Customer Service: info@jlm-marine.com
Free shipping. No Minimum Purchase
Flexible Rubber Water Pump Impeller 17018-0001 – 8 Blade Neoprene 65 mm Spline – Fits JMP 7446-01
- $45.60
- $45.60
- Unit price
- per
Couldn't load pickup availability
Free Shipping
Free standard shipping on all orders
Worry-Free Returns
Learn More.
How to Match This Part
This is a flexible rubber raw water pump impeller. It sits inside the pump housing behind the cover plate and is driven by a splined shaft. It replaces the primary original part number Jabsco 17018-0001, and is also supplied against JMP 7446-01 and Caterpillar 3N5895.
Match this part by checking your engine in this order:
1. Original impeller part number (stamped on the old impeller or listed in the pump section of your parts catalog)
2. Width (this listing is 76 mm / 3 in. wide, not the 50 mm 920-0001 or 68 mm 31130-0061)
3. Drive type (this listing is a 12-spline hub, not a key drive)
4. Pump model (cast or labelled on the pump body)
Identify it physically before ordering. This impeller has eight vanes moulded in black neoprene around a machined brass 12-spline insert (Jabsco Profile M). JMP 7446-01 is 65 mm diameter, 76 mm width and 16 mm (5/8 in.) bore. It is not interchangeable with 8-blade 50 mm spline 920-0001 or 10-blade 68 mm spline 31130-0061.
- ✓ Primary OEM: Jabsco 17018-0001
- ✓ Product form: 8-blade neoprene impeller, brass 12-spline insert, 76 mm width
- ✓ Fitment: part number, then width, then drive type
Part Number Cross-Reference
Use this table to confirm equivalent part numbers. Jabsco 17018-0001P and JMP 7446-01K are kit numbers. This listing is the impeller only.
| Type | Brand | Part Number | Notes |
|---|---|---|---|
| OEM | Jabsco Pump | 17018-0001 | Primary reference. 8-blade neoprene, Profile M, 12-spline |
| OEM | Jabsco Pump | 17018-0001P | Source-sheet kit number. O-rings and lubricant are not included |
| OEM | JMP Pump | 7446-01 | Bare impeller. JMP 7446-01K adds ORG0067, ORG0071 and lubricant |
| OEM | Caterpillar | 3N5895 | JMP 7446-01 equivalent. Match the original number |
| Other brand | Industry interchange | K-1103 | Source-sheet other-brand number for this SKU |
Compatible Engine Models
Confirm the original impeller number and measure about 76 mm width on a 12-spline hub. JMP 7446-01 also lists Volvo Penta 3583602, 3593573, 3817587, 3819486 and 21730348; match those original numbers rather than a D6 or D9 family dump. Do not assume every CAT 3208 uses this part.
| Brand | Engine / Pump Model | Original Part No. | Notes |
|---|---|---|---|
| Jabsco / JMP | Pumps specified for 17018-0001 or 7446-01 | 17018-0001, 7446-01 | 8-blade, 12-spline, 65 × 76 × 16 mm |
| Caterpillar | Engines whose parts list calls for 3N5895 | 3N5895 | JMP 7446-01 equivalent. Match the original number |
| JMP pumps | JPR-VP0060DA, JPR-VP0090D, JPR-VP0110DB | 7446-01 | JMP published pump models for 7446-01. Confirm the impeller number on the pump |
Technical Specifications
| Specification | Value |
|---|---|
| Part type | Flexible rubber impeller, raw water pump |
| Number of blades | 8 |
| Impeller diameter (A) | 65 mm (2-9/16 in.) |
| Impeller width / depth (B) | 76 mm (3 in.) |
| Shaft bore diameter (C) | 16 mm (5/8 in.) |
| Insert / drive type | 12-spline |
| Insert material | Machined brass |
| Vane material | Neoprene rubber (Jabsco Profile M) |
Package Contents
This listing is for the impeller only, as shown in the impeller in the product images. Please refer to the part number cross-reference table to confirm component details.
Cover plate gasket, O-rings and lubricant are not included. Jabsco 17018-0001P and JMP 7446-01K add those service parts.
Installation Guide
- 1 Stop the engine, let it cool, and close the raw water seacock so water cannot enter the boat while the pump is open.
- 2 Remove the cover plate screws and lift off the cover. Keep the screws and the old gasket together so you can compare the seal size when reassembling.
- 3 Note the spline orientation, then grip the brass insert and pull the old impeller straight off. Recover any broken vane pieces from the downstream cooling circuit before continuing.
- 4 Clean the housing bore and the wear plate, and inspect them for scoring. Apply a marine-grade impeller lubricant, glycerine or soapy water to the bore and the new vanes. Do not use petroleum-based grease, which attacks neoprene.
- 5 Align the spline in the brass insert with the pump shaft, then press the impeller in while turning the shaft in the normal direction of rotation so all eight vanes lay over the same way.
- 6 Refit the cover plate with a serviceable gasket, tighten the screws evenly in a crisscross pattern, open the seacock, then start the engine and confirm a solid stream of cooling water and no leaks at the cover.
Note: Professional installation is recommended to ensure safety and optimal performance.
Troubleshooting & FAQ
Important Notes
- Verify that the product images and specifications match your original part. If discrepancies exist, even if your model is listed, do not proceed with the purchase.
- This product is an aftermarket replacement part and is not an OEM component.
- The impeller is supplied on its own. Cover seals and lubricant must be ordered separately if your service procedure requires them.
- This is an 8-blade, 65 mm 12-spline impeller, 76 mm wide. It will not fit 50 mm 920-0001 or 68 mm 31130-0061.
- Never run the pump dry. Even a few seconds without water will damage the neoprene vanes.
- Professional installation is recommended to ensure safety and optimal performance.
Why Choose JLM MARINE?
- Quality Assured: As a trusted manufacturer for over 20 years, we supply top marine brands globally.
- Fast Global Shipping: Free delivery worldwide in 5–15 days.
- Direct from Manufacturer: Competitive pricing without compromising quality.
We can ship to virtually any address in the world with free shipping available for most regions.
For our typical US and Canadian customers , our shipping timeframes are as follows:
- Amazon FBA: orders will be delivered within 1-5 business days after placing the order (during certain special periods such as major promotions, Christmas, etc., the delivery time of Amazon FBA may be affected).
- US warehouse shipment: orders will be delivered within 5 days after placing the order.
- China warehouse shipment: orders will be delivered about 12 days after placing the order.
When you place an order, we will estimate shipping and delivery dates for you based on the availability of your items and the shipping options you choose. Depending on the shipping provider you choose, shipping date estimates may appear on the shipping quotes page.
Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.
Founded in 2002, JLM Marine has established itself as a dedicated manufacturer of high-quality marine parts, based in China. Our commitment to excellence in manufacturing has earned us the trust of top marine brands globally.
As a direct supplier, we bypass intermediaries, which allows us to offer competitive prices without compromising on quality. This approach not only supports cost-efficiency but also ensures that our customers receive the best value directly from the source.
We are excited to expand our reach through retail channels, bringing our expertise and commitment to quality directly to boat owners and enthusiasts worldwide.
Parts Finder
Use our Parts Finder to quickly locate the correct parts for your engine. Search by Make, HP, Stroke, Model, Year, and SN.
Select only the fields available — you don’t need to fill all options (e.g., leave Year blank if not applicable).
Our database is currently being updated and expanded. More models, including Yamaha, Mercury, and Suzuki, are being verified and uploaded.
Our database is currently being updated and expanded. More models, including Yamaha, Mercury, and Suzuki, are being verified and uploaded.
- Choosing a selection results in a full page refresh.