🔎 Mercury 60 (4-STROKE)(4 CYL.) Reference Library — Exploded parts diagrams (31 diagrams), specifications, common issues, and maintenance checklist.
The Mercury 60 (4-STROKE)(4 CYL.) is a 4-Stroke, Inline 4-Cylinder, EFI, SOHC outboard motor. Suited for bay boats, pontoons, and center-console fishing boats requiring reliable mid-range power.
Quick Reference Specifications
| Specification |
Value |
| Engine Type |
4-Stroke, Inline 4-Cylinder, EFI, SOHC |
| Horsepower |
60 HP |
| Displacement |
995 cc |
| Bore x Stroke |
65 mm x 75 mm |
| Spark Plug (Type & Gap) |
NGK IZFR6F-11 |
| Engine Oil Capacity |
3.0 L (3.17 quart) |
| Recommended Engine Oil |
SAE 25W-40 Mercury FourStroke Oil |
| Gear Case Oil Capacity |
440 mL (14.9 fl oz) |
| Idle Speed (in gear) |
650 ± 50 RPM (in gear) |
| Full Throttle RPM Range |
5500-6000 |
| Fuel |
Unleaded Gasoline, 87 Octane min. |
Always verify specifications against your owner's manual for your specific serial number range.
Common Issues & Recommended Parts
Below are common maintenance scenarios for the Mercury 60 (4-STROKE)(4 CYL.):
-
Water Pump / Overheating: If the tell-tale stream is weak or absent, the water pump impeller likely needs replacement. Inspect annually or every 100 hours. → Recommended: Water Pump Impeller Kit
-
Engine Oil / Maintenance Light: 4-stroke engines require regular oil and filter changes. Use marine-grade oil rated for your engine. Change every 100 hours or annually. → Recommended: Oil Filter, Engine Oil
-
Fuel Injector Issues (EFI models): Rough idle or misfires may indicate clogged fuel injectors. Use fuel stabilizer and clean injectors periodically. → Recommended: Fuel Injector, Fuel Filter
-
Gear Case Oil Leak: Check lower unit seals if gear oil appears milky (water contamination). Replace seals and gaskets during lower unit service. → Recommended: Lower Unit Seal Kit, Drain Plug Gaskets
-
Anode Corrosion: Inspect sacrificial anodes regularly, especially in saltwater. Replace when 50% depleted to protect against galvanic corrosion. → Recommended: Zinc/Aluminum Anode Kit
Parts Diagrams & OEM Part Numbers
Expand the sections below to view detailed exploded parts diagrams and find the exact OEM replacement components for your Mercury 60 (4-STROKE)(4 CYL.).
▶ACCESSORIES (1 parts)
| Ref |
OEM Part # |
Part Name |
| - |
12092A18 |
EXTENSION KIT, Driveshaft - 5 Inch Comment: (BIGFOOT) |
▶ADAPTOR PLATE (25 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-859352A01 |
GASKET SET |
| 1 |
8M0162935 |
DIPSTICK |
| 2 |
825989003 |
DIPSTICK TUBE |
| 3 |
8560552 |
SEAL |
| 4 |
8289151 |
HEAT SHIELD |
| 5 |
17-23784 |
PIN, Dowel |
| 6 |
22-629101 |
FITTING, Elbow - 90 Degree (.125-27) |
| 7 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 8 |
26-66301 |
SEAL, Oil |
| 9 |
23-859594 |
BUSHING |
| 10 |
22-384073 |
PLUG, Pipe (.500-14) |
| 11 |
825228A17 |
ADAPTOR PLATE KIT |
| 12 |
19-822464 |
PLUG |
| 13 |
19-48323 |
PLUG |
| 14 |
25-845746 |
O-RING |
| 15 |
10-8M0204741 |
SCREW, (M6 x 20) Stainless Steel |
| 16 |
8M0210772 |
BODY, Oil Pressure Relief Comment: (DESIGN II) |
| 17 |
893765 |
PLATE, Oil Pickup-Top |
| 18 |
32-854793 |
HOSE, Oil Pickup |
| 19 |
893700 |
BAFFLE |
| 20 |
54-855228 |
CLAMP |
| 21 |
10-4007455 |
SCREW, (M6 x 50) |
| 22 |
856592 |
DEFLECTOR, Oil Comment: (DESIGN I) |
| 23 |
8M0210772 |
BODY ASSEMBLY, Oil Pressure Relief Comment: (DESIGN I) |
| 24 |
27-8M0213113 |
GASKET |
▶BOTTOM COWL (18 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
4020-826277T1 |
BOTTOM COWL Comment: (LONG-PORT) |
| 2 |
4020-826278T7 |
BOTTOM COWL Comment: (LONG-STBD.) |
| 3 |
10-82684430 |
SCREW, (M6 x 30) |
| 4 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 5 |
825238002 |
SEAL |
| 6 |
12-855576 |
WASHER |
| 7 |
27-855627 |
GASKET |
| 8 |
10-82684460 |
SCREW, (M6 x 60) |
| 9 |
22-827948 |
FITTING |
| 10 |
826273001 |
BOOT |
| 11 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 12 |
825782F1 |
LEVER, Cowl Latch |
| 13 |
23-812707 |
BUSHING |
| 14 |
13-12134 |
WASHER, Wave |
| 15 |
893766 |
LATCH HOOK |
| 16 |
10-1993716 |
SCREW, (M6 x 16) |
| 17 |
25-19565002 |
GROMMET |
| 18 |
87-8M0235191 |
SWITCH, Trim |
▶CAMSHAFT (11 parts)
| Ref |
OEM Part # |
Part Name |
| - |
893505T01 |
CYLINDER HEAD ASSEMBLY |
| 1 |
400-8M0183247 |
CAMSHAFT |
| 2 |
857087T1 |
PUMP ASSEMBLY, Oil |
| 3 |
25-857096 |
O-RING |
| 4 |
NSS |
NOT SOLD SEPARATE |
| 5 |
25-857094 |
O-RING |
| 6 |
25-857093 |
O-RING |
| 7 |
10-875206 |
SCREW, (M6 x 16) |
| 8 |
10-4000333 |
SCREW, (M6 x 40) |
| 9 |
17-878183 |
PIN, Dowel |
| 10 |
17-826149 |
PIN |
▶CARBURETOR (36 parts)
| Ref |
OEM Part # |
Part Name |
| - |
8542561 |
REPAIR KIT, Carburetor Comment: (1 Per Carburetor) |
| 1 |
3329-857102T4 |
CARBURETOR Comment: (BOTTOM) |
| 2 |
10-854246 |
SCREW |
| 3 |
854245 |
PLATE |
| 4 |
27-8542572 |
GASKET |
| 5 |
854254T3 |
ENRICHENER |
| 6 |
NSS |
NOT SOLD SEPARATE |
| 7 |
854255 |
PLATE |
| 8 |
19-880814 |
CAP |
| 9 |
10-880841 |
SCREW, Adjusting |
| 10 |
25-880842 |
O-RING |
| 11 |
24-880815 |
SPRING |
| 12 |
803912 |
JET (SLOW) |
| 13 |
25-880843 |
O-RING |
| 14 |
19-880844 |
PLUG |
| 15 |
98,803915 |
JET (MAIN) |
| 16 |
8039142 |
MAIN NOZZLE |
| 17 |
854247 |
VALVE, Float |
| 18 |
8542531 |
FLOAT |
| 19 |
17-8542581 |
PIN, Float |
| 20 |
10-880845 |
SCREW |
| 21 |
27-8542573 |
GASKET |
| 22 |
8039171 |
FLOAT BOWL Comment: (CENTERS/BOTTOM) |
| 23 |
10-8542463 |
SCREW |
| 24 |
10-8542464 |
SCREW, Drain |
| 25 |
12-8542591 |
WASHER |
| 26 |
10-803925 |
SCREW, Synchronization Comment: (TOP/CENTERS) |
| 27 |
24-880846 |
SPRING Comment: (TOP/CENTERS) |
| 28 |
24-803923 |
SPRING Comment: (TOP/CENTERS) |
| 29 |
10-803913 |
SCREW Comment: (BOTTOM) |
| 30 |
24-854249 |
SPRING Comment: (BOTTOM) |
| 31 |
24-880847 |
SPRING |
| 32 |
8542511 |
PLUNGER |
| 33 |
10-880848 |
SCREW |
| 34 |
NSS |
NOT SOLD SEPARATE |
| 35 |
880849 |
PLUNGER ROD |
▶CRANKSHAFT (13 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-859352A01 |
GASKET SET |
| 1 |
413-857077T02 |
CRANKSHAFT |
| 2 |
8M0151047 |
SEAL |
| 3 |
8M0151048 |
SEAL |
| 4 |
600-893530T01 |
CONNECTING ROD |
| 5 |
10-8M0049884 |
BOLT |
| 6 |
23-893630002 |
BEARING, Blue |
| 7 |
700-893524T02 |
PISTON, w/o Rings Comment: (.50MM Oversized)(Bare Piston) |
| 8 |
39-893525A03 |
RING, Piston (TOP) Comment: (.50MM Oversized) |
| 9 |
NSS |
NOT SOLD SEPARATE, Piston (SECOND) Comment: (.50MM Oversized) |
| 10 |
39-893950 |
RING, Oil |
| 11 |
41-893863 |
PIN, Piston |
| 12 |
40-825017 |
RETAINER |
▶CYLINDER BLOCK AND CRANKCASE (28 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-859352A01 |
GASKET SET |
| 1 |
800-893502T02 |
CYLINDER BLOCK |
| 2 |
17-825010 |
PIN, Dowel |
| 3 |
22-479452 |
PLUG |
| 4 |
22-384073 |
PLUG, Pipe (1/2-14) |
| 5 |
22-416223 |
PLUG, Pipe (.750-14) |
| 6 |
23-893631002 |
BEARING, Blue |
| 7 |
822625 |
NIPPLE, (M20) |
| 8 |
10-82506182 |
SCREW, (M8 x 82) |
| 9 |
10-8M0205943 |
SCREW, (M6 x 35) |
| 10 |
27-8M0213112 |
GASKET |
| 11 |
35-8M0162829 |
FILTER, Oil |
| 12 |
27-8M0224375 |
GASKET |
| 13 |
8M0188836 |
COVER, Exhaust |
| 14 |
22-479452 |
PLUG |
| 15 |
14586 |
THERMOSTAT |
| 16 |
27-8M0204714 |
GASKET |
| 17 |
27-8M0177107 |
GASKET |
| 18 |
8M0188835 |
COVER |
| 19 |
10-8M0205943 |
SCREW, (M6 x 35) |
| 20 |
22-996642 |
FITTING, Elbow 90 Degree (.125-27 x .250) Nylon |
| 21 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 22 |
32-8M0108349 |
TUBING, (.312) (70.00 Inches Bulk) (Cut to 11 IN.) |
| 23 |
8M0214984 |
SENSOR ASSEMBLY, Temperature |
| 24 |
25-627021 |
O-RING, (.301 x .070) |
| 25 |
893697 |
LIFTING EYE |
| 26 |
10-857139 |
SCREW, (M8 x 35) |
| 27 |
NSS |
NOT SOLD SEPARATE |
▶CYLINDER HEAD (28 parts)
| Ref |
OEM Part # |
Part Name |
| - |
893505T01 |
CYLINDER HEAD ASSEMBLY |
| 1 |
893505T06 |
CYLINDER HEAD ASSEMBLY |
| 2 |
858266 |
GUIDE |
| 3 |
10-4000325 |
SCREW, (M6 x 8) |
| 4 |
12-859768 |
WASHER |
| 5 |
26-893549 |
SEAL, Oil |
| 6 |
22-875209 |
PIPE PLUG |
| 7 |
25-8M0011870 |
SEAL |
| 8 |
8M0174400 |
COVER |
| 9 |
NSS |
NOT SOLD SEPARATE |
| 10 |
858277 |
PLATE, Baffle |
| 11 |
10-4005685 |
SCREW, (M4 x 10) |
| 12 |
22-629101 |
FITTING, Elbow - 90 Degree (.125-27) |
| 13 |
27-8M0118179 |
GASKET |
| 14 |
10-8M0204741 |
SCREW, (M6 x 20) Stainless Steel |
| 15 |
10-82503395 |
SCREW, (M9 x 95) |
| 16 |
17-825010 |
PIN, Dowel |
| 17 |
859578A1 |
PLUG ASSEMBLY, Oil |
| 18 |
25-8M0204673 |
O-RING, (.921 x .139) |
| 19 |
NSS |
NOT SOLD SEPARATE, Decal |
| 20 |
NSS |
NOT SOLD SEPARATE, Decal |
| 21 |
NSS |
NOT SOLD SEPARATE, POWERHEAD ID |
| 22 |
826060 |
DIAPHRAGM |
| 23 |
877844 |
DASHPOT Comment: (NON HANDLE) |
| 24 |
10-40011126 |
SCREW, (M6 x 13) Stainless Steel |
| 25 |
32-77653101 |
HOSE, (48.00 Inches Bulk) (Cut to 19 IN.) |
| 26 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 27 |
10-893745025 |
SCREW, (M6 x 25) |
▶DRIVESHAFT HOUSING (26 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
1503-852421T07 |
HOUSING, Driveshaft |
| 2 |
825220T06 |
PIPE, Exhaust |
| 3 |
10-824459110 |
SCREW, (M8 x 110) Stainless Steel |
| 4 |
10-88960845 |
SCREW, (M8 x 45) |
| 5 |
8288181 |
PLUG, Drain |
| 6 |
27-8M0204692 |
GASKET |
| 7 |
826276 |
BUMPER |
| 8 |
8M0151042 |
GROMMET |
| 9 |
16-903501 |
STUD, (M10 x 100) Comment: (BIGFOOT) |
| 10 |
12-8M0214963 |
WASHER, (.406 x .750 x .105) Stainless Steel |
| 11 |
11-40140 |
NUT, (M10) |
| 12 |
32-897971A01 |
TUBE, Water |
| 13 |
54-828529 |
GUIDE |
| 14 |
8M0043364 |
BUMPER Comment: (LONG) |
| 15 |
42941001 |
SEAL, Water Tube |
| 16 |
893770 |
PLATE |
| 17 |
10-1993325 |
SCREW, (M10 x 25 MM) |
| 18 |
22-85822A7 |
SPEEDOMETER PICK UP |
| 19 |
22-85822T |
CONNECTOR, Straight |
| 20 |
22-8M0181450 |
FITTING |
| 21 |
23-813745 |
SPACER |
| 22 |
43585 |
COUPLING |
| 23 |
23-855623 |
BUSHING |
| 24 |
12-45176 |
WASHER, (.453 x .812 x .105) Stainless Steel |
| 25 |
11-40140 |
NUT, (M10) |
| 26 |
54-816311T |
TIE STRAP, (8.00 Inches) |
▶ELECTRICAL COMPONENTS (47 parts)
| Ref |
OEM Part # |
Part Name |
| - |
61-893678T03 |
POWERHEAD ASSEMBLY |
| 1 |
825096T01 |
RELAY |
| 2 |
8M0010250 |
BRACKET |
| 3 |
825074 |
SOLENOID PLATE |
| 4 |
11-401386 |
NUT, (M6) Stainless Steel |
| 5 |
84-88439A9 |
CABLE ASSEMBLY, Battery - Positive |
| 6 |
85-880786 |
BOOT, Insulator - Red |
| 7 |
84-93388A16 |
CABLE ASSEMBLY, (8.50 Inches) |
| 8 |
84-88439A4 |
CABLE ASSEMBLY, Battery - Negative |
| 9 |
50-893888T |
STARTER MOTOR ASSEMBLY (SEE BREAKDOWN ON STARTER MOTOR) |
| 10 |
10-40011153 |
SCREW, (M8 x 45) Stainless Steel |
| 11 |
87-8M0098207 |
PRESSURE SWITCH |
| 12 |
8M0082988 |
SENSOR |
| 13 |
10-40011107 |
SCREW, (M5 x 16) Stainless Steel |
| 14 |
10-82130025 |
SCREW, (M6 x 25) |
| 15 |
12-8M0214930 |
WASHER |
| 16 |
859224 |
PLATE |
| 17 |
856836001 |
RETAINER |
| 18 |
856040 |
BRACKET |
| 19 |
10-82129114 |
SCREW, (M6 x 14) |
| 20 |
92753 |
RETAINER |
| 21 |
23-856954 |
BUSHING |
| 22 |
25-8M0190980 |
GROMMET |
| 23 |
87843303S |
ECM, Engine Control Module |
| 24 |
23-8539201 |
BUSHING |
| 25 |
10-82129140 |
SCREW, (M6 x 40) |
| 26 |
33-827858Q |
SPARK PLUG, NGK-DPR6EA-9 |
| 27 |
339-859738T1 |
COIL ASSEMBLY, Ignition |
| 28 |
NSS |
NOT SOLD SEPARATE, Decal Comment: (COIL ID #1) |
| 29 |
NSS |
NOT SOLD SEPARATE, Decal Comment: (COIL ID #2) |
| 30 |
NSS |
NOT SOLD SEPARATE, Decal Comment: (COIL ID #3) |
| 31 |
NSS |
NOT SOLD SEPARATE, Decal Comment: (COIL ID #4) |
| 32 |
10-82684430 |
SCREW, (M6 x 30) |
| 33 |
84-857111T2 |
HARNESS ASSEMBLY, Engine Wiring |
| 34 |
88-812619 |
FUSE, Yellow - 20 Ampere (SFE) |
| 35 |
828054 |
COVER, Fuse |
| 36 |
84-852375A6 |
HARNESS ASSEMBLY, Extension Comment: (HANDLE) |
| 37 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 38 |
883071T1 |
REGULATOR, Voltage |
| 39 |
893771 |
BRACKET |
| 40 |
8308971 |
FOAM PAD |
| 41 |
10-8248329 |
SCREW, (M6 x 40) |
| 42 |
10-82129110 |
SCREW, (M6 x 10) |
| 43 |
10-8248324 |
SCREW, (M6 x 16) |
| 44 |
13541 |
PLUG, Male |
| 45 |
10-40011149 |
SCREW, (M8 x 25) Stainless Steel |
| 46 |
11-94330 |
NUT, (.250-20) Brass |
▶FLYWHEEL (21 parts)
| Ref |
OEM Part # |
Part Name |
| - |
893505T01 |
CYLINDER HEAD ASSEMBLY |
| 1 |
859284T2 |
FLYWHEEL COVER |
| 2 |
10-8248326 |
SCREW, (M6 x 25 MM) |
| 3 |
37-804655A01 |
DECAL, EPA Label Information Comment: (SEE NOTE) |
| 4 |
284-832010T32 |
FLYWHEEL |
| 5 |
8331045 |
GEAR, Driven |
| 6 |
NSS |
NOT SOLD SEPARATE, Decal |
| 7 |
NSS |
NOT SOLD SEPARATE, Decal |
| 8 |
NSS |
NOT SOLD SEPARATE, Decal |
| 9 |
11-893789 |
NUT |
| 10 |
12-893762 |
WASHER |
| 11 |
10-4013930 |
SCREW, (M5 x 30) |
| 12 |
398-852387T7 |
STATOR |
| 13 |
834838 |
LOAD RING |
| 14 |
833102T |
GEAR, Drive |
| 15 |
10-82761140 |
SCREW, (M10 x 40) |
| 16 |
12-4002320 |
WASHER |
| 17 |
28-91800 |
KEY, Woodruff |
| 18 |
28-893761 |
KEY |
| 19 |
8M0151040 |
BELT |
| 20 |
54-816311T |
TIE STRAP, (8.00 Inches) |
▶FUEL LINES (19 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
22-822771 |
CONNECTOR |
| 2 |
22-878404 |
FITTING, 45 Degree |
| 3 |
22-878593 |
Y-CONNECTOR |
| 4 |
54-878425 |
CLIP |
| 5 |
32-878181 |
HOSE |
| 6 |
32-85682239 |
TUBING, (17.00 Inches Bulk) (Cut to 3-1/2 IN) |
| 7 |
32-82381310 |
HOSE |
| 8 |
8566101 |
LINKAGE |
| 9 |
23-803896 |
BUSHING |
| 10 |
18-880850 |
COTTER PIN |
| 11 |
12-8542592 |
WASHER |
| 12 |
32-856607 |
HOSE |
| 13 |
32-856609 |
HOSE |
| 14 |
32-856611 |
HOSE and SLEEVE |
| 15 |
32-880773 |
HOSE |
| 16 |
32-856613 |
HOSE |
| 17 |
32-880772 |
HOSE |
| 18 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 19 |
56762 |
TIE STRAP, (4.00 Inches) |
▶FUEL PUMP (24 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-859352A01 |
GASKET SET |
| 1 |
35-877565T1 |
FILTER, Fuel |
| 2 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 3 |
32-8M0108355 |
HOSE, (57.00 Inches Bulk) (Cut to 14 IN.) |
| 4 |
32-8M0108355 |
HOSE, (57.00 Inches Bulk) (Cut to 19 IN.) |
| 5 |
22-8M0148585 |
CONNECTOR ASSEMBLY, Fuel |
| 6 |
826398T3 |
PUMP, Fuel |
| 7 |
10-809564 |
SCREW, (M5 x 35) |
| 8 |
809565 |
COVER |
| 9 |
8095611 |
DIAPHRAGM |
| 10 |
10-41889M |
SCREW, (M3 x 5) |
| 11 |
11-82537M |
NUT |
| 12 |
21-41888M |
CHECK VALVE |
| 13 |
8095612 |
DIAPHRAGM |
| 14 |
17-8095661 |
PIN |
| 15 |
24-809562 |
SPRING |
| 16 |
11-82388M |
NUT, (M5) |
| 17 |
24-8095621 |
SPRING |
| 18 |
8095631 |
PLUNGER |
| 19 |
25-8M0052669 |
O-RING |
| 20 |
10-82684430 |
SCREW, (M6 x 30) |
| 21 |
19-854310 |
PLUG |
| 22 |
54-8M0024808 |
J CLIP |
| 23 |
8M0007776 |
DEFLECTOR, Cowl |
▶GEAR HOUSING(DRIVESHAFT)(1.83:1 GEAR RATIO) (37 parts)
| Ref |
OEM Part # |
Part Name |
| - |
46-812966A12 |
REPAIR KIT, Water Pump |
| 1 |
1671-9760T42 |
GEAR HOUSING ASSEMBLY, Basic |
| 2 |
10-79953Q04 |
SCREW KIT, (.375-16 x .250) Drain |
| 3 |
10-79953Q04 |
SCREW KIT, (.375-16 x .250) Drain |
| 4 |
12-191833 |
WASHER |
| 5 |
17-8M0084244 |
PIN, Dowel - With Hole (.375 x .625) |
| 6 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) |
| 7 |
22-878089 |
PLUG, Pipe (.0625-27) |
| 8 |
31-812768 |
BEARING, Roller |
| 9 |
818226A1 |
SEAL/PLATE KIT |
| 10 |
NSS |
NOT SOLD SEPARATE |
| 11 |
43-859103T |
GEAR, Pinion - 12 Teeth |
| 12 |
11-55910 |
NUT, (.437-20) |
| 13 |
859607A1 |
SHIFT SHAFT ASSEMBLY |
| 14 |
53-29641 |
E RING |
| 15 |
23-813696A2 |
BUSHING ASSEMBLY |
| 16 |
25-45258 |
O-RING, (.987 x .103) |
| 17 |
26-8M0204708 |
SEAL, Oil |
| 18 |
45-859102 |
DRIVESHAFT, Long |
| 19 |
15-812770A1 |
SHIM SET |
| 20 |
31-8M0166756 |
BEARING ASSEMBLY, Roller |
| 21 |
NSS |
NOT SOLD SEPARATE |
| 22 |
11-8128201 |
NUT |
| 23 |
46-812966A7 |
BASE ASSEMBLY, Water Pump |
| 24 |
25-8M0204651 |
O-RING, (1.859 x .139) |
| 25 |
26-814669 |
SEAL, Oil |
| 26 |
26-814670 |
SEAL, Oil |
| 27 |
47-19453T |
IMPELLER |
| 28 |
28-8M0032831 |
KEY |
| 29 |
12-8M0204720 |
WASHER |
| 30 |
46-812966A12 |
PUMP ASSEMBLY, Water |
| 31 |
27-8M0224241 |
GASKET (LOWER) |
| 32 |
27-822189 |
GASKET, Upper Water Pump |
| 33 |
19700A2 |
FACE PLATE |
| 34 |
10-8248324 |
SCREW, (M6 x 16) |
| 35 |
760394 |
CAM, Shift Control |
| 36 |
8M0151045 |
COUPLER |
▶GEAR HOUSING(DRIVESHAFT)(2.31:1 GEAR RATIO) (43 parts)
| Ref |
OEM Part # |
Part Name |
| - |
47-8M0100526 |
REPAIR KIT, Water Pump Impeller |
| 1 |
1667-9011G59 |
GEAR HOUSING ASSEMBLY, Basic Comment: (BASIC) |
| 2 |
17-8M0084244 |
PIN, Dowel - With Hole (.375 x .625) (FRONT) |
| 3 |
43046 |
TUBE, Oiler |
| 4 |
10-79953Q04 |
SCREW KIT, (.375-16 x .250) Drain |
| 5 |
12-191833 |
WASHER |
| 6 |
17-43044 |
PIN, Dowel - Without Hole (.375 x .625) (REAR) |
| 7 |
31640T07 |
TRIM TAB |
| 8 |
10-825427 |
SCREW, (.437-14 x 1.250) Stainless Steel |
| 9 |
12-451761 |
WASHER, (.453 x .812 x .105) Black Oxide |
| 10 |
43040T1 |
CARRIER ASSEMBLY |
| 11 |
NSS |
NOT SOLD SEPARATE |
| 12 |
97-826134Q |
ANODE |
| 13 |
11-401386 |
NUT, (M6) Stainless Steel |
| 14 |
10-4000333 |
SCREW, (M6 x 40) |
| 15 |
43-44484T |
GEAR, Pinion (13 Teeth) |
| 16 |
11-35921 |
NUT, (.625-18) |
| 17 |
850307 |
CAM, Shift Control |
| 18 |
31-42677A1 |
BEARING ASSEMBLY, Tapered Roller |
| 19 |
15-44492A1 |
SHIM SET |
| 20 |
45-859105A1 |
DRIVESHAFT ASSEMBLY |
| 21 |
42461A1 |
SLEEVE/RING KIT |
| 22 |
NSS |
NOT SOLD SEPARATE |
| 23 |
43055A4 |
COVER ASSEMBLY, Water Pump |
| 24 |
27-430331 |
GASKET |
| 25 |
27-8M0214931 |
GASKET |
| 26 |
26-43036 |
SEAL, Oil (LOWER) |
| 27 |
26-43035 |
SEAL, Oil (UPPER) |
| 28 |
27-8172771 |
GASKET |
| 29 |
817275A2 |
HOUSING KIT, Upper Water Pump |
| 30 |
8M0204709 |
FACEPLATE |
| 31 |
10-8M0214957 |
SCREW, (M6 x 30) |
| 32 |
8M0204658 |
SEAL |
| 33 |
28-8M0204723 |
KEY |
| 34 |
47-43026T2 |
IMPELLER |
| 35 |
10-8248326 |
SCREW, (M6 x 25 MM) |
| 36 |
853906A1 |
SHIFT SHAFT ASSEMBLY |
| 37 |
53-29641 |
E RING |
| 38 |
23-43052A4 |
BUSHING ASSEMBLY |
| 39 |
25-8M0204681 |
O-RING, (1.424 x .103) |
| 40 |
26-8M0204708 |
SEAL, Oil |
| 41 |
10-8248326 |
SCREW, (M6 x 25 MM) |
| 42 |
26-861415 |
FACE SEAL |
▶GEAR HOUSING(PROP SHAFT)(1.83:1 GEAR RATIO) (33 parts)
| Ref |
OEM Part # |
Part Name |
| - |
26-814669A2 |
SEAL KIT, Gear Housing |
| 1 |
1671-9760T42 |
GEAR HOUSING ASSEMBLY, Basic |
| 37 |
15-812769A1 |
SHIM SET |
| 38 |
31-8M0103476 |
BEARING ASSEMBLY, Tapered Roller |
| 39 |
NSS |
NOT SOLD SEPARATE |
| 40 |
43-859101T2 |
GEAR, Forward - 22 Teeth |
| 41 |
31-21739 |
BEARING, Roller |
| 42 |
8129291 |
FOLLOWER, Cam |
| 43 |
20843 |
SLIDE |
| 44 |
24-38114 |
SPRING |
| 45 |
52-813697T |
CLUTCH |
| 46 |
17-8M0020942 |
PIN, Cross |
| 47 |
24-815418 |
SPRING |
| 48 |
44-14493 |
PROPELLER SHAFT |
| 49 |
43-859104T |
GEAR, Reverse - 22 Teeth |
| 50 |
30-20839T |
BEARING, Ball |
| 51 |
8M0168900 |
CARRIER ASSEMBLY, Bearing |
| 52 |
25-815460 |
O-RING |
| 53 |
31-21700 |
BEARING, Needle |
| 54 |
26-8M0205511 |
SEAL, Oil |
| 55 |
26-8M0203757 |
SEAL, Oil |
| 56 |
10-85594030 |
SCREW, (M8 x 30) |
| 57 |
12-855941 |
WASHER, (.323 x .590 x .112) Stainless Steel |
| 58 |
8227731 |
INSERT, Threaded |
| 59 |
NSS |
NOT SOLD SEPARATE |
| 60 |
17264T2 |
TRIM TAB, Zinc |
| 61 |
10-4000377 |
SCREW, (M10 x 30) |
| 62 |
12-8M0214963 |
WASHER, (.406 x .750 x .105) Stainless Steel |
| 63 |
73345A1 |
THRUST HUB |
| 64 |
11-69578Q1 |
PROP NUT KIT |
| 65 |
14-8M0214942 |
TAB WASHER |
| 66 |
12-8M0214963 |
WASHER, (.406 x .750 x .105) Stainless Steel |
| 67 |
10-4000380 |
SCREW, (M10 x 45) |
▶GEAR HOUSING(PROP SHAFT)(2.31:1 GEAR RATIO) (36 parts)
| Ref |
OEM Part # |
Part Name |
| - |
26-43035A4 |
SEAL KIT, Gear Housing |
| 1 |
1667-9011G59 |
GEAR HOUSING ASSEMBLY, Basic |
| 2 |
31-30894A1 |
BEARING SET, Cup And Cone |
| 3 |
NSS |
NOT SOLD SEPARATE |
| 4 |
43-859472A3 |
GEAR ASSEMBLY, Forward - 30 Teeth |
| 5 |
31-30895T |
BEARING, Needle |
| 6 |
53-856823 |
RING, Retaining |
| 7 |
850315A1 |
FOLLOWER KIT, Cam |
| 8 |
30-44530 |
BALL |
| 9 |
NSS |
NOT SOLD SEPARATE |
| 10 |
24-850327 |
SPRING |
| 11 |
52-850048T |
CLUTCH |
| 12 |
17-8M0100263 |
PIN, Cross |
| 13 |
24-30893 |
SPRING |
| 14 |
44-8M0140445 |
PROPELLER SHAFT |
| 15 |
43-850034T |
GEAR, Reverse (30 Teeth) |
| 16 |
8M0168901 |
CARRIER ASSEMBLY, Bearing |
| 17 |
25-8M0214974 |
O-RING, (3.609 x .139) |
| 18 |
31-30956T |
BEARING, Needle |
| 19 |
26-8M0205728 |
SEAL, Oil (INNER) |
| 20 |
26-8M0205729 |
SEAL, Oil (OUTER) |
| 21 |
31-12578T |
BEARING, Roller |
| 22 |
12-12577 |
THRUST WASHER |
| 23 |
31-12576 |
BEARING, Thrust |
| 24 |
16-8M0034456 |
STUD, (M8 x 48) |
| 25 |
12-855941 |
WASHER, (.323 x .590 x .112) Stainless Steel |
| 26 |
11-401378 |
NUT, (M8) |
| 27 |
15-44491A1 |
SHIM SET |
| 28 |
8227731 |
INSERT, Threaded |
| 29 |
NSS |
NOT SOLD SEPARATE, Decal |
| 30 |
NSS |
NOT SOLD SEPARATE, Decal |
| 31 |
13191Q01 |
THRUST WASHER |
| 32 |
11-52707Q1 |
PROP NUT KIT, (.750-16) |
| 33 |
14-816629Q |
TAB WASHER |
| 34 |
10-4000380 |
SCREW, (M10 x 45) |
| 35 |
12-8M0214963 |
WASHER, (.406 x .750 x .105) Stainless Steel |
▶INTAKE (19 parts)
| Ref |
OEM Part # |
Part Name |
| - |
27-859352A01 |
GASKET SET |
| 1 |
10-82615890 |
SCREW, (M6 x 90) |
| 2 |
857105T |
INTAKE, Air |
| 3 |
25-8250572 |
O-RING |
| 4 |
857103T |
PLATE |
| 5 |
857104T1 |
ISOLATOR Comment: (40/50 HP) |
| 6 |
19-827633 |
PLUG |
| 7 |
857106A1 |
ATTENUATOR KIT, Sound Comment: (USE W/TAPERED BUSHING) |
| 8 |
23-856954 |
BUSHING Comment: (TAPERED) |
| 9 |
10-8M0204741 |
SCREW, (M6 x 20) Stainless Steel |
| 10 |
54-850181 |
TIE STRAP, (11.750 Inches) |
| 11 |
26-856128001 |
SEAL |
| 12 |
25-8250572 |
O-RING |
| 13 |
25-856525 |
O-RING |
| 14 |
17-23784 |
PIN, Dowel |
| 15 |
10-8248326 |
SCREW, (M6 x 25 MM) |
| 16 |
32-8M0182223 |
BREATHER HOSE |
| 17 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 18 |
37-881865 |
DECAL, Caution, Start In Gear |
▶INTAKE/EXHAUST VALVE (19 parts)
| Ref |
OEM Part # |
Part Name |
| - |
893505T01 |
CYLINDER HEAD ASSEMBLY |
| 1 |
8M0065029 |
VALVE, Exhaust |
| 2 |
832990T3 |
VALVE, Intake |
| 3 |
26-858271 |
SEAL |
| 4 |
24-893552 |
SPRING, Valve - Outer |
| 5 |
822650 |
RETAINER |
| 6 |
28-893554 |
KEY |
| 7 |
898821A01 |
ROCKER ARM |
| 8 |
10-825046 |
SCREW |
| 9 |
11-826150 |
NUT |
| 10 |
8570851 |
SHAFT, Rocker |
| 11 |
NSS |
NOT SOLD SEPARATE |
| 12 |
893560 |
BRACKET |
| 13 |
893561 |
BRACKET |
| 14 |
24-893562 |
SPRING |
| 15 |
10-875218 |
SCREW, (M8 x 23) |
| 16 |
27-893645 |
GASKET |
| 17 |
17-859575 |
PIN |
| 18 |
24-893563 |
SPRING, Overload |
▶LINKAGE(HANDLE) (32 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
10-40011158 |
SCREW, (M8 x 70) Stainless Steel |
| 2 |
10-8147763 |
SCREW, (M6 x 60) |
| 3 |
11-401196 |
NUT, (M6) |
| 4 |
42942 |
CAP |
| 5 |
822682A4 |
LEVER ASSEMBLY, Throttle |
| 6 |
23-825078 |
BUSHING |
| 7 |
10-8248326 |
SCREW, (M6 x 25 MM) |
| 8 |
858245 |
SHIFT GUIDE |
| 9 |
10-82239312 |
SCREW, (M5 x 12) |
| 10 |
858246 |
SHIFT SLIDE |
| 11 |
12016A2 |
DETENT/SPRING KIT |
| 12 |
NSS |
NOT SOLD SEPARATE |
| 13 |
858247 |
SHIFT ROD |
| 14 |
18-210711 |
COTTER PIN |
| 15 |
11-401386 |
NUT, (M6) Stainless Steel |
| 16 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 17 |
858248 |
SHIFT LINK |
| 18 |
23-48475 |
BUSHING |
| 19 |
850166T2 |
LEVER ASSEMBLY, Shift Shaft |
| 20 |
23-850165 |
BUSHING |
| 21 |
8535853 |
CAM, Throttle |
| 22 |
23-309772 |
SPACER |
| 23 |
12-4002314 |
WASHER |
| 24 |
10-40056107 |
SCREW, (M5 x 16) |
| 25 |
87-8M0052927 |
SWITCH |
| 26 |
824923 |
PLATE |
| 27 |
10-88075020 |
SCREW, (M3.5 x 20) Stainless Steel |
| 28 |
830294T1 |
BRACKET Comment: (HANDLE) |
| 29 |
877844 |
DASHPOT Comment: (NON-HANDLE) |
| 30 |
10-40011126 |
SCREW, (M6 x 13) Stainless Steel |
| 31 |
822682A4 |
LEVER, Throttle |
| 32 |
826587 |
RETAINER |
▶LINKAGE(REMOTE) (29 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
10-40011158 |
SCREW, (M8 x 70) Stainless Steel |
| 2 |
10-8147763 |
SCREW, (M6 x 60) |
| 3 |
11-401196 |
NUT, (M6) |
| 4 |
42942 |
CAP Comment: (50/60) |
| 5 |
822682A4 |
LEVER ASSEMBLY, Throttle |
| 6 |
883160 |
RETAINER |
| 7 |
23-825078 |
BUSHING |
| 8 |
822459 |
RETAINER |
| 9 |
8259571 |
LEVER, Shift |
| 10 |
827706A4 |
BRACKET |
| 11 |
98889 |
LATCH |
| 12 |
10-8248324 |
SCREW, (M6 x 16) |
| 13 |
23-15885 |
SLEEVE |
| 14 |
893777 |
SHIFT ROD |
| 15 |
8501631 |
GUIDE, Shift Rod |
| 16 |
893769A01 |
SHIFT LINK |
| 17 |
23-48475 |
BUSHING |
| 18 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 19 |
11-401386 |
NUT, (M6) Stainless Steel |
| 20 |
18-210711 |
COTTER PIN |
| 21 |
850166T2 |
LEVER ASSEMBLY, Shift Shaft |
| 22 |
23-850165 |
BUSHING |
| 23 |
8535853 |
CAM, Throttle |
| 24 |
23-309772 |
SPACER |
| 25 |
12-4002314 |
WASHER |
| 26 |
10-40056107 |
SCREW, (M5 x 16) |
| 27 |
881283F |
SPACER, Throttle Stop Comment: (40) |
| 28 |
822682A4 |
LEVER, Throttle |
| 29 |
826587 |
RETAINER |
▶POWER TRIM (27 parts)
| Ref |
OEM Part # |
Part Name |
| - |
84-826802T18 |
HARNESS/RELAY ASSEMBLY, Trim |
| 1 |
893943A01 |
SHOCK ROD KIT |
| 2 |
8M0171822 |
PISTON ASSEMBLY, Memory |
| 3 |
25-8M0171819 |
O-RING KIT, Rebuild |
| 4 |
NSS |
NOT SOLD SEPARATE |
| 5 |
893904T01 |
CYLINDER ASSEMBLY |
| 6 |
893944A01 |
VALVE KIT, Trim Limit Comment: (BIGFOOT) |
| 7 |
893906A02 |
PUMP ASSEMBLY |
| 8 |
893907A02 |
MOTOR KIT |
| 9 |
22-8134351 |
PLUG |
| 10 |
893929A01 |
MANUAL RELEASE ASSEMBLY |
| 11 |
893909A02 |
MANIFOLD KIT |
| 12 |
10-809876A1 |
SCREW KIT (MOTOR) |
| 13 |
809877A1 |
DRIVESHAFT/SEAL KIT |
| 14 |
35-893912A02 |
FILTER KIT |
| 15 |
893913A02 |
POPPET KIT |
| 16 |
88238A18 |
CABLE ASSEMBLY |
| 17 |
17-821539 |
PIN, Trilobe |
| 18 |
17-19607 |
PIN |
| 19 |
17-822869001 |
PIN |
| 20 |
84-826802T17 |
HARNESS ASSEMBLY, Trim |
| 21 |
8M0207773 |
RELAY ASSEMBLY |
| 22 |
828102 |
BRACKET |
| 23 |
25-818967 |
GROMMET |
| 24 |
23-8M0214955 |
BUSHING |
| 25 |
NSS |
NOT SOLD SEPARATE |
| 26 |
10-82684430 |
SCREW, (M6 x 30) |
▶SERVICE/SUPPORT MATERIAL (1 parts)
| Ref |
OEM Part # |
Part Name |
| - |
37-804655A02 |
DECAL, EPA Label Information Comment: (SEE NOTE) |
▶STARTER MOTOR (11 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
50-893888T |
STARTER MOTOR ASSEMBLY |
| 2 |
15384 |
THRU BOLT |
| 3 |
891752 |
DRIVE KIT |
| 4 |
8236386 |
ARMATURE |
| 5 |
68575T2 |
PINION |
| 6 |
8236392 |
DRIVE CAP |
| 7 |
8119013 |
CAP, Commutator |
| 8 |
898265016 |
BRUSH/SPRING KIT |
| 9 |
898265014 |
HOLDER |
| 10 |
F15158 |
SCREW |
| 11 |
37-8272822 |
DECAL, Warning, High Voltage |
▶STEERING ARM (30 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
11-896963 |
NUT, (M12) |
| 2 |
893773002 |
STRAP Comment: (DESIGN III)(THICK STRAP) |
| 3 |
8M0224385 |
MOUNT |
| 4 |
10-8M0204741 |
SCREW, (M6 x 20) Stainless Steel |
| 5 |
8M0156878 |
BUMPER |
| 6 |
53-89531 |
RING, Retaining |
| 7 |
8M0118183 |
ARM, Steering |
| 8 |
816667F1 |
BRACKET Comment: (NON-HANDLE) |
| 9 |
14-8M0009820 |
TAB WASHER Comment: (NON-HANDLE) |
| 10 |
10-4000377 |
SCREW, (M10 x 30) Comment: (NON-HANDLE) |
| 11 |
10-898835001 |
BOLT, (M12 x 154) |
| 12 |
23-8279971 |
SPACER |
| 13 |
8M0219909 |
SWIVEL TUBE |
| 14 |
84-88238T01 |
CABLE ASSEMBLY |
| 15 |
8M0207768 |
CABLE ASSEMBLY, Ground |
| 16 |
10-823567105 |
SCREW, (M10 x 105) Hex Flange - Stainless Steel |
| 17 |
893703 |
BRACKET |
| 18 |
10-878607 |
SCREW, (#10-16 x .375) Comment: (SELF-TAPPING) |
| 19 |
11-8M0204726 |
NUT, (.375-24) Stainless Steel Comment: (HANDLE) |
| 20 |
823792 |
LEVER Comment: (HANDLE) |
| 21 |
12-29330 |
WASHER Comment: (HANDLE) |
| 22 |
821961 |
ROD (THREADED) Comment: (HANDLE) |
| 23 |
821957 |
BRAKE PLATE Comment: (HANDLE) |
| 24 |
8165621 |
DISC Comment: (HANDLE) |
| 25 |
8M0007471 |
PLATE Comment: (HANDLE) |
| 26 |
8165621 |
DISC Comment: (HANDLE) |
| 27 |
10-768042 |
SHOULDER SCREW, Hex Comment: (HANDLE) |
| 28 |
12-4002321 |
WASHER, (12.80 mm x 24.0 mm x 2.4 mm) Stainless Steel Comment: (DESIGN I) |
| 29 |
893773002 |
STRAP Comment: (Qty. of 1 used on DESIGN I) |
| 30 |
12-20959 |
WASHER Comment: (DESIGN II) |
▶SWIVEL BRACKET (16 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
19608A14 |
ATTACHING KIT, Engine Steering Comment: (ELECTRIC NON HANDLE) |
| 2 |
10-823919 |
SCREW, (.375-24 x 1.500) Comment: (ELECTRIC NON HANDLE) |
| 3 |
12-8M0109680 |
WASHER, (.390 x .546 x .12) Comment: (ELECTRIC NON HANDLE) |
| 4 |
12-37828 |
WASHER, (.390 x .625 x .062) Stainless Steel Comment: (ELECTRIC NON HANDLE) |
| 5 |
11-8M0204726 |
NUT, (.375-24) Stainless Steel Comment: (ELECTRIC NON HANDLE) |
| 6 |
822397 |
PUCK Comment: (ELECTRIC NON HANDLE) |
| 7 |
23-8217711 |
BUSHING |
| 8 |
1401-850066T01 |
SWIVEL BRACKET |
| 9 |
23-19606 |
BEARING |
| 10 |
22-8M0169589 |
FITTING, Grease Comment: (QTY. OF 3 REQUIRED ON HANDLE VERSIONS) |
| 11 |
37-8237011 |
DECAL, Co-Pilot Comment: (HANDLE) |
| 12 |
NSS |
NOT SOLD SEPARATE, Decal |
| 13 |
23-821777 |
BUSHING (LOWER) |
| 14 |
26-8M0205512 |
SEAL |
| 15 |
10-40011149 |
SCREW, (M8 x 25) Stainless Steel Comment: (NON-HANDLE) |
| 16 |
8282451 |
SEAL Comment: (NON-HANDLE) |
▶TILLER HANDLE (38 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
822148T06 |
COVER KIT |
| 2 |
822150 |
PULLEY |
| 3 |
NSS |
NOT SOLD SEPARATE |
| 4 |
10-878608 |
SCREW, (#10-16 x .500) Comment: (SELF TAPPING) |
| 5 |
4324210 |
CABLE ASSEMBLY, Throttle (30.50 Inches) |
| 6 |
4324211 |
CABLE ASSEMBLY, Throttle (41.50 Inches) |
| 7 |
85-960099 |
SLEEVE, (12.00 Inches) |
| 8 |
10-82526225 |
SCREW, (M8 x 25 MM) |
| 9 |
8M0072298 |
COVER |
| 10 |
23-821477 |
BUSHING |
| 11 |
828813T1 |
ARM, Steering Handle |
| 12 |
822441 |
RETAINER |
| 13 |
10-40011107 |
SCREW, (M5 x 16) Stainless Steel |
| 14 |
10-8M0204707 |
SCREW, (M6 x 25) |
| 15 |
892995 |
LOCK, Throttle |
| 16 |
24-96203 |
SPRING |
| 17 |
821972T |
KNOB, Throttle |
| 18 |
8M0138696 |
TILLER TUBE |
| 19 |
37-8242004 |
DECAL |
| 20 |
821465 |
HANDLE, Throttle |
| 21 |
8M0221732 |
GRIP |
| 22 |
87-8M0104614 |
SWITCH, Stop |
| 23 |
823687 |
CLIP |
| 24 |
87-11083A31 |
SWITCH, Stop |
| 25 |
8M0032846 |
RETAINER, Brass |
| 26 |
821455A4 |
BRACKET, Tiller |
| 27 |
13-826792 |
WAVE WASHER |
| 28 |
23-821477 |
BUSHING |
| 29 |
12-827314 |
WASHER |
| 30 |
32-828547633 |
CONDUIT, (.620 Inside Diameter x 3.00 Feet Bulk) |
| 31 |
54-816311T |
TIE STRAP, (8.00 Inches) |
| 32 |
37-82409316 |
DECAL, F-N-R Shift |
| 33 |
15920Q54 |
LANYARD ASSEMBLY |
| 34 |
10-40011151 |
SCREW, (M8 x 35) Stainless Steel |
| 35 |
830180A01 |
HANDLE |
| 36 |
23-830181 |
BUSHING |
| 37 |
14-8M0009820 |
TAB WASHER |
| 38 |
10-82484890 |
SCREW, (M10 x 90) |
▶TOOLS (71 parts)
| Ref |
OEM Part # |
Part Name |
| - |
91-31229A7 |
PULLER KIT, Bearing |
| 1 |
44357Q2 |
FLUSHING ATTACHMENT |
| 2 |
802889Q1 |
PUMP, Crankcase Oil |
| 3 |
91-802653Q02 |
WRENCH, Oil Filter |
| 4 |
91-8M0161873 |
HOLDER TOOL, Flywheel |
| 5 |
91-83164M |
FLYWHEEL PULLER |
| 6 |
91-99379 |
TIMING LIGHT |
| 7 |
91-890451 |
ADAPTOR TOOL, Direct Voltage |
| 8 |
91-854009A3 |
TACH MULTI METER, DMT 2000 Digital |
| 9 |
91-823686A2 |
DIGITAL DIAGNOSTIC TESTER |
| 10 |
91-8226086 |
CARTRIDGE |
| 11 |
84-822560A7 |
HARNESS ASSEMBLY, Adaptor |
| 12 |
84-822560A10 |
HARNESS ASSEMBLY, Adaptor |
| 13 |
91-36392 |
GAUGE TOOL, Carburetor |
| 14 |
91-809495001 |
REMOVER TOOL, Valve Guide |
| 15 |
91-809496A1 |
INSTALLER TOOL, Valve Guide Bushing |
| 16 |
91-809497A1 |
REAMER TOOL, Valve Guide |
| 17 |
91-809494A1 |
COMPRESSOR TOOL, Valve Spring |
| 18 |
NSS |
NOT SOLD SEPARATE |
| 19 |
FT2997 |
COMPRESSOR TOOL, Piston Ring |
| 20 |
92-8M0071838 |
ANTI-CORROSION GREASE, 8 oz |
| 21 |
91-24697 |
EXPANDER TOOL, Piston Ring |
| 22 |
91-74951 |
SPANNER WRENCH |
| 23 |
91-822778A3 |
DOWN PRESSURE KIT |
| 24 |
91-63209 |
HEAT LAMP |
| 25 |
91-877321A1 |
INSTALLATION TOOL, Bearing |
| 26 |
91-804063 |
CLAMP TOOL, Tubing |
| 27 |
NSS |
NOT SOLD SEPARATE (P/N-CG-41-11) |
| 28 |
NSS |
NOT SOLD SEPARATE (P/N -CG-41-14) |
| 29 |
11-24156 |
NUT, (.625-18) |
| 30 |
12-34961 |
WASHER |
| 31 |
91-29310 |
PLATE |
| 32 |
91-31229 |
SHAFT |
| 33 |
91-36571T |
WRENCH TOOL, Driveshaft Bearing |
| 34 |
91-37323 |
DRIVER ROD TOOL, Needle Bearings |
| 35 |
91-15755T |
MANDREL |
| 36 |
91-36569T |
DRIVE HEAD TOOL |
| 37 |
91-27780 |
PULLER |
| 38 |
91-37241 |
PULLER PLATE |
| 39 |
91-37312T |
DRIVER HEAD TOOL |
| 40 |
91-817011T |
INSTALLER TOOL, Needle Bearing |
| 41 |
84-825003A1 |
CABLE ASSEMBLY, DDT, 10FT. |
| 42 |
91-8098712 |
VACUUMMATE, Carburetor |
| 43 |
91-817007T |
INSTALLER TOOL, Seal |
| 44 |
91-43506T |
RETAINING TOOL, Bearing |
| 45 |
91-817005 |
INSTALLER TOOL, Bearing |
| 46 |
91-817006 |
INSTALLER TOOL, Water Pump Base Seal |
| 47 |
91-817008A2 |
LOCATION TOOL, Pinion Gear |
| 48 |
91-817009T |
DRIVER TOOL, Bearing Cup |
| 49 |
91-12349A05 |
LOCATION TOOL, Pinion |
| 50 |
91-13945 |
INSTALLATION TOOL, Bearing |
| 51 |
91-13949 |
DRIVER TOOL, Oil Seal |
| 52 |
91-14308T02 |
RACE TOOL, Bearing |
| 53 |
91-14309T02 |
INSTALLATION TOOL, Bearing |
| 54 |
91-14310T1 |
WEAR SLEEVE INSTALLATION TOOL |
| 55 |
91-14311A04 |
PRE LOAD TOOL, Bearing |
| 56 |
91-196601 |
INDICATOR TOOL, Backlash |
| 57 |
91-31106T |
MANDREL, Bearing Driver Cup |
| 58 |
91-31108T |
DRIVER, Oil Seal |
| 59 |
91-34569A1 |
PULLER ASSEMBLY, Slide Hammer |
| 60 |
91-46086A1 |
PULLER JAW ASSEMBLY |
| 61 |
91-37350T |
MANDREL |
| 62 |
91-817070 |
HOLDING TOOL, Driveshaft |
| 63 |
91-58222A1 |
DIAL INDICATOR TOOL |
| 64 |
91-85716 |
PULLER TOOL |
| 65 |
91-83155 |
ADAPTER KIT, Dial Indicator |
| 66 |
91-83165T |
PULLER ASSEMBLY |
| 67 |
91-856875A1 |
INSTALLATION TOOL, Bearing |
| 68 |
91-817057A02 |
BACKLASH INDICATOR TOOL |
| 69 |
91-817058A1 |
DRIVER TOOL, Bearing |
| 70 |
91-877840A1 |
HOLDING TOOL, Driveshaft |
▶TRANSOM BRACKET (33 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
3418-822866T04 |
BRACKET ASSEMBLY, Transom Comment: (PORT) |
| 2 |
22-8M0169588 |
FITTING, Grease |
| 3 |
17-99604 |
PIN, Groove |
| 4 |
3418-822865T05 |
BRACKET, Transom Comment: (STARBOARD) |
| 5 |
893704T01 |
LEVER ASSEMBLY, Tilt Lock |
| 6 |
24-99622 |
SPRING |
| 7 |
23-65830 |
NYLINER |
| 8 |
24-812708 |
SPRING |
| 9 |
812709 |
KNOB |
| 10 |
17-99615 |
PIN, Groove |
| 11 |
12-19619 |
WASHER |
| 12 |
18486F5 |
BRACKET, Anchor |
| 13 |
97-818298Q1 |
ANODE KIT |
| 14 |
10-8M0204707 |
SCREW, (M6 x 25) |
| 15 |
12-8M0204649 |
WASHER, (.281 x .500 x .060) Stainless Steel |
| 16 |
10-4000354 |
SCREW, (M8 x 30) Comment: (30 MM) |
| 17 |
10-4000355 |
SCREW, (M8 x 35) Comment: (35 MM) |
| 18 |
13-400257 |
LOCKWASHER, (M8) |
| 19 |
11-401388 |
NUT, (M8) Stainless Steel |
| 20 |
8M0041938 |
TILT TUBE |
| 21 |
11-858869 |
NUT, (.875-14) |
| 22 |
19624A1 |
SEAL KIT Comment: (NON-HANDLE) |
| 23 |
25-29619 |
O-RING, (.583 x .103) Comment: (NON-HANDLE) |
| 24 |
23-78861 |
SPACER Comment: (NON-HANDLE) |
| 25 |
54-22740 |
CLIP |
| 26 |
8M0084613 |
C WASHER |
| 27 |
10-878609 |
SCREW, (#10-16 x .600) |
| 28 |
10-814259 |
SCREW, (.500-20 x 4.00) |
| 29 |
12-8M0204648 |
WASHER, (1.5 x 3.05 x 0.13) Stainless Steel |
| 30 |
11-82671117 |
NUT, (.500-20) |
| 31 |
10-4009040 |
SCREW, (M10 x 40) Stainless Steel |
| 32 |
12-4002319 |
WASHER |
| 33 |
11-40140 |
NUT, (M10) |
▶TRIM SWITCH KIT (8 parts)
| Ref |
OEM Part # |
Part Name |
| - |
87-18286A18 |
SWITCH KIT, Trim (10.00 Feet) |
| 1 |
18861 |
RETAINER |
| 2 |
814820 |
ADAPTOR |
| 3 |
NSS |
NOT SOLD SEPARATE |
| 4 |
88-8M0207796 |
FUSE, 20 Ampere |
| 5 |
84-95084A2 |
CABLE ASSEMBLY |
| 6 |
84-11149A2 |
CABLE ASSEMBLY, (6.00 Inches) |
| 7 |
10-813523 |
SCREW, (#10-16 x 2.25) |
▶Top Cowl (16 parts)
| Ref |
OEM Part # |
Part Name |
| 1 |
4019-825239T4 |
TOP COWL ASSEMBLY Comment: (SILVER) |
| 2 |
NSS |
NOT SOLD SEPARATE |
| 3 |
826291F1 |
LATCH Comment: (SILVER) |
| 4 |
10-8231871 |
SCREW, (M4 x 14.5) |
| 5 |
8,13-26995 |
LOCKWASHER, Stainless Steel |
| 6 |
11-8237515 |
NUT, (M4) |
| 7 |
8M0153618 |
SEAL |
| 8 |
825243A03 |
SOUND BLANKET KIT |
| 9 |
NSS |
NOT SOLD SEPARATE |
| 10 |
893763 |
BRACKET ASSEMBLY, Latch Roller |
| 11 |
10-4006731 |
SCREW, (M6 x 16) |
| 12 |
8M0038412 |
BRACKET |
| 13 |
10-8231871 |
SCREW, (M4 x 14.5) |
| 14 |
8,13-26995 |
LOCKWASHER, Stainless Steel |
| 15 |
11-8237515 |
NUT, (M4) |
| 16 |
47341A11 |
ROPE AND HANDLE KIT, Manual Starting |
100-Hour / Annual Service Checklist
Regular maintenance keeps your Mercury 60 (4-STROKE)(4 CYL.) running reliably season after season. Most of these tasks can be performed with basic tools and the factory service manual.
- Replace water pump impeller and inspect wear plate
- Change engine oil and oil filter (check drain plug washer)
- Replace spark plugs and check ignition timing
- Drain and refill lower unit gear oil; inspect for water contamination
- Inspect fuel lines, primer bulb, and fuel filter for deterioration
- Check and replace sacrificial anodes (zinc or aluminum)
- Inspect propeller for damage; check shaft seal and cotter pin
- Check valve clearance (refer to service manual for specifications)
- Lubricate all grease points (steering, tilt tube, shift linkage)
- Inspect control cables and throttle/shift linkage for smooth operation
-
Pro Tip: Always flush the engine with fresh water after saltwater use — even a quick 10-minute flush significantly extends component life.
-
Pro Tip: Use fuel stabilizer in the tank before winter storage, and fog the cylinders to prevent internal corrosion during extended periods of non-use.