Customer Service: info@jlm-marine.com
Free shipping. No Minimum Purchase
Flexible Rubber Water Pump Impeller 653-0001 – 6 Blade Neoprene 51 mm Pin Drive – Fits Johnson 09-810B, Yanmar
- $26.40
- $26.40
- Unit price
- per
Couldn't load pickup availability
Free Shipping
Free standard shipping on all orders
Worry-Free Returns
Learn More.
How to Match This Part
This is a flexible rubber raw water pump impeller for marine engine and generator sea water cooling pumps. It sits inside the pump housing behind the cover plate and is driven by a pin through a slotted shaft. It replaces the primary original part number Jabsco 653-0001, and is also supplied against Johnson 09-810B / 09-810B-1, JMP 7050-01, DJ Pump 08-39-0601, Yanmar 128990-42200 / 128397-42200 and Northern Lights 25-18325.
Match this part by checking your engine in this order:
1. Original impeller part number (stamped on the old impeller or listed in the pump section of your parts catalog)
2. Blade count on the old impeller (this listing is 6 blades)
3. Raw water pump model (cast or labelled on the pump body, for example Johnson F4B)
4. Engine or generator model code (on the identification plate)
Identify it physically before ordering. This impeller has six straight vanes moulded in black neoprene around a machined brass insert. DJ Pump publishes 51 mm diameter, 22 mm width and 12 mm (0.47 in.) bore. JMP 7050-01 is the same 51 × 22 mm envelope with a slotted-shaft pin drive. It is not interchangeable with the ten-blade Jabsco 18653-0001 / JMP 7070-01 of the same outside size, or with the smaller 9.5 mm Yanmar 104211-42070 impeller used on many Japanese-built 2GM / 3GM pumps.
- ✓ Primary OEM: Jabsco 653-0001
- ✓ Product form: 6-blade neoprene impeller, brass insert, 12 mm pin drive
- ✓ Fitment: part number, then blade count, then pump model
Part Number Cross-Reference
Use this table to confirm equivalent part numbers. Jabsco 653-0001-P is the genuine retail kit of 653-0001. This listing is the impeller only. Numbers marked as ten-blade cousins are on the source sheet for search, not as a substitute for this six-blade part.
| Type | Brand | Part Number | Notes |
|---|---|---|---|
| OEM | Jabsco Pump | 653-0001 | Primary 6-blade reference. 653-0001-P / 653-0001B are kit / pack numbers of the same impeller |
| OEM | Jabsco Pump | 18653-0001 | Source-sheet Jabsco number. JMP 7070-01 is the 10-blade 51 × 22 mm cousin. Count blades before ordering |
| OEM | Johnson Pump (SPX Flow) | 09-810B, 09-810B-1 | F4B sea water pump impeller. 09-810B-1 is the Johnson kit number |
| OEM | JMP Pump | 7050-01 | 6-blade bare impeller. JMP 7050-01K is a kit and is not this listing |
| OEM | JMP Pump | 7070-01 | 10-blade cousin (Excel 7070-01). Same envelope, ten vanes. Not this listing |
| OEM | DJ Pump | 08-39-0601 | Official DJ table: 6 blade, 51 × 22 × 12 mm, neoprene |
| OEM | Yanmar | 128990-42200, 128397-42200, X08810B | European / later GM and YM sea water pumps. X08810B is the source-sheet Yanmar alias. Not 104211-42070 |
| OEM | Northern Lights | 25-18325 | Generator impeller listed against 09-810B-1. Some NL gensets instead use 25-12009 (10-blade 18673-0001). Confirm the original number |
| OEM | Westerbeke | 34440, 034440 | JMP 7050-01 equivalent list |
| Aftermarket | Sierra | 23-3307 | JMP 7050-01 equivalent list |
| Other brand | Industry interchange | 888-1430 | Source-sheet other-brand number for this SKU |
Compatible Engine Models
Confirm the original impeller number. Many Yanmar 2GM / 3GM engines use the smaller 9.5 mm 104211-42070 impeller instead of this 51 mm part. Match 128990-42200 or 128397-42200 on the old impeller before ordering.
| Brand | Engine / Pump Model | Original Part No. | Notes |
|---|---|---|---|
| Johnson Pump | F4B | 09-810B, 09-810B-1 | 6-blade 12 mm pin-drive sea water pump |
| Yanmar | 2GMF, 3GMF, 2YM, 3YM (JMP JPR-YM08IH pump family); 2GM20-YEU / 3GM30-YEU when the original impeller is 128990-42200 | 128990-42200, 128397-42200 | Not Japanese-built 2GM / 3GM pumps that use 104211-42070 (9.5 mm shaft) |
| Westerbeke | Generator sets using impeller 34440 / 034440 (JMP lists 4.0/4.4/6.0 BCD and 4.4/7.7/8.0/11.0 WMD pump family) | 34440, 034440 | Match the original impeller number |
| Northern Lights | Generator sea water pump using impeller 25-18325 | 25-18325 | Some NL units need 25-12009 instead. Confirm the number on the old impeller |
Technical Specifications
| Specification | Value |
|---|---|
| Part type | Flexible rubber impeller, raw water / sea water cooling pump |
| Number of blades | 6 (this listing). The 10-blade 18653-0001 / 7070-01 is a different part |
| Impeller diameter (A) | 51 mm (2 in.) |
| Impeller width / depth (B) | 22 mm (7/8 in.) |
| Shaft bore diameter (C) | 12 mm (0.47 in.) |
| Insert / drive type | Slotted shaft, through-hole pin drive |
| Insert material | Machined brass |
| Vane material | Neoprene rubber |
Package Contents
This listing is for the impeller only, as shown in the product images. Please refer to the part number cross-reference table to confirm component details.
Cover plate gaskets, O-rings, cover screws and lubricant are not included. Genuine Jabsco 653-0001-P and JMP 7050-01K kits add those service parts. If your service procedure calls for a new cover seal, order it separately against your pump model.
Installation Guide
- 1 Stop the engine or generator, let it cool, and close the raw water seacock so water cannot enter the boat while the pump is open.
- 2 Remove the cover plate screws from the sea water pump and lift off the cover. Keep the screws and the old gasket together so you can compare the seal size when reassembling.
- 3 Note the drive pin orientation, then grip the brass insert of the old impeller with an impeller puller or two flat-blade screwdrivers and pull it straight off the shaft. Recover any broken vane pieces from the heat exchanger inlet before continuing.
- 4 Clean the housing bore and the wear plate, and inspect them for scoring. Apply a marine-grade impeller lubricant, glycerine or soapy water to the bore and the new vanes. Do not use petroleum-based grease, which attacks neoprene.
- 5 Align the slot in the brass insert with the drive pin on the 12 mm pump shaft, then press the impeller in while turning the shaft in the normal direction of rotation so all six vanes lay over the same way.
- 6 Refit the cover plate with a serviceable gasket, tighten the screws evenly in a crisscross pattern, open the seacock, then start the engine and confirm steady water discharge and no leaks at the cover.
Note: Professional installation is recommended to ensure safety and optimal performance.
Troubleshooting & FAQ
Important Notes
- Verify that the product images and specifications match your original part. If discrepancies exist, even if your model is listed, do not proceed with the purchase.
- This product is an aftermarket replacement part and is not an OEM component.
- The impeller is supplied on its own. Cover plate seals, gaskets and lubricant must be ordered separately if your service procedure requires them.
- Count the vanes. Ten-blade 18653-0001 / 7070-01 is a different part with the same outside size.
- Do not order this impeller for a Yanmar pump that uses 104211-42070 (9.5 mm shaft, smaller envelope).
- Never run the pump dry. Even a few seconds without water will damage the neoprene vanes.
- Professional installation is recommended to ensure safety and optimal performance.
Why Choose JLM MARINE?
- Quality Assured: As a trusted manufacturer for over 20 years, we supply top marine brands globally.
- Fast Global Shipping: Free delivery worldwide in 5–15 days.
- Direct from Manufacturer: Competitive pricing without compromising quality.
We can ship to virtually any address in the world with free shipping available for most regions.
For our typical US and Canadian customers , our shipping timeframes are as follows:
- Amazon FBA: orders will be delivered within 1-5 business days after placing the order (during certain special periods such as major promotions, Christmas, etc., the delivery time of Amazon FBA may be affected).
- US warehouse shipment: orders will be delivered within 5 days after placing the order.
- China warehouse shipment: orders will be delivered about 12 days after placing the order.
When you place an order, we will estimate shipping and delivery dates for you based on the availability of your items and the shipping options you choose. Depending on the shipping provider you choose, shipping date estimates may appear on the shipping quotes page.
Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.
Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.
As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.
We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.
Parts Finder
Use our Parts Finder to quickly locate the correct parts for your engine. Search by Make, HP, Stroke, Model, Year, and SN.
Select only the fields available — you don’t need to fill all options (e.g., leave Year blank if not applicable).
Our database is currently being updated and expanded. More models, including Yamaha, Mercury, and Suzuki, are being verified and uploaded.
Our database is currently being updated and expanded. More models, including Yamaha, Mercury, and Suzuki, are being verified and uploaded.
- Choosing a selection results in a full page refresh.