| 9 |
12-78910 |
WASHER |
| 10 |
15-44491A1 |
SHIM SET |
| 11 |
31-30894A1 |
BEARING SET, Cup And Cone |
| 12 |
NSS |
NOT SOLD SEPARATE, Cup |
| 13 |
43-881260A3 |
GEAR, Forward - 29 Teeth (29 TEETH) |
| 14 |
31-30895T |
BEARING, Needle |
| 15 |
53-856823 |
RING, Retaining |
| 16 |
52-888805T |
CLUTCH |
| 17 |
44-8M0140444 |
PROPELLER SHAFT |
| 18 |
24-30893 |
SPRING |
| 19 |
43-889991T |
GEAR, Reverse (29 Teeth) (29 TEETH) |
| 20 |
8M0168901 |
CARRIER ASSEMBLY, Bearing |
| 21 |
25-8M0214974 |
O-RING, (3.609 x .139) |
| 22 |
31-30956T |
BEARING, Needle |
| 23 |
26-8M0205728 |
SEAL, Oil (INNER) |
| 24 |
26-8M0205729 |
SEAL, Oil (OUTER) |
| 25 |
31-12578T |
BEARING, Roller |
| 26 |
12-12577 |
THRUST WASHER |
| 27 |
31-12576 |
BEARING, Thrust |
| 28 |
16-8M0034456 |
STUD, (M8 x 48) |
| 29 |
12-855941 |
WASHER, (.323 x .590 x .112) Stainless Steel |
| 30 |
11-401378 |
NUT, (M8) |
| 31 |
NSS |
NOT SOLD SEPARATE, Decal-G/H Pinion Ident. |
| 32 |
NSS |
NOT SOLD SEPARATE, Lock Nut |
▶Gear Housing, Propeller Shaft - 2.33:1 Gear Ratio (34 parts)
| Ref |
OEM Part # |
Part Name |
| - |
31-803496T2 |
BEARING/SEAL KIT (W/O Forward Bearing) |
| 0 |
1667-9011J39 |
GEAR HOUSING ASSEMBLY, Complete (4.25 Inch/107.95 mm Torpedo Diameter) (COMPLETE) Comment: (X-LONG) |
| 1 |
1667-9011G59 |
GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC) |
| 2 |
31-30894A1 |
BEARING SET, Cup And Cone |
| 3 |
NSS |
NOT SOLD SEPARATE, Cup |
| 4 |
43-882813A3 |
GEAR KIT, Forward And Pinion 28 Teeth (28 TEETH) |
| 5 |
31-30895T |
BEARING, Needle |
| 6 |
53-856823 |
RING, Retaining |
| 7 |
850315A1 |
FOLLOWER KIT, Cam |
| 8 |
30-44530 |
BALL |
| 9 |
NSS |
NOT SOLD SEPARATE, Slide |
| 10 |
24-850327 |
SPRING |
| 11 |
52-850048T |
CLUTCH |
| 12 |
17-8M0100263 |
PIN, Cross |
| 13 |
24-30893 |
SPRING |
| 14 |
44-8M0140445 |
PROPELLER SHAFT |
| 15 |
43-882814T |
GEAR, Reverse - 28 Teeth (28 TEETH) |
| 16 |
8M0168901 |
CARRIER ASSEMBLY, Bearing |
| 17 |
25-8M0214974 |
O-RING, (3.609 x .139) |
| 18 |
31-30956T |
BEARING, Needle |
| 19 |
26-8M0205728 |
SEAL, Oil (INNER) |
| 20 |
26-8M0205729 |
SEAL, Oil (OUTER) |
| 21 |
31-12578T |
BEARING, Roller |
| 22 |
12-12577 |
THRUST WASHER |
| 23 |
31-12576 |
BEARING, Thrust |
| 24 |
16-8M0034456 |
STUD, (M8 x 48) (M8 X 48 MM) |
| 25 |
12-855941 |
WASHER |
| 26 |
11-401378 |
NUT, (M8) |
| 27 |
15-44491A1 |
SHIM SET |
| 28 |
NSS |
NOT SOLD SEPARATE, Insert |
| 29 |
NSS |
NOT SOLD SEPARATE, Decal-G/H Pinion Ident. |
| 30 |
8M0150151 |
FLO TORQUE III KIT |
| 31 |
NSS |
NOT SOLD SEPARATE, Adaptor |
| 32 |
NSS |
NOT SOLD SEPARATE, Lock Nut |
▶Ignition Components (14 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
880891T14 |
ECU, Engine Control Unit |
| 2 |
10-804270 |
BOLT, (M6 x 28) |
| 3 |
25-881304 |
GROMMET |
| 4 |
23-804344003 |
BUSHING |
| 5 |
881346T |
RECTIFIER/REGULATOR ASSEMBLY |
| 6 |
10-853536 |
BOLT, (M6 x 25) |
| 7 |
10-804604 |
BOLT, (M6 x 20) |
| 8 |
300-8M0123821 |
COIL, Ignition |
| 9 |
339-8M0121257 |
COIL, Ignition |
| 10 |
881345 |
PLATE |
| 11 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 12 |
10-853536 |
BOLT, (M6 x 25) |
| 13 |
54-804276 |
CLAMP |
| 14 |
54-804277 |
CLAMP |
▶Intake (34 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881440T04 |
INTAKE ASSEMBLY |
| 1 |
880886T |
MANIFOLD |
| 2 |
25-881513 |
O-RING |
| 3 |
17-881512 |
PIN, Dowel |
| 4 |
10-881507 |
BOLT, (M6 x 25) |
| 5 |
881441T4 |
THROTTLE BODY ASSEMBLY |
| 6 |
24-881444 |
SPRING |
| 7 |
10-881510 |
BOLT, (M8 x 70) |
| 8 |
12-881508 |
WASHER |
| 9 |
881441T3 |
THROTTLE BODY ASSEMBLY |
| 10 |
10-881442 |
SCREW |
| 11 |
24-881444 |
SPRING |
| 12 |
10-881443 |
SCREW |
| 13 |
881514 |
LINK JOINT |
| 14 |
881515 |
LINK JOINT |
| 15 |
11-83763M |
NUT |
| 16 |
880884T |
SENSOR, Throttle |
| 17 |
25-881504 |
O-RING |
| 18 |
10-881502002 |
SCREW |
| 19 |
12-881450 |
WASHER |
| 20 |
881516 |
BRACKET |
| 21 |
10-881971A1 |
SCREW |
| 22 |
881511 |
HOSE |
| 23 |
881446T |
BODY |
| 24 |
881447T |
CONTROL VALVE |
| 25 |
25-881448 |
O-RING |
| 26 |
10-881449002 |
SCREW, (M4 x 12) |
| 27 |
12-881450 |
WASHER |
| 28 |
35-881501T |
FILTER |
| 29 |
880885T |
SENSOR, Pressure |
| 30 |
10-881509 |
SCREW, (M5 x 15) |
| 31 |
10-881505 |
BOLT, (M6 x 24) |
| 32 |
10-881506 |
BOLT, (M6 x 60) |
| 33 |
84-881517T1 |
HARNESS ASSEMBLY |
▶Intake Silencer (22 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881421T04 |
POWERHEAD ASSEMBLY |
| 1 |
881436T |
SILENCER, Intake |
| 2 |
880882T |
THERMOSENSOR |
| 3 |
25-881437 |
O-RING |
| 4 |
10-804165 |
BOLT, (M6 x 16) |
| 5 |
10-881816 |
BOLT, (M8 x 20) |
| 6 |
881439 |
BRACKET |
| 7 |
8M0059034 |
BRACKET |
| 8 |
10-881435 |
BOLT, (M6 x 20) |
| 9 |
892849 |
INDUCTION SILENCER Comment: SN# 0T980000 & Up |
| 10 |
881269 |
BRACKET |
| 11 |
10-8M0204741 |
SCREW, (M6 x 20) Stainless Steel |
| 12 |
17-804160 |
PIN |
| 13 |
27-881433 |
GASKET |
| 14 |
32-804162 |
BREATHER PIPE |
| 15 |
54-804163 |
CLAMP |
| 16 |
10-804602 |
BOLT, (M6 x 12) |
| 17 |
54-804089 |
CLIP |
| 18 |
56762 |
TIE STRAP, (4.00 Inches) Comment: SN# 0T980000 & Up |
| 19 |
10-881438 |
BOLT, (M6 x 105) |
| 20 |
10-881431 |
BOLT, (M8 x 40) |
| 21 |
881822 |
SCREEN |
▶Intake and Exhaust Valves (26 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881421T04 |
POWERHEAD ASSEMBLY |
| 1 |
57-804145 |
V BELT |
| 2 |
10-804143001 |
BOLT, (M10 x 35) |
| 3 |
43-804142T |
GEAR, Driven |
| 4 |
26-804144001 |
SEAL, Oil |
| 5 |
17-804141 |
PIN, Dowel |
| 6 |
2407-8M0057172 |
CAMSHAFT |
| 7 |
2407-804139T |
CAMSHAFT |
| 8 |
804128T |
VALVE, Intake |
| 9 |
804129T |
VALVE, Exhaust |
| 10 |
804130 |
SEAT |
| 11 |
26-804136 |
SEAL |
| 12 |
26-804137 |
SEAL |
| 13 |
24-804131 |
SPRING, Valve |
| 14 |
804132 |
RETAINER |
| 15 |
28-804135 |
COTTER VALVE |
| 16 |
804138T |
LIFTER, Valve |
| 17 |
15-80460880 |
SHIM Comment: (2.975) |
| 18 |
804149 |
PLATE, Valve |
| 19 |
28-804153 |
KEY |
| 20 |
804146 |
TENSIONER |
| 21 |
10-804150 |
BOLT, (M10 x 45) |
| 22 |
24-804147 |
SPRING |
| 23 |
32-804148 |
HOSE |
| 24 |
43-804151T |
GEAR, Drive |
| 25 |
11-881314003 |
NUT, (M40) (40MM) |
▶Oil Pump (22 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
25-62705001 |
O-RING |
| 2 |
17-41275M |
PIN, Dowel |
| 3 |
881900T03 |
MOUNT |
| 4 |
10-898487 |
BOLT, (M12 x 175) |
| 5 |
12-32834 |
WASHER, Neoprene |
| 6 |
12-8M0204648 |
WASHER, (1.5 x 3.05 x 0.13) Stainless Steel |
| 7 |
11-896963 |
NUT, (M12) |
| 8 |
10-4010750 |
SCREW, (M8 x 50) |
| 9 |
858579T3 |
PUMP, Oil |
| 10 |
10-8M0052670 |
BOLT, (M6 x 45) |
| 11 |
26-804349 |
SEAL |
| 12 |
888834T01 |
BRACKET ASSEMBLY, Shift Linkage |
| 13 |
10-42975 |
DRIVE SCREW |
| 14 |
10-82130020 |
SCREW, (M6 x 20) |
| 15 |
889530 |
CUP, Barrel Retainer (LARGE) |
| 16 |
98889 |
LATCH |
| 17 |
824015 |
CUP, Barrel Retainer, Barrel Retainer (SMALL) |
| 18 |
889529 |
LATCH |
| 19 |
87-879996A2 |
SWITCH |
| 20 |
10-88075020 |
SCREW, (M3 x 20) |
| 21 |
8M0043168 |
SEAL |
| 22 |
17-23784 |
PIN, Dowel |
▶Oil Tank (21 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
1200-879844T08 |
TANK, Oil |
| 2 |
19299A1 |
VENT ASSEMBLY |
| 3 |
21-64871 |
VALVE |
| 4 |
87-856156T04 |
SWITCH |
| 5 |
12-72761 |
WASHER, (.203 x .562 x .060) Stainless Steel |
| 6 |
10-58376 |
SCREW, (.164-18 x .375) |
| 7 |
23-883821 |
BUSHING |
| 8 |
25-883820001 |
GROMMET Comment: SN# 0T980000 & Up |
| 9 |
35-883037T |
FILTER |
| 10 |
883044001 |
COVER, To Air Compressor |
| 11 |
10-883075 |
SCREW, (#10-16 x 1.25) |
| 12 |
19-854310 |
PLUG |
| 13 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 14 |
25-879857 |
BOOT |
| 15 |
36-8M0073266 |
CAP |
| 16 |
25-26318T |
O-RING |
| 17 |
887776002 |
CHAIN |
| 18 |
11-65110 |
NUT |
| 19 |
10-82446035 |
SCREW, (M8 x 35) |
| 20 |
12-4002318 |
WASHER |
| 21 |
37-881865 |
DECAL, Caution-Start in Gear Comment: (Start In Gear) |
▶Oiling System (14 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
32-88306955 |
HOSE, (.125 x 25.00 Inches) |
| 2 |
32-88104441 |
TUBING, (18.00 Inches Bulk) (Cut to 13 Inches |
| 3 |
32-88104441 |
TUBING, (18.00 Inches Bulk) (Cut to 13-1/2 Inches) |
| 4 |
32-88104441 |
TUBING, (18.00 Inches Bulk) (Cut to 18 Inches) |
| 5 |
32-82381455 |
TUBING, (25.00 Inches Bulk) (Cut to 3-1/4 Inches |
| 6 |
32-82381455 |
TUBING, (25.00 Inches Bulk) (Cut to 7 Inches |
| 7 |
35-875284T01 |
FILTER, Oil - In Line |
| 8 |
56762 |
TIE STRAP, (4.00 Inches) |
| 9 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 10 |
32-828547412 |
CONDUIT, (10.00 Inches Bulk) (Cut to 6 Inches |
| 11 |
8M0214940 |
TIE STRAP, (5.50 Inches) |
| 12 |
8M0185614 |
PUMP ASSEMBLY, Oil |
| 13 |
10-81893420 |
SCREW, (M8 x 20) |
| 14 |
32-88104441 |
TUBING, (18.00 Inches Bulk) (Cut to 8 Inches |
▶Poppet/Thermostat Mounting (16 parts)
| Ref |
OEM Part # |
Part Name |
| 0 |
891767A07 |
POWERHEAD ASSEMBLY Comment: 90/115 |
| 1 |
884389 |
POPPET |
| 2 |
812887002 |
DIAPHRAGM Comment: SN# 0T932791 & Up |
| 3 |
12-94182 |
WASHER |
| 4 |
10-69570 |
SCREW, (#10-16 x .750) (10-16 x 3/4) |
| 5 |
24-892321 |
SPRING |
| 6 |
8M0036780 |
COVER |
| 7 |
10-82127335 |
SCREW, (M8 x 35) |
| 8 |
27-879855001 |
GASKET Comment: SN# 0T832041 & Up |
| 9 |
27-8M0204714 |
GASKET Comment: SN# 0T961337 & Up |
| 10 |
833072004 |
THERMOSTAT, 62°C (143°F) Comment: SN# 0T980000 & Up |
| 11 |
54-814634 |
CLAMP |
| 12 |
10-82130012 |
SCREW, (M6 x 12) |
| 13 |
8M0148668 |
SENSOR ASSEMBLY |
| 14 |
25-896699 |
O-RING, (.351 x .072) |
| 15 |
23-892265 |
SPACER |
▶Power Trim Components (19 parts)
| Ref |
OEM Part # |
Part Name |
| - |
25-893914A02 |
O-RING KIT (COMPLETE TRIM) |
| 1 |
8M0171821 |
SHOCK ROD KIT |
| 2 |
25-8M0171819 |
O-RING KIT, Rebuild |
| 3 |
8M0171822 |
PISTON ASSEMBLY, Memory |
| 4 |
893916A01 |
CYLINDER ASSEMBLY |
| 5 |
893905A02 |
VALVE KIT, Trim Limit |
| 6 |
893906A02 |
PUMP ASSEMBLY |
| 7 |
893907A02 |
MOTOR KIT |
| 8 |
22-8134351 |
PLUG |
| 9 |
893929A01 |
MANUAL RELEASE ASSEMBLY |
| 10 |
893909A02 |
MANIFOLD KIT |
| 11 |
10-809876A1 |
SCREW KIT (MOTOR) |
| 12 |
88238A18 |
CABLE ASSEMBLY |
| 13 |
809877A1 |
DRIVESHAFT/SEAL KIT |
| 14 |
35-893912A02 |
FILTER KIT |
| 15 |
893913A02 |
POPPET KIT |
| 16 |
17-821539 |
PIN, Trilobe |
| 17 |
17-818898 |
PIN, Anchor |
| 18 |
99625002 |
SHAFT Comment: SN# 0T928910 & Up |
▶Powerhead Gasket Set Components (2 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-858732T02 |
GASKET SET, Powerhead |
| 0 |
25-8M0052669 |
O-RING, Fuel Pump Comment: (Not used for this application) |
▶Reed Block (34 parts)
| Ref |
OEM Part # |
Part Name |
| 0 |
891767A07 |
POWERHEAD ASSEMBLY Comment: 90/115 |
| 1 |
42881A1 |
SHIFT RAIL ASSEMBLY |
| 2 |
14-42981 |
TAB WASHER |
| 3 |
10-40001134 |
SCREW, (M8 x 25) |
| 4 |
988851 |
SLIDE |
| 5 |
11-401386 |
NUT, (M6) Stainless Steel |
| 6 |
12-35459 |
WASHER |
| 7 |
11-401386 |
NUT, (M6) Stainless Steel |
| 8 |
27-430075 |
GASKET |
| 9 |
1169-858552T2 |
CAP ASSEMBLY, Lower End |
| 10 |
21-426585 |
CHECK VALVE |
| 11 |
26-419533 |
SEAL, Oil |
| 12 |
25-89224 |
O-RING |
| 13 |
10-4010825 |
SCREW, (M10 x 25) Hex Flange - Stainless Steel |
| 14 |
879839A00 |
PLATE ASSEMBLY, Reed Adaptor |
| 15 |
27-879840 |
GASKET |
| 16 |
22-768431 |
FITTING |
| 17 |
879841A03 |
COVER |
| 18 |
27-879843 |
GASKET |
| 19 |
10-82127345 |
SCREW, (M8 x 45) |
| 20 |
10-82127335 |
SCREW, (M8 x 35) |
| 21 |
828623T4 |
REED BLOCK |
| 22 |
27-880122 |
GASKET |
| 23 |
10-4007420 |
SCREW, (M6 x 20) |
| 24 |
854445 |
SENSOR, MAP |
| 25 |
884522 |
BRACKET, MAP Sensor |
| 26 |
10-82130016 |
SCREW, (M6 x 16) |
| 27 |
8M0148668 |
SENSOR ASSEMBLY |
| 28 |
25-896699 |
O-RING, (.351 x .072) |
| 29 |
84-88439A26 |
CABLE ASSEMBLY, Battery - Negative |
| 30 |
10-81893414 |
SCREW, (M8 x 14) |
| 31 |
12-36001 |
WASHER |
| 32 |
54-889559 |
CLAMP |
| 33 |
12-69056 |
WASHER, (.255 x .620 x .030) Stainless Steel |
▶Sensors (17 parts)
| Ref |
OEM Part # |
Part Name |
| - |
881421T04 |
POWERHEAD ASSEMBLY |
| 1 |
804295T |
THERMOSENSOR |
| 2 |
804296 |
RETAINER |
| 3 |
10-811188T |
BOLT, (M6 x 16) |
| 4 |
27-8042971 |
GASKET |
| 5 |
54-83577M |
CLAMP |
| 6 |
10-84088M |
SCREW, (M6 x 10) |
| 7 |
881366 |
PLATE |
| 8 |
10-804602 |
BOLT, (M6 x 12) |
| 9 |
8042941 |
PLATE |
| 10 |
10-811188T |
BOLT, (M6 x 16) |
| 11 |
84-881364T05 |
HARNESS ASSEMBLY |
| 12 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 13 |
56762 |
TIE STRAP, (4.00 Inches) |
| 14 |
87-8043071 |
SWITCH, Oil Pressure |
| 15 |
84-881367A1 |
LEAD WIRE |
| 16 |
10-804604 |
BOLT, (M6 x 20) |
▶Service/Support Material (1 parts)
| Ref |
OEM Part # |
Part Name |
| 0 |
92-8M0078625 |
OIL-10W30 |
▶Starter Motor (32 parts)
| Ref |
OEM Part # |
Part Name |
| - |
50-881368T2 |
STARTER MOTOR ASSEMBLY |
| 1 |
804314T |
STATOR |
| 2 |
804313T |
ARMATURE |
| 3 |
881369T1 |
HOLDER ASSEMBLY, Brush |
| 4 |
804316 |
BRUSH SET |
| 5 |
24-804317 |
SPRING |
| 6 |
881370T |
BRACKET |
| 7 |
10-804337 |
SCREW, (M4 x 16) |
| 8 |
10-804335 |
THRU BOLT, (M6 x 120) |
| 9 |
804321T1 |
GEAR KIT |
| 10 |
804322 |
CLUTCH |
| 11 |
12-804330 |
WASHER KIT |
| 12 |
804324 |
BRACKET |
| 13 |
804326 |
RING GEAR |
| 14 |
27-804327 |
GASKET |
| 15 |
31-804325 |
BEARING |
| 16 |
804323 |
SHAFT, Pinion |
| 17 |
43-804329001 |
IDLER GEAR |
| 18 |
804328 |
BRACKET |
| 19 |
804331T |
COVER |
| 20 |
10-804336 |
BOLT, (M6 x 52) |
| 21 |
804319 |
PINION |
| 22 |
804320 |
STOP SET, Pinion |
| 23 |
804332 |
LEVER KIT |
| 24 |
804334 |
COVER |
| 25 |
881371T1 |
RELAY, Starter |
| 26 |
10-804605 |
BOLT, (M8 x 45) |
| 27 |
881373 |
TERMINAL |
| 28 |
13-881377 |
LOCKWASHER |
| 29 |
11-82382M |
NUT |
| 30 |
11-881372 |
NUT |
| 31 |
881374 |
COVER |
▶Steering Handle Kit (38 parts)
| Ref |
OEM Part # |
Part Name |
| - |
816366A32 |
STEERING HANDLE KIT |
| NS |
22-8M0169589 |
FITTING, Grease |
| 1 |
12020A3 |
HANDLE ASSEMBLY, Steering Arm |
| 2 |
23-42992T02 |
BUSHING |
| 3 |
48414 |
HOUSING |
| 4 |
48519 |
PLATE |
| 5 |
27-48518 |
GASKET |
| 6 |
10-878609 |
SCREW, (#10-16 x .600) |
| 7 |
10-878608 |
SCREW, (#10-16 x .500) |
| 8 |
54-889729 |
CLAMP |
| 9 |
10-40007112 |
SCREW, (M5 x 40) |
| 10 |
10-32,11-816874 |
WING NUT, |
| 11 |
87-823609A15 |
SWITCH KIT, Stop - Throttle Handle |
| 12 |
87-8M0104612 |
SWITCH ASSEMBLY, Stop |
| 13 |
NSS |
NOT SOLD SEPARATE, Insulator |
| 14 |
12018A4 |
TUBE ASSEMBLY, Throttle |
| 15 |
NSS |
NOT SOLD SEPARATE, Drive Wheel |
| 16 |
NSS |
NOT SOLD SEPARATE, Roll Pin |
| 17 |
10-62568 |
SCREW, (#10-16 x .375) |
| 18 |
8M0221732 |
GRIP |
| 19 |
54-648552 |
CLIP |
| 20 |
11-40140 |
NUT, (M10) |
| 21 |
8885241 |
CONDUIT, (9.03 Inches) |
| 22 |
895665 |
GUIDE TUBE |
| 23 |
89578 |
BARREL, Throttle Acutator |
| 24 |
10-32,10-824081 |
SET SCREW, |
| 25 |
12019003 |
CABLE ASSEMBLY |
| 26 |
8M0204660 |
GUIDE, Cable |
| 27 |
20007 |
ANCHOR, Cable End |
| 28 |
8-32,10-8M0204644 |
SET SCREW, |
| 29 |
10-823567105 |
SCREW, (M10 x 105) Hex Flange - Stainless Steel |
| 30 |
48416 |
CAP |
| 31 |
12-4002319 |
WASHER |
| 32 |
12-12024 |
WASHER, (.402 x .787 x .039 Bellevi) |
| 33 |
23-146011 |
SPACER |
| 34 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 35 |
NSS |
NOT SOLD SEPARATE, Decal-Throttle |
| 36 |
25-889724 |
GROMMET, Hose Cable |
▶Steering Handle Kit Components (51 parts)
| Ref |
OEM Part # |
Part Name |
| - |
816366A32 |
STEERING HANDLE KIT |
| 0 |
8949112 |
KEY, Ignition (2F) Comment: (2F) |
| 1 |
816366T10 |
HANDLE, Bracket |
| 2 |
10-881261 |
SCREW, (.313-24 x 3.50) |
| 3 |
14-42981 |
TAB WASHER |
| 4 |
822263 |
SPACER |
| 5 |
84-12649A4 |
HARNESS ASSEMBLY |
| 6 |
87-88107A5 |
SWITCH KIT, Key Comment: (See Chart Below for Keys) |
| 7 |
11-879755 |
NUT, Special - Black Nylon Comment: (Black Nylon) |
| 8 |
13541 |
PLUG, Male |
| 9 |
121051 |
GROMMET |
| 10 |
19-889730 |
PLUG |
| 11 |
8M0032846 |
RETAINER, Brass |
| 12 |
8158041 |
COVER |
| 13 |
10-878608 |
SCREW, (#10-16 x .500) |
| 14 |
87-11083A4 |
SWITCH ASSEMBLY, Stop |
| 15 |
15920Q54 |
LANYARD ASSEMBLY |
| 16 |
84-11149A3 |
CABLE ASSEMBLY |
| 17 |
889528T01 |
HORN ASSEMBLY |
| 18 |
87-18286A19 |
SWITCH KIT, Trim (25.00 Feet), Trim |
| 19 |
87-8M0052927 |
SWITCH |
| 20 |
10-12110 |
SCREW, (#6-32 x .750) |
| 21 |
54-648551 |
CLAMP |
| 22 |
10-878608 |
SCREW, (#10-16 x .500) |
| 23 |
10-849838 |
SCREW, (.375-24 x 1.250) |
| 24 |
11-8M0204726 |
NUT, (.375-24) Stainless Steel |
| 25 |
48419T01 |
ROD END |
| 26 |
495637 |
ROD, Shift |
| 27 |
23-26856 |
BUSHING |
| 28 |
12-35950 |
WASHER, (.273 x .437 x .031) Stainless Steel |
| 29 |
18-25191 |
COTTER PIN |
| 30 |
8163677 |
LEVER, Shift |
| 31 |
16-8M0034452 |
STUD, (.375-24 x 1.125) |
| 32 |
98530 |
KNOB |
| 33 |
12016A2 |
DETENT/SPRING KIT |
| 34 |
23-8159831 |
BUSHING |
| 35 |
12-823970 |
WASHER |
| 36 |
12-824610 |
WASHER, Plastic |
| 37 |
12-814803 |
WASHER |
| 38 |
14-8158051 |
TAB WASHER |
| 39 |
10-4000357 |
SCREW, (M8 x 45) |
| 40 |
56-52148A08 |
CO PILOT ASSEMBLY |
| 41 |
52148002 |
PILOT ROD, (15.00 Inches) |
| 42 |
11-52155A1 |
NUT ASSEMBLY |
| 43 |
10-36137 |
SCREW, (.250-28 x 1.00) |
| 44 |
821621 |
KNOB, Prong |
| 45 |
873491 |
ROD |
| 46 |
23-26841 |
BUSHING |
| 47 |
12-8M0042642 |
WASHER, (.323 x .563 x .063) Stainless Steel |
| 48 |
11-826709111 |
NUT, (.312-24) Stainless Steel |
| 49 |
11-64015 |
NUT, (.250-20) |
▶Swivel Bracket and Steering Arm (24 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
1400-8M0220957 |
SWIVEL BRACKET |
| 2 |
26-87735 |
SEAL, Oil (LOWER) |
| 3 |
23-818764 |
BUSHING |
| 4 |
25-8M0214926 |
O-RING |
| 5 |
23-816039 |
SPACER |
| 6 |
22-8M0169589 |
FITTING, Grease |
| 7 |
23-821207 |
BUSHING |
| 8 |
10-64014 |
SCREW, (.250-28 x .500) |
| 9 |
99661A35 |
SWIVEL PIN ASSEMBLY |
| 10 |
92876A12 |
LINK ROD ASSEMBLY |
| 11 |
10-849838 |
SCREW, (.375-24 x 1.250) |
| 12 |
11-8M0204726 |
NUT, (.375-24) Stainless Steel |
| 13 |
12-37828 |
WASHER, (.390 x .625 x .062) Stainless Steel |
| 14 |
42961A06 |
YOKE ASSEMBLY, Bottom |
| 15 |
53-67684 |
RING, Retaining |
| 16 |
12-816432 |
THRUST WASHER |
| 17 |
NSS |
NOT SOLD SEPARATE, Decal-Serial Overlaminate |
| 18 |
11288001 |
BUMPER, Bottom Yoke Comment: (SALTWATER) SN# 0T980000 & Up |
| 19 |
NSS |
NOT SOLD SEPARATE, Decal-Serial Number |
| 20 |
821400A2 |
SENDER KIT, Power Trim |
| 21 |
84-11149A58 |
CABLE ASSEMBLY |
| 22 |
10-852368 |
SCREW, (#10-24 x .750) |
| 23 |
10,13-26996 |
LOCKWASHER, Stainless Steel |
| 24 |
12-89302 |
WASHER, (.203 x .406 x .040) |
▶Throttle Body (30 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
880129T02 |
THROTTLE BODY ASSEMBLY Comment: (115) |
| 2 |
891770 |
RETAINER |
| 3 |
10-891771 |
SCREW |
| 4 |
26-891772 |
SEAL |
| 5 |
26-891772002 |
SEAL Comment: (Use with Oetiker Clamp) |
| 6 |
54-804842001 |
CLAMP, Oetiker |
| 7 |
10-891771001 |
SCREW |
| 8 |
12-891773 |
WASHER |
| 9 |
12-891773001 |
WASHER |
| 10 |
23-891774 |
BUSHING |
| 11 |
853659A01 |
LEVER KIT, Throttle |
| 12 |
858851A03 |
LEVER ASSEMBLY, Throttle |
| 13 |
10,13-69432 |
LOCKWASHER, External |
| 14 |
12-881992 |
WASHER, Spool |
| 15 |
12-881991 |
WASHER, Cupped |
| 16 |
10-889354 |
SCREW, Special |
| 17 |
677483 |
ROLLER |
| 18 |
891775 |
BRACKET |
| 19 |
10-1993716 |
SCREW, (M6 x 16) |
| 20 |
8819881 |
CABLE |
| 21 |
891776 |
CAM |
| 22 |
23-421621 |
BUSHING |
| 23 |
12-35462 |
WASHER, (.2656 x .625 x .0625) Stainless Steel |
| 24 |
10-4000333 |
SCREW, (M6 x 40) |
| 25 |
881967 |
COUPLER |
| 26 |
8M6005165 |
INDICATOR, Throttle Position |
| 27 |
10-891771002 |
SCREW |
| 28 |
892623001 |
INSERT Comment: (90) |
| 29 |
54-889691 |
CLAMP, Oetiker |
| 30 |
32-828547253 |
CONDUIT, (.250 Inside Diameter x 3.00 Feet Bulk), Cut to 13 Inches |
▶Throttle Lever and Linkage (13 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
878550 |
LEVER, Throttle |
| 2 |
12-84974M |
WASHER |
| 3 |
13-81868M |
WAVE WASHER |
| 4 |
11-8528162 |
NUT |
| 5 |
23-881378 |
COLLAR |
| 6 |
12-94524M |
WASHER |
| 7 |
24-804343 |
SPRING |
| 8 |
878548 |
LEVER, Throttle Control |
| 9 |
12-84974M |
WASHER |
| 10 |
13-81868M |
WAVE WASHER |
| 11 |
10-881375 |
BOLT, (M6 x 30) |
| 12 |
12-35459 |
WASHER |
| 13 |
18-82053M |
PIN, Hair |
▶Tools 1 (27 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
91-8M0161873 |
HOLDER TOOL, Flywheel |
| 2 |
91-83164M |
FLYWHEEL PULLER |
| 3 |
91-99379 |
TIMING LIGHT |
| 4 |
91-890451 |
ADAPTOR TOOL, Direct Voltage |
| 5 |
91-850439T1 |
TESTER, Eight Chamber |
| 6 |
91-892647A01 |
MULTI-METER KIT, DMT 2004 Comment: SN# 0T980000 & Up |
| 7 |
91-881825 |
HARNESS ASSEMBLY, Crank Position Sensor Test |
| 8 |
91-875216 |
HOLDER TOOL, Brush |
| 9 |
91-881824004 |
HARNESS ASSEMBLY, Stator Coil Test |
| 10 |
91-881827 |
HARNESS ASSEMBLY, Throttle Position Test |
| 11 |
91-881826 |
HARNESS ASSEMBLY, Ignition Coil Test |
| 12 |
91-8098712 |
VACUUMMATE TOOL, Carburetor Tuner |
| 13 |
91-881833A03 |
GAUGE KIT, Air/Fuel Pressure Comment: SN# 0T980000 & Up |
| 14 |
91-881834A1 |
GAUGE |
| 15 |
NSS |
NOT SOLD SEPARATE, Might Vac Vacuum Gauge Comment: (OBTAIN LOCALLY) |
| 16 |
99056A1 |
MALFUNCTION INDICATOR LAMP |
| 17 |
91-881828 |
STARBIT TOOL KIT |
| 18 |
91-804774001 |
REMOVER/INSTALLER TOOL, Valve Guide |
| 19 |
91-804775 |
REAMER TOOL, Valve Guide |
| 20 |
91-809494A1 |
COMPRESSOR TOOL, Valve Spring |
| 21 |
NSS |
NOT SOLD SEPARATE, Valve Seat Cutter Kit Comment: (OBTAIN LOCALLY) |
| 22 |
91-802653Q02 |
WRENCH, Oil Filter Comment: SN# 0T980000 & Up |
| 23 |
FT2997 |
COMPRESSOR TOOL, Piston Ring |
| 24 |
91-24697 |
EXPANDER TOOL, Piston Ring |
| 25 |
91-804770A1 |
HOLDER TOOL, Crankshaft |
| 26 |
91-875215A1 |
INSTALLER TOOL, Driveshaft Bushing |
| 27 |
91-881847T |
SOCKET, (76 mm Deep) |
▶Tools 2 (33 parts)
| Ref |
OEM Part # |
Part Name |
| - |
91-881828 |
STARBIT TOOL KIT |
| 28 |
91-74951 |
SPANNER WRENCH |
| 29 |
NSS |
NOT SOLD SEPARATE, Lock-Ring Pliers Comment: (SNAP-ON SRP-4) |
| 30 |
NSS |
NOT SOLD SEPARATE, Expanding Rod Comment: (SNAP-ON CG41-11) |
| 31 |
NSS |
NOT SOLD SEPARATE, Collet Comment: (SNAP-ONG CG41-12) |
| 32 |
91-63209 |
HEAT LAMP |
| 33 |
91-12349A05 |
TOOL, Pinion Locating Comment: SN# 0T980000 & Up |
| 34 |
91-13945 |
INSTALLATION TOOL, Bearing |
| 35 |
91-13949 |
DRIVER TOOL, Oil Seal |
| 36 |
91-14308T02 |
TOOL KIT, Bearing Race |
| 37 |
91-14309T02 |
INSTALLATION TOOL, Bearing |
| 38 |
91-14310T1 |
WEAR SLEEVE INSTALLATION TOOL |
| 39 |
91-14311A04 |
TOOL, Preload Comment: SN# 0T980000 & Up |
| 40 |
91-15755T |
MANDREL |
| 41 |
91-196601 |
INDICATOR TOOL, Backlash |
| 42 |
91-31106T |
MANDREL, Bearing Driver Cup |
| 43 |
91-31108T |
DRIVER, Oil Seal |
| 44 |
91-36569T |
DRIVE HEAD TOOL |
| 45 |
91-804776A1 |
HOLDING TOOL, Driveshaft |
| 46 |
91-31229 |
SHAFT |
| 47 |
11-24156 |
NUT, (.625-18) |
| 48 |
91-34569A1 |
PULLER ASSEMBLY, Slide Hammer |
| 49 |
91-37323 |
DRIVER ROD TOOL, Needle Bearings |
| 50 |
91-37241 |
PULLER PLATE |
| 51 |
91-37350T |
MANDREL |
| 52 |
91-46086A1 |
PULLER JAW ASSEMBLY |
| 53 |
91-58222A1 |
DIAL INDICATOR TOOL |
| 54 |
91-8M0053505 |
INDICATOR TOOL, Backlash |
| 55 |
91-85716 |
PULLER TOOL |
| 56 |
91-83155 |
ADAPTER KIT, Dial Indicator |
| 57 |
91-83165T |
PULLER ASSEMBLY |
| 58 |
91-856875A1 |
INSTALLATION TOOL, Bearing |
| 59 |
91-877321A1 |
INSTALLATION TOOL, Bearing |
▶Top Cowl (27 parts)
| Ref |
OEM Part # |
Part Name |
| 0 |
37-881650A03 |
DECAL SET Comment: (Gray) |
| 1 |
4021-827328T10 |
TOP COWL ASSEMBLY Comment: (Silver) |
| 2 |
821256T2 |
INLET, Air - Silver Comment: (Silver) |
| 3 |
10-82130016 |
SCREW, (M6 x 16) |
| 4 |
859356A02 |
SOUND BLANKET KIT |
| 5 |
NSS |
NOT SOLD SEPARATE, Sound Blanket-Port |
| 6 |
NSS |
NOT SOLD SEPARATE, Sound Blanket-Starboard |
| 7 |
NSS |
NOT SOLD SEPARATE, Sound Blanket-Back |
| 8 |
19-823865 |
CAP PLUG |
| 9 |
831207A16 |
HANDLE |
| 10 |
23-812707 |
BUSHING |
| 11 |
23-831214 |
SPACER |
| 12 |
13-12134 |
WASHER, Wave |
| 13 |
8M0001081 |
CAM Comment: SN# 0T980000 & Up |
| 14 |
12-8M0214930 |
WASHER |
| 15 |
10-1993716 |
SCREW, (M6 x 16) |
| 16 |
8M0036792 |
BRACKET, Front |
| 17 |
815477 |
BUMPER, Latch |
| 18 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 19 |
11-401366 |
NUT, (M6) Stainless Steel |
| 20 |
53-8237951 |
RING, Retaining |
| 21 |
8M0207770 |
ROLLER |
| 22 |
8155381 |
PIN, Roll |
| 23 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 24 |
11-401366 |
NUT, (M6) Stainless Steel |
| 25 |
47341A11 |
ROPE AND HANDLE KIT, Manual Starting |
| 26 |
50-12066Q10 |
ROPE |
▶Transom Bracket (29 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
3426-828334T02 |
BRACKET, Transom Comment: (STARBOARD) |
| 2 |
3425-828333T07 |
BRACKET ASSEMBLY, Transom Comment: (PORT) |
| 3 |
22-8M0169588 |
FITTING, Grease Comment: (PORT) |
| 4 |
826125A1 |
TILT TUBE Comment: (STAINLESS STEEL) |
| 5 |
11-826135 |
NUT, (1.00-14) Nylon Insert Comment: (Use With Stainless Steel Tilt Tube) |
| 6 |
25-45711 |
O-RING, (.612 x .103) |
| 7 |
13-88750 |
WASHER |
| 8 |
11-826164 |
NUT, (.875-14) Comment: (Use With Stainless Steel Tilt Tube) |
| 9 |
10-8M0149747 |
SCREW, (.500-20 x 4.500) |
| 10 |
12-8M0204665 |
WASHER, (.530 x .870 x .105) Stainless Steel |
| 11 |
12-8M0204648 |
WASHER, (1.5 x 3.05 x 0.13) Stainless Steel |
| 12 |
11-82671117 |
NUT, (.500-20) |
| 13 |
24-830899 |
SPRING, Tension |
| 14 |
8M0109798 |
LEVER ASSEMBLY, Tilt Lock |
| 15 |
23-65830 |
NYLINER |
| 16 |
24-830900 |
SPRING, Compression |
| 17 |
99633 |
KNOB |
| 18 |
17-99615 |
PIN, Groove |
| 19 |
17-893709 |
PIN |
| 20 |
8M0086406 |
BRACKET, Anchor |
| 21 |
10-858771 |
SCREW, (M10 x 30) |
| 22 |
12-4002319 |
WASHER |
| 23 |
11-40114 |
NUT, (M10 x 1.5) |
| 24 |
97-818298Q1 |
ANODE KIT |
| 25 |
10-8M0204707 |
SCREW, (M6 x 25) |
| 26 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 27 |
54-22740 |
CLIP |
| 28 |
8M0084613 |
C WASHER |
| 29 |
10-878609 |
SCREW, (#10-16 x .600) |
▶Vapor Separator (35 parts)
| Ref |
OEM Part # |
Part Name |
| - |
880133T12 |
VAPOR SEPARATOR ASSEMBLY |
| 1 |
889317T1 |
COVER KIT |
| 2 |
NSS |
NOT SOLD SEPARATE, Seat |
| 3 |
889318001 |
PLATE, Baffle |
| 4 |
10-883223 |
SCREW, (M6 x 16) |
| 5 |
27-889319 |
GASKET |
| 6 |
22-883556 |
FITTING |
| 7 |
25-8M0062785 |
O-RING |
| 8 |
22-889329 |
FITTING |
| 9 |
19-883208 |
PLUG |
| 10 |
35-8M0122423 |
FILTER, Fuel |
| 11 |
889320A1 |
FLOAT KIT |
| 12 |
F10064 |
SHAFT |
| 13 |
888725T02 |
PUMP ASSEMBLY, Fuel - High Pressure |
| 14 |
8M6000589 |
SLEEVE |
| 15 |
25-8893162 |
O-RING |
| 16 |
26-889321 |
SEAL |
| 17 |
889328 |
RETAINER |
| 18 |
1395-9643 |
SCREW |
| 19 |
888733T02 |
PUMP ASSEMBLY, Boost |
| 20 |
25-889322 |
GROMMET |
| 21 |
25-889316 |
O-RING |
| 22 |
26-8M6001413 |
SEAL |
| 23 |
889324T03 |
BOWL KIT |
| 24 |
84-889325A02 |
WIRE |
| 25 |
NSS |
NOT SOLD SEPARATE, Check Valve |
| 26 |
22-855424011 |
FITTING |
| 27 |
889326A1 |
VALVE KIT, Inlet |
| 28 |
10-889327A1 |
SCREW, Drian |
| 29 |
25-8893161 |
O-RING |
| 30 |
8M0214989 |
SENSOR, Water |
| 31 |
22-782792 |
FITTING, Elbow 45 Degree (1.25) |
| 32 |
25-627021 |
O-RING, (.301 x .070) |
| 33 |
889430 |
INSERT |
| 34 |
54-816311T |
TIE STRAP, (8.00 Inches) |
▶Vapor Separator/Fuel Rail Mounting (10 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
16-8M0063255 |
STUD, (M10 x 91) |
| 2 |
11-826292 |
NUT, (M10) Brass/Nickel Plated |
| 3 |
8M6001744 |
INJECTOR ASSEMBLY, Air Comment: SN# 0T980000 & Up |
| 4 |
12-828694A1 |
WASHER ASSEMBLY, Cupped |
| 5 |
23-883050 |
SPACER |
| 6 |
25-855362001 |
GROMMET Comment: SN# 0T980000 & Up |
| 7 |
12-4002318 |
WASHER |
| 8 |
10-82446060 |
SCREW, (M8 x 60) |
| 9 |
10-82446035 |
SCREW, (M8 x 35) |
| 10 |
23-855364 |
BUSHING |
▶Water Hoses (5 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
35-8348084 |
STRAINER |
| 2 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 3 |
32-883060001 |
HOSE Comment: SN# 0T980000 & Up |
| 4 |
32-85833939 |
HOSE, (17.00 Inches Bulk) (Cut to 10-1/2 Inches) |
| 5 |
32-85833939 |
HOSE, (17.00 Inches Bulk) (Cut to 6-1/2 Inches) To Telltale |
100-Hour / Annual Service Checklist
Regular maintenance keeps your Mercury 115 EFI (4-STROKE) running reliably season after season. Most of these tasks can be performed with basic tools and the factory service manual.
- Replace water pump impeller and inspect wear plate
- Change engine oil and oil filter (check drain plug washer)
- Replace spark plugs and check ignition timing
- Drain and refill lower unit gear oil; inspect for water contamination
- Inspect fuel lines, primer bulb, and fuel filter for deterioration
- Check and replace sacrificial anodes (zinc or aluminum)
- Inspect propeller for damage; check shaft seal and cotter pin
- Check valve clearance (refer to service manual for specifications)
- Lubricate all grease points (steering, tilt tube, shift linkage)
- Inspect control cables and throttle/shift linkage for smooth operation
-
Pro Tip: Always flush the engine with fresh water after saltwater use — even a quick 10-minute flush significantly extends component life.
-
Pro Tip: Use fuel stabilizer in the tank before winter storage, and fog the cylinders to prevent internal corrosion during extended periods of non-use.